Detach and reconnect OneDrive

Does anyone know how to detach OneDrive from a Microsoft Live account? I've added Windows 8.1 to my laptop, and log into it with my Windows Live account. I have an existing OneDrive account, also with Windows Live login, with 29GB capacity and about 20-21GB
used.
Once I used Win 8.1, the two seem to have found each other, and made all sorts of assumptions about where the offline files should be, synchronization rules, and so on. There are a couple of old files with too long path-names that prevent synchronization.
I change the names to shorten them, but the old versions keep coming back. I would somehow like to disconnect OneDrive, then reinstall if from scratch so I can set the sync folder and such. I keep trying, but don't find any useful settings at either
the Windows or the Cloud end.
It's like I created a monster but don't have the tools to recapture it. Help !!

For the record, my One-Drive problems, and there have been a lot,
were solved by a Windows update yesterday (4/15/2014)Update for Windows 8.1 64-bit (KB 2919355)
Presumably it was released for other platforms also. Make sure you run Windows update.

Similar Messages

VHD detaching and 137 & 14 errors

I have a Hyper-V server running 2012. It has 4 VMs all running 2012. The host has a removable cartridge drive which contains a VHD for each VM which is attached within each VM as a drive used by Windows Server Backup.
The problem is that sometimes, but not often, the VHD will become detached and so the backup fails. The VMs are not rebooting (which would require reattaching the VHD) so that's not the cause.
I've looked in the event log and the only errors other than the failed backup are in the System Log. Event 137 from ntfs which says "the default transaction resource manager on volume <volumeID> encountered a non-retryable error and could not
start"; and Event 14 from volsnap which says "the shadow copies of volume <volumeID> were aborted because of an IO failure on volume <volumeID>".
I tend to think the errors came after the VHDs were no longer available, but I can't be certain.
I have the same setup at other locations and they don't have this problem of the VHD randomly detaching.
Anyone run into this before and know how to fix it?
Jonathan

Hi Jonathan,
The VHD is connect through Hyper-V settings or other methods such as iSCSI?
If it is in Hyper-V settings, you may also need to check the host server and see if any reconnected occurs between the host and the removable cartridge.
If you have any feedback on our support, please send to [email protected]
The VHD is attached by using the Attach VHD menu command in Desk Management in the VM and using a UNC path. This is how we do it on all our clients with an RDX cartridge drive containing VHDs that are used by all VMs for backup drives.
As I said, this is the only client this happens to and it's very random and never do all the VHDs become detached at the same time. It's usually one or maybe two of the 4 VMs that have this happen at the same time. I believe one time 3 of the 4 had it happen.
So I don't think there would be any reconnect errors between the host and cartridge as if there were, then all VMs would experience the problem at the same time.
Jonathan

When leave I nano 4th gen connected to either of my cars it no longer restarts playing when car is restarted. Instead it shows 'no entry' in the song title on the car audio display and won't play until disconnected and reconnected.

Nano has worked fine for a couple of years being left connected to either one of our cars. However, every time car is restarted it won't play without being disconnected and reconnected. I have done a full restore.
Current cars are Range Rover Sport 2011 and Jaguar XK 2011.
Has anyone else experienced this issue?
Thanks,

I had a similar problem. Try resetting and erasing the phone and restoring from a known good backup.

Everytime i eject my ipod and reconnect it all my music is gone. and sometimes while i try adding music to it. itunes completely freezes. please help. and sometimes when i plug it back into my PC i have to rename my ipod and such

Everytime i eject my ipod and reconnect it all my music is gone. and sometimes while i try adding music to it. itunes completely freezes. please help. and sometimes when i plug it back into my PC i have to rename my ipod and such

Antivirus has a tendency to freeze iTunes sync Operation with iPod Classic, causing a timeout, which corrupt your iPod filesystem, so when iTunes can't read the iPod, it is pointing to this problem. Other causes is when your iPod hardisk is dying, or your battery is dying causing hardisk crashes.
My suggestion.
Connect your iPod to the PC and run chkdsk, to fix any iPod diskerror, then disconnect it, after chkdsk complete.
Disconnect your PC from Internet. (just to make sure no nasties creep into your system while you syncing.
Stop the Antivirus program
Connect your Ipod to the PC
When iTunes Open up, Restore your iPod please, this is for iTunes to map correctly, to fix the corrupted filesystem.
When Restore complete, eject the iPod and reconnect again.
Sync your ipod, preferably manually Manage in small batches and disconnect after every batch, to check that all is well, since you got such a huge library.
When all sync is complete, and iPod disconnected, start back your Antivirus and connect back the Internet.
If this doesn't resolve your problem, then let me know.
Good Luck!

Cannot view InfoPath Form on SHarePoint 2013 since I removed SkyDrive for Business and installed OneDrive For Business

I removed SkyDrive for Business and installed OneDrive for Business on my laptop. After that, I had problems opening a Word and Excel document in a SharePoint site (SP2013). After installing Service Pack2 from Office2010, this problem is solved.
But I still have the same problem with InfoPath. Whenever I click an InfoPath form (I have InfoPath 2010 on my laptop),...
... I get the error "cannot display web page".
When I change the URL
ms-infopath:ofe|u|http://intranet.water-link.be/samenwerken/awwit/Autorisaties/Gebruikersbeheer/2015-02-25%20Aanvraag%20gebruikersbeheer%20voor%20Stephanie%20Geeraerts.xml
into
http://intranet.water-link.be/samenwerken/awwit/Autorisaties/Gebruikersbeheer/2015-02-25%20Aanvraag%20gebruikersbeheer%20voor%20Stephanie%20Geeraerts.xml
I can open the InfoPath form and read it.
Any ideas about how to fix this ? I already tried to restore the Office 2010 via Control Panel - Install Programs but without any success...

Hi Gert,
As I understand, you can’t open InfoPath form in SharePoint 2013 unless you change the URL without “ms-infopath:ofe|u|”.
There are some reasons which maybe cause this issue, and you can try to do things below:
Access CA -> General Application Settings -> Configure InfoPath Form Service -> Check the two options in User Browser-enabled Form Templates.
Go into the registry by typing regedit from the Run line and rename the SharePoint.OpenDocuments.5 key (ex. SharePoint.OpenDocuments.5.old) under HKEY_CLASSES_ROOT.
In library settings, click "relink documents to this library".
Here are some similar posts for your reference:
http://blogs.technet.com/b/office_integration__sharepoint/archive/2014/02/24/quot-the-webpage-cannot-be-displayed-quot-when-trying-to-open-edit-an-office-file-from-a-sharepoint-2013-site.aspx
http://www.infopathdev.com/forums/t/28998.aspx
Thanks,
Wendy
TechNet Community Support
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact
[email protected]

Greetings, I am working in Final Cut Pro 7. In the timeline some clips show as offline. I tried going to sequence and reconnecting to media but it does not work. I can still see the video in the timeline and work with it. It just has the red box.

Greetings, I am working in Final Cut Pro 7. In the timeline some clips show as offline. I tried going to sequence and reconnecting to media but it does not work. I can still see the video in the timeline and work with it. It just has the red box. Thanks! Olga

If the clips are not actually missing, you could try to refresh the timeline by using cmd-0 and then going to the timeline options tab. Then select name only where it says "thumbnail display". Press ok to accept the change, then repeat the process to add thumbnails back to your timeline.

Adobe photoshop cc 2014 crashes at startup / GC driver up to date (nvidia 740M) / windows 8 / uninstalled software reinstalled disconnected creative cloud and reconnect / nothing solved /error report ready to send

Help
in this for 3 and a half hours now and really nervous bout it.
adobe photoshop cc 2014 crashes at startup /
solely photoshop : lightroom illustrator indesign okay /
GC driver up to date (nvidia 740M) /
windows 8 /
uninstalled software and reinstalled from creative cloud app /
disconnected profil creative cloud and reconnect /
moved preferences out /
I just have installed a fresh OS windows 8 and nothing but the adobe apps /
nothing solved /error report ready to send
(edit)
funny cannot send the image of the errors because i DO NOT have a photoshop working version !)
(did the screen copy, exported in jpeg srgb from illustrator)

exported the error log from lightroom still not working as it seems like the file (it's a screenshot) is more than a 8mo size file !
i ignored i was using a 8k screen till now
please help
Cheers,
Arnaud.

Virtual RAID Array Migration to Windows Server 2012 R2 Disk offline, Degraded, Detached and split

My Residential server is used as a file and web server, however i also use it for learning so it has grown slow over the last couple of years, i now need to get it working ready for when i go to UNI. I have upgraded from windows server 2012 Standard to windows
server 2012r2 standard, i am on the same server, but have put a SSD as my primary drive(so i still have the old hard drive and can go back to that to get my data)
I have also done a BIOS update, so the logical disks (a 2TB RAID 1 with all my important documents) are not showing up on the RAID Configuration in the BIOS.
By changing settings i have managed to get the array to show up on server manager > File and storage services>Volumes>Storage Pools. however there are a number of exclamation marks shown next to the drive(s)
I read in a Technet
Article that i should "set
the storage pool to read-write "
I did this and then in the storage pool box at the top the exclamation mark says "Warning: Degraded".
In the Virtual Disks box (bottom left) the exclamation mark says "Unknown: Detached" and in the Physical Disks box (bottom right) it says "Warning Split" on the second disk.
I have disconnected all other Hard drives, however if i can't get my documents back will have to go back to windows server 2012. Any ideas would be greatly appreciated.
Michael Booth

Hi,
It seems that the second disk is failed, you need to add a new disk to the storage pool to replace the failed disk.
Degraded Storage Spaces Storage Pool after single HDD failure
http://social.technet.microsoft.com/Forums/en-US/3a7e2a7d-4ad7-48cc-8165-0d6673e37436/degraded-storage-spaces-storage-pool-after-single-hdd-failure?forum=winserveressentials
Regards,
Mandy
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Error message says "an ipod has been detected but it could not be identified. We've disconnected the ipod and reconnected it but it hasn't worked.

error message says "an ipod has been detected but it could not be identified. We've disconnected the ipod and reconnected it but it hasn't worked.

If the iPod was originally formated to your computer, restart your computer. If not - How to use your iPod to move your music to a new computer

TS3474 iTunes has detected an iPod that appears to be corrupted. You may need to restore this iPod before it can be used with iTunes. You may also try disconnecting and reconnecting the iPod.

What do I do about this message? I've restored it 3 times, but this message still comes up, and i cannot put music on it now.
iTunes has detected an iPod that appears to be corrupted. You may need to restore this iPod before it can be used with iTunes. You may also try disconnecting and reconnecting the iPod.

Sounds like your iPod is broken. Take it to Apple or someone else who repairs iPods and see if you can get it fixed, or get it replaced.

In Windows 7, iTunes gives error message "An iPhone has been detected, but it could not be identified properly. Please disconnect and reconnect the phonon then try again.

In Windows 7, iTunes gives error message "An iPhone has been detected, but it could not be identified properly. Please disconnect and reconnect the phonon then try again."
I have a iphone 4S. It has been activated on Win 7 computer and synced. But overnight this meassage reappears.

I have same error except that i get it even when my phone is not connected.

Podcasts no longer appear under ipod device in I tunes library. I can access podcasts on my ipod but I CANNOT access podcasts on I tunes library. I have disconnected and reconnected. I have restored my ipod. I have checked for updates. What else?

'Podcasts' under Ipod device disappeared in Itunes library. I can't manage my podcasts on ipod via I tunes library. I can access the podcasts on my ipod (5th generation), itself. I can access and manage music. I can add more podcasts to ipod. The podcast icon reappears with only the newly added podcasts. When I disconnect ipod and reconnect ipod, 'podcasts' no longer appears under the device. So I am unable to manage my podcasts on I tunes library which means I can't delete podcasts from I tunes library. I can only add podcasts. I have disconnected and reconnected ipod. I have checked for updates. I have restored the ipod to it's original settings. My next step will be to install and reinstall I tunes. Any other suggestions would be appreciated.

To be clear, the podcast icon disappeared under Ipod device in Itunes. I can access and manage the podcasts in the itunes library. I can't manage podcasts on my ipod via itunes (which means I can't delete podcasts from my ipod). I can access podcasts on my ipod, itself.

How can I troubleshoot this problem with the iMac keyboard? My keyboard disconnects and reconnects within seconds but all the typing is lost while it was offline. This is usually 5 seconds or less but happens 2 or 3 times in a minute. Annoying!

My wireless keyboard disconnects and reconnects within seconds but all text that was typed during the time offline is missing. i have to go back and retype missing parts. What can I do to troubleshoot this. The computer is only about six month old. This problem is new in the last couple weeks. Thanks for suggestions.

Beat me to it, Donald. But there is a possible alternative. If the batteries have been replaced since new, were they replaced with the same batteries or another make. There are examples around which do not fit perfectly and leave a certain amount of movement inside the battery housing. That could lead to instability such as the OP describes.

Time Capsule disk disconnect and reconnect every 5 minutes

This problem began with Airport Firmware 7.6, and has continued to perist with every subsequent firmware version. Reverting to firmware version 7.5.2 eliminates the problem. Running with the latest firmware version 7.6.3, on OS X 10.8.2, the Time Capsule disk is disconnected and reconnected every 5 minutes, and this is seen in the console log:
15/02/2013 16:10:22.344 KernelEventAgent[43]: tid 00000000 received event(s) VQ_NOTRESP (1)
15/02/2013 16:10:22.344 KernelEventAgent[43]: tid 00000000 type 'afpfs', mounted on '/Volumes/Vilya', from '//Mike%20Connally@TimeCapsule._afpovertcp._tcp.local/Vilya', not responding
15/02/2013 16:10:22.000 kernel[0]: ASP_TCP Disconnect: triggering reconnect by bumping reconnTrigger from curr value 190 on so 0xffffff804456ede0
15/02/2013 16:10:22.000 kernel[0]: ASP_TCP asp_tcp_usr_control: invalid kernelUseCount 0
15/02/2013 16:10:22.000 kernel[0]: AFP_VFS afpfs_DoReconnect started /Volumes/Vilya prevTrigger 190 currTrigger 191
15/02/2013 16:10:22.000 kernel[0]: AFP_VFS afpfs_DoReconnect: doing reconnect on /Volumes/Vilya
15/02/2013 16:10:22.000 kernel[0]: AFP_VFS afpfs_DoReconnect: posting to KEA EINPROGRESS for /Volumes/Vilya
15/02/2013 16:10:22.000 kernel[0]: AFP_VFS afpfs_DoReconnect: Max reconnect time: 30 secs, Connect timeout: 15 secs for /Volumes/Vilya
15/02/2013 16:10:22.000 kernel[0]: AFP_VFS afpfs_DoReconnect: connect to the server /Volumes/Vilya
15/02/2013 16:10:22.345 KernelEventAgent[43]: tid 00000000 found 1 filesystem(s) with problem(s)
15/02/2013 16:10:22.000 kernel[0]: AFP_VFS afpfs_DoReconnect: Logging in with uam 13 /Volumes/Vilya
15/02/2013 16:10:22.651 KernelEventAgent[43]: tid 00000000 received event(s) VQ_NOTRESP (1)
15/02/2013 16:10:22.000 kernel[0]: AFP_VFS afpfs_DoReconnect: Restoring session /Volumes/Vilya
15/02/2013 16:10:22.000 kernel[0]: AFP_VFS afpfs_DoReconnect: get the reconnect token
Has anyone found a solution to this, other than reverting to Airport Firmware 7.5.2?

Welcome to the club.. there is a very long thread.. here.
https://discussions.apple.com/thread/3526741?tstart=0
There seems to be any number of factors.. where the solutions are little silly things..
Start from the end of the thread and work backwards as this has been ongoing for a long time.. and experience has improved.
What you are seeing btw is the change apple made in Lion and 7.6 to higher security version of AFP.. but it is a mess IMHO.. and has not worked at all well.

How to disconnect internet connection in Time Capsule and reconnect without restarting the whole device?

Hi, I would be very grateful if someone could tell me how to disconnect internet connection in Time Capsule and reconnect without restarting the whole device?
The thing is that as I have a dynamic IP address, everytime I restart the internet connection my IP address changes. I sometimes need it to change, so I need to restart the connection. I don't know another way to restart the connection than restarting the whole Time Capsule.
Thanks!!
PD: the computer I use is Windows based, using the Airport Utility for Windows, but I also have a MacBook Pro I could use and an iPhone too.

The utility in windows is very like Mac so the screenshots are from Mac as I don't have windows available now.
How this works depends on the setup of the TC.. which you did not tell us.. you cannot change anything if you do not have the TC as the main router in the network.
So on the internet tab you need to share a public IP address.
On the next tab where you set IP address.
Click the renew IP address.
It might work.. and it might not.. the problem is you are not disconnecting the network.. sometimes the hard disconnection is required before the address will renew..
What about unplugging the WAN port.. then click renew the IP which will fail.. then plug the wan back in again.
In the end it is easier and faster to power cycle the TC.

Detach and reconnect OneDrive

Similar Messages

Maybe you are looking for