Detail workflow for site survey?

Hi All,
I am new in this field. I had saw some information and I can catch the basic meaning of wireless LAN. But I can not find any information about the detail workflow when doing site survey and how to work when an AP doing as site survey client, also when a bridge work as a repeater. When will a client doing a site survey? and the detail workflow of site survey? Is there any problem that may make site survey fail? Does any body know it? Can any body give me a hand? Thank You!
Best Regards
Teru Lei

Here are a few URL's that should help you with the site survey. These links have a list of things that could interfere with the site survey. http://www.cisco.com/univercd/cc/td/doc/product/wireless/airo_350/350cards/windows/incfg/win5_apf.htm http://www.cisco.com/univercd/cc/td/doc/product/wireless/airo_350/accsspts/ap350scg/ap350ch3.htm#1016921

Similar Messages

  • Configuring 1142 to use for site survey.

    Just got in a bunch of the 1142 N-A-K9 APs. I need to set them up to do a site survey with.
    Don't seem to be able to find anything on the site.
    Has anyone used yet for site surveys? The radios are off by default.

    You can survey with 1142. You can do two ways in lightweight mode. One would be to use it with 2106. This could be cumbersome as you have to carry around UPS so you can power the 2106 and use PoE on 2106 to power 1142. This way you can adjust channels and power levels on the AP as you see fit from cell to cell. Second method would be to configure the AP for HREAP mode on the controller and assign your custom power levels and channels. Then you can just use that AP without the controller to survey and power it up thru a PoE battery pack. The custom power levels stay on both 2.4 and 5 GHZ radios but channel only stays on 2.4GHz. Due to FCC and DFSS the 5GHz channel will most likely change each time you boot the AP. If you keep the AP on the battery pack for the duration of the survey it will stay on the same channels. So the negative to the HREAP mode survey is that you can't adjust channels and power levels as you move from cell to cell easily as you would have to connect it back up to the controller. Surveying with 1142 is helpful as from my experience they have a better footprint than 1131s. Hope this helps.

  • Cisco 3502i in autonomous mode - for site survey

    Hi,
    Last year I was able to load autonomous mode IOS to a cisco 3502i to do the site survey using instructions at following thread.
    https://supportforums.cisco.com/thread/2084624
    This year I have to do site survey for a different site and need to do the same process. However on the CCO I don't see the autonomous image. Under downloads -> products -> wireless -> access points -> Cisco 3502i I see IOS link and when clicked there is gives
    ap3g1-k9w8-tar.124-23c.JA4.tar. I even loaded that IOS but it seems to be light weight mode IOS.
    After reading a few different threads somebody clarified that K7 = IOS and K8 = Lightweight. However I can't seem to find the lightweight mode anywhere.
    https://supportforums.cisco.com/thread/2140629
    Can somebody guide me? I need to run this code only for the site survey and totally understand the fact that Cisco would not support such configuration.
    Thanks in advance,

    Sorry to inform you but there is no autonomous code for the 3500. You could however use the 1140 code. But this not supported by Cisco but it does work ..
    Sent from Cisco Technical Support iPhone App

  • Config for using 1242 for site survey

    Hello, i'm helping a coworker, we have a 1242 and would like to use it for a site survey, but we are not able to activate the radio using conf t it is in light weight, are we missing something? were can i find a config example to use for this purpose?

    Hi Alfred,
    Converting a Lightweight Access Point Back to Autonomous Mode
    You can convert an access point from lightweight mode back to autonomous mode by loading a Cisco IOS Release that supports autonomous mode (Cisco IOS release 12.3(7)JA or earlier). If the access point is associated to a controller, you can use the controller to load the Cisco IOS release. If the access point is not associated to a controller, you can load the Cisco IOS release using TFTP.
    Using a TFTP Server to Return to a Previous Release
    Note This section does not apply to Cisco C3201WMIC and Cisco C3201LAP.
    Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release using a TFTP server:
    Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.
    Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
    Step 3 On the PC where the TFTP server is located, perform these steps:
    a. Disable any software firewall products, such as Windows firewall, ZoneAlarm firewall, McAffee firewall, or others.
    b. Ensure all Windows files are visible. From Windows Explorer, click Tools > Folder Options > View > Show hidden files and folders.
    Step 4 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, c1240-k9w7-tar.default for a 1240 series access point, and c1250-k9w7-tar.default for a 1250 series access point.
    Step 5 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
    Step 6 Disconnect power from the access point.
    Step 7 Press and hold MODE while you reconnect power to the access point.
    Step 8 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.
    Step 9 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.
    Step 10 After the access point reboots, reconfigure it using the GUI or the CLI.
    http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp161272
    Hope this helps!
    Rob

  • Question about WLAN Site Surveys with 802.11n APs - 1142s

    I do site surveys a little differently that everyone else nowadays, I believe.  In the past, I used an autonomous 1230 or 1240, but now I use a lightweight 1142.  I configure a port in a room to be on the AP VLAN and I connect my 1142 to the port and hang it where I want - it then gets on the controller and start broadcasting just like the finished product will.  This works well except for the time it takes me to configure a port on the switch and the bootup time for the AP.  I'm one of the Networks Architects on a campus of almost 200 buildings, so I have access to all the routers and switches and can configure anything I need while onsite.
    Now I want to have someone else (in-house) to do our surveys - but this person(s) does not have access to switches and routers, and that won't ever change.
    I tried configuring a lightweight 1142 in HREAP mode to handoff to this person, but it appears the power and channel settings don't stick on the 5 GHz side.
    Scrapping that idea, I now have to build out an autonomous 1142 for site surveying.  I missed out on this step because I went from buying 1242s (can jump between lightweight and autonomous) to 1142s (which didn't have an autonomous image at that time, I believe).  This is why I started surveying with lightweight 1142s.
    I'm curious if anyone has gone through the configuration of an autonomous 1142 and wouldn't mind sharing their "lessons learned".  I haven't seen a matrix of features that are supported/not supported on 1142s when configured for lightweight vs. autonomous.
    I currently aim for designing around the 5 GHz radios set to 10 dBm, 20% cell overlap.  I also turn on 40 MHz channels in 5 GHz range.  This usually ends up with an AP in every other or every third classroom, depending on how old the building is and how many times it has been renovated.  I can't "just throw APs out there" since each building is different - some are thin concrete block, some are poured cement, and some are block with metal mesh and stucco.  Those usually end up with on AP per classroom.
    Does anyone have a matrix on what can and cannot be turned on in an autonomous AP?  I would like to get my config as close to the lightweight scenario we deploy for all of our production WLANs.

    There is no matrix as to what you're asking for. I've done conversions and configurations of AP's from Lightweight to Autonomous and vice-versa. The configuration of the autonomous AP can be identical to the Lightweight AP from a client perspective.
    My current setup has 3 SSID's (VoIP, Data, and Guest) on the autonomous AP. Couple things I do:
    1. PoE powered AP through a Tessco power pack.
    2. VLANs have to be enabled on the AP (1 for each SSID)
    3. The SSID's will have to be created and each AP mapped to a VLAN
    4. The SSID's will be need to be enabled on both radios if desired.
    The easiest way to configure the AP is to power it with either the power cord.
    Console into the AP and let it boot. Assign an IP address to the BVI 1 interface.
    Assign an IP address on the wired NIC of our laptop and plug an ethernet cable into the AP's ethernet port.
    Configure the AP as listed above via the web gui.
    This is by no means a complete answer, but your questions were all over the map.
    Regards,
    Jerry

  • Showing Full AP name in cisco Wireless phone 7921-site survey

    Hi,
    I am working on a project where cisco wireless phone 7921  is utilized. We use phones sitesurvey tool for coverage tests. Our AP names are 18 characters in length and are not dispayed in full in site survey screen. Please suggest on a way to increase the display character count in the site survey or to make it a running text. Thank you.
    Regards,
    Madhan kumar G

    Hi Leo,
    Thanks for the suggestion. I looked at the Fluke OptiView XG Network Analysis Tablet. Looks very interesting, but looking at the cost of the Tablet, I am pretty sure that my Employer will say NO.
    Anyways, Can you recommend some vendor options (It will be really helpful, if you can share the Model information as well) for the list highlighted below.
    1. AP Tripod (Reaches 3 meters max) - Need recommendation on AP Telescopic Tripod which should be portable to carry in the Peli Case.
    2. Distance measuring tool - Need recommendation on this.
    3. Laptop harness - I did some research and found Connect-A-Desk Laptop Harness, which I am planning to purchase
    Also, I need your inputs in choosing Antennas for Site-Survey Kit (I am looking at must to have options for the Kit).
    Thanks,
    CJ

  • Site Survey with ap3500i

    Hey,
    I have a question about sitesurveying with ap3500's
    I'm going to deploy a wireless network in a new building, i have a company that normaly does my site surveys.
    I normally provide them with some AP's configured with a designated ssid and local power modes set to 50%, however this does not seem possible with the new 3500i's i'm willing to use, for there is no IOS image available for it.
    I dont have any network connectivity yet in this new building, so i cannot f.i place them in a separate ap-group and assign a dedicated wlan to them.
    Can Anybody think of a viable solution (ASAP) Thanx in advance
    Frans verschoor

    leolaohoo wrote:We use 1140s for site surveys in our 3502i deployments.Not recommended.
    I have the same questions as Thomas. In the thread below I tried to find out any differences between these APs but the consensus was that ClearAir was the only notable difference. The only way the 1140 would be not recommended for a passive survey is if there is differences in the antenna pattern, and active survey if there's a difference in chipset or hardware. So what are the differences?
    https://supportforums.cisco.com/message/3398804#3398804

  • Wireless RF Site Survey Tools: Do you have a preference?

    Our customers are asking us with greater frequency to work with them on deploying high performance wireless networks that are secure, reliable and support end-to-end QOS. We recognize to do that professionally requires great site survey RF tools.
    We are considering AirMagnet's "Survey Pro" with their integrated "Spectrum Analyzer." We would run them on a Lenovo 802.11abg PC.
    However we have seen some discussion on here regarding Cognio's Spectrum Analyzer and we have also found the Exahau "Site Survey" software product will speak with a Fluke 802.11 radio.
    We are looking at investing in a tool set for our Wireless practice and we want to ask you what are your favorite site survey and spectrum analyzer tools? Thanks for taking the time to respond!

    Apart from all the features Sales folks pitch about from both these companies the intuitiveness (ease of use) and accuracy make a lot of difference.
    I would suggest getting trial copies of both of these tools and using them in the field before making a final investment.
    Personally I have used AirMagnet Spectrum Analyzer (a separate product) and has been impressed by it. It comes in both laptop as well as handheld formats.
    For site surveys I have used Wireless Valley which is also very impressive.

  • Help with first time "controller based" Site Survey

    We are moving from autonomous 1242AG to "2500 LAP with 2600 WLC"
    I am used to bringing 1 autonomous AP to do my Site Surveys, but now that that I have a LAP, does it mean I need to bring a Wireless Controller with me so that the LAP could join it?
    What do you guys do? Bring WLC, LAP and small UPS?
    Any ideas would be helpful
    Thanks!

    Hi,
    If you only have a LAP now then also you can convert to autonomous AP and do the site survey and then convert back to Lightweight.
    You just need the 2 images.
    One autonomous image:k9W7
    http://software.cisco.com/download/release.html?mdfid=284362264&flowid=34154&softwareid=284180979&release=15.2.4-JB4&relind=AVAILABLE&rellifecycle=ED&reltype=latest
    One lightweight image: k9W8
    http://software.cisco.com/download/release.html?mdfid=284362264&flowid=34154&softwareid=280775090&release=15.2.4-JB4&relind=AVAILABLE&rellifecycle=ED&reltype=latest
    Site survey is nothing to do with WLC(You can go ahead with Autonomous AP for site survey).
    On the same place put the LAP and connect to nearest switch.
    WLC push the config to LAP and also manages the RRM feature(Power, Channel....).
    Regards
    Dont forget to rate helpful posts

  • Sending Reminders for SharePoint Survey

    Hi,
    Is there anyway to generate a SharePoint survey in such a way that, it is sent out as a task to all the responders and a due date is set by which they are supposed to respond. As the due date is approaching, is it possible to send a reminder?
    A default SharePoint Survey list App does not offer this functionality. Any approach using SharePoint workflows?
    Thanks,
    techie

    techie,
    In that case above solution will not work as they will run on each item. But you want a workflow
    for a survey list and wanted to send reminder email to them who didn't responded to survey yet.
    For that I will suggest you
    to create a list of user who need to respond to survey
    Create a custom timer job which will run daily(configurable anyway) and check whole survey respond and above list to identify who didn't participate yet.
    then will send a email.
    How to create a SharePoint custom timer Job
    Create and Deploy Custom Timer Job Definition
    in SharePoint Programatically
    Creating Custom SharePoint Timer Jobs
    Step
    by Step procedures to create a Timer Job in SharePoint 2013
    Please 'propose as answer' if it helped you, also 'vote helpful' if you like this reply.

  • HT1918 i have recently moved from the uk to australia and cancelled my uk debit before the payment was processed for songs i bought in itunes. i have tried to edit my billing info with australian debit details but the site says 'invalid card' how can i fi

    i have recently moved from the uk to australia and cancelled my uk debit before the payment was processed for songs i bought in itunes. i have tried to edit my billing info with australian debit details but the site says 'invalid card' how can i fix this?

    Contact iTunes Customer Service and request assistance
    Use this Link  >  Apple  Support  iTunes Store  Contact

  • Looking for a beginners guide ot site survey

    Good evening,
    Getting ready to do a site survey of a rather large facility... About to switch to an entirely different wireless nic (intel 3945ABG) which isnt performing as well as its cousin, 2200BG. Reviewing the stats of the cards it doesnt make sense as intel claims (from my understanding) the 3945 is more sensitive.
    Given the sheer size (220,000+ sq feet) of my facility i want to ensure i do this correctly the first time around. I have the given equipment which will be deploying this card.
    What i have done in the past for resolving some issues is going every 5 feet and recording by hand the SNR using something along lines of netstumbler. Is this correct?
    any suggestions will be great.

    Hi Robert,
    Here is some info that may help;
    Wireless Site Survey FAQ
    http://www.cisco.com/en/US/tech/tk722/tk809/technologies_q_and_a_item09186a00805e9a96.shtml
    This Excel macro tool is designed to work with NetStumbler to help you complete a wireless site survey. While running NetStumbler, the macro allows you to timestamp your live access points, collect signal levels of each access point, and export the raw NetStumbler data to create a handy report.
    http://whitepapers.zdnet.com/download.aspx?docid=177121&promo=100400
    Hope this helps!
    Rob

  • Wireless Site-Survey for High Density Environment

    Hi,
    I have done many Wireless SIte-Surveys in my career. But this will the first time, I am going to do a Site-Survey for High Density environment (School with Byod 1:1 design).
    Currently, the school has a Wireless network in place. The current wireless design includes 3502 APs, 5508 WLC and Cisco Prime. The customer has issues with sufficient bandwidth in classrooms which limiting the students and teachers to access the learning content.
    It is understood that there was no initial Site-Survey conducted, the AP positioning was made based on their knowledge.
    Now, I am not sure as how to conduct the Survey here?
    Do I need to conduct an Active Survey by connecting to the existing Wireless Network in the School? Or just passive Survey will be enough to determine the exact issues with the current design and provide the recommendations?
    I have gone through the Cisco High Density design and white papers to start with.
    Thanks,
    CJ

    Before you do the site survey, I'd do the initial breakdown of the LAN.
    1.  What kind of switch ports are we talking about?
    2.  Are the APs connected AND negotiated to 1 Gbps ports?
    3.  What is/are the switch uplinks?  100 Mbps, 1- or 10- Gbps, Etherchannel?
    4.  Line errors on the links between the AP and the switch, uplinks and the link between the WLC and the switches?
    5.  WLC link?  How many are used?  Are they LAG or not?
    6.  Configuration of the WLC must be checked.
    Once you've checked these do I start talking about wireless:
    1.  What problems are the staff/students experiencing?
    2.  How many APs to a classroom?  How big is the class?
    3.  Determine what kind of traffic are each class trying to push?
    4.  Where are the APs located in relations to the staff/student?
    5.  Verify co-channel interferrence.  I know they have 3502 but I've seen people disable CleanAir.
    6.  Verify what kind of NIC cards are used and whether drivers have been updated or not.
    I'm in the middle of improving our wireless coverage in >98 schools.  This means I am now deploying 1 AP per classroom.  In areas where the students/staff converge, I put additional APs (both indoors and outdoors).

  • Best practice power setting when doing a Site Survey for VOIP

    Hi Team,
    Can someone please confirm or correct me.  When doing a Wireless Active Site Survey for Cisco VOIP, I should be setting the Test AP to local power of 14, which is 25mW?  Is this correct, or should it be another value?  I asked the customer for the power of their weakest client and they do not know, but they claim there's a high probably that they will go with Cisco VOIP clients.
    Thanks...

    When you check the signal coverage, make sure the AP's radio transmit power does not use a transmit power greater than what the client devices can support. For example, by default, the Cisco Unified Wireless IP Phone 7925G uses the highest available transmit power by default (17 dBm / 50 mW for 2.4 GHz and 16 dBm / 40 mW for 5 GHz). It is possible to have a survey report that shows good coverage in all areas; however, if you have APs that operate at the highest transmit power, you might still experience uplink issues where the client devices do not support the same transmit power. For areas where there is deficient coverage, and you increase the AP transmit power to levels that the client devices cannot support, this only increases coverage on the downlink.
    Link for the same :-
    http://www.cisco.com/c/en/us/support/docs/wireless/5500-series-wireless-controllers/116057-site-survey-guidelines-wlan-00.html

  • Wireless site survey planner tool for multi floor office building

    Hi,
    I'm looking a wireless site survey planner tool for multi floor office building to estimate the number of APs and location. Not the site survey after install APs.
    AigMagnet is excellent for single floor but cannot provide multi floor scenario via planner feature even it merging capable with site survey after APs installation.
    Any tools can provide the planner tool for multi floor office building?
    Thanks in advance,

    Cj
    If you are looking for an AP estimate you can simply do the sq feet divided into the grade of wireless. For example
    You have a 100,000 feet building. All 100,000 sq feet will be wireless.
    Data 5,000 - 6.000 sq feet per AP or 100,000 / 5,000 = 20 access points
    VoIP 2,500 sq feet per AP or 100,000 / 2,500 = 40 access points
    I always like to pad it by another 10%.
    I hope this helps …

Maybe you are looking for

  • Install Enterprise Manager Grid Control 11R1 Failed at OMS Configuration

    Hello: I have installed Oracle 11g (11.2.0.1) and WebLogic Server (WLS) 10.3.6.0 and currently I am in the process of installing Enterprise Manager Grid Control 11R1 on a Linux RedHat 5.8 and it fails at OMS Configuration. I have read the following t

  • Why can't i sign in to firefox

    can't sign in, won't send me e-mail to change my password- please help!

  • Can't stream to multiple speakers.

    Just got a second Airport Express for my birthday and I connected it to my network. When I try to stream to more than one base station it says that neither supports playback as part of a group. I can do my computer's speakers and either base station;

  • SMW2 - Inbound , need to set STOP jobs to automatically delete

    Hi We set the system to receive data from ECC 6.0 system to SRM to inbound queue (SMQ2). There was specific data that we needed for processing and the other set to STOP in SMQ2. The ones that are in the QUEUE are holding back the the active one. We h

  • Nikon D300 and Aperture2

    I just bought a Nikon D300 and seem to be having some problems with the RAW conversion. From what I can tell, the D300 should be compatible with Aperture2 and Leopard. Sometimes when I make an adjustment to a photo, even the slightest adjustment will