/dev/ttya connection problem

Good Afternoon,
I have a Solaris 10 x86 U6 system installed. It is setup with a Global zone and ACSLS software running in a non-Global zone. The problem that I having is after a reboot of the Global zone, it can take up to 15 min for /dev/ttya to become available for the ACSLS software(It is a serial connection to the LSM). In my zonecfg, I have added :
<fsoption name="nodevices"/>
</filesystem>
<device match="/dev/ttya"/>
Eventually, the serial port will become active and ACSLS communication will start. Is there anything that I can set to make this port start up faster?
Thanks in advance.

Darren,
Thanks for the response. I should have posted the error message but was in a hurry. Here's the message that we see on the screen after we attempted to login to the non-global zone after a global zone reboot:
2009-07-02 02:09:34 ACSLH[0]:
1140 N Lm_ttyVopen.C 1 142
Lh error: Lm_tty::Vopen: ACS 0: port /dev/ttya: open failed, errno = 6.
Like I said earlier, this can go on for at least 15 min. We have to keep logging out of the non-global zone and back in. Eventually the error will go away and we have communication. This only started when we replace a Ultra 10 running Sol 9 with this x86 system.
I don't have anything in the Global zone that I can test this problem with. The Global is just a normal install with a patch cluster installed:
SunOS z-dm-acsls 5.10 Generic_138889-08 i86pc i386 i86pc
I can open a case with support but I thought that I would try here first.
Thanks for any help.
Doug

Similar Messages

Having connection problems with Mail after installing 10.9.4

I upgraded to 10.9.4 a few days ago, and ever since, I've been having connection problems with Mail. First, it stops downloading new mail automatically and second, it won't send any of my messages. When I try to send, I get a message that it is unable to connect.
Quitting Mail and restarting it seems to clear the problem, but then it happens again, maybe an hour or two later.

1. This procedure is a diagnostic test. It changes nothing, for better or worse, and therefore will not, in itself, solve the problem. But with the aid of the test results, the solution may take a few minutes, instead of hours or days.
Don't be put off merely by the seeming complexity of these instructions. The process is much less complicated than the description. You do harder tasks with the computer all the time.
2. If you don't already have a current backup, back up all data before doing anything else. The backup is necessary on general principle, not because of anything in the test procedure. Backup is always a must, and when you're having any kind of trouble with the computer, you may be at higher than usual risk of losing data, whether you follow these instructions or not.
There are ways to back up a computer that isn't fully functional. Ask if you need guidance.
3. Below are instructions to run a UNIX shell script, a type of program. All it does is to collect information about the state of the computer. That information goes nowhere unless you choose to share it. However, you should be cautious about running any kind of program (not just a shell script) at the behest of a stranger. If you have doubts, search this site for other discussions in which this procedure has been followed without any report of ill effects. If you can't satisfy yourself that the instructions are safe, don't follow them. Ask for other options.
Here's a summary of what you need to do, if you choose to proceed:
☞ Copy a line of text in this window to the Clipboard.
☞ Paste into the window of another application.
☞ Wait for the test to run. It usually takes a few minutes.
☞ Paste the results, which will have been copied automatically, back into a reply on this page.
The sequence is: copy, paste, wait, paste again. You don't need to copy a second time. Details follow.
4. You may have started the computer in "safe" mode. Preferably, these steps should be taken in “normal” mode, under the conditions in which the problem is reproduced. If the system is now in safe mode and works well enough in normal mode to run the test, restart as usual. If you can only test in safe mode, do that.
5. If you have more than one user, and the one affected by the problem is not an administrator, then please run the test twice: once while logged in as the affected user, and once as an administrator. The results may be different. The user that is created automatically on a new computer when you start it for the first time is an administrator. If you can't log in as an administrator, test as the affected user. Most personal Macs have only one user, and in that case this section doesn’t apply. Don't log in as root.
6. The script is a single long line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, though you may not see all of it in the browser window, and you can then copy it. If you try to select the line by dragging across the part you can see, you won't get all of it.
Triple-click anywhere in the line of text below on this page to select it:
PATH=/usr/bin:/bin:/usr/sbin:/sbin:/usr/libexec;clear;cd;p=(Software Hardware Memory Diagnostics Power FireWire Thunderbolt USB Fonts SerialATA 4 1000 25 5120 KiB/s 1024 85 \\b%% 20480 1 MB/s 25000 ports ' com.clark.\* \*dropbox \*GoogleDr\* \*k.AutoCAD\* \*k.Maya\* vidinst\* ' DYLD_INSERT_LIBRARIES\ DYLD_LIBRARY_PATH -86 ` route -n get default|awk '/e:/{print $2}' ` 25 N\\/A down up 102400 25600 recvfrom sendto CFBundleIdentifier 25 25 25 1000 MB com.apple.AirPortBaseStationAgent 464843899 51 );N5=${#p[@]};p[N5]=` networksetup -listnetworkserviceorder|awk ' NR>1 { sub(/^$[0-9]+$ /,"");n=$0;getline;} $NF=="'${p[26]}')" { sub(/.$/,"",$NF);print n;exit;} ' `;f=('\n%s: %s\n' '\n%s\n\n%s\n' '\nRAM details\n%s\n' %s\ %s '%s\n-\t%s\n' );S0() { echo ' { q=$NF+0;$NF="";u=$(NF-1);$(NF-1)="";gsub(/^ +| +$/,"");if(q>='${p[$1]}') printf("%s (UID %s) is using %s '${p[$2]}'",$0,u,q);} ';};s=(' /^ *$|CSConfigDot/d;s/^ */ /;s/[-0-9A-Fa-f]{22,}/UUID/g;s/(ochat)\.[^.]+(\..+)/\1\2/;/Shared/!s/\/Users\/[^/]+/~/g ' ' s/^ +//;5p;6p;8p;12p;' ' {sub(/^ +/,"")};NR==6;NR==13&&$2<'${p[10]} ' 1s/://;3,6d;/[my].+:/d;s/^ {4}//;H;${ g;s/\n$//;/s: [^EO]|x([^08]|02[^F]|8[^0])/p;} ' ' 5h;6{ H;g;/P/!p;} ' ' ($1~/^Cy/&&$3>'${p[11]}')||($1~/^Cond/&&$2!~/^N/) ' ' /:$/{ N;/:.+:/d;s/ *://;b0'$'\n'' };/^ *(V.+ [0N]|Man).+ /{ s/ 0x.... //;s/[()]//g;s/(.+: )(.+)/ (\2)/;H;};$b0'$'\n'' d;:0'$'\n'' x;s/\n\n//;/Apple[ ,]|Intel|SMSC/d;s/\n.*//;/\)$/p;' ' s/^.*C/C/;H;${ g;/No th|pms/!p;} ' '/= [^GO]/p' '{$1=""};1' ' /Of/!{ s/^.+is |\.//g;p;} ' ' $0&&!/ / { n++;print;} END { if(n<200) print "com.apple.";} ' ' $3~/[0-9]:[0-9]{2}$/ { gsub(/:[0-9:a-f]{14}/,"");} { print|"tail -n'${p[12]}'";} ' ' NR==2&&$4<='${p[13]}' { print $4;} ' ' END { $2/=256;if($2>='${p[15]}') print int($2) } ' ' NR!=13{next};{sub(/[+-]$/,"",$NF)};'"`S0 21 22`" 'NR!=2{next}'"`S0 37 17`" ' NR!=5||$8!~/[RW]/{next};{ $(NF-1)=$1;$NF=int($NF/10000000);for(i=1;i<=3;i++){$i="";$(NF-1-i)="";};};'"`S0 19 20`" 's:^:/:p' '/\.kext\/(Contents\/)?Info\.plist$/p' 's/^.{52}(.+) <.+/\1/p' ' /Launch[AD].+\.plist$/ { n++;print;} END { print "'${p[41]}'";if(n<200) print "/System/";} ' '/\.xpc\/(Contents\/)?Info\.plist$/p' ' NR>1&&!/0x|\.[0-9]+$|com\.apple\.launchctl\.(Aqua|Background|System)$|'${p[41]}'/ { print $3;} ' ' /\.(framew|lproj)|\):/d;/plist:|:.+(Mach|scrip)/s/:[^:]+//p ' '/root/p' ' !/\/Contents\/.+\/Contents|Applic|Autom|Frameworks/&&/Lib.+\/Info.plist$/ { n++;print;} END { if(n<1100) print "/System/";} ' '/^\/usr\/lib\/.+dylib$/p' ' /Temp|emac/ { next;} /(etc|Preferences|Launch[AD].+)\// { sub(".(/private)?","");n++;print;} END { print "'${p[41]}'.plist\t'${p[42]}'";if(n<500) print "Launch";} ' ' /\/(Contents\/.+\/Contents|Frameworks)\/|\.wdgt\/.+\.([bw]|plu)/d;p;' 's/\/(Contents\/)?Info.plist$//;p' ' { gsub("^| |\n","\\|\\|kMDItem'${p[35]}'=");sub("^...."," ") };1 ' p '{print $3"\t"$1}' 's/\'$'\t''.+//p' 's/1/On/p' '/Prox.+: [^0]/p' '$2>'${p[43]}'{$2=$2-1;print}' ' BEGIN { i="'${p[26]}'";M1='${p[16]}';M2='${p[18]}';M3='${p[31]}';M4='${p[32]}';} !/^A/ { next;} /%/ { getline;if($5<M1) a="user "$2"%, system "$4"%";} /disk0/&&$4>M2 { b=$3" ops/s, "$4" blocks/s";} $2==i { if(c) { d=$3+$4+$5+$6;next;};if($4>M3||$6>M4) c=int($4/1024)" in, "int($6/1024)" out";} END { if(a) print "CPU: "a;if(b) print "I/O: "b;if(c) print "Net: "c" (KiB/s)";if(d) print "Net errors: "d" packets/s";} ' ' /r\[0\] /&&$NF!~/^1(0|72\.(1[6-9]|2[0-9]|3[0-1])|92\.168)\./ { print $NF;exit;} ' ' !/^T/ { printf "(static)";exit;} ' '/apsd|BKAg|OpenD/!s/:.+//p' ' (/k:/&&$3!~/(255\.){3}0/ )||(/v6:/&&$2!~/A/ ) ' ' $1~"lR"&&$2<='${p[25]}';$1~"li"&&$3!~"wpa2";' ' BEGIN { FS=":";} { n=split($3,a,".");sub(/_2[01].+/,"",$3);print $2" "$3" "a[n]" "$1;b=b$1;} END { if(b) print("\n\t* Code injection");} ' ' NR!=4{next} {$NF/=10240} '"`S0 27 14`" ' END { if($3~/[0-9]/)print$3;} ' ' BEGIN { L='${p[36]}';} !/^[[:space:]]*(#.*)?$/ { l++;if(l<=L) f=f"\n "$0;} END { F=FILENAME;if(!F) exit;if(!f) f="\n [N/A]";"file -b "F|getline T;if(T!~/^(AS.+ (En.+ )?text$|POSIX sh.+ text ex)/) F=F" ("T")";printf("\nContents of %s\n%s\n",F,f);if(l>L) printf("\n ...and %s more line(s)\n",l-L);} ' ' /^ +[NP].+ =/h;/^( +D.+[{]|[}])/{ g;s/.+= //p;};' 's/0/Off/p' ' END{print NR} ' ' /id: N|te: Y/{i++} END{print i} ' ' / / { print "'"${p[28]}"'";exit;};1;' '/ en/!s/\.//p' ' NR!=13{next};{sub(/[+-M]$/,"",$NF)};'"`S0 39 40`" ' $10~/$L/&&$9!~"localhost" { sub(/.+:/,"",$9);print $1": "$9;} ' '/^ +r/s/.+"(.+)".+/\1/p' 's/(.+\.wdgt)\/(Contents\/)?Info\.plist$/\1/p' 's/^.+\/(.+)\.wdgt$/\1/p' ' /l: /{ /DVD/d;s/.+: //;b0'$'\n'' };/s: /{ /V/d;s/^ */- /;H;};$b0'$'\n'' d;:0'$'\n'' x;/APPLE [^:]+$/d;p;' ' /^find: /d;p;' );c1=(system_profiler pmset\ -g nvram fdesetup find syslog df vm_stat sar ps sudo\ crontab sudo\ iotop top pkgutil 'PlistBuddy 2>&1 -c "Print' whoami cksum kextstat launchctl sudo\ launchctl crontab 'sudo defaults read' stat lsbom mdfind ' for i in ${p[24]};do ${c1[18]} ${c2[27]} $i;done;' defaults\ read scutil sudo\ dtrace sudo\ profiles sed\ -En awk /S*/*/P*/*/*/C*/*/airport networksetup mdutil sudo\ lsof test );c2=(com.apple.loginwindow\ LoginHook '" /L*/P*/loginw*' '" L*/P*/*loginit*' 'L*/Ca*/com.ap*.Saf*/E*/* -d 1 -name In*t -exec '"${c1[14]}"' :CFBundleDisplayName" {} \;|sort|uniq' '~ $TMPDIR.. \( -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 $' '.??* -path .Trash -prune -o -type d -name *.app -print -prune' :${p[35]}\" :Label\" '{/,}L*/{Con,Pref}* -type f ! -size 0 -name *.plist -exec plutil -s {} \;' "-f'%N: %l' Desktop L*/Keyc*" therm sysload boot-args status " -F '\$Time \$Message' -k Sender kernel -k Message Req 'bad |Beac|caug|dead[^bl]|FAIL|fail|GPU |hfs: Ru|inval|jnl:|last value [1-9]|n Cause: -|NVDA$|pagin|proc: t|Roamed|rror|ssert|Thrott|tim(ed? ?|ing )o|WARN' -k Message Rne 'Goog|ksadm|SMC:' -o -k Sender fseventsd -k Message Req 'SL' " '-du -n DEV -n EDEV 1 10' 'acrx -o comm,ruid,%cpu' '-t1 10 1' '-f -pfc /var/db/r*/com.apple.*.{BS,Bas,Es,J,OSXU,Rem,up}*.bom' '{/,}L*/Lo*/Diag* -type f -regex .\*[cgh] ! -name *ag \( -exec grep -lq "^Thread c" {} \; -exec printf \* \; -o -true $ -execdir stat -f:%Sc:%N -t%F {} \;|sort -t: -k2 |tail -n'${p[38]} '-L {/{S*/,},}L*/Lau* -type f' '-L /{S*/,}L*/StartupItems -type f -exec file {} +' '-L /S*/L*/{C*/Sec*A,E}* {/,}L*/{A*d,Ca*/*/Ex,Compon,Ex,In,iTu,Keyb,Mail/B,P*P,Qu*T,Scripti,Sec,Servi,Spo,Widg}* -type f -name Info.plist' '/usr/lib -type f -name *.dylib' `awk "${s[31]}"<<<${p[23]}` "/e*/{auto,{cron,fs}tab,hosts,{[lp],sy}*.conf,pam.d/*,ssh{,d}_config,*.local} {,/usr/local}/etc/periodic/*/* /L*/P*{,/*}/com.a*.{Bo,sec*.ap}*t /S*/L*/Lau*/*t .launchd.conf" list getenv /Library/Preferences/com.apple.alf\ globalstate --proxy '-n get default' -I --dns -getdnsservers\ "${p[N5]}" -getinfo\ "${p[N5]}" -P -m\ / '' -n1 '-R -l1 -n1 -o prt -stats command,uid,prt' '--regexp --only-files --files com.apple.pkg.*|sort|uniq' -kl -l -s\ / '-R -l1 -n1 -o mem -stats command,uid,mem' -i4TCP:0-1023 com.apple.dashboard\ layer-gadgets '-d /L*/Mana*/$USER&&echo On' '-app Safari WebKitDNSPrefetchingEnabled' );N1=${#c2[@]};for j in {0..9};do c2[N1+j]=SP${p[j]}DataType;done;N2=${#c2[@]};for j in 0 1;do c2[N2+j]="-n ' syscall::'${p[33+j]}':return { @out[execname,uid]=sum(arg0) } tick-10sec { trunc(@out,1);exit(0);} '";done;l=(Restricted\ files Hidden\ apps 'Elapsed time (s)' POST Battery Safari\ extensions Bad\ plists 'High file counts' User Heat System\ load boot\ args FileVault Diagnostic\ reports Log 'Free space (MiB)' 'Swap (MiB)' Activity 'CPU per process' Login\ hook 'I/O per process' Mach\ ports kexts Daemons Agents launchd Startup\ items Admin\ access Root\ access Bundles dylibs Apps Font\ issues Inserted\ dylibs Firewall Proxies DNS TCP/IP Wi-Fi Profiles Root\ crontab User\ crontab 'Global login items' 'User login items' Spotlight Memory Listeners Widgets Parental\ Controls Prefetching SATA );N3=${#l[@]};for i in 0 1 2;do l[N3+i]=${p[5+i]};done;N4=${#l[@]};for j in 0 1;do l[N4+j]="Current ${p[29+j]}stream data";done;A0() { id -G|grep -qw 80;v[1]=$?;((v[1]==0))&&sudo true;v[2]=$?;v[3]=`date +%s`;clear >&-;date '+Start time: %T %D%n';};for i in 0 1;do eval ' A'$((1+i))'() { v=` eval "${c1[$1]} ${c2[$2]}"|'${c1[30+i]}' "${s[$3]}" `;[[ "$v" ]];};A'$((3+i))'() { v=` while read i;do [[ "$i" ]]&&eval "${c1[$1]} ${c2[$2]}" \"$i\"|'${c1[30+i]}' "${s[$3]}";done<<<"${v[$4]}" `;[[ "$v" ]];};A'$((5+i))'() { v=` while read i;do '${c1[30+i]}' "${s[$1]}" "$i";done<<<"${v[$2]}" `;[[ "$v" ]];};';done;A7(){ v=$((`date +%s`-v[3]));};B2(){ v[$1]="$v";};for i in 0 1;do eval ' B'$i'() { v=;((v['$((i+1))']==0))||{ v=No;false;};};B'$((3+i))'() { v[$2]=`'${c1[30+i]}' "${s[$3]}"<<<"${v[$1]}"`;} ';done;B5(){ v[$1]="${v[$1]}"$'\n'"${v[$2]}";};B6() { v=` paste -d: <(printf "${v[$1]}") <(printf "${v[$2]}")|awk -F: ' {printf("'"${f[$3]}"'",$1,$2)} ' `;};B7(){ v=`grep -Fv "${v[$1]}"<<<"$v"`;};C0(){ [[ "$v" ]]&&echo "$v";};C1() { [[ "$v" ]]&&printf "${f[$1]}" "${l[$2]}" "$v";};C2() { v=`echo $v`;[[ "$v" != 0 ]]&&C1 0 $1;};C3() { v=`sed -E "$s"<<<"$v"`&&C1 1 $1;};for i in 1 2;do for j in 2 3;do eval D$i$j'(){ A'$i' $1 $2 $3; C'$j' $4;};';done;done;{ A0;A2 0 $((N1+1)) 2;C0;A1 0 $N1 1;C0;B0;C2 27;B0&&! B1&&C2 28;D12 15 37 25 8;A1 0 $((N1+2)) 3;C0;D13 0 $((N1+3)) 4 3;D23 0 $((N1+4)) 5 4;D13 0 $((N1+9)) 59 50;for i in 0 1 2;do D13 0 $((N1+5+i)) 6 $((N3+i));done;D13 1 10 7 9;D13 1 11 8 10;D22 2 12 9 11;D12 3 13 10 12;D23 4 19 44 13;D23 5 14 12 14;D22 6 36 13 15;D22 7 37 14 16;D23 8 15 38 17;D22 9 16 16 18;B1&&{ D22 11 17 17 20;for i in 0 1;do D22 28 $((N2+i)) 45 $((N4+i));done;};D22 12 44 54 45;D22 12 39 15 21;A1 13 40 18;B2 4;B3 4 0 19;A3 14 6 32 0;B4 0 5 11;A1 17 41 20;B7 5;C3 22;B4 4 6 21;A3 14 7 32 6;B4 0 7 11;B3 4 0 22;A3 14 6 32 0;B4 0 8 11;B5 7 8;B1&&{ A2 19 26 23;B7 7;C3 23;};A2 18 26 23;B7 7;C3 24;A2 4 20 21;B7 6;B2 9;A4 14 7 52 9;B2 10;B6 9 10 4;C3 25;D13 4 21 24 26;B4 4 12 26;B3 4 13 27;A1 4 22 29;B7 12;B2 14;A4 14 6 52 14;B2 15;B6 14 15 4;B3 0 0 30;C3 29;A1 4 23 27;B7 13;C3 30;D13 24 24 32 31;D13 25 37 32 33;A2 23 18 28;B2 16;A2 16 25 33;B7 16;B3 0 0 34;B2 21;A6 47 21&&C0;B1&&{ D13 21 0 32 19;D13 10 42 32 40;D22 29 35 46 39;};D13 14 1 48 42;D12 34 43 53 44;D22 0 $((N1+8)) 51 32;D13 4 8 41 6;D12 26 28 35 34;D13 27 29 36 35;A2 27 32 39&&{ B2 19;A2 33 33 40;B2 20;B6 19 20 3;};C2 36;D23 33 34 42 37;B1&&D23 35 45 55 46;D23 32 31 43 38;D12 36 47 32 48;D13 20 42 32 41;D13 14 2 48 43;D13 4 5 32 1;D13 4 3 60 5;D12 26 48 49 49;B3 4 22 57;A1 26 46 56;B7 22;B3 0 0 58;C3 47;D22 4 4 50 0;D23 22 9 37 7;A7;C2 2;} 2>/dev/null|pbcopy;exit 2>&-
Copy the selected text to the Clipboard by pressing the key combination command-C.
7. Launch the built-in Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Click anywhere in the Terminal window and paste by pressing command-V. The text you pasted should vanish immediately. If it doesn't, press the return key.
8. If you see an error message in the Terminal window such as "Syntax error" or "Event not found," enter
exec bash
and press return. Then paste the script again.
9. If you're logged in as an administrator, you'll be prompted for your login password. Nothing will be displayed when you type it. You will not see the usual dots in place of typed characters. Make sure caps lock is off. Type carefully and then press return. You may get a one-time warning to be careful. If you make three failed attempts to enter the password, the test will run anyway, but it will produce less information. In most cases, the difference is not important. If you don't know the password, or if you prefer not to enter it, press the key combination control-C or just press return three times at the password prompt. Again, the script will still run.
If you're not logged in as an administrator, you won't be prompted for a password. The test will still run. It just won't do anything that requires administrator privileges.
10. The test may take a few minutes to run, depending on how many files you have and the speed of the computer. A computer that's abnormally slow may take longer to run the test. While it's running, there will be nothing in the Terminal window and no indication of progress. Wait for the line
[Process completed]
to appear. If you don't see it within half an hour or so, the test probably won't complete in a reasonable time. In that case, close the Terminal window and report the results. No harm will be done.
11. When the test is complete, quit Terminal. The results will have been copied to the Clipboard automatically. They are not shown in the Terminal window. Please don't copy anything from there. All you have to do is start a reply to this comment and then paste by pressing command-V again.
At the top of the results, there will be a line that begins with the words "Start Time." If you don't see that, but instead see a mass of gibberish, you didn't wait for the "Process completed" message to appear in the Terminal window. Please wait for it and try again.
If any private information, such as your name or email address, appears in the results, anonymize it before posting. Usually that won't be necessary.
12. When you post the results, you might see an error message on the web page: "You have included content in your post that is not permitted," or "You are not authorized to post." That's a bug in the forum software. Please post the test results on Pastebin, then post a link here to the page you created.
Note: This is a public forum, and others may give you advice based on the results of the test. They speak only for themselves, and I don't necessarily agree with them.
Copyright © 2014 by Linc Davis. As the sole author of this work, I reserve all rights to it except as provided in the Use Agreement for the Apple Support Communities website ("ASC"). Readers of ASC may copy it for their own personal use. Neither the whole nor any part may be redistributed.

SFv120 - tip /dev/ttya into it produces output, but can't type

Hi,
This sounds elementary but I can't figure it out and the brain isn't functioning well at 1:20am.
I've got a v120 that did not have a console on it, so I connected a cable from a v880's serial to the serial A/LOM port on the v120.
I'm getting text displayed when I tip to it (tip -9600 /dev/ttya) but I cannot type.
Connecting the serial cable to serial B produces no output.
Thoughts?
Thanks.

Figured it out, it was a bad LOM card in the v120.
After I reset, I could use #. to get out of the console back into the LOM command line.

Timeouts and connection problems after 5.1(2) upgrade

AIM/chat and some other programs are having timeout/connection problems after upgrade to 5.1(2). I am using S241 also. The connection problems stopped when the IPS was set to bypass. Rebuilt IPS and left sigs at default settings and problem is still happening. I am not seeing any of the IPs that are having the problem in the Event Viewer or on the Events in the IDM.
Any known issues with the 5.1(2) that would cause this type of problem?

I don't know specifically, but I did notice that 5.1(3) was released today.

Hi, i am having trouble with my mac mail account, i cannot send or receive any emails because of the server connection problems. Message says it could not be connected to SMTP server. Thanks in advance for your help.

Hi, i am having trouble with my mac mail account, i cannot send or receive any emails because of the server connection problems. Message says it could not be connected to SMTP server. Thanks in advance for your help.

Hello Sue,
I have an iPad 3, iPad Mini and iPhone 5S and they are all sluggish on capitalisation using shift keys. I hope that Apple will solve the problem because it is driving me crazy.
I find using a Microsoft Surface and Windows 8 phone, which I also have, work as well as all the ios devices before the ios 7 upgrade.
It has something to do with the length of time that you need to hold the shift key down. The shift key needs to be held longer than the letter key for the capitalisation to work. For some reason, this is a major change in the way we have learnt to touch type on computers. I am having to relearn how to type!
Michael

RFC Receiver adpater Connection problem , Help us to solve ?

Hi Friends ,
 Our scenarilo is Mail to RFC. It was running fine. In RFC Receiver adapter i have given Maximium connection property to 1 .
 While multiple set data passed to rfc will connection problem will come ?
 Most data not uploaded . I am getting the following error.
 If i set max connection to 5 . It is 5 times or more than that it is pusing the data .
 i am getting the following error while i set the Max connection to 1 . . Any other place i need to change configuration ?
 - Error: 2007-09-24 10:51:22 GMT-05:30: Message processed for interface YRFC_EXT_WARR: com.sap.aii.af.rfc.afcommunication.RfcAFWException: error while processing message to remote system:com.sap.aii.af.rfc.core.client.RfcClientException: resource error: could not get a client from JCO.Pool: com.sap.mw.jco.JCO$Exception: (106) JCO_ERROR_RESOURCE: Connection pool RfcClient[CC_EXTE_WAREN_2W_RFC_RECEIVER]e7fa21f86ec535e883636c0beffc0f0c is exhausted. The current pool size limit (max connections) is 1 connections.
 Please give the description . I have referred many likns . Help us to solve this problem .
Regards.,
V.Rangarajan
Message was edited by:
 ranga rajan

Hi,
Have a look at this.This will help you.
1.
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/f3f93ee7-0c01-0010-2593-d7c28b5377c2
2. https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/3103eb90-0201-0010-71af-be6f4a6f61d1
Regards,
Akshay Jamgaonkar.
Reward points if find useful.
Message was edited by:
 Akshay Jamgaonkar

Unending connectivity problems -- and Desktop Help...

I'm wasting so much time on connectivity problems that it's positively wearying. Prior to the installation of BT Infinity here in April, I had a low quality broadband service because of the length of the line from the exchange: if I could get a download speed of 1.2Mbps and an upload of a quarter of that, I was doing well.
BT advised that thanks to fibre optic, my Internet should run much faster. So we had Infinity installed. I'm registered with Speedtest.net so am able to see my performance record.
The average download speed is now aroun d 6Mbps and the average upload, more than that at 7Mbps. How an upload speed can consistently be faster than a download escapes me.
But I'm not familiar with the ways of Internet connectivity and try as a I might, can't get my head around it.
This desktop computer runs Vista OS. Vista was **bleep** when it came out and is renowned for its botched handling of Internet connections. So I'm not blaming BT for the literally unending connectivity problems that are occurring now, with line drops, speeds slowing to a crawl, and no guarantee that any connection will last. But it would be good to actually use BT software to help fathom out what's going wrong here, and today's typical morning which looks like this:
1) Boot up computer. Automatic connection to hub via Netgear USB wireless adapter. Hub is on ground floor of this 3-storey property but signal strength from hub is excellent, as confirmed by inSSIDer monitoring, currently showing 54 with no other networks anywhere near that figure.
2) Perhaps 5 minutes after connection established, it's then lost. 'Local Only' is displayed. This is, apparently, a known Vista problem. But Microsoft has issued a fix for it. I know this, because it took 100 hours of ploughin g the Net to find out that MS had finally admitted to one more Vista screw-up. I've used the Microsoft router "fix it" before and it didn't work ("failed to process") so uninstalled it and have DL'd it again now and run it. This time it says it has fixed everything.
3) Computer is re-booted to make the fix effective. Computer connects to Internet. Speedtest.net check yet again confirms that upload speed is faster than download speed.
4) Connection dies. So much for Microsoft Fix It.
5) Windows diagnostics reports that it can re-set the IP profile (or something.) I click yes. The re-set goes through. Connectivity is restored. 10 minutes later, connectivity is lost. Just a red X in the tray. No connection of any kind, not even that daft 'Local Connection' only alert.
6) Reboot. Yet again. BT Desktop Help was installed here and ran OK when we were using our Netgear DSG34 router. But since the change to the BT Hub, the BT program has never run at all. So-oo. . . It has been uninstalled. And then re-DL'd and re-installed. And though the installation has been completed, clicking on 'launch' has failed to launch anything. But anyway. An hour ago, in one of the brief periods today when the Internet connection was holding up, I Revo-ed out the earlier install, DL'd BT desktop Help and re-installed it. . . and I'm still at the same stage as always, with a Firefox browser page that's open and completely blank and has been for the past 30 minutes. The URL is:
file:///C:/Program%20Files/BT%20Broadband%20Desktop%20Help/btbb/Start.html
Repeated page re-loading gets nowhere. Malwarebytes PRO is turned OFF to prevent any possibility of blocking and the antivirus is termporaily SUSPENDED. This PC runs on Windows standard firewall but even turning that OFF doesn't get the page to load. Copying the address into Internet Explorer in case there's a Firefox problem merely results in Firefox being opened and the same blank page running there.
7) After all that. . . Connection lost yet again and this time, Windows cannot connect at all. It reports that the "wireless network security key is not correct". I happen to know that it is, because this is maybe the 20th time it has reported this in the past 10 days and every time I have to key in the "correct" key all over again. . . at which point Windows still says it isn't correct and cannot repair.
Turning off the computer completely, unplugging from the wall, holding in the power switch for a full minute to clear the circuits, traipsing up and dowen three flights of stairs to turn off the hub, then wait, then turn the power back onm again. . . Ah, wot fun times I'm having here with my particular versioin of Infinity (as in, an infinity of connectivcity problems.)
Summary: I seem to be being simultaneously hit with one issue after another.
I'm bewildered as to why ever since Infinity was installed here, my upload speed is generally faster than my download speed. I'm not happy with endless Internet connection failures though am thinking that Vista is playing a large part here with its "wrong security key" and unending 'Local Only / Limited Connection' failures. I do miss my Netgear router and the ability to access a fantastic help menu and re-boot directly from the desktop without having to keep going up and down three flights of sdtairs to do so (I haven't been able to find out how toe access the BT Hub remotely.)
Above all though: I'm really tired of repeatedly trying to run freshly downloaded and installed BT Desktop Help software but getting no further than a blank page because the program has stalled.
If anyone has any advice / suggestions, other than to buy a carrier pigeon, that'd be much appreciated.
Thanks.

Thanks again to John and gg30340. Here's an update:
1) BT Desktop Help removed completely from this computer. The uninstaller itself mopped up everything, which surprised me. But anyway.
2) Bt Home Hub manager set up and working. Had to input serial number and create new password. All of this sounds fairly easy and would be if one had the device near the desk. But the idiots who built this property shoved the BT master socket inside the garage next to the door. Our two home computers are on the third floor. To ensure the wireless signal strength is OK, the Hub and Infinity module/device/whatever it's called are on a high shelf. It's a major job to even reach the darn things, never mind read the labels seeing as how the BT Infinity engineer was good enough to tidy up the cabling and make a very tight connection to the wall socket.
3) I had hoped to be able to back up the Hub's settings, seeing as the software provides for Advanced Settings / System / Backup. But not on mine (Hub 3.0). All that System allows is choosing which internet clock to define the accurate time. Everything else in System is just a pattern of short lines as if trying to indicate that there's some text there but it's invisible.This is now my second encounter with BT software which, for whatever reason, isn't functioning as it should on this PC.
4) Hub reset to factory fresh, according to BT guide.
5) Reset appears to have achieved nothing apart from requiring the password to be popped in again. After reset, it wasn't even possible to connect to the hub manager. Internet connectivity was eventually established for all of 30 seconds and then, gone.
6) Computer was shut down and then booted anew. Internet connectivity is still. . . dreadful. One minute everything's fine and then, literally,. the next minute a webpage won't load. Even opening the Hub Manager has taken three attempts, i.e., disconnecting from the Internet, re-connecting, failing, and trying twice more until success. Yet all the time these failures are occurring, the tray icon is showing a steady, unwavering green icon for Local and Internet access -- despite the fact, there manifestly isn't any.
7) Speedtest. net tests are actually showing upload and download 'trajectories' going slower and slower and finally halting at some point on the arc, then after a period of up to 30 seconds, suddenly becoming animated again. Speed test results with broadband speed checker UK and Think Broadband's checker are so at variance with one another, and with Speedtest, net, that it seems all three are using different technologies in pursuit of the same thing. Either way, upload speeds continue to be much, much faster than download speeds, a state of affairs I certainly have never encountered before.
8) Speedtest net tests taken in the past 10 minutes, with one test following on from its predecessor, begin at 8.24 down/8.88 up, followed by 5.24 down / 6.40 up, followed by a mind-numbingly lonnnnng 0.62 down / 8.70 up -- in other words, a continuous yo-yoin g of Internet connectivity to the pooint that it actually might as well not even be here (I've had to make five attempts just to get on to this forum. . .)
9) BT Speedtest will necessitate disconnection of everything downstairs and all boxes being lugged up here. This is actually going to require uncoililng tied-off cabling and hanging off a stepladder to do so -- though I surely can't be the only person in Britain who doesn't have a nice, handy BT master socket in their study or lounge. That said though: until we switched to Infinity, we *never* experienced these kinds of horrendous connectivity problems and never had need to unplug the Netgear router downstairs and bring it upstairs to connect directly to tjhe desktop PC so BT's own test could be run.
I'll just have to get to work dismantling stuff tomorrow. However, I have to say that after a factory re-set which has changed nothing at all, I'm beginning to think there's a problem with the BT line itself (hence why I'm happy to follow the advice here, though less than happy at the prospect of the messing about involved.)
Thanks, you two, for your patient help, and also for clarifying the situation re the three signal paths being shown on inSSIDer. At least I know that's usual now! And now, hopefully, when I press 'Post', I won't be faced with an endlessly spinning Firefox circle culminating in what may well be, or seem to be, the 57,938th time today of seeing "Page Not Found". . .

PHP and MySQL Connection problem

I am trying to make a PHP MySQL on a remote server connection in Dreamwesaver CS3.
When I enter the information (host, user, password, etc.) and hit TEST, I get the following error message.
"Access Denied. The file may not exist, or there could be a permission problem. Make sure you have proper authorization on the server and the server is properly configured."
I know the user, password, etc. work, as I can access the MySQL database with other software.
I checked with my host and they say there are no permission problems on their end.
I have checked the settings on the Test Server page in Site Setup and everything looks correct and works there.
I have not seen this particular problem described in other forum postings (although there are a LOT of postings on this topic!).
Any help would be appreciated.

I thought my testing server was the remote server and is always on as far as I know. I don't know how to turn it on or off.
Is there some other testing server that I should be aware of?
Frank
Date: Wed, 3 Jun 2009 15:43:02 -0600
From: [email protected]
To: [email protected]
Subject: PHP and MySQL Connection problem
I know you are using remote, but is your testing server on? if not turn that on and see if that does it. it just happened to me working on remote server and could not get mysql conn to work, until I turn on my testing (developer server), then I was able to connect to mysql and the tables that I created in phpmyadmin remotly was downloaded.
>

TS1538 my ipad can not continue to download ios 6.1.2 because of connection problem and it is stuck in connect to itunes image, i cant open it anymore..what should i do? help plz

my ipad can not continue to download ios 6.1.2 because of connection problem and it is stuck in connect to itunes image, i cant open it anymore..what should i do? help plz

Connect to iTunes on the computer you usually Sync with and “ Restore “...
http://support.apple.com/kb/HT1414
If necessary Place the Device into Recovery mode...
http://support.apple.com/kb/ht4097
You may need to try this More than Once...
Be sure to Follow ALL the Steps...
But... if the Device has been Modified... this will Not necessarily work.

I am experiencing wireless connection problem on 4s after ios 8.1 upgrade. The wireless icon appears showing that it's connected but webpages do not load. I have checked my internet connection with other devices and seems to be alright. what to do?

Hi
I am experiencing wireless connection problem on 4s after ios 8.1 upgrade. The wireless icon appears showing that it's connected but webpages do not load. I have checked my internet connection with other devices and seems to be alright. what to do?
I have tried reseting the network settings and forgetting my wireless connection and re-connecting to it. I even backed up my phone on itunes and restored it, factory reseted it. Nothing seems to work.
Also after my upgrade to ios 8.1 my personal hotspot option under cellular data has disappeared.
Would you please help me out? I would really appreciate it.

Hi..
Restart your router then restart the iPhone to test.
If that doesn't help, try this support article > iOS: Troubleshooting Wi-Fi networks and connections

Network connection problems, please help!

I have had an iPod Touch (4th generation) for over a year now and it worked fine. Today, something went wrong with my network connection. One moment it says that I'm connected to a network, and a few seconds later it says I'm not connected... Then a few seconds later it's connected again. I have full wifi bars, and it does it throughout my whole house. The wifi symbol keeps going on and off. I tried turning my Verizon Westell Model 6100G Modem off and back on because this normally fixes my wifi connection problems. This didn't work. Then I tried turning my iPod off and back on. This didn't work. I tried turning the wifi off and back on. This didn't work. I tried forgetting my network and signing back in. This didn't work. I also tried resetting the network, and this didn't work either. I'm not having any connection problems with my laptop, it's working fine. It's only my iPod. I'm still able to use the wifi, but for a split second, it will not work. I'm not sure what else to do. It's very annoying! I'm going to see if it does this at other peoples houses with their wifi. Can any one tell me what's wrong and how I should fix it? My only theory is a broken antenna...Please help! Thanks!

I have two things you could try.
1. Plug your iPod into the host computer that which the network is based around because sometimes the network has trouble identifying a device if it has been a while since you plugged it into the computer.
2. Find some way to get your network information (IP address, Subnet Mask, Router, DNS numbers) from another device on the network (e.g. laptop). Then go to Settings > Wi-FI and find your router and tap the blue arrow to the right of the name and tap the tab that says "Static" and enter this information accordingly. Then exit back to the network names menu and re-enter your passcode for your network (assuming you have a passcode)

SAP Crystal Reports data source connection problem using sap business one

Hi,
I m facing a problem regarding: SAP Crystal Reports data source connection problem using sap business one
I am trying to create a Crystal report but when I try to configure a new connection it does not work.
I select Sap Business One data source and try to complete the information required to connection but it does not list my companies databases, what is the problem?
Our Current SAP related software details are as follows:
OS: Windows Server 2008
SAP B1 Version: SAP B1 9 (902001) Patch 9
SAP Crystal Report Version: 14.0.4.738 RTM
Database: MS SQL Server 2008 R2
I have also added some screenshots of the issues.
Please have a look and let me know if you have any questions or any further clarifications.
I m eagerly waiting for a quick and positive reply.

Hi,
There is problem with SAP Business One date source.
I had faced same problem, I used OLEDB Data-source, and it worked fine for me.
So, try to use OLEDB.
Regards,
Amrut Sabnis.

WiFi Internet connectivity problems after upgrade to 10.8.4

After upgrading to MacOS 10.8.4 I am facing regular interruptions to my WiFi internet connectivity. Periodically the internet connectivity is lost and the only way to fix the problem is to turn WiFi off and on again. This happens frequently when I am downloading files at using big bandwidth (more than 1.5-2 MB/s). If I use assist me on the Network preferences tab, it displays an ISP error when the connectivity is down, however I am certain that I do nota have any kind of ISP or router issue since at the same time I have WiFi internet connectivity from my iPad mini, iPhone 4S and Samsung Galaxy S3. Therefore it should be a 10.8.4 issue

Troubleshooting Wi-Fi issues in OS X
Wireless Connection Problems - Fix
Wireless Connection Problems - Fix (2)
Wireless Connection Problems - Fix (3)
Wireless Connection Problems - Fix (4)

Lumia 900 Cellular Connectivity problem (AT&T) aft...

I've had a Lumia 900 on AT&T for about 5 months and have not had any connection problems. However, after the Tango update (OS *.8779.*; Firmware: *.12223), when I take my phone into work (which has no cellular reception normally) for an extended time and then take it outside it will sporadically not reconnect to the cell tower. It will show no connection forever. If I turn airplane mode on then off or turn off and then on the data connection, which seemed to fix similar problems before, I still get no connection.
The only solution is to restart my phone. One time it kind of hung on restart. The other time the phone froze up when I was trying to turn on/off the data connection. Restarting brings the cellular connection back. (Almost as if whatever software is controlling the cellular connection is crashing).
*I also installed the beta Nokia Counters program after the update -so that may be the problem too?
Has anyone else experienced this before. Is it a Tango issue, or a common issue that coincidentally started for me after the update?

I am having a similar issues with Wifi & cellular connectivity Issues. In addition, am seeing that my Lumia 900's screen is turning black with no response from the power button or any other buttons (bottom buttons will be light though). I have to reset the phone by pressing volume power camera buttons. And one or two times today it had issues restarting cycling the Nokia logo, AT&T logo, then black screen about three to four times before it showed the Windows Phone logo to fully boot up.
Totally Disappointed.

My computer is running very slow, how can I tell if it is a internet connection problem or my computer?

I have a mac 10.5.8 and it has been very slow lately. I often get the rainbow wheel when using it and recently I have had to restart the computer alot because it seems to freeze. The only other open program besides Safari is the finder which i cant seems to ever shut off. I'm not sure if this is an interent connection problem or if my mac needs servicing.

Please begin using 25 Ways to Speed Up Your Mac you will almost certainly find the cause there. The first place I'd look though is how much RAM your system has, if you never upgraded it that could be the problem. Macs ship with a minimum amount of RAM so it's possible a simple RAM upgrade would help. Use the article though and methodically go through the suggestions.
You also may benefit by reading XLab's Spinning Beach Ball of Death article too.

/dev/ttya connection problem

Similar Messages

Maybe you are looking for