Device driver error msg at startup-get white screen w/audio during playback

PE10 has been working fine until today.
Upon startup I get an error message saying my display driver is incompatible.
I checked the driver in Windows 7-it says the driver is up to date and working fine.
When playing back a video clip I'm editing in PE10, I get a white screen in the playback area with the correct audio. When I pause the playback, the video image appears. Play = white playback screen.
I have
-checked the display driver
-rolled my computer back to an earlier restore point
-uninstalled and reinstalled PE10
-turned off my firewall
Any other suggestions to try?

What version of Premiere Pro? Include the minor version number (e.g., Premiere Pro CS5.5 with the 5.5.2 update).
Premiere Elements 10
Have you installed the recent updates? (If not, you should. They fix a lot of problems.)
none available
What operating system? This should include specific minor version numbers, like "Mac OSX v10.6.8"---not just "Mac".
Windows 7 AMD dual-core processor
AMD Radeon HD 6310 display driver
What kind(s) of source footage? When telling about your source footage, tell us about the codecs, not just the container types. For example, "H.264 in a .mov container", not just "QuickTime".
MVI files from camera -- all worked fine in PE10 until today - same files play fine in other players
If you are getting error message(s), what is the full text of the error message(s)?
What were you doing when the problem occurred?
Starting up PE10
Has this ever worked before?
Yes, always until today.
What other software are you running?
None
Do you have any third-party effects or codecs installed?
No
Tell us about your computer hardware. Be especially certain to tell us about third-party I/O hardware (e.g., AJA, Matrox, Blackmagic, MOTU).
I'm not techie and don't know what this means - I don't have anything mentioned in brackets
Are you using Mercury Playback Engine GPU Acceleration?
no
Does the problem only happen with your final output, with previews, or both?
Error message above happens during startup
PE10 now loads really slowly (5 minutes)
Playback in project gives white screen instead of video. Audio is fine.

Similar Messages

HT4623 I cannot install my ipod to my computer. Says something about the device driver. I did not get it new either and so have no info about it. And I have never used one before and have no friends who have either. Can someone help me?

I cannot install my ipod to my computer. Says something about the device driver. I did not get it new either and so have no info about it. And I have never used one before and have no friends who have either. Can someone help me?

See
iOS: Device not recognized in iTunes for Windows
- I would start with
Removing and Reinstalling iTunes, QuickTime, and other software components for Windows XP
or
Removing and reinstalling iTunes and other software components for Windows Vista, Windows 7, or Windows 8
However, after your remove the Apple software components also remove the iCloud Control Panel via Windows Programs and Features app in the Window Control Panel. Then reinstall all the Apple software components
- New cable and different USB port
- Run this and see if the results help with determine the cause
iTunes for Windows: Device Sync Tests
Also see:
iPod not recognised by windows iTunes
Troubleshooting issues with iTunes for Windows updates
- Try on another computer to help determine if computer or iPod problem

I can't open swf files for schoolwork. Installed VCL, Flip4Mac and Adobe flash and shockwave players. Can get white screen with connection erro message with adobe flash player. Help me!

i can't open swf files for schoolwork. Installed VCL, Flip4Mac and Adobe flash and shockwave players. Can get white screen with connection erro message with adobe flash player. Help me!

Apple dropped playback support for .swf formats in QuickTime almost ten years ago.
Adobe Flash Player is the only way to view them.

I am getting white screen of death on my Macbook Pro, can someone help please?

I am getting white screen of death on my Macbook Pro, can someone help please?

Intermittent or inconsistent situations as you describe are the most difficult to resolve. First step you should do is be certain that you have your data backed up. I suggest that you do this by creating a bootable clone using Carbon Copy Cloner. The advantage to this is that not only is it a backup but can immediately be used to run your MBP in the event of an internal HHD failure.
The article that I gave you to start your search contains a link to this article:
https://discussions.apple.com/docs/DOC-3353
Though lengthy, it can resolve most issues if you go through all of the sections. If you cannot achieve success, then an Apple store genius bar is the last option.
Ciao.

Why do I keep getting a "system overload" message during playback?

Why do I keep getting a "system overload" message during playback? Even when I have only a few tracks playing together, I keep overloading and it stops the playback.

Purchasing iCloud storage will not help your issue. Also, if you want to upgrade, do it via iTunes rather than OTA - it doesn't require as much available storage to do it that way.
To check to see what is taking up so much of your storage, go to Settings>General>Usage>Manage Storage, and you will see a list of the items on your device and the amount of storage they are taking up.
T-mobile's offer of the 64GB iPhone 6 to new or additional line customers has nothing to do with Apple. You need to take that up with T-mobile.
Cheers,
GB

Install Windows 7 USB Load Drive A required CD/DVD drive device driver error

I am trying to do a fresh install on a brand new laptop. I have downloaded a couple of Windows 7 iso images. I have used DiskPart to prepare my USB device and have used the Microsoft usb iso tool to put the Win7 iso image on to the USB device. I always seem
to get stuch after I click Install it quickly comes up with a problem.... Load Driver - A required CD/DVD drive device driver is missing. If you have a driver floppy disk, CD, DVD, or USB flash drive, please insert it now... I am installing from a USB drive
so why does Windows require a CD/DVD driver? How do I get Windows 7 to install?
I have read other forums were people have put it down to a corrupt download but I have tried with a couple of different downloads and same problem everytime!
Please help!
Thanks
Gavin

Hi,
This error message appears if the disk controller mode is incompatible during setup. And it can be caused by your CD/DVD drive may be incompatible with Microsoft’s AHCI driver. To work around this
issue, please go to BIOS and disable AHCI mode for your disk controller. You can change the AHCI mode to IDE or ATA mode instead.
It may also occur if the media is corrupted. Please visit the following link to rebuild the bootable USB stick for Windows Server 2008 R2:
Building a bootable USB stick for Windows 7/Windows Server 2008
R2
And please check the USB disk: put the USB disk in other machines and boot to see if it works.
Please make sure that the download files are not corrupted.
Regards,
Sabrina
TechNet Subscriber Support
If you are
TechNet Subscription user and have any feedback on our support quality, please send your feedback
here.
Sabrina
TechNet Community Support

Startup disk white screen

My start up disk is full...I can't even get to my desktop to delete ant files and free up some space b/c my screen is white. I've read some other questions about full start up disks but none seem to discuss the blank white screen. I've pressed Command R when I booted up to get to the disk utility but I'm not sure if that's the direction I need to go. Any help would be appreciated..tks

If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.

Weird startup problems - white screen - USB/Firewire?

Not even sure where to start on this one...
I've got an Intel Dual 2.0ghz 20" Imac. 3 gb of RAM. I have AppleCare, but not sure this isn't peripheral related, so don't want to start down that path just yet.
I've got two Western Digital MyBook drives: a 250gb connected through the firewire 400 port, and a 500gb drive connected to the 800 port. An Eyetv 200 DVR is connected between the 250gb drive and the computer. Multiple USB devices (Treo 680, CanoScan LiDE500f, Epson Stylus Photo R220, Ipod) through an externally powered Belkin 7 port hub. Bluetooth keyboard and mouse.
About once out of every 10 boots, the machine only comes to a white screen. I have discovered that I have to disconnect all cables from the back of the machine to continue the booting process. Sometimes the boot continues when the firewire plugs are removed, sometimes with the USB. I also have the issue, documented elsewhere, with the WD drives intermittently unmounting.
I've had other, possibly related, issues with Missing Sync hanging (whether syncing with the Treo or not). Curiously, when this problem manifests, Console also hangs in the same manner. Not sure what clears the problem, but after a few reboots, logouts, and resetting the power manager, it generally goes away.
My hunch is that the USB/Firewire buses are underpowered or overstressed. The problems have so far resisted my trying to narrow them down further.
Another oddity: After problems booting, the display brightness is often reset to its lowest (dimmest) setting.
The most frustrating part of all this is that I use my EyeTV device to record TV programs when I'm away. Obviously, if the machine doesn't boot consistently, I can't depend on this.
Anyone have any better hunches?
thanks!

Perhaps I'm on the path to finding the cause of this problem. I took your advice, and using a Firewire 400 cable, connected the 500gb drive in line with the other Firewire devices. After rebooting, I immediately had the same interrupted startup process.
I noticed when connecting the 500gb drive, that it also has a USB port. I have now taken this drive out of the Firewire chain and connected it via USB. I haven't tested very long, but so far so good. I'm beginning to think that the Firewire bus on my 500gb WD drive is bad. I already knew that the 800 port didn't work. Lets hope the USB works. This is solely a backup drive, so USB is fine (unless I need to boot off a backup, in which case I know that the FW 400 will work in a pinch). I'll keep you updated.

I get white screen with logo after update OS 10.6.6

Yesterday I download the update, get the message intall and turn off so I did it.
Today i turn on the imac and it wont start, i get the white screen with the logo. I´ve triied almost everything...
Change disc permissions
Veryfy disc
Restart on safe mode
Turn on and off
Please help!

Try booting from your install disc again. Make sure that error was corrected.
Insert your install disk and Restart, holding down the "C" key until grey Apple appears.
Go to Installer menu and launch Disk Utility.
(In Mac OS X 10.4 or later, you must select your language first from the installer menu)
Select your HDD (manufacturer ID) in the left panel.
Select First Aid in the Main panel.
(Check S.M.A.R.T Status of HDD at the bottom of right panel. It should say: Verified)
Click Repair Disk on the bottom right.
If DU reports disk does not need repairs quit DU and restart.
If DU reports errors Repair again and again until DU reports disk is repaired.
When you are finished with DU, from the Menu Bar, select Utilities/Startup Manager.
Select your startup disk and click Restart
While you have the Disk Utility window open, look at the bottom of the window. Where you see Capacity and Available. Make sure there is always 15% free space.

After installing IOS8.02 my ipad air will not boot up. get white screen and apple logo and then a blue screen. over and over again.

Ipad air wifi only 16gb worked ok with IOS 8.0 . just did upgrade to 8.02 and now it will not boot up. I get a white screen with the apple logo and then a blue screen. it does this over and over. I need help. What do i need to do. Please help.

Hi ..
Reset the device:
Press and hold the Sleep/Wake button and the Home button together for at least ten seconds, until the Apple logo appears.
If that doesn't help, restore the iPad > Back up and restore your iOS device with iCloud or iTunes

Getting white screen when booting with alt key

Hi, I've installed windows 7 with boot camp on my brand new iMac 27" on OS X Lion.
Everything works fine when I configure boot camp to start as mac, or as windows.
However If I press the alt key when booting, as per this tutorial http://labnol.blogspot.com/2006/04/boot-camp-tutorial-install-windows-xp.html I get a white screen and that's it. Any Idea as to what might be the problem?

Hi
Try resetting the Parameter RAM (PRAM) - pronounced peeram. Restart the mac and depress the P, R, alt and command keys simultaneously. You should hear the boot chime. Keep the keys depressed until you hear the boot chime three more times. Release the keys thereafter.
Other possibilities are: you're filling up the hard drive and you need to clear some space; a problem is developing with the hard drive and/or directory structure. You need to run a disk repair utility such as fsck, DU's Repair Disk coupled with Repairing Privileges or something 3rd-Party such as Disk Warrior.
Tony

21" iMac getting white screen and does not boot up

Hi All!
This is my first time to post here but have been using Mac OS since 2009.
I am having issues with my Mid 2011 iMac 21". I keep getting a white screen and it does not boot up.
I am a bit technical so I have done all the necessary steps as below:
1. Powercycle the system (Shutdown, unplug for 10 seconds and replug) = No go
2. Reset NVRAM several times = No go
3. Went to Safe Boot = Vertical white stripes on blue screen appears
4. Tried booting on Recovery Disk = Vertical white stripes on blue screen appears
I'm thinking my video card is faulty now.
Any help guys? I hope my hard drive is not fried
What's worse, my 3 year extended warranty just expired last June and it's only been 3 months

First i can't send it back becuase it didnt have a warranty i purchased it on ebay. second the guy didnt send the install disks with it as he promised i have tried to follow up with him with no luck so hes been reported to ebay. and due to current buisiness expenses cant afford the new software. is there anything else i can do to at least boot the thing so i can figure out whats wrong with it. and has anybody experienced this before and if so how was the issue resolved. soooo frustrated as buisiness is at a stand still till this machine works. p.s.it has osx leopard latest version.
Message was edited by: AMILLIANZE

What driver is making all clips be "white screen"?

I'm using Premiere Pro CC on Windows 7. I previously was able to import and edit clips via exactly the same workflow - but now, not matter what clips I import, they all appear as the 'white screen'. The thumbnail is a frame of the video, but as soon as I mouse over, scrub, or try to play the clip, it turns totally white. Audio will play fine though.
I'm almost positive it has to do with using an AOC display that plugs in via USB. This is based on a similar issue I had using that display on a Mac and having part of a Blackmagic Design software UI not appear while using that screen.
I've tried lots of things, including updating the driver for my graphics card, from the manufacturer's site. Does anyone know of something else I can try - especially a way to undo whatever was done when I plugged in that USB display (worked without manually installing any drivers).
Please help. I needed to finish this project this morning
Thanks so much!
-dan

Hi Kevin. Yes, in both the Source pane and Timeline/Program, even a .jpg file shows up as just white.
To add to the case for my clips not being the problem, I've tried with every version I captured of this shoot:
Program out to SSD-based capture device, capturing as ProRes HQ (.mov)
Internal recordings on camcorder, as its top quality AVCHD (.MTS)
Locally encoded copy of web stream from CDN's stream encoding app (.mp4)
CDN's server-side capture of stream (.mp4)
USB Program Out encoded capture from video switcher (.mp4)
Each of those clips imports with a correct thumbnail image, but when scrubbed over or played, it's all white all the time (while audio is played correctly, as intended). Again, even the .jpg image has a proper thumbnail, but is showing as all white in all the contexts where the video clips are showing as white.
Is my best bet to just do a comprehensive extra local backup, reinstall windows, reinstall all software, restore data - and then start again fresh? Or are there other less time-consuming and less drastic measures I can try?
I'm really grateful to all who have (or will) offererd help on this. I know you've got your own work to worry about, and it's a real blessing for me.
-dan

IPhone 3G After turned on i get white screen

When I turn on my iPhone I get a white screen. The apple shows but when the lock screen should show that's when I get a white screen. I have tried the home power holding thing does not work. Please help

Reset the device:
Press and hold the Sleep/Wake button and the Home button together for at least ten seconds, until the Apple logo appears.
If that doesn't help, restore the iPhone > iTunes: Restoring iOS software

Turned on iMac, I get white screen

Turning on my Mac and after the initial apple logo goes away, it looks like the screen start to change, and goes to another white screen. I can see my mouse arrow, but nothing else. What happened, and how can I fix it?

Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you turn on the computer, and again when you log in.
Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal startup may also be somewhat slow.
The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of the test.

Device driver error msg at startup-get white screen w/audio during playback

Similar Messages

Maybe you are looking for