Device, driver loaded properly. Can hear through device 'phone input. Cannot hear through Logic Pro.

I successfully loaded the driver to my brand-new Steinberg UR22 interface. The device shows up in Preferences > Audio as the input and output. I can hear a signal through headphones plugged into the headphone jack on the Steinberg.
I cannot hear anything in Logic Pro, however. I've created a track, but cannot get my guitar to generate any movement on the LED fader on the lower left, or change rigs using the guitar amps/effects library on the right.
What am I doing wrong?
Why isn't there anything in the user's manual related to this?

You've created an Audio Track, correct?
Have you set the audio track to the correct input?
The UR22's second (#2) input should be used with the Hi-Z switch enabled.
Input gain at 1/2 also make sure the Master Output is up.
You have a monitoring knob labeled Input/DAW
If you wish to monitor both set the know to the halfway point, balance from that point.
By Master Output I was referring to the Output level on the UR22
Message was edited by: Pancenter

Similar Messages

Why am I hearing a clicking noise in my headphones? I'm on the iMac and I'm going through logic pro x. i have a focusrite scarlett 2i2 and my mic is a blue spark. is it my presets? i just want the clicking/popping noise to go away

why am I hearing a clicking noise in my headphones? I'm on the iMac and I'm going through logic pro x. i have a focusrite scarlett 2i2 and my mic is a blue spark. is it my presets? i just want the clicking/popping noise to go away

Hi,
Sorry to hear you are experiencing problems with you device.
Please raise a case with our Customer Support team and we will do everything we can to help:
http://global.focusrite.com/answerbase/contact
We look forward to hearing from you.
Best regards,
Luke
Focusrite Technical Support UK

My iphone can't load facebook "news feed" when connect wifi but when connect 3G it load normal . can't connect all phone . pleas help me

My iphone can't load facebook "news feed" when connect wifi but when connect 3G it load normal . can't connect all phone . pleas help me

Hi, Shadiamond Murray.
Thank you for visiting Apple Support Communities.
Sometimes a simple power cycle of the router can correct the issue that you are experiencing. However, the issue could be a little more complex. Wi-Fi routers need adjustments to settings periodically for optimized performance with the constant progression of wireless device technology. Below, I have included two articles. The first article will cover basic Wi-Fi troubleshooting regarding iOS device connection. The second article cover the recommended settings for current Wi-Fi access points.
iOS: Troubleshooting Wi-Fi networks and connections
http://support.apple.com/kb/ts1398
iOS and OS X: Recommended settings for Wi-Fi routers and access points
http://support.apple.com/kb/ht4199
Cheers,
Jason H.

Hi, I need to sync my phone to our home laptop. Phone was synced to a Mac that I no longer have access to. Can I sync my phone to the home laptop (MacBook Pro) and not lose all of my photos and contacts??

Hi, I need to sync my phone to our home laptop. Phone was synced to a Mac that I no longer have access to. Can I sync my phone to the home laptop (MacBook Pro) and not lose all of my photos and contacts??

Hi Michela27,
Thanks for visiting Apple Support Communities.
If you have content on your iPhone that isn't on your computer, the best thing is to use the advice in this article to transfer it to your new computer before setting up sync:
iTunes: Transferring media from your iPhone, iPad, iPod touch, or iPod
http://support.apple.com/kb/HT1209
Cheers,
Jeremy

Does anyone know where you can buy an "AZERTY" keyboard or keyboard cover for Logic Pro X?

Does anyone know where you can buy an "AZERTY" keyboard or keyboard cover for Logic Pro X?
Thanks for the support.

KB covers makes a logic covers and azerty covers. Why not give them a call to see if they can make one for you?
x

Recording Kontakt through Logic Pro x?

I want to record Kontakt 5 instruments through Logic Pro X, but the Setting and Instrument buttons are not showing in the Inspector. In all the tutorials that I have seen, you click the Instrument button in the Inspector and select Kontakt as you instrument. Is there a setting in Logic to show these buttons? I am using Kontakt 5 Player right now, do I have to have the full version for it to work? I used to do this with Garageband all the time. And also, I am a hardcore noob, so simple terms are much appreciated!!

hi i use a midi to usb cable from ebay then do this really easy
https://www.youtube.com/watch?v=f8o0cNw07YE

"recording what i can hear" in logic ??

Hi, i want to record what my computer is playing for sampling purposes. I can do this type of thing in sony acid it gives you a "record what you can hear" option but im quite new to logic 8 so im not sure if i can do that?!?!?
Thanks in advance guys
D

So I've read most of the getting started thing and it tells you all kinds of things about editing songs etc...but it doesn't seem to say anything about not being able to monitor the sounds yo are recording. Example when I click the record button and have a track record enables it shows the information being drawn on the arrange region area but I can't hear the notes I am writing with the keyboard while i am recording nor playing it back...but..I can hear the click track which tells me the monitors are recognizing the data sent from logic to the interface..so the underlining problem is basically how can I get the sound that is being written through my monitors? Did I assign something wrong in the start up assistant or what?

Can i install logic pro without the cd because my dvd driver of my mac doesn't work . i have the key for logic pro

can i install logic pro without cd ? , i have the key for the logic pro but my dvd driver of my mac doesnt work ?

Buy an external USB2 DVD/CD drive..... (Amazon's Basic model works great)
Or..
Borrow someone else's Mac that has a DVD drive fitted and use that via Remote Disk
Note:
There is no legal means of downloading available for Logic Pro 9.. unless you originally purchased it via the App Store..
Therefore, in your case, you must install from the DVDs you have...

Record with two usb devices at the same time on LOGIC PRO X

I would like to record both with my Samson USB mic and my guitar wich has also a USB input in the same time. How do i make that happen? Logic Pro X only sees one device whilst recording.

You need to create an aggregate device in OSX, and then select that as your audio device in Logic's options.
Then whatever you've set up as the inputs will be selectable within the logic audio buses.
Here's an official Apple article to get you on your way:-
http://support.apple.com/kb/HT3956
Any more questions please post back.

Can't sync Digi 002 as an interface for Logic Pro 7

I discovered Logic about a year after I had already purchased a Digi 002, and have been using it as my interface for Logic Express for about 6 months.  No problems.  I upgraded to Logic Pro 7 last month and now get only garbled sound and the following error message. "Error while trying to synchronize audio and midi.  Sample rate 88215 recognized.  Check conflict between Logic and External Device."
I am trying to run Logic Pro 7.  I still also use Pro Tools LE version 7.0 which runs fine.  I can play itunes songs, Garage Band, movies, Pro Tools songs, etc., no problem, but not Logic Pro, or Logic Express.
When I switch to Built In Audio, Logic Pro works fine through the tiny built in speaker, but trying to use the Digi 002 as my interface all the sound comes out garbled.
I have been pulling out my hair for weeks.  Any help would be much appreciated.

Tony P.M. wrote:
The digi people also recommended buying the update for 7.3 and then updating to 7.3.cs4.  I am going to give that a try.  What does Pro App Support 4.0 do and where do I find it if you think that might help me?
That is what I'm running, and it works great. Give it a shot. You can do a search on this forum, or on the Apple Support section of the website, and search for that term (Pro Application Support).
Yes I have learned my lesson with auto update.  Live and learn.
Yes. Remember, a DAW machine is NOt a regular computer you can do whatever with. Audio software and hardware are finicky creatures that don't play nice if you're messing with their operating system willy-nilly.
I spoke with the Apple Store people today as well.  They suggest I spend $100 and sign up for one on one support and bring the whole **** set up in to the store and let them work on it. Seeing as how I am using a G5 tower, and we are talking about a digi 002 board, that is going to be alot of fun to lug across the mall.   I am just about that desperate though.  Any thoughts on one on one support in store?
LOL!!! they just want your money, and will most defniintely screw up your system. They'll update wrong, install stuff you don't want, and re-configure your system to THEIR liking. Stay away from the genius Bar. When it comes to Pro audio, they really know little or nothing. As an example, I went to my local Apple store recently and asked for a copy of Logic Pro. the helpful guy there responded "Logic what? we don't have that kind of software here."
Thanks for the help.  Again.
You're welcome. Hopefully soon you'll have it up and running.
Cheers

Why does my guitar make crackling noises when it plays through logic pro/garageband?

When my guitar plays directly through the interface and montors, it sounds perfectly fine. But whenever I want to add effects through a musical application such as garageband or logic pro x, I get this weird, very loud crackling/bubbly sound. Can anyone help me out with this?

I have the exact same problem and it's been a week or so. It kind of just makes those weird noises out of nowhere and scares the **** out of me. Did you end up at the Apple Store or were you able to fix it up on your own?

Can't get any FX expansions to show in Logic pro x

I had BFD Eco and Arturia spark working on Logic 9 so I could use them as instruments. I had Avox toolkit working on FX expansion. I can't even find any of them on X. I deleted the audiocache file a while back and it isn't there to delete now. I have run Au manager several times. I've downloaded the latest legacy drivers, and looked at "get info" to find that one can't open X in 32 bit mode. I am out of ideas. I just upgraded to OS 10.8.4 as well.
Help???

..and can only run 64bit AU Plugins..... which is why you cannot see or use 32bit only AU Plugins.... in LPX
There are some workarounds... if there isn't a 64bit version of your plugin available...
The Pro End solution is to use VEP5 as a host.... for hosting 32bit AU plugins in LPX. You can also connect slave Macs (and PCs so you can run Windows VSTs within Logic) to your main Mac running Logic to spread the load of different plugins within your network... This is what I use here and couldn't live without these days...
http://www.viennaensemblepro.com
A cheaper alternative that is much less flexible... but works with some 32bit plugins is 32 Lives
http://www.soundradix.com/products/32-lives
There is also a 'free' method that might work for you.....
http://www.macprovideo.com/hub/logic-pro/how-to-run-32-bit-plug-ins-in-logic-pro -x

How can I open a fcp7 project in the new logic pro X?

How can I open a final cut pro 7 project in Logic Pro X?

What are you trying to achieve? FCP7 is a movie project format, not to mention it's years old while Logic is a music sequencer. If you try to add audio and soundtracks to a movie you'll need to export the movie file and add it as a video track (just drag and drop) to your Logic project. You may want to do your editing in Logic with a LoRes version of your movie, than export your work to a lossless audio format and put that file in your Final Cut for HiRes export. Logic Pro also supports region positions as SMPTE (e.g. in the event browser), if that helps you synchronize some events.

Can I use my old Garageband Jam Packs with Logic Pro X?

I'm in the process of moving all of my Logic X Library content to an external hard drive and it occurred to me that I still have 4 GarageBand Jam Packs that I might be able to use in Logic X. Does anyone know if there is any real difference in the loop content of the Jam Packs and the loops that are on Logic X ? Has anyone tried this and made any kind of comparison? Just wondering. Thanks.

When you download all the additional content from within Logic Pro X.. any jam packs you are missing are then installed during that process... but if you already have them all installed the LPX additional content installer will find them and set them up for use in LPX.
The content of the Jam packs are identical....

Can I use a VS-700C control surface with Logic Pro?

Hi,
Does anybody know if I can use a Roland VS-700C control surface and/or VS-700R audio interface with Logic Pro?
Cheers,
Craig

If it supports the Makie protocol, it might work... but I wouldn't purchase one on that basis without trying it first.

Device, driver loaded properly. Can hear through device 'phone input. Cannot hear through Logic Pro.

Similar Messages

Maybe you are looking for