Device Manager is not recognizing my robotic library

Win2k8 R2 server operating system with Adaptec 29320LPE SCSI adapter in a PCIe slot. Attached to Adaptec is a Quantum Superloader 3 robotic tape library. LUNS support is enabled in the Adapted BIOS. During POST Adaptec card shows two devices found: Quantum
DLT4 and the LUN1 tape library.
Device Manager only recognizes a single Tape Device: Quantum DLT 4. No "Medium Changer" device or "Robotic Library" device shows in Device Manager.
The Quantum Superloader works fine with my older Win2k3 Server. That server is using a PCI 64bit Adaptec card for the Superloader 3.
I could use some assistance on how to resolve this issue.

Hi,
As for this issue, you should check with the hardware vendor for the appropriate documentation for the device
and verify with hardware vendor whether it is compatible with windows server2008R2.
If it’s compatible with windows server2008R2, you should have appropriate driver software.
Best Regards,
Jeff Ren
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread.

Similar Messages

IPhone composition   The payload of   and mobile device management is not installable in a utility.

Hello.
You.
And thank you.
I want you to help me if you please.
I am not good at English.
The status code of 201,204 which Apache returns from a MDM server.
iPhone composition   The payload of   and mobile device management is not installable in a utility.
iPhone composition   Console of a utility.
May 1 09:46:15 unknown mc_mobile_tunnel[13281] <Notice>: (Note) MC: mc_mobile_tunnel shutting down.
May    1 09:46:18 unknown. profiled [13274] <Notice>:   (Note) MC:   Checking. for. MDM installation ... May 1 09:46:18 unknown profiled[13274] <Notice>: (Note) MC: ...finished checking for MDM installation.
May    1 09:46:18 unknown. profiled [13274] <Notice>:   (Note) MC:   Beginning. profile. installation ... May 1 09:46:20 unknown profiled[13274] <Notice>: (Error) MDM: Cannot Authenticate. Error: NSError:Desc     : Since a transaction with the server in "https://www.anetm.com/dav/chkin" was in the situation of "204", it failed.
US Desc:   A transaction with the server at"https://www.anetm.com/dav/chkin"has failed with the status"204."
Domain : MCHTTPTransactionErrorDomain
Code   : 23001
Type   : MCFatalError
Params : (
"https://www.anetm.com/dav/chkin",
204
May    1 09:46:20 unknown profiled [13274] <Notice>:   (Error) MC:   Cannot install MDM "mobile device management" .Error:   NSError:
Desc    :   A payload "mobile device management" was not able to be installed.
Sugg    :   Since a transaction with the server in "https://www.anetm.com/dav/chkin" was in the situation of "204", it failed.
US Desc:   The payload "mobile device management" could not be installed.
US Sugg:   A transaction with the server at"https://www.anetm.com/dav/chkin"has failed with the status"204."
Domain : MCInstallationErrorDomain
Code   : 4001
Type   : MCFatalError
Params : (
"\U30e2\U30d0\U30a4\U30eb\U30c7\U30d0\U30a4\U30b9\U7ba1\U7406"
...Underlying error:
NSError:
Desc    :   Since a transaction with the server in "https://www.anetm.com/dav/chkin" was in the situation of "204", it failed.
US Desc:   A transaction with the server at"https://www.anetm.com/dav/chkin"has failed with the status"204."
Domain : MCHTTPTransactionErrorDomain
Code   : 23001
Type   : MCFatalError
Params : (
"https://www.anetm.com/dav/chkin",
204
I would like to solve this problem.
If you please, please help me.

Hello Jack,
Thank you for providing the details about the Apple Mobile Device USB Driver is not being listed. I found an article with some additional steps you can take.
I recommend following the steps in the section titled "If the Apple Mobile Device USB Driver is not listed" in step 5 of the following article:
iOS: Device not recognized in iTunes for Windows
http://support.apple.com/kb/TS1538
Thank you for using Apple Support Communities.
Best,
Sheila M.

Anyone who has had a webcam failure where the "device manager does not recognize the hardware"?

HP Pavilion dv7 running win 7 64 bit
Device manager does not recognize trueVision HD webcam. Tried all the suggestions on HP website, which eventually says it's a hardware failure. Has anyone had any resolution to this issue? I see the problem occurs across various platforms with varying resolutions to the problem.

Ha Ha. I'm replying to my own post!
Solution.... If your laptop does not recognize the built-in camera at all in the device manager and your warranty has expired or your willing to void your warranty. You can see if you have the same problem as I had. Gently pry the plastic frame around your camera and display screen apart you need to go at least half way down the sides. There is also some adhesive tape you will need to push to one side or the other. To the right of the camera there is a very small connector, it wont even look as if it is separated. Use a tweezer or small screwdriver to push the connector into the socket. This fixed my problem ...The next startup recognized the camera and has worked perfectly since. In my opinion (13yrs experience in reliability engineering semiconductor manufacturing) this is a manufacturing reliability issue either the socket cannot hold the connector in place or there is too much strain on the wiring to the connector. Good luck.

Drive appears in device manager but not in My Computer

I just wanted to post a solution that took me about 2 hrs to solve. Issue was, my firewire WD TB drive would be seen, by XP (SP3) on boot camp, in xp's device manager but not in My Computer. My goal was to format this as an NTFS drive for my boot camp files. I was unable to format this in Leopard as ntfs either. I tried installing HD drivers and formatting from leopard as FAT32 (just so Windows would see it) but all failed.
The solution I used was as below. (this would not work if you want to retain data on the drive, I didn't care as I was setting up an old drive and reformatting from scratch). Solution:
- Download free 10-day trial of Paragon's NFTS for Mac.
- Install on Leopard (note app seems sparse after download as if it didn't work) but... then...
- Open Disk Utility, you'll notice more options under Erase>Format Options drop down. Paragon acts like a plugin it seems and gives Disk Utility NTFS format options. Don't erase yet...
- Go to Partition tab, Select 1 partition and the options and select Master Boot Record and partition. (Win XP didn't see my 2nd partition when I did this so maybe it can only see the one). Anyhow create 1 big MBR partition.
- Then, go back to erase if you want and zero out.
Drive should then appear when you restart in XP.
I reformatted here from xp too just to be sure that the drive would be fully xp compatible though not sure this would be necessary.
BTW - I also had a 120GB usb drive with the same issue. For some reason with this one I was able to simply erase as FAT32 from leopard without the Paragon plugin and it showed up in XP. Go figure.

Hi Simnap,
Unfortunately Windows XP can only read hard drives that are 2 TB's or less due to barriers set in place by the age of the operating system and the hardware of that time period, even if its still used now. So you may have to partition the drive into (2) 2 TB's or (4) 1 TB's in order for XP to see it. Mac OS X supports 4 TB and above, just not XP.
Kind Regards,
Sidney S. Ramirez

Western digital 3tb 2nd hard drive shows up in device manager but not in disk manger.

Internal wd 30eurs drive shows up in device manager but not disk manager. Any suggestions on how to format this drive and partition it. I am running windows 7 64bit os

Open the Windows Control Panel and then select Device Manager which allows you to initialize and format new hard drives installed in your system.
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread. ”

Zen V Plus recognized by device manager, but not by Media Explorer/Windows Media Pla

Hi,
I just got back from Best Buy after buying a Creative Zen V Plus. I installed everything from the CD and plugged in the player, but the Media Explorer doesn't recognize it (even after restarting PC). The Device Manager recognizes it but there's an exclamation mark next to it. The Windows Wizard came up numerous times asking me for permission to connect to the internet and install the driver for me, and after a while I tried doing so but it said it couldn't find anything (I would like to shave that wizard's beard off).
I went through all the stickies in the forum and about 3 different troubleshooting sessions with no luck. I googled it and asked this question on Ask Yahoo!, but no luck yet.
Here's my PC info:
Windows XP SP2
768MB Ram
Pentium 4 2.8Ghz
USB 2.0 (I tried different ports, the player does seem to be charging as there's a little lightning bolt flashing on top of the battery icon)
I'd really appreciate it if someone could help me out.
Thanks!

Ok. I checked my version of XP. It is XP Pro, Version 2002, SP2. I checked and already had the 2 hotfixes that were listed as being needed before proceeding. I followed all the steps and changed the registry key on "everyone" as the instructions stated to do. My ZVM is still not recognized by any of the software for transferring or organizing MP3's. My computer still recognizes that it is attached. It still gives me the device icon in the task bar. It still says it's A-ok in the Device Manager. It does everything, except it is not detected by ANY of my music software. <sigh>? Frustration is at its peak for me right now. I really appreciate all of the efforts. I'm at my wits end now. I have done everything you have indicated I should, but am getting the same results. I did purchase an extended warranty from Circuit City where I purchased this last summer. Is that the next step? Do I need to get this replaced?I love this player and really don't want to go through this again. We had to exchange it twice in the first month because it froze up and wouldn't do a thing. This last one has been perfect. I keep it in a leather padded case at all times. It never has the battery drained. It never gets jostled or bumped or dropped or anything that might damage it. When not being played, it stays on my desk in the case.
Thanks so much for any and all help.

HT1351 The DEVICES heading is not showing in my library column...help????

I am unable to sync my ipod with new songs that I have just downloaded because the "DEVICES" heading is NOT showing in the left hand column under the Library (where everything is listed while in itunes).
I have tried to call for help, but I was told I needed to pay a 19.99 fee for the tech support- which is rediculous in my opinion since I paid for the ipod, paid for the songs, paid for the laptop, shouldn't the tech support be included in there for free?
Anyway, my question IS....what happened to the DEVICES heading? How do i get it back? How am I to sync my music?
Thank You for any help that can be offered!

shouldn't the tech support be included in there for free?
It is for 90 days from the date you purchased your iPod, or for two years if you purchased the AppleCare extended coverage for it.
The "Devices" header will only appear if the iPod you're connecting is recognized, which apparently it is not. This may help:
http://support.apple.com/kb/TS1369
Regards.

The device manager does not appear in iTunes

Hello, Everyone:
Neither the Device Manager nor my iPhone 3G appears in iTunes. Has someone else experienced this problem?
Be well,
Bob

If you mean that your phone does not appear under Devices in iTunes, follow the troubleshooting steps here: iOS device not recognized in iTunes for Windows.

My internal webcam on HP EliteBook 8460w not detected in device manager and not detected by driver

Hello all...
I just bought HP EliteBook 8460w, after I installed all the program and driver I find out that the internal webcam is not working. When I have check in the device manager the webcam is not listed. Then I tried to download the newest software/driver of it, it appears a message box that mention the webcam is not detected, please enable it from the bios. Then I checked from the bios, the webcam is not listed to be enable. Afterward, I was wonder maybe the bios is not up to date. Then I updated the bios, but still after I checked, the webcam is still not listed to be enable.
So please if anyone have the same experience or might know some answer or solution for it, I would be very happy to try. Its starting to get on my nerve.
Thank you very much before....
Cheers,
Denmuh

Hi, I figured out how to get the camera working on my 8460w laptop. I am running Windows XP SP3. No guarantee this is what will fix yours, but here's what I did:
I installed these two drivers from the HP.COM site:
First -HP Universal Camera Driver
link: http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=32...
Second -HP High Definition (HD) Webcam Firmware
link: http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=32...
Control Panel - System - Harware - Device Manager
Under Imaging Devices category, look for an existing camera device line.
Uninstall this device.
Then after a few moments, Windows recognized the camera again and automatically installed it with the right drivers (since it is really just a device connected through an internal USB port).
Hope this helps you too.

Device Manager Can not recognise the Camera

From the first day I installed my iPhone the camera would not connect to my PC. In the device manager my camera comes up in Imaging devices as "iPhone" with an ! inside a yellow circle (Not Triangle)I have deleted the driver and reinstalled it several times, and it is as if it can not find the driver or it does not exist. I also deleted the USB "Apple Mobile Device USB Driver" and reinstalled it and rebooted several times. In the device manager I believe the device should come up under Imaging devices as "Apple iPhone" instead of just "iPhone".
iTunes syncs fine and I can even send photos to the iPhone to the photos app as an album, but I can not get the iPhone photos off the phone except via email
Does anybody know the solution to this problem?

Oh my gosh! I was having this problem, too! I found the solution, tho. It really worked!
I was having a pretty serious problem that started when I upgraded to iPhone 3.1. While iTunes recognized my iPhone, iPhoto didn't.
And if I opened iPhoto, I couldn't see the camera. Same with Image Capture - it said no device detected. I know there was no problem in 3.0.
Luckily, there are other ways to get the photos off the iPhone, and luckily iTunes recognizes the phone, but that of course is not the point.
Good news is that I believe I found the fix. Click through and I'll see if I can explain it.
For some reason, it has to do with photos saved to the camera roll that were not shot with the iPhone. In other words, photos saved from email or screenshots. I have no idea why that would be, but once I deleted the non-shot photos, iPhoto launched normally and all was right with the world.
The problem is mentioned several times in the Apple support forums and everyone with it is running iPhone 3.1 and Snow Leopard 10.6.1. Restoring the iPhone, rebooting and repairing permissions from the Snow Leopard disc has no effect. The only fix I've found is my weird one.
Anyone else seeing this problem? Anyone find a different fix? Please let me know in the comments or interact with me on Twitter or Facebook.
Thanks and thanks for calling.
http://www.chicagonow.com/blogs/iphone-therefore-iblog/2009/09/iphoto-doesnt-rec ognize-iphone.html

Webcam failure where the "device manager does not recognize the hardware"? Pavilion dv7 Win 7

I have done everything the website suggests. Nothing worked. Has anyone gotten satisfaction to the issue either by a fix or a service center repair? I have seen others with the same problem accross different operating systems.

Ha Ha. I'm replying to my own post!
Solution.... If your laptop does not recognize the built-in camera at all in the device manager and your warranty has expired or your willing to void your warranty. You can see if you have the same problem as I had. Gently pry the plastic frame around your camera and display screen apart you need to go at least half way down the sides. There is also some adhesive tape you will need to push to one side or the other. To the right of the camera there is a very small connector, it wont even look as if it is separated. Use a tweezer or small screwdriver to push the connector into the socket. This fixed my problem ...The next startup recognized the camera and has worked perfectly since. In my opinion (13yrs experience in reliability engineering semiconductor manufacturing) this is a manufacturing reliability issue either the socket cannot hold the connector in place or there is too much strain on the wiring to the connector. Good luck.

USB Device for IPOD not recognized by Windows, whether ipod connected or no

During the past few days I have received a pop up error message from (I would think) Windows that the USB device is not recognized. I have the USB plug for the ipod connected (as always)but the ipod isn't even connected. It keeps popping up like every few seconds that the usb device is not recognized.
When I attach the ipod itself, the ipod is recognizing it because it powers up. But, it took 10 times just to get the ipod to recognize through itunes. It updated, then immediately upon completion, windows again starting giving repeated error messages that the usb device wasn't recognized.
I have downloaded the newest itunes but I had it on my system for 4 days with no problems whatsoever. I don't think that's it. No other system changes.
I've deleted my temp files and cache. Also did a "disk clean up" and "defrag." It's still doing it.
Any suggestions?

I'm having the same problem. Ever since I upgraded to version 7, iTunes & my PC no longer recognise my iPod, and it therefore won't sync.
It's not the USB port (other devices work in it), I rebooted my iPod and re-installed iTunes, I've tried stopping and starting the iPod Service (but can't see my iPod in My Computer). When I run the Diagnostics it says iPod connection failed. I've even bought a new USB cable but that doesn't work either.
This is driving me up the wall. Is there a glitch with iTunes 7?
Can anyone help me out?? Thanks
Windows XP

Ipod 5th Generation 80 GB / Device Manager / Driver not Installed / Code 28

Well, where do I begin! Got my 1st Ipod 2 days ago & still unable to use it! I have installed & uninstalled the itunes 7 software numerous times. On phone w/ Apple for 1 hour...followed by online chat help w/ Dell.
I've tryed 4 different USB ports on my computer. The device Manager shows the Ipod w/ a ? and a ! in yellow. The add new hardware tells me, "Drivers for this device are not installed. Code 28." My computer reconizes that the ipod is plugged in, but will not do anything. There is no communication between the 2. Keeps telling me to insert cd for software for ipod.
Help! Does seem that other people are having similar issues. I think a software cd should of been provided w/ the ipod....not sure if that would of corrected my problem.

Hi,
Click Start > All Programs > Accessories > Run. the Run dialog appears,
Type %temp%, then click OK.
locate and enter into the HP Installation temporary folder, start with the 7Z characters.
If you can see several folders starting with 7Z, locate the latest one.
Click the Address bar area, then the full address path will appear,
Copy the full path location by clicking CTRL + P while the path is selected.
Enter the Device Manager.
Right click the printer name with the error mark, then click Update Driver.
Select the second option to manually locate the driver.
Paste the temporary folder path and click Next (Keep Include Sub Fulders marked), the driver should be updated.
Please let me know of any change,
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

Help my pc recognizes my ipod touch as a camera device and is not recognized by itunes

When I conect my ipod to my pc it's recognized as a camera device, and when itunes pops up there's just a blank screen with the ipod logo and It can't be sincronized, I've resetted my ipod, i've allready unninstal and installed itunes 10.6 and it makes no difference, please help =(

Start here:
iOS: Device not recognized in iTunes for Windows

Equium P200D PSPBNE: device manager does not show the DVD-RW DVR-K17A ATA DVD/CD

Hello experts out there i need urgent help!!
My Equium P200D all of a sudden it decided to show the DVD/CD Drive in device manager as no longer working due to a corrupt driver??
I am running Vista Home and despite deleting the drive and trying to update the driver nothing seem's to work can anybody help i am getting to the point of throwing it out of the window.
Regards
Stephen

Hi dude
This issue is known to me it happened to me too
The problem is you Windows registry!!!
One registry entry is corrupt and therefore the CD/DVD ROM does not work as I should.
So what to do.
Firstly remove the driver from the device manager. Just simply delete it.
Then access the registry and and remove the Upperfilters and Lowerfilters values completely from the following registry key:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Contro l\Class\{4D36E965-E325-11CE-BFC1-08002BE10318}
Then reboot the notebook.
Check it out

Device Manager is not recognizing my robotic library

Similar Messages

Maybe you are looking for