Device Monitor - Black except for Storage tab

Hi,
My Device Monitor  (from Quick Settings) is completely blank except for the Storage tab. That means Battery, CPU, and Memory are all not loading properly.
Any suggestions?
Merci!
Solved!
Go to Solution.

Hi and Welcome to the Community!
Anytime random strange behavior or sluggishness shows up, the first thing to try is a proper reboot:
Pre-BB10 Devices ONLY. With power ON, remove the back cover and pull out the battery. Wait about a minute then replace the battery and cover. Power up and wait patiently through the long reboot -- ~5 minutes.
BB10 Devices. Hold the top button down until the counter reaches zero. Wait for the device to be fully shut down (e.g., nothing at all displayed on the screen, no LED lights, etc.). Hold the top button until the red LED is lit. Wait through the full boot-up process. If this fails, you can attempt the battery-pull method above, but it is normally NOT recommended unless nothing else works.
See if things have returned to good operation. Like all computing devices, BB's suffer from memory leaks and such...with a hard reboot being the best cure.
Good luck!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4   Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA   Display/Scan Bar Code

Similar Messages

  • Downloaded firefox 5 and now screen is black except for toolbar

    My laptop has windows XP. I downloaded Firefox 5 and my screen is black except for the toolbar. It doesn't matter which site I try to get to, the screen is still black. I had to go to my IGoogle homepage an access the help link because once I go back to Firefox, black screen again. I never had this problem until I upgraded to 5. Any help would be appreciated or I will have to go back to the older version of Firefox.

    Hi Aphthonius,
    Thanks for visiting Apple Support Communities.
    If you only see the "connect to iTunes" screen on your iPhone, this means that the device is in recovery mode and needs to be restored. The information and steps in this article can help further:
    If you can't update or restore your iOS device
    http://support.apple.com/kb/ht1808
    All the best,
    Jeremy

  • Hi there, can anyone tell me how to make make Garageband ignore HDMI as an audio output-device on a 2013 Mac Mini? Now it keeps on prompting me: Do you want want to use the HDMI device (monitor without audio) for audio output? Thanks in advance, Grtz T.

    Hi there,
    Can anyone tell me how to make make Garageband ignore HDMI as an audio output-device on a 2013 Mac mini i7 using an Apogee jam as an input for bass and a Behringer USB DAC with RCA audio output? Now it keeps on prompting me: Do you want want to use the HDMI device (monitor without audio) for audio output? I'm also suffering massive audio lag issues with the Apogee jam after waking the mini from sleepmode, wich pretty much renders it useless.
    Thanks in advance,
    Grtz T.

    I think the easiest way to do this is to have the EyeTV app running in one user account and sent via HDMI to the TV, and use a separate user account for Screen Sharing. Both logins can be active at the same time and with Lion you can connect via screen sharing to which ever login you need.
    With regards to the Mac video resolution changing, when it is not the current input on your AV receiver. This is 'normal', if the Mac sees no signal it drops down the a lower level. What you need is to buy a HDMI Detective Plus which tricks the Mac in to always seeing a signal and hence it will not drop down the resolution. See http://www.gefen.com/kvm/dproduct.jsp?prod_id=8005
    The Mac mini does have an IR receiver. This can be used with the EyeTV app, iTunes, and similar. Yes I believe EyeTV would run for prolonged periods quite happily, it is has been around for a long time and had most of the rough edges polished off. However one issue you will have to deal with is that it does not automatically update its program guide data. For this you might have to write or modify an AppleScript. Elgato support or their user forums will be a lot of help.
    You can set EyeTV to convert recordings to an iTunes (Apple TV) compatible format and then delete them from EyeTV.
    The HDMI Detective should solve your handshaking problems.

  • AFter the standard screensaver kicks in, all Firefox windows go totally black except for the title bar,; only closing & restarting FF Fixes.

    Windows XP SP3. This started with Firefox v.18.0. When any activity cancels the screensaver, all display returns as before, except Firefox. FF window will close using the corner "X", but no other toolbars are visible or functional. No new add-ons since the 18.0 update.

    This is the closest to the problem I am seeing. When the pc wakes from sleep, some parts of the Firefox window appears black until I minimize/restore it, or close/restart it. Some parts of the window reappear if I mouse over it repeatedly. This is relatively new. I don't usually report minor problems like this unless they repeat.
    Win7-64b
    Firefox 19.0.2

  • I have lost one of my devices (ipad2) and i cannot seem to find it on my findmyiphone app. all other devices show up except for this one. is there something i can do?

    i cannot seem to actively see/locate my ipad2 on my findmyiphone app. is there a way i can find it using the serial # of my device

    If the iPad was running iOS 7, the thief/finder will not ever be able to use it.
    iCloud: Find My iPhone Activation Lock in iOS 7
    http://support.apple.com/kb/HT5818
    Apple (and no one else) can not assist (with serial number or iCloud) in finding a lost or stolen iPad.
    Report to police along with serial number. Change all your passwords.
    These links may be helpful.
    How to Track and Report Stolen iPad
    http://www.ipadastic.com/tutorials/how-to-track-and-report-stolen-ipad
    Reporting a lost or stolen Apple product
    http://support.apple.com/kb/ht2526
    What to do if your iOS device is lost or stolen
    http://support.apple.com/kb/HT5668
    iCloud: Locate your device on a map
    http://support.apple.com/kb/PH2698
    iCloud: Lost Mode - Lock and Trace
    http://support.apple.com/kb/PH2700
    iCloud: Remotely Erase your device
    http://support.apple.com/kb/PH2701
    Report Stolen iPad Tips and iPad Theft Prevention
    http://www.stolen-property.com/report-stolen-ipad.php
    How to recover a lost or stolen iPad
    http://ipadhelp.com/ipad-help/how-to-recover-a-lost-or-stolen-ipad/
    How to Find a Stolen iPad
    http://www.ehow.com/how_7586429_stolen-ipad.html
    What NOT to do if your iPhone or iPad is lost or stolen
    http://www.tomahaiku.com/what-not-to-do-if-your-iphone-or-ipad-lost-or-stolen/
    Apple Product Lost or Stolen
    http://sites.google.com/site/appleclubfhs/support/advice-and-articles/lost-or-st olen
    Oops! iForgot My New iPad On the Plane; Now What?
    http://online.wsj.com/article/SB10001424052702303459004577362194012634000.html
    If you don't know your lost/stolen iPad's serial number, use the instructions below. The S/N is also on the iPad's box.
    How to Find Your iPad Serial Number
    http://www.ipadastic.com/tutorials/how-to-find-your-ipad-serial-number
    iOS: How to find the serial number, IMEI, MEID, CDN, and ICCID number
    http://support.apple.com/kb/HT4061
     Cheers, Tom

  • Tab labels are grayed out except for active tab. This was not always the case. How to fix this?

    I recently had the 29 upgrade forced on me. I did not like the new lay out. I was trying different things and I hit the restore defaults button. After I did this, any tabs that I had open that were not the active tab, the labels was grayed out. I want the labels to stay the same. How do I get this fixed?

    Why do I have to install an extension to get back to the style I want to use? This is ridiculous.

  • My printer will not print in black except for the top and bottom headings. The rest prints in turq.

    I usually choose grayscale, but it is being ignored. Today, the turq. has changed to a green.

    My printer is a Photosmart 3210 all-in-one.

  • I RESET. MY SCREEN IS BLACK EXCEPOT FOR THE SPINNING WHEEL AT THE BOTTOM. IS IT BROKE?

    I TRIED TO DOWNLOAD AN APP TO HELP FIND MY PICS AFTER AN ACCIDENTAL RESET AND NOW MY ITOUCH DOESNT WORK. THE SCREEN IS BLACK EXCEPT FOR A WHITE SPINNING WHEEL AT THE BOTTOM. IS IT BROKEN?

    Try:                           
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try another cable
    - Try on another computer                            
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar                                     

  • Portg Z30-A-1E1 - External monitor blacks out randomly

    Very annoying problem - every now and then the monitor blacks out for 2 seconds and comes back.
    Monitor is powered all the time.
    HDMI cable changed twice and does not solve the problem.
    Seems like a change of resolution or a reset - can the problem be in the graphic card? Otherwise maybe the HDMI port itself detecting strange stuff?
    Please help I'm getting crazy as I work 90% of the time on external monitor.
    Thanks
    MAx

    Originally Posted by ammtosh
    I would try the French service, Toshiba is an international company. If you have a problem with your Italian car in France you go to the French workshop...
    Yes maybe you are right. Still, annoying not being a fluent French speaker to have to deal with them.... and with 90% possibility that they'll say "if you bought in Italy you should talk to them". I'll try.
    PS: another ridiculous thing: you buy a product that has a problem, and you need to pay to call the support service? Really not acceptable....
    The dark side is strong.... actually, I start wondering which is the real dark side. Theory of relativity!

  • Black Screen on startup with message saying searching for storage devices

    1. Hp Pavillion Desktop a6720y
    2. Windows Vista 64 bit
    3. S​earching for storage devices at startup
    4. No changes made that I can think to software or hardware

    Soundmaster, welcome to the forum.
    It appears that you have a failed hard drive.  You can run SMART diagnostics from the BIOS to see what it says.
    Please click "Accept as Solution" if your problem is solved.
    Signature:
    HP TouchPad - 1.2 GHz; 1 GB memory; 32 GB storage; WebOS/CyanogenMod 11(Kit Kat)
    HP 10 Plus; Android-Kit Kat; 1.0 GHz Allwinner A31 ARM Cortex A7 Quad Core Processor ; 2GB RAM Memory Long: 2 GB DDR3L SDRAM (1600MHz); 16GB disable eMMC 16GB v4.51
    HP Omen; i7-4710QH; 8 GB memory; 256 GB San Disk SSD; Win 8.1
    HP Photosmart 7520 AIO
    ++++++++++++++++++
    **Click the Thumbs Up+ to say 'Thanks' and the 'Accept as Solution' if I have solved your problem.**
    Intelligence is God given; Wisdom is the sum of our mistakes!
    I am not an HP employee.

  • W530, W7-64: external monitor is dark except for mouse pointer

    Hello,
    I'm starting to experience this problem. Initially I had no problems with using an external monitor, but now I cannot use it. When I switch to the external monitor, the screen is dark, except for the mouse pointer which moves correctly.. Anyone know the cause of this problem?
    Regards,
    bostjanv

    I have had same problems using NVIDA Q2000K when using Windows 8.  Try configuring with NVIDA instructions for multiple displays as follows: 
     ThinkPad W530       NVIDIA Quadro K1000M or NVIDIA Quadro K2000M           - Computer's analog VGA connector           - Docking Station's analog VGA connector           - Computer's DisplayPort connector           - Docking Station's DVI connector(s) or DisplayPort connector(s)
          Intel HD Graphics Family           - (Computer's LCD)
    DUAL ADAPTER CLONE
      Dual Adapter Clone is a technology where display output from one display   adapter is cloned to another display adapter. This feature is unique for   NVIDIA Optimus Technology starting from second generation Optimus technology.   The only difference between cross adapter clone and traditional clone is that   the former involves two display adapters while the latter involves only one.
    HOW TO CONFIGURE DUAL ADAPTER CLONE
      Dual Adapter Clone is only supported and be configured in NVIDIA Control Panel.   As an example, the procedure below describes the steps on how to configure the   dual adapter clone. Remember that the dual adapter clone involves two   different graphics devices, so the 'Display Topology' section above will give   you an idea which combinations can support dual adapter clone, otherwise, it   is considered as a traditional clone.
      The procedure below assumes to use the LCD and DisplayPort monitor connected   to the computer.   1. Attach a DisplayPort monitor to the computer.   2. Open the NVIDIA Control Panel, and on the left pane, select 'Setup multiple      displays' under 'Display' tree.   3. On the right panel, under 'Select the display you want to use', check both      LCD and DisplayPort monitor.   4. Under 'Verify your display configuration', right click on either the LCD or      DisplayPort display icon.   5. Select 'Duplicate with 1 (use 2 as source)' then click Apply.
      Note: The Dual Adapter Clone can not be enabled by using the Windows display         control panel or the Intel's display control panel.
    Windows 8 also disabled my NVIDA Q2000K and I had to restore it.  I hope this was helpful.
    Jack
    Jack

  • Z87-G45 USB Mass Storage & other devices not working (except keyboard/mouse)

    My Z87-G45 died on me last month in warranty so I received a replacement one.
    Unfortunatly I'm experiencing mayor USB issues.
    - In Bios mode, no USB mass storage devices are detected (usb stick/disk). USB keyboard and mouse work fine
    - In Windows no USB device except for the keyboard and mouse are detected.
    - Can't see USB Mass Storage Device driver in the USB controllers list
    Installed all latest drivers + CMOS CLEAR just in case. Results stay the same.
    I assume it's best that I return the motherboard?
    Kind regards
    Frederick

    Quote from: frederick.dhont on Today at 02:43:46
    All drivers are already all up-to-date
    I also want to stress that USB mass storage devices are not detected in BIOS, NOR as bootable USB device. So I can't upgrade BIOS even if I wanted to.
    have you done >>Clear CMOS Guide<< with power cord removed?
    have you tested with mainboard out of PC case placed over wooden table?

  • I have multiple devices with the same cerificate, once I have a an exception for one, FF denys access to the others. I cannot change the certificates, I need to stop FF blocking them.

    I have multiple devices with the same cerificate, once I have an exception for one, FF denys access to the others. I cannot change the certificates, I need to stop FF blocking them.
    == This happened ==
    Every time Firefox opened
    == I attempt to access a web front end on an IBM SVC device

    You can't use the same certificate more than once.
    See also [[Certificate contains the same serial number as another certificate]]

  • I have a production mobile Flex app that uses RemoteObject calls for all data access, and it's working well, except for a new remote call I just added that only fails when running with a release build.  The same call works fine when running on the device

    I have a production mobile Flex app that uses RemoteObject calls for all data access, and it's working well, except for a new remote call I just added that only fails when running with a release build. The same call works fine when running on the device (iPhone) using debug build. When running with a release build, the result handler is never called (nor is the fault handler called). Viewing the BlazeDS logs in debug mode, the call is received and send back with data. I've narrowed it down to what seems to be a data size issue.
    I have targeted one specific data call that returns in the String value a string length of 44kb, which fails in the release build (result or fault handler never called), but the result handler is called as expected in debug build. When I do not populate the String value (in server side Java code) on the object (just set it empty string), the result handler is then called, and the object is returned (release build).
    The custom object being returned in the call is a very a simple object, with getters/setters for simple types boolean, int, String, and one org.23c.dom.Document type. This same object type is used on other other RemoteObject calls (different data) and works fine (release and debug builds). I originally was returning as a Document, but, just to make sure this wasn't the problem, changed the value to be returned to a String, just to rule out XML/Dom issues in serialization.
    I don't understand 1) why the release build vs. debug build behavior is different for a RemoteObject call, 2) why the calls work in debug build when sending over a somewhat large (but, not unreasonable) amount of data in a String object, but not in release build.
    I have't tried to find out exactly where the failure point in size is, but, not sure that's even relevant, since 44kb isn't an unreasonable size to expect.
    By turning on the Debug mode in BlazeDS, I can see the object and it's attributes being serialized and everything looks good there. The calls are received and processed appropriately in BlazeDS for both debug and release build testing.
    Anyone have an idea on other things to try to debug/resolve this?
    Platform testing is BlazeDS 4, Flashbuilder 4.7, Websphere 8 server, iPhone (iOS 7.1.2). Tried using multiple Flex SDK's 4.12 to the latest 4.13, with no change in behavior.
    Thanks!

    After a week's worth of debugging, I found the issue.
    The Java type returned from the call was defined as ArrayList.  Changing it to List resolved the problem.
    I'm not sure why ArrayList isn't a valid return type, I've been looking at the Adobe docs, and still can't see why this isn't valid.  And, why it works in Debug mode and not in Release build is even stranger.  Maybe someone can shed some light on the logic here to me.

  • I recently purchased the new nano (7th generation) and I love it except for one issue.  On my old 2nd generation nano, when I played podcasts, it would play podcasts one at a time. So if I had 20 episodes of a podcast on the device, it would stop at the e

    I recently purchased the new nano (7th generation) and I love it except for one issue.  On my old 2nd generation nano, when I played podcasts, it would play podcasts one at a time. So if I had 20 episodes of a podcast on the device, it would stop at the end of each one.
    With the new nano, I can select and play a podcast, but when it’s over, it goes straight to the next one without prompting.  It keeps on playing all of the episodes of any podcast until you stop it manually.  Setting the repeat function differently does not prevent episodes from being played automatically.
    This can be very irritating when I only want to listen to one podcast.  I’ve often fallen asleep listening to one episode of a podcast, only to be woken up hours later by the iPod working its way through all subsequent episodes.  It is also annoying that any podcast which has started automatically in this way is marked as ‘played’ – even if you stop it within a few seconds.  This makes it hard to keep track of what you have actually listened to.
    Is there any way to set the iPod to play all the podcasts individually? I have read the User Guide from cover to cover, and can’t find a way of doing this.
    MD

    Dude or hot-spur,
    Not fishy at all!!!! You really think I would have taken any more of my time to post a bogus rant? We'll no, it is unfortunately all true. I want to hear from anyone who is experiencing such problems not anyone else that wants to put there two cents in. I really don't need anymore hate or negativity. Just people's experiences because I feel like I am the only one having so many problems. Thank you
    Yes, I have had some unfortunate bad luck to have so many problems at the same time, but some of them are just things you cannot do on the new OS.
    Thank you again

Maybe you are looking for

  • How to create a report with a PL/SQL Stored Procedure method

    Hi, We are working in oracle applications 11i on oracle database 9i. I have a custom procedure that is used to send Payslip SMS messages to staff. I am thinking about creating a request for that procedure so the HR user can run it himself at the end

  • Can i use the ipad 2 3g bought in the philippines in usa?

    Planning to buy ipad2 3g in the philippines, will the 3g work here in usa?

  • Can't restore my mini!

    I accidentally unplugged my mini before ejecting it (thought it was my mouse cord...whoops!), and it erased all the songs and info. No big deal, since I can reset, restore, update...whatever. Only problem is, I have done all of that, and when I go to

  • New phone line- can I ask to be connected to speci...

    The cul de sac I live on has 46 properties, 20 of which are new builds ( 6yo ) and these new builds have their own small BT cabinet,(mine is one of these new builds). The existing houses on the street are connected to a cab which has just had a new F

  • Default Group Ownership and Permissions

    All new files created by a standard user (User1) have group assigned as "staff" and group permissions set to "Read only."  How do I change the default group and ownership permissions for newly created files? Said another way: I want new files created