Device test failure

i made an scrolling image sequence, that is controlled with moving left-right mouse or finger
there are 120 images and its wheight is 36 Mb
it runs great on desctop as SWF
BUT when published to .ipa and lounched on iPad 2 - black sreen for aboute 5 sec. and throws back to "home"
what does that mean?

Maybe the images are too much for the device to handle, im not sure what code you used, but are you removing your event listeners each time you add a new one? because from IOS experiece I found out that the iphone does not like HD images from flash. I only had about 30, it still worked but performance was not all that great.

Similar Messages

Error Message: PXE-E61 media test failure, check cable

Hi,
Recently when I have loaded up my laptop one of two things has happened:
1) I am taken to Windows error recovery and told that I can either launch windows boot repair or start windows normally. Both lead to a screen which says 'Status: 0xc00000e9, Info: An unexpected I/O error has occurred. It also says that 'windows has experienced a problem communicating with a device connected to your computer. This error could be caused by unplugging a removable storage device, or by faulty hardware such as a HDD or CD-ROM drive'.
2) I am greeted by a black screen with a lot of text, but one line in particular says : 'PXE-E61 Media test failure, check cable'
Having read some forums online I have checked the BIOS and the Hard Drive is being detected sometimes, but other times is 'not present'. On examining the boot order the HDD is registered as the first thing to boot.
I was hoping that some of you would be able to help me out a bit more here, because I'm a bit of a novice when it comes to repairing computers! Any advice that you can give would be appreciated.
My computer is a Toshiba Sattelite-C660D-102
Thanks !

Your hard drive is more than likely failing and will need replaced. You can also check to make sure your hard drive is properly seated and has a good connection.

Message "PXE-E61: Media test, failure, check cable, PXE-M0F: Exiting PXE ROM"

Please help! I have a Satellite L300 laptop, bought in October 2008, and never had any problems until this January. In January I took it to Future Shop under warranty and they had to replace hard drive. Everything was fine until the beginning of April when it started to freeze unexpectedly anywhere from 5 mins after start up to 45 mins later.
It would first go to a blue screen saying it had detected serious problems and would shut down to protect itself, (the page was too fast to read entirely or copy), then on start up would either scan through indexed files, or go straight to a black page with this message:
"Intel UNDI, PXE-2.1 (build 082)
Copyright (C) 1997-2000 Intel Corporation
For Realtek RTL8101E/8102E PCI-E Ethernet Controller v.105 (071227)
PXE-E61: Media test failure, check cable
PXE-M0F: Exiting PXE ROM
No bootable device -- insert boot disk and press any key"
It did this numerous times, and said in the control panel that it had problems but no solutions, and my virus scans came back fine, so I took it back to Future Shop assuming it was the hardware again. They scanned it and said it isn't the hardware, but software could be the problem so they did a system restore.
The day I brought it home it started happening again, so I took it back to see them 2 days later. They said they found nothing doing extensive scans and no messages came up when they used it.
I've tried searching other forums and everything that mentions this message "PXE-E61" says its a hard drive issue. There is nothing on the microsoft, future shop or toshiba forums on this that I can find...curious...The Future shop guy thought maybe it was my router for internet, but it shuts down/freezes in two different locations with completely different internet service.
Any suggestions? I'm desperate and Future shop is useless.

The answer is right above your question.
If you don't post your COMPLETE model number it's very difficult to assist you. Please try to post in complete sentences with punctuation, capitals, and correct spelling. Toshiba does NOT provide any direct support in these forums. All support is User to User in their spare time.

[svn:fx-trunk] 7728: Reverting change 7716 after it caused a bunch of test failures.

Revision: 7728
Author:   [email protected]
Date:     2009-06-10 14:58:37 -0700 (Wed, 10 Jun 2009)
Log Message:
Reverting change 7716 after it caused a bunch of test failures.
Modified Paths:
    flex/sdk/trunk/modules/compiler/src/java/flex2/compiler/common/MxmlConfiguration.java

Did I understand you right that you said that even using a PCI NIC in those systems gave the same errors? That would likely mean that any corruption is in the hardware... the nForce4 chipset or Hypertransport or maybe even mbrd traces? I think there are enough systems out there running satisfactorily that that is not a viable explanation: Hypertransport errors would cause all kinds of hard disk problems as well as with other I/O devices. Are you sure that nothing is (unintentionally) overclocked and have you checked the memory with Orthos http://sp2004.fre3.com/beta/beta2.htm?
There are a couple of things about the nForce NI though: most important is that the TCP offloading is broken and I've had to disable Checksum Offloading and Segmentation Offloading in the Advanced Properties of the nForce Network Controller in Device Manager. This also means that the Active Armor is broken and consequently the nVidia Firewall and NAM (Network Access Manager) are useless. IOW if NAM is installed get rid of it - I've no idea what it might do with other NIs installed in the system... hopefully nothing but then.......
A couple of points to clear up: 1) are you only getting the errors on an internet connection and LAN connections work OK? 2) What are those nForce systems connected to... a hub or switch and through to a router? 3) I'm not sure what "outbound packet errors" means - is it due to the OS seeing that the packets are malformed before they go to the NI, or is it due to the NI getting error responses from the device on the other end of the "wire"?

Error target device access failure

After my return from a week vacation I have not been able to get my MAC Mini server (late2009) to start up. Now I'm able to run a test, which is running right now, but have received error "target device access failure".
Any help or how I can start up my MAC mini will be greatly appreciate it.
Thanks,
Hector

You're not really working with a 10-hour timeline, are you? You can only fit about 60-70 minutes of video on a standard DVD -- maybe twice that on a dual layer disc.
In any event, the best way to find out what's going wrong and when is to use the troubleshooting steps in the FAQs to the right of the forum.
http://forums.adobe.com/thread/415318?tstart=0
If you'll post the results for each step in as much detail as possible, we can help you figure out what's going wrong and how to fix it.
BTW, you're not combining MPEGs and AVIs in the same project, are you?
You definitely want to convert those MPEGs first to AVIs so that only DV-AVIs are going into a project and that project. It will certainly save you a lot of heartache (as well as having to deal with strange interlacing issues) later.

PXE-E61: Media test failure, check cable Error Message

My wife’s Satellite L505 (PULU0U-03C003) with Windows 7 Home Premium has started faulting out to this message on a regular basis, at least once a day or more:
Realtek PCI Express Fast Ethernet Controller Series v1.15 (090224)
PXE-E61: Media test failure, check cable
PXE-M0F: exiting PXE ROM
No bootable device – insert boot disk and press any key
I can power down the laptop and then turn it back on again. After going through the “did not start (I think its called that) window, then computer boots successfully and everything works fine for a time. I have attached a photo of the error message.
I checked as many of the messages as I could but didn’t find anything that seemed quite the same. Any suggestions or thoughts?
Thanks - Chet
Attachments:
Error Message - Delores Toshiba Laptop (2).jpg ‏433 KB

A PXE error typically means that the Boot Priority in the Bios is set incorrectly and the computer is trying to boot from the LAN port. Make sure that the hard drive (HDD) is the first boot device and the LAN port is the last boot device.

PXE-E61: Media Test failure, Check cable in my Lenovo Ideapad U430 Touch.

I have bought my U430 Touch last June, 2014. Recently i am getting the "PXE-E61: Media Test failure, Check cable" error while switching on my laptop. And it does not precede any farther for booting. I have tried disabling the “Network Boot” as well but no luck. It always stuck on the same black screen error. Can you please help me on this issue.

https://forums.lenovo.com/t5/Lenovo-3000-and-Essential/PXE-E61-Media-Test-failure-Check-cable-Lenovo...
if that one dont help other have said reinstalling windows helped as the next thing was a driver issue causing it to fail the check
does your device have a nova button (next to power button very small button use this to turn on the device) if you do use this and there is a factory restore there
Thx dave
yoga 2, lenovo b540
3 custom gaming pc systems

Memory Test Failure:

I was digging in my computer drawers for a plastic thing to hold one of my SD cards, and then I found a RAM chip that is 512MB. I need lots of these for the imacs, but I tried to install it, and it didn't work......
It is a Dell Memory. Make your next upgrade Dell Certified Memory. and there is also the sticker with the M with the circle around it and the small OS9-style font and a bar code.
It came with one of my imacs!!!!! It was inside it already. I don't remember if I took it out before or after one of the imacs stopped functioning. (also...could that be the cause of the damage of my first 500mhz imac??????)
I put it in a dark blue 400mhz imac and it has 10.3.9 and 9.2.2 but I have it set to boot into 9.2.2 and it said "Memory Test Failure" or something like that. Everything booted successfully. And then I went to System Profiler. And it did not say 512MB.
My very first mac was a power mac g3 and it had issues. I thought it would be any number of things. I dismantled it. While I did not have any 512 modules (I want and need lots of them) I decided, reluctlantly, to put in some of the 256mb modules in the imac. And...
One of the modules caused the imac to never boot. I took that one out. I put another one of them in and instead of the chime, it there was a sound that was similar length, but it sounded like a common stand-alone analog television not recieving any signals. That static noise with the white "snow"?? It sounded like that. "BZZZZ"!! I took that one out. There are two 256mbs, but I want 2 512mbs,
and...
THAT is what was wrong with the power mac G3?!?!?!?!?!?! I already took it apart, thinking there wasn't anything easily fixable on it!!!! }=S I guess I will put it together again... But that won't happen until I have some more RAM chips... I do not like 64 mb and 128 mb chips. }=S
All 4 of the 256mbs were functioning. I bought them as used, and it said that it will fit in g3s. Why are 2 of the 256mbs not functioning any more???? I once had Tiger on Power Mac g3. It is a blue and white g3. Could Tiger's Dashboard have zapped the ram chips??!!!!!!!
Anyways, for every imac, I would like 2 512 modules. Which ones will work??? Ones that are certified Dell are obviously not. XD
and will dashboard zap the memory?????? I do not have Tiger installed, but if I install it, will it damage the memory????? =S

Which iMac do you have? All iMac G3 models only have two memory slots.
What iMac do you have?
Query by serial number
"A serial number is a unique, identifying number or group of numbers and letters assigned to an individual piece of hardware or software. It's used for various things depending on the product / brand but what is your Mac's serial number for and more importantly... what is it hiding and what can it do for you ?"
http://www.appleserialnumberinfo.com/Desktop/index.php
or
http://www.chipmunk.nl/klantenservice/applemodel.html
( hint by K Shaffer )
You could buy an external DVD drive. It needs to be firewire and bootable by Mac OS. If you have another PPC with firewire, you could try target Disk mode and installed tiger that way.
You need to figure out the level of your firmware before installing 10.2 or greater. ( The PC name for firmware is BIOS. ) Installing 10.2 with a down level firmware will most likely make your iMac unusable and difficult to fix.
Open Firmware, boot into Open Firmware.
Power on your iMac while holding down commandoption+of
The first output line contains the firmware level. Mine reads:
Apple PowerMac4,1 4.1.9f1 BootRom built on 09/14/01 at 13.18.04
Copyright 1994-2001 Apple Computer Inc.
On my machine, I have 4.1.9f1.
What firmware do you need?
http://docs.info.apple.com/article.html?artnum=86117
For a slot loading iMac, this article indicates that you need to be running 9.1 or later version of Mac OS Classic.
http://docs.info.apple.com/article.html?artnum=75130
"The iMac Firmware Update 4.1.9 will only run on iMac computers with lot-loading CD or DVD drives running Mac OS 9.1 or later from a local drive. If you are using Mac OS X you must boot from a local Mac OS 9.1 or later writeable partition (not a CD, or network disk) prior to following the update instructions."
You can download the Mac OS 9 updates from the Apple site.
http://support.apple.com/kb/HT1387?viewlocale=en_US
For tiger, you need 256meg of memory.

Error message when trying to recover HD: PXE-E61 Media test failure

Hi all, new to forums, lots of good info and support here.
Got the BSOD last week. Have been trying all of the various fixes mentioned on the board, to no avail. I went back multiple pages looking for alternatives to try. After stepping away for a few days, I got farther today than I did when I was frustrated. F12, chose to boot HDD, and got the following LOOPING error message:
PXE-E61 Media test failure check cable
PXR-MDF exiting PXE rom
Which gives me hope that I may not have to replace my hard drive.
I have a satellite L455-5975, and have ordered recovery disc from acclaim ('0' option didn't work for me, which makes me wonder if Toshiba time limits that support, but that's off topic)
So it looks to me like my RealTek Ethernet Controller might be the problem? Any thoughts or suggestions? Anything I can do or should I wait for recovery disk to arrive? I worry that the recovery disk isn't going to do what I need. Do I need to replace the ethernet controller, or is this a sign of a hard drive issue? I consider myself 'fairly' tech savvy, but I've never taken a computer apart/put one together myself. It would definitely cost less for me to replace HD myself than putting it in the shop. So I'm willing to try that option if need be.
I appreciate any help/support! Reading some of the previous posts make me wonder if rather than investing more money in the satellite, if I shouldn't instead be saving up to buy a new(er) model.

Creedym...
I have a very similar problem with my mini-notebook model NB305.
I'm getting the same message and can't get past F2 or F12.
Bottom line; I ordered the recovery data from Toshiba on-line by model number ---not by type. They sent two DVDs. My unit doesn't have an optical drive.
First call to "John"---yes, you can copy the data to a thumb drive and use that.
Almost two hours of transferring --- the NB305 did not respond to the thumb drive.
Second call to "Paul". After some consultation on his part with someone else he told me that they don't make a thumbdrive (USB) recovery disk for my model, that's why I received two DVDs. ! I would have take it to a shop where they etc...
I haven't decided what to do next. Maybe purchase an external drive rather than take it to a repair shop where it will probably cost more than buying an inexpensive external drive.
t.

This device cannot start. (Code 10) Status Device Power Failure for Intel (R) Audio Display

Hi I just bought HP Envy M7 Sleekbook last week and upgraded from 8.0 to 8.1 for Windows 8.
Now I have no sound and this is the error message I get:
This device cannot start. (Code 10) Status Device Power Failure (for Intel (R) Audio Display)
under Sound, Vieo and Game Controllers in the Device Manager.
Anyone else having this issue after upgrading?
Getting a new lappy is stressful enough but to alreay have issues is ridiculous
If the upgrade is not the issue could something have happened in transit? (I have an issue with the way Best Buy packed it for shipment and wonder if it could have been compromised)
Any help is appreciated. Or should Ibe taing this back to best buy and have them address it?
Thanks
Pam

Ahmed, if your HP Envy has an Intel processor chances are it will be necessary to download new drivers for both sound and chipset due to compatibility issues with Windows 8.1. After 4-1/2 hours on the phone with various technical agents and a lot of frustration I finally got one who had the knowledge and training to resolve my issue. I believe he downloaded the new drivers from the HP support site. Good luck!!

[svn] 2263: Fixed WiseUI performance app and some mustella test failures.

Revision: 2263
Author: [email protected]
Date: 2008-06-26 13:19:12 -0700 (Thu, 26 Jun 2008)
Log Message:
Fixed WiseUI performance app and some mustella test failures.
tests Passed: checkintests
Needs QA: YES
Needs DOC: NO
Bug fixes:
API Change: NO
Reviewer: pfarland
Code-level description of changes:
OffsetInputBuffer.java
Added getLineText() override to take the offset into
consideration.
Modified Paths:
flex/sdk/trunk/modules/compiler/src/java/flex2/compiler/as3/OffsetInputBuffer.java

[svn] 4950: * Fixed some junit test failures caused by revision 4939.

Revision: 4950
Author: [email protected]
Date: 2009-02-13 08:31:33 -0800 (Fri, 13 Feb 2009)
Log Message:
* Fixed some junit test failures caused by revision 4939.
tests Passed: checkintests
Needs QA: YES
Needs DOC: NO
Bug fixes: SDK-19299
API Change: NO
Reviewer: Darrell
Code-level description of changes:
Modified compile() by moving check for no inputs above the call to
recompile().
Modified link() to only call FileUtil.getCanonicalPath() if the
output is not null.
Ticket Links:
http://bugs.adobe.com/jira/browse/SDK-19299
Modified Paths:
flex/sdk/trunk/modules/compiler/src/java/flex2/tools/oem/Library.java

[svn:osmf:] 15899: Attempted fix for unit tests failure.

Revision: 15899
Revision: 15899
Author:   [email protected]
Date:     2010-05-04 17:21:06 -0700 (Tue, 04 May 2010)
Log Message:
Attempted fix for unit tests failure.
Modified Paths:
    osmf/trunk/framework/OSMFTest/org/osmf/OSMFTests.as

PXE-E61 Meadia test failure error occurred during installing OS form windows deployment service?

Hi,
I have installed WDS service in my dell server windows 2008 server R2. I am using WDS server and Dhcp server in different machine.I have received error "PXE:E-61 Media test failure check cable ", when I trying to install
OS from my WDS server. But I have created a one partition in VMware and successfully installed windows 2008 R2 server from Windows deployment service. But when I am trying to install the OS in another dell server from WDS, I have received this error.
Any help?

Hi,
For PXE boot, we need the client boot from network. Check your boot option in BIOS settings. Meanwhile, we need WDS server and
DHCP server accessible. If the client locate in a different subnet, IP helper should be configured to point to WDS server and DHCP server.
If everything is configured correctly, I recommend you contact with the manufacture.
Hope this helps.

HELP PLEASE - media test failure - check cable

Hi - I have a toshiba satellite 1955-s801. It crashed on me some time ago and I am now trying to fix it.
The message I receive when I turn it on :
" For Realtek RTL8139 (A/B/C)/,RTL8130 PC/Fast Ethernet Controller V2.12 (010425)
PXE-E61 media test failure - check cable
Exiting PXE ROM PXE-MOF"
This message continues to repeat itself over and over.
I read through alot of messages and decided to try to run the 'recovery discs' from when I first received the computer. There are 3-recovery discs.
I followed the directions, and at this time, I have only put in disk 1.
It kept looping around back to same prompt messages once it said "starting windows 95" . I kept repeating answering the questions with yes and yes.
Now - the screen is stuck on "In Touch with Tomorrow" TOSHIBA.
The recovery disk instructions said not to touch the computer once I start the process. Although, I do not know what to do now. I tried F2 or F12 - but neither does anything. I believe the screen is now frozen.
If anyone is out there and can help, I sure would appreciate it!
thank you
chris

Satellite 1955-S801
Downloads here.
Would a new hard drive fix this computer?
Nobody can tell you for sure, but it's likely.
Maybe it's time for a newer model?
-Jerry

Device test failure

Similar Messages

Maybe you are looking for