Device works fine with MAx but not with Labview visa serial

I have a Monarch rpm sensor hooked up to Monarch tachometer , it gives error while coding in labview and works fine in Max if the sensor doesn't read 0. I have written simple RS-232 programs never had an error but this one is giving errors ..not ablt to fix it..please help
Solved!
Go to Solution.

No device can actually measure a speed of zero.  It can only specify that the speed is less than some minimum, which depends on how long you are willing to wait for an answer.
I do not know anything about your instrument, but I would guess that you are getting an error which is the equivalent of "The instrument has waited the maximum permissible amount of time and did not detect any measurable motion."  This is the instrument's way of saying that the speed may be zero, or very slow, or something is broken so that it cannot make a measurement but it cannot detect the problem.
Look at the manual for you instrument to see how it responds to the zero speed condition.  This error may be normal.  If so, you need to capture the particular error code and handle it however you think is appropriate.
Lynn 

Similar Messages

  • ITunes/Apple Mobile Device works fine w/iPod but not iPad

    Hi. I'm getting stuck on this and would like some help to solving this problem. Basically I'm trying to sync my iPad; however, whenever I connect it, this meesage pops up: "this iPad cannot be used because the Apple Mobile Device is not started." The problem is that when I try to plug in an iPod using the same wire, it works fine, no problem, but the iPad just won't connect. I have since uninstall and reinstall all Apple components (iTunes, AMD, QuickTime, etc) and it's still the same thing...iTunes connects fine w/ the iPod, but not the iPad. What to do? Thnx in advance.
    EDIT:
    Btw, I've tried to connect the iPad while the iPod is connected, and the "Apple Mobile Device is not started" error message pops up too, which is weird, because the iPod is connected and syncing at that time...which means the Apple Mobile Device thing IS started. >.>

    The iOS devices use Apple Mobile Device Service, while older iPods use the iPod Service.
    Checkout this Apple document -> How to restart the Apple Mobile Device Service (AMDS) on Windows
    Are you able to restart the service after following the steps in that article?

  • URGENT: Rest web service with get method works fine in browser but not with java client(Android)

    Hi ,
    I have created one REST web service which accepts two parameters send back JSON results.
    I tested the it in browser with URL as http://+Inteernal server+/ords/utimes/login_info?p1=+first_param+&p2=+second_para+
    Web service URL :  http://+Inteernal server+/ords/utimes/login_info?p1={p1}&p2={p2}
    But when java team wants to access it from java code it gives error as "400- Bad Request".
    one more IMP thing : when I test it in RESTful web service by using "set bind variable" , it only set value of first parameter.
    APEX version : 4.2
    Database : 11g (XE)
    ords : 2.0.8
    please help me ASAP.
    regards,
    Nagesh Patil

    Hi Pragya,
    thank you for the update.
    Another question: could you please give us any reference about these corrections you told about? Maybe they could be relevant in our case too.
    Our raised incident number is: 3100851983
    Kind regards,
    Davide

  • Why does the FP 10 work with firefox but not with IE8

    I down loaded the folowing for xp FP uninstall, FP plugin and FP debug from the link in one of your replys. now I can watch youtube  with firefox but not with IE8. you asked me before if i was using 16 bit. whats that mean and how do I find out? please help I just want to watch youtube on IE!

    Ok Shag, since you hadn't been on a Forum before, then I'll take some of what I said back:-) I wanted you to stay on one thread, you can get in trouble trying things that may cause you more problems than you had in the beginning. I just had your best interest at heart
    I'll even overlook your all caps here:-) At least you responded
    Now since you say you fixed it, what you should do is to confirm it is fixed by taking a look at your Flash folder. This contains all of the Flash files for IE and FF. Then make sure you have the IE add on and the FF add on. That way if you have any future problems, at least you would know it is not the Flash Player.
    You should only have 2 .exe files for IE and 1 for FF.
    For Video editing, I would check Microsoft and see what they have. Perhaps someone else will come along with other info for you.
    No, I don't get paid here, since I am not an employee. Just a user helping others, since I had a problem at one time and after 4 hours of researching solved it.
    Let me know if you want to check the Flash files.
    Thanks,
    eidnolb

  • Airport Express works with Skype but not with internet

    Hi,
    I recently bought some new Airport Express' for my company. However, when plugging it in we seemingly get full access, but only Skype seems to work. If I do a search on the internet it can sometimes look like it find the address after a long while, but don't manage to open the page. E.g. writing www.google.com in the search field doesn't give access to that page.
    I brought them home to check if the Airports worked there, and they did. No problem. But at the office the Airports don't. If I connect the same plug which is connected to the Airport into the MAC / PC, then I have full connection to the internet.
    What to do?

    After Grant pointed out the DNS thing, I started to check that part, and I noticed something funny. I called Apple Support regarding the problem, and now it's solved
    Here is my experience:
    1. My Airports worked fine when home, but not at work.
    2. Checking the LAN DNS addresses I received three addresses. 2 in the 158.xx... range and one in the 129.xxx... range.
    3. The Airport Extreme and Airport Express does only support two DNS addresses, and since the two 158.xx... DNS addresses came first in that range the 129.xxx... was left out.
    4. I manually changed one of the 158.xx... addresses to the 129.xxx... address I got on my MAC / PC when I connected directly to the wall and did a "ipconfig /all" on the PC. The three same addresses is listed under network - airport on the MAC.
    5. Now suddenly it all worked. This due to that the two 158.xx... addresses seamed to be internal addresses, and the 129.xxx... address was from outside delivered from our operator.
    Summarized:
    When you receive 3 DNS addresses you MAC and PC can handle it fine, but your Airport not. Find all your DNS addresses and write them down. Enter Airport Admin Utility and do a manual setup. Change one of the two equal address to the third address. Most probably listed as the last DNS address when you are connected directly and type e.g. "ipconfig /all" on your PC or you enter the network settings.
    Best regards,
    Bouw

  • Fixed headers while scrolling works fine in bids but not when deployed to reportserver

    Hi, I am using SQL Server 2008 R2 & deploying a report to reportserver with fixed headers while scrolling, this works fine in bids but not when deployed to reportserver. We are IE 9.
    Thanks in advance...............
    Ione

    Hi ione721,
    Since you have identified the 2 xml files are identical, according to my knowledge, there maybe a compatibility issue with IE 9 and SSRS 2008 R2, so I suggest that you could run the report in compatibility mode. Please make sure you have turned on Compatibility
    View in Internet Explorer 9 by following steps:
    When Internet Explorer recognizes that a webpage is not compatible, you will see the Compatibility View button on the Address bar. Try clicking it.
    When Compatibility View is turned on, the button changes from an outline to a solid color when you view the page.
    The following screenshots are for your reference:
    If you have any questions, please feel free to let me know.
    Best Regards,
    Wendy Fu

  • Can manually subscribe with Windows but not with Mac

    For some reason I am able to manually subscribe to the below feed just fine with iTunes on my PC (Windows XP) but I get an error when trying with my iMac (OS X 10.5.8):
    *http://feeds.feedburner.com/Metalspeak*
    The error I'm getting with my iMac references "An unknown error occured (400)"
    I was troubleshooting a different feed and am getting similar results: it works fine with the PC, but not with the iMac:
    *http://feeds.feedburner.com/MetalsPeakPodcast*
    The error I'm getting on this feed however states "The file might be corrupted, or a file type that iTunes cannot play"
    Can anyone think of why these feeds work with Windows but not with Mac? Any advice is appreciated!

    The problem lies with the URLs for your media files. The one for the top episode is
    http://www.metalspeak.com/episodes/MetalsPeak 10 - GenresPeak.mp3
    This URL contains spaces, which are not allowed in a URL. Browsers - and from what you say iTunes in Windows - handles this by substituting the code %20 for each space when requesting the file; iTunes for Mac does not.
    You need either to change the filename for each media file, removing the spaces or substituting something such as an underscore, and then amending the feed accordingly: or at the least to amend the feed by replacing each space with %20.
    It's the same problem in the other feed.

  • Photos uploaded through icloud control panel are only synced with iphone but not with ipad

    Photos which are uploaded through icloud control panel are only synced with iPhone but not with iPad. Photos taken with iPhone or iPad are synced with all devices. So, why I do not get the uploaded photos from my pc to iPad? I alredy disabled photo stream on all devices - same failure

    If only one device is not getting updated data, you need to troubleshoot that device and not photostream itself.
    Verify that ipad is connected to wifi, charged over 20 percent, camera app is closed and take a photo of the screen (or anything else, but then close that camera app).
    Open photostream folder on that ipad and see if picture shows up. If you network is good, should not take long.
    Don't forget that while your phone can use wifi and cellular (even it suppose to use wifi for photostream, cellular networks got much better since original photostream was implemented) - you ipad is probably wifi only.
    If picture shows up - you ipad and photostream have no problems and you can go to other devices one by one.

  • I get sound from Youtube with Safari but not with Firefox

    I get sound when using my MacPro with Safari but not with Firefox.

    Did you check the volume setting in the player to make sure that the sound isn't muted?
    You can try to clear the Flash local storage.
    Flash Website Storage Settings panel:
    *http://www.macromedia.com/support/documentation/en/flashplayer/help/settings_manager07.html
    Flash Local storage settings Help:
    * http://www.macromedia.com/support/documentation/en/flashplayer/help/help02.html

  • BB does sync media with PC but not with Mac

    my BB does sync media with PC but not with Mac. At my Mac I got 'Insert media card'. How can this be solved as PC is no problem?

    I got the Bold 9790. I am not sure which OS, does that matter? Are there OS versions not compatible?

  • Serial communicat​ion works in hypertermi​nal but not in LabView

    Hello,
    I am trying to control an APP Automated Pressure Controller using LabView 6.1 via a serial connection.  I am able to control the system with Hyperterminal but not with LabView.  I set used the same setup (9600 baud, 1 stop bit, no parity, no flow control, etc) in LabView that worked in hyperterminal.
    According the the documentation from the Pressure Controller: "Every character that is sent to the controller is echoed back to your computer so you can check to see everything is working.  When a valid command is given, the controller will also send a carriage return (acsii 13) followed by a line feed (ascii 10) to signify the command was executed.  Before sending any commands, the program should clear any characters in the input buffer that may be there from previous responses."
    In hyperterminal, when I type in a command such as "OA", the Pressure Controller responds (without pressing enter or any other keys) and I can see the "OA" on the screen.  As soon as the Controller is done responding, the cursor moves down to the next line (which I assume is caused by the carriage return and line feed) and waits for the next command.
    I have tried to use the Serial Communication.vi with no success.  Does Hyperterminal add (or Labview omit) a special character or command that I am missing?  Do I need to do something special to clear the input buffer in LabView?
    Thanks for any help.
    Alex

    Hello,
    Try to run your application in other system (computer),
    frequently some PCs configurations are not recognized by LabVIEW serial
    routines. I do not know exactly the problem but is not the first time I know
    that kind of problem.
    Sometimes the problem comes from the serial property called
    Termination Character that enables receive buffered data once you have a
    Carrier Return or a Line Feed symbol (Hex 0D/0A) character into the buffer. Try
    to set it true and assign a 0A Hex Value.
    For sending information you need to finish all command
    message with an enter symbol concatenating both (Message + Hex 0D0A) using the
    special character in the string palette library. This action permits system to
    put out buffered data. 
    Good Look

  • 8.5 Report works with OCX but not with CRAXDRT

    Post Author: kjwatson
    CA Forum: Older Products
    I have an application using Crystal Reports 8.5.  It uses the crystal reports OCX to view and print reports.I added the CRAXDRT to the application so I could export PDF files.  It works fine except that Running Total Fields and Formula Fields to not seem to evaluate correctly.  Formula Fields only work if they reference a Database Field.  If they reference a Running Total Field, they do not evaluate. I'm initializing the connection of the tables on the report and sub-reports.  Could I be missing something else? The reports work fine with the older OCX, but not with the CRAXDRT. Any help/ideas are appreciated!Thanks,Kevin 

    Post Author: kjwatson
    CA Forum: Older Products
    I have an application using Crystal Reports 8.5.  It uses the crystal reports OCX to view and print reports.I added the CRAXDRT to the application so I could export PDF files.  It works fine except that Running Total Fields and Formula Fields to not seem to evaluate correctly.  Formula Fields only work if they reference a Database Field.  If they reference a Running Total Field, they do not evaluate. I'm initializing the connection of the tables on the report and sub-reports.  Could I be missing something else? The reports work fine with the older OCX, but not with the CRAXDRT. Any help/ideas are appreciated!Thanks,Kevin 

  • Typekit works with Dreamweaver but not with Muse?

    Why is it that I can use all Typekit's fonts together with Dreamweaver and not with Muse?
    The fonts currently available via the TypeKit font menu in Muse (3.1) are of very low quality. 98% of them are "display type fonts" at best in my humble opinion. I need high quality fonts when designing high quality projects for my customers.
    If I want to use Minion Pro or Futura in my Muse projects — are there any workarounds that does not get lost when I update the site with Muse? For example via the "HTML for <head>" field via the Page Properties dialog window in combination with some other Muse features?
    Does the Adobe Muse Team (or someone else) have a step-by-step guide how to accomplish this?
    Thanks a lot!
    Kudos to The Adobe Muse Team –  Muse is a fantastic piece of software. Easy to work with and really fun to use. Looking forward to the next update!

    This is strange, but hopefully good. 
    I searched for Typekit, fonts and Muse etc on the forums before posting and did not get any relevant hits. But now I think I've found the workaround in the column to the right of this very post under the headline "More Like This".
    http://museinsider.com/how-to-add-typekit-fonts-to-your-muse-site.html

  • Setting margins works with ExportToDisk, but not with ExportToStream...

    I'm filling out a report with SetParameterValue, and not with database, and setting the margins with:
    templateCredencial.ReportDefinition.Sections["DetailSection1"].ReportObjects[elementNumber].Top;
    templateCredencial.ReportDefinition.Sections["DetailSection1"].ReportObjects[elementNumber].Left;
    After that when i call ExportToDisk to write as pdf, the margins that i setted are there, but when i use ExportToStream like that:
    MemoryStream stream = (MemoryStream)credentialTemplate.ExportToStream(ExportFormatType.PortableDocFormat)
    And call stream.ToArray() as return in FileResult, the pdf that shows up on browser is without the margins that i setted. Does anyone have idea how can i return the pdf to the browser with correct margins without get file from disk, using only the stream?

    I don't know because you did not say what the results were or answer any other questions I asked.
    I said what the results were in first post:
    And call stream.ToArray() as return in FileResult, the pdf that shows up on browser is without the margins that i setted. Does anyone have idea how can i return the pdf to the browser with correct margins without get file from disk, using only the stream?
    And, where are you other questions? Sorry, i didn't see it.
    Why can't you simply export to Disk and then stream that file?
    I need performance, and if i need to write a pdf with 10mb, and after read it, and next return (with asp.net mvc 3) to browser like a FileResult, i 'll lose performance.
    What is the right way to change the margins and return it like a byte array without losing the margins that i setted?

  • Can't FLIP a quick RENDER! Works fine in SHAKE but not to flip or Disk!

    Learning with Lynda.com!
    Part 1 has you rendering two files, one is a still image, the other a quicktime movie, I don't have the money for premium so I got my own clouds movie (.mov) and added a still plane.
    I key framed 1 - 100 and playing it back its fine in shake, but not on FLIP or DISK, its nothing but a still image. Have done it 5 times making sure that all the right buttons are on, or not, and as I said, it works INSIDE of shake but won't RENDER to FLIPBOOK!
    I don't suppose anyone wants to send me the exercise files? (on knees begging LOL) I am a member, just can't afford $300 for one pop and this is really the only program I need to learn.
    Thanks!

    Sorry if I'm pointing out something obvious that you already know. Have you checked the time range in the render dialog? Shake does not fill in the values for you automatically, and defaults to "1" so only renders the 1st frame. It needs to be set to eg "1-100".

Maybe you are looking for