Devices not working :/

FFirst off my phone won't sinc all my music I have over 40g of memory it syncs part but not all. Second off my phone has bugs like for real it just restarts all the time especially in my music app whicy hardly works anyways. My iPad and macbook are starting to do it too I can barley use the device without a glitch. I don't know what to do. I Think it's the update.

Have you checked to see if there is a LaCie firmware update? That is actually first thing I would do and is very likely, and has been noted previously.
There are a few out there with a FireWire port not working at all.
Your LaCie has FW400/800 ports?
You can always run the combo update to 10.4.x.
I would look for a new FW800 case if LaCie doesn't have any firmware or help.
http://www.macsales.com/firewire - I have half a dozen FW800 etc from here.

Similar Messages

Dual-Boot; Restart and boot other o/s USB devices not working

I have issue with my msi z97-g43 mobo and Windows dual o/s PC.
Booting with win-8.1, USB devices working very well.Restaring windows 8.1 have NOT any issue.
After shutdown & start PC, choosing to boot windows 7 on bootmanager, USB devices not working in Win-7.
System no hang or occur any error/BSOD message.All startup programs run as normal.
I tried to re-plug usb devices but notting happens... Still not working
But after the win-8.1 shutdown, if i switch off PSU power button, watting ~1 munute for discharge.
After power up PC and boot with windows 7 all usb devices works normaly.
I checked all internal connections. 2 times disassembly all hardware and re-built system, nothing changed.All windows updates and latest drivers installed.
I'm sure other H/W is OK, but I thnik this mobo have a fault.

Thank you for reply.My PC system specs:
CPU:    Intel Pentium G3258 3.2ghz
Board:    MSI Z97-G43 /Bios: Ver. V17.7
MEM:    G.Skill Ripjaws 2x4gb DDR3-1600mhz cl9 1.5v F3-12800CL9-4GBRL
VGA:    Sapphire AMD Redeon HD6670
CASE:    Zalman z3 plus white (5x 120mm fan)
PSU:    Thermaltake Litepower 500w (12v1+12v2=36amp)
HDD-1:    Seagate 1TB ST1000DM003 /HDD-2: Seagate 2TB ST2000DM001
COOLER:    Akasa 92mm PWM Blue Led
OC:    CPU:Default /MEM: X.M.P mode=1600mhz 9-9-9-24-2t 1.5v
O/S:    Win7 x64 PRO + Win8.1 x64 PRO (Genuine)
All hdd's have MBR based partition table.Windows 7 & 8.1 installed in non-efi mode.In BIOS Boot sequence is setting up to non-efi Boot(system) drive as primary.
Before I suspect maybe have a short circuit to pcb or similar thing cause this issue.I take out all parts outside the chassis, and ran this system on the antistatic bag and box.Nothing has been changed.
I have Cooler Master Devastator(MB24 + MS2k) USB keyb+mouse set and tplink wn722n usb wireless dongle.
I have one more pc,based on AMD 970+SB950 chipset mainboard and AMD CPU.I exchange all parts to this amd mainbaord and tested for faulted hardware.All intel system H/W's is ok.All works great
Dual boot works perfectly.Not needs to switch off psu/power back and run system again.
I think msi z97-g43 mainbıoard have a problem.

I have an Ipod Touch, it appears inactive and says conect to Itunes. When I connect it to the PC, the PC says "USB device not working". How can do to solve this problem.

I have an Ipod Touch, it appears inactive and says "connect to Itunes". When I connect to the PC, the PC says "USB device not working". How could do to solve this problem?

See:
iOS: Device not recognized in iTunes for Windows
I would start with
Removing and reinstalling iTunes, QuickTime, and other software components for Windows Vista or Windows 7
or
Removing and Reinstalling iTunes, QuickTime, and other software components for Windows XP

Streaming Audio through Iphone 5 to desktop or laptop using bluetooth preinstalled on all devices not working. Help!!!.

Streaming Audio through Iphone 5 to desktop or laptop using bluetooth preinstalled on all devices not working. Help!!!. Does anybody else have this problem?. Or does anybody have a solution to the problem. If So please help me its driving me demented seriously concidering to go to android for that sort of stuff cause of the dame restrictions on apple devices!

iOS devices do not pair with computers, as data transfer over bluetooth is not supported.
Computers are not airplay compatible unless you have downloaded an app to make them so.
User to user forum, so I don't care if you switch to android or any other threats you make.

My laptop biometric device not working.

HI,
I am facing one problem with my hp pavilion dv6 6160se biometric device not working and i also lost my recovery deta. kindly provide me the solution.
and my system also very slow how can i make it fast.
m. asif

Hi there @Sweeto684
Welcome to the HP Support Forums! It is a great place to find the help you need, both from other users, HP experts and other support personnel.
I understand that your fingerprint reader is not working and that your system is running very slow, but please clarify what you mean by saying you lost the recovery data. Are you referring to the factory recovery image stored on your system, or are you meaning something else?
I am happy to help you with all of this, but need to know more before I can make some useful recommendations. I want to avoid having you do something that could cause a problem with something else, until I know what problem really is.
Malygris1
I work on behalf of HP
Please click Accept as Solution if you feel my post solved your issue, it will help others find the solution.
Click Kudos Thumbs Up on the right to say “Thanks” for helping!

In My IPhone the sound device not working properly. I can here the sound through head set only.kindly send an idea ti solve this problems

In My IPhone the sound device not working properly. I can here the sound through head set only.kindly send an idea ti solve this problems

Hello. I sent my WRT1900AC V1 to Linksys four days ago (Monday) via UPS with a RMA. Linksys paid the shipping and everything. The router is still in route, and it should arrive to their offices tomorrow. Once they receive the WRT1900 AC V1, they are going to send me an EA8500 as a replacement. But I have been reading the comments about the EA8500 here in the forum and it seems to have the same problems. I guess the firmware is extremely flawed in both routers (maybe it is almost the same code?). Anyway, I will try the EA8500 and I hope it works. I bought a temporary router from Walmart and I paid $35 for it. It is a Belink N600 DB. I can't believe that a $35 router is working a lot, lot, lot better than my previous $250 WRT1900AC router. Unbelievable. If the EA8500 doesn't work, I'm going to try and get my money back from Linksys, or contact The Consumerist or someone to get my money back and get a Nighthawk instead.

Iphone 4S will not charge, error that USB device not working, found any suggestions?

iphone 4S will not charge, error that USB device not working, found any suggestions?

Hello Chambless,
The troubleshooting steps below can help get your iPhone to charge.
If your battery doesn't charge, or if your device shows a low-battery image, black screen, or "accessory not supported" alert, follow these steps.
Inspect the connector at the bottom of the phone:
Make sure that there are no bent pins in the connector.
Make sure that the connector is free from debris.
If there are bent pins or debris, please contact Apple Support.
Otherwise, continue troubleshooting.
Make sure that the outlet you're using works.
Make sure that the Apple USB cable and Apple USB power adapter work.
Plug the device in to power and let it charge for up to 30 minutes. If you don't have an Apple USB power adapter, try connecting to a computer's high-power USB 2.0 port (not a keyboard). The computer must be on.
If the device still exhibits an issue, try turning your device off and then on again while connected to power.
If the issue is persists, please contact Apple Support.
iPhone and iPod touch: Charging the battery
http://support.apple.com/kb/HT1476
Cheers,
Allen

Upon running Norton Security Suite Diagnostic Report on my HP Pavilion dv6 Notebook PC on a Windows 7 Home Premium platform, it shows 2 (hidden) devices not working: Antilog32, and AODDriver4.1--Code 24.

On the General tab for device status it says: "This device is not present, is not working properly, or does not have all its drivers installed. (Code 24)" The only option available when I click
on properties of both devices is Start. When I click on Start for Antilog32, this message shows: "The system encountered the following error when it attempted to start the service: The system cannot find the file specified." For AODDriver4.1, the
message when you click Start on Driver tab is: "The system encountered the following error when it attempted to start the service: The system cannot find the path specified." I do not know how to proceed or
how to fix this, or where to find a solution. Please help!

Hello pds48478480,
Do you mean you got the error code 24 in Norton Security Suite Diagnostic Report?
Please share us a screenshot for better analyzation.
Please take a look at the following thread about the AODDriver4.3.
http://answers.microsoft.com/en-us/windows/forum/windows8_1-performance/the-aoddriver43-service-failed-to-start-due-to-the/cb6b7f03-922b-4b82-972f-e92ef9919964
AODDriver 4.3 is used by AMD OverDrive which tune parameters to help system stability, optimize performance, and control cooling/acoustic characteristics.
With the issue description it seems the driver and the service is either stopped or not working correctly.
Refer to the link below and install the latest version of AMD OverDrive.
http://www.amd.com/en-us/markets/game/downloads/overdrive
Please note: Since the website is not hosted by Microsoft, the link may change without notice. Microsoft does not guarantee the accuracy of this information.
Best regards,
Fangzhou CHEN
Fangzhou CHEN
TechNet Community Support

Windows 7 x64 USB AUDIO DEVICE - Device Not Working - Mac Pro

I have a mac pro early 2009. I had vista x64 installed, everything was great. I had 2 audio devices under device manager, one was listed as HD (digital) and one device was listed as analog audio.
When I played games and wanted the external speakers (using the digital out connection) I had the HD (digital) audio device enabled.
When I played games and wanted to use a headphone/microphone combo, I had the analog audio device enabled.
Switching between the two was as easy as clicking the audio device icon and clicking on whichever device I wanted.
Now that I installed windows 7 x64, I have a HD (optical out) device in device manager and it works perfectly. Unfortunately, I also have another device listed called "USB Audio Device" and it shows a yellow exclamation mark next to it and it is NOT working properly.
I tried many suggestions on here, which included downloading the cirrus logic audio driver and picking different models, as well as trying the snow leopard install disk driver for cirrus logic, and even tried installing the realtek analog driver. The closest I got to getting anything to work was installing the realtek analog driver. It installed fine up to the point when windows said "this driver is not tested, do you wish to install it anyway?" and I click yes, but then it pauses for a few seconds and the same message comes up again and repeats in a endless loop until you say "no, do not install driver" and then it does a uninstall of the driver.
Has anyone else experienced this problem and if so were you able to fix it?
Thanks
Message was edited by: What2be1

I found Gigabyte has links to latest updates which work fine.
Treat Mac Pro as just a dual Xeon PC.
http://forums.tweaktown.com/gigabyte/30530-latest-overclocking-programs-system-i nfo-benchmarking-stability-tools.html
Realtek High Definition Audio for Vista\Win 7 2.54
2010-11-05
Realtek HD Audio Windows 7
Or from Realtek which is http://218.210.127.131/
http://www.realtek-driver.com/
Guru3D is also a popular site for drivers.
http://downloads.guru3d.com/Realtek-HD-Audio-2.51_d2598.html
You can ignore USB audio, you want RealTek HD Audio. There are or can be some of those yellow alerts that are safe to ignore. Buried somewhere in Apple Support BootCamp technotes.
You can use installer from Realtek or zip file in which case just uncompress and update the driver from inside Device Manager. Nice thing, you can rollback a driver if you want to, or totally uninstall and then reinstall.

Device not work correctly

sometime USB port not work correctly, the device only flashes once and then off, the process of "system" increases the CPU to 100%. then I reboot and it works back

What do you mean "the measurement failed"
Can you please provide more details. Like an error code.

Problem using backup - one device not working.

Greetings,
I'm not able to use all backup devices. I made a backup using two dvd-r and one cd-r.
One of the dvds and the cd worked perfectly, but the second dvd does not work. There are no scratches or dust on the surface.
I tried both of my cd-drives.
What can I do?
Thanks in advance,
Schneesperling

use stystem recovery and lose all files, photos, games and all settings - that the best way ....
use device manager to reinstal sound driver, but try to install diferent versions of it, after update (made by hp update) i had no sound, installing older ver help
sorry for my poor english
Hp Pavilion dv6408nr - Vista
external HDD - ubuntu

Network adaters -BlackBerry Device not working in windows 8 when coinnected with usb cable

I was unable to find my plabook in the network or any mounted volume when I connect w8x64 pro to the playbook via usb cable despite the blackberry device manager is loaded on connection
in devce mgmt I found
Device Type: Network Adapters
Manufacturer: Research In Motion
location: 0000.001d.0007.005.000.000.000.000.000
Device Status:
This device is not working properly because Windows cannot load the drivers required for this device. (Code 31)
------------------- Events Tab--------::
Driver Management concluded the process to install driver rimpb_rndis.inf_amd64_c255bed1a35b762a\rimpb_rndis.inf for Device Instance ID USB\VID_0FCA&PID_8012&MI_00\6&1EDEAF40&0&0000 with the following status: 0x0.
Driver Management has concluded the process to add Service usb_rndisx for Device Instance ID USB\VID_0FCA&PID_8012&MI_00\6&1EDEAF40&0&0000 with the following status: 0.
Driver Management concluded the process to install driver rimpb_rndis.inf_amd64_e3f4ab2c803293ee\rimpb_rndis.inf for Device Instance ID USB\VID_0FCA&PID_8012&MI_00\6&1EDEAF40&0&0000 with the following status: 0x0.
Driver Management has concluded the process to add Service usb_rndisx for Device Instance ID USB\VID_0FCA&PID_8012&MI_00\6&1EDEAF40&0&0000 with the following status: 0.
Driver version: 2.0.0.32
Itried to update the device but it's up to date
what Can I do?

hi Suman Shrestha,
Welcome to the Lenovo Forums.
Your issue might be similar to this thread.
Although this is for a Windows 7 machine, can you try the solution that was posted and see if the problem gets fixed.
Let me know your findings
Cheers
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Satellite M50D-A : USB 3.0 devices not working in USB 3.0 ports

I can use 2.0 devices in the 3.0 ports fine, but my 3.0 device Flash Voyager USB3 8GB will not work. It connects then disconnects once, not showing up in device manager at all.
I've tried installing the USB driver off this site version 2.0.10.273-130101a for my model. That made no difference.
Install system Windows 8.1
Any ideas? Thanks.

The Voyager USB stick is manufactured by Corsair
I found in Corsair forum some threads and complaints about the troubles connecting the Voyager USB3.0 stick to USB 3.0 ports. Here the link the Corsair threads:
http://forum.corsair.com/v3/showthread.php?t=115891
http://forum.corsair.com/v3/showthread.php?t=111945
It looks like there are some compatibility problems between the USB controller (from AMD but _not_ Intel) and this USB stick.
One of the solutions could be the usage of other USB 3.0 flash memory sticks which are supported by AMD chipset.
You could also try to update the driver manually. You will need to check firstly the chipsets specs and name. To do that, I recommend you to install some kind of hardware diagnostic software (Everest Home Edit or Sandra Sisoft).
Then you could check on AMD page if an update for this chipset is available.

Help? Aggregate devices not working in Lion

Since buying a new Mac Mini Server for my audio work using Logic Pro 9 I cannot use aggregate devices. The system preferences as well as audio midi setup will not remember my aggregate devices that I create. Also when using them the audio becomes glitchy and a terrible noise happens. I didnt have any issues like this in 10.6.8. I cannot believe that Apple would let this happen for so long. There are many people in the pro audio world that rely on using aggregate devices and with them not working three versions into Lion this has become maddening.
This is not a third party issue. This is not a hardware issue. This is a serious problem that takes the saying that "Macs just WORK" and flushes it right down the toilet.
I spoke w a guy named Steve at Apple pro audio and he couldnt get me off the phone fast enough. What the ____ Apple??
PLEASE someone fix this? I wont try 10.7.4 as it seems to make Logic work even worse.
Please...I do not want to have to go back to using pro tools and PC's.

please and thanbk you Eriksimon! Full details - Mac Mini Server running Lion 10.7.3, Logic Pro 9.1.7 I use up to three Metric Halo 2882+DSP 2d units with the latest MIO console, drivers and firmware. Many other Metric Halo and other multiple device users are experiencing this and it is maddening. Ive been on Logic since 7 and am a analog-digital component level tech / electronics engineer / audio engineer with a decent knowledge of software.
I also use up to two McMix (now Avid artist mix) with latest version of Eucontrol as well as V-control pro with my iPad to control Logics transport etc when not in control room and a Novation sl49 compact USB keyboard with latest Automap version All that worked together quite well on 10.6.8 - logic 9.1.5 on my late 2008 Mac Book Pro but that system was slow...so I was hoping that Apple had Lion "in a cage" when I went out to buy this new Mac Mini Server.... I guess I should have waited.
I am having these aggregate device problems on a totally new from Mac Store Mac Mini Server Quad Core i7, did a clean install of Logic and the Metric Halo software /driver /firmware package.
Nothing else installed on this new Mac Mini but Logic 9.1.7 and MIO package.
Please....help get this bug fixed??
Best wishes dindisc2

MacBook Pro Retina USB 2.0 devices not working in right side USB port

4 days ago I bought MacBook Pro Retina 15".
When I plug USB 2.0 device to right side USB port, it does not work. OSX does not recognize it, iPhone does not charge, and so.
When I plug the same USB 2.0 device to left side USB port, it works.
When I plug USB 3.0 device to left or right side USB ports, it works without a problem.
Does anyone have this same issue? How did you resolve it?

I have a similar issue with a 13" Retina. Both my ports work OK for most USB devices but the right one won't work with a USB external HD (Time Machine backup). Very consistant.

Bluetooth and wireless device not working

Hi. My bluetooth is not appearing in my pc settings and has disappeared from device manager after i updated windows 8.1 recently. Also my wifi is not working. In pc settings, then network and in the flight mode section it says "we couldn't find wireless devices on this pc" under wireless devices. i tried updating the network adapter in device manager but in vain. Please help me. My laptop is hp 250 g3 core i5

Hi rohitraj_iit,
1. Check in the BIOS whether it's enabled.
2. Reinstall Hotkey features, restart your R400, press Fn+F5 -> Radio on the Bluetooth, thereafter reinstall the Bluetooth driver.
Let us know how it goes.
Maliha (I don't work for lenovo)
ThinkPads:- T400[Win 7], T60[Win 7], IBM 240[Win XP]
IdeaPad: U350
Apple:- Macbook Air [Snow Leopard]
Did someone help you today? Compliment them with a Kudos!
Was your question answered today? Mark it as an Accepted Solution!
Lenovo Deutsche Community Lenovo Comunidad en Español
Visit my YouTube Channel

Devices not working :/

Similar Messages

Maybe you are looking for