Dhcp and ethernet drivers

The normal "plumbing" for a STREAMS ethernet driver when configured is that it has open streams to the IP (sap 0x800) and ARP (sap 0x806) modules. For most drivers supporting fastpath, the IP stream's flags are set so that the fastpath optimizations are done.
It looks like things are slightly different if the ethernet driver is setup via dhcp (i.e. ifconfig driver0 dhcp). There are now two streams with sap 0x800, one with fastpath optimizations enabled, the other without. Presumably incoming IP packets should get sent up both these streams.
Can anyone confirm this? Can anyone explain why this is the case?
Thanks,
Chris

Update: I did a lot of reading and found that Appletalk is no more. I got a parallel to USB adaptor and connected the HP laserjet printer that way and it works fine. No more ethernet connection.
On my HP PSC 1350, I discovered since the OS up grade, I could not scan and the printer utility will not function. The only software HP has for this printer for Snow Leopard is PRINT ONLY. I did find software on Apple's site which I believe is for OS 10.7 and that works (sort of), Utility still won't work and the scan function is cumbersome to operate. It is disappointing that Apple and HP cannot be more in concert concerning up grades and keeping the ability to operate existing equipment. My next printer will be a Brother next time I need ink cartridges!!

Similar Messages

Airpirt and ethernet drivers

i recently put windows on my macbook via bootcamp and the wifi works wonderful in windows, but when i booted up in mac osx, airport will pick up the signal and then drop it. when it gets the signal, it is at full strength (i'm close to the router). it doesn't even get a signal through the ethernet port; it says it is plugged in but it doesn't have an ip adress, i've tried renewing the DHCP lease as well... i don't know what's wrong; i'm haveing to type this up on my friends desktop... grr.

Perhaps you mean the Satellite A305-S6857?
Satellite A305-S6857 PSAG0U Specifications
This unit is the Toshiba European version of the above model. It would appear to have a full set of Toshiba supplied XP drivers and utilities. Toshiba laptops are very finicky about using their own drivers, NOT the generic Windows ones, nor those directly from the chip maker.
Satellite A300-1J1 PSAG0E Specifications
Satellite A300-1J1 PSAG0E Downloads
The order of loading drivers and utilities is critical;
Drivers:
Chipset
Display
Sound
then all other drivers
Toshiba Utilities:
Common Module
Hotkey Utility
then all other Toshiba utilities
Good luck.
Mike

Hp 15-n200si usb drivers and ethernet control drivers not working windows 7 64bit

i recently changed from windows 8.1 to windows 7 64 bit and the drivers on the hp support site dont work for the ethernet control or usb driver were can i get working drivers??????

Hi:
See if these drivers work...
USB:
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-138111-1&cc=us&dlc=en&lc=en...
Ethernet:
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-137996-1&cc=us&dlc=en&lc=en...

I keep losing my Internet connection on my I mac osx 10.7.5 Wi fi and Ethernet. The only way to reconnect I'd renew dhcp but then it will disconnect again less then a minute

I keep losing my Internet on Wi fi and Ethernet, on Ethernet if I renew DHCP lease it will start again put within 20/30 seconds it disconnect again. My laptop , iPhone, iPad my other laptop all work with no problems, so it can't be the router any help please, my iMac is around 4 years old

Hi Ray, no idea what is mentioned in those other links, but...
this has worked for a few...
Make a New Location, Using network locations in Mac OS X ...
http://support.apple.com/kb/HT2712
10.7 & 10.8…
System Preferences>Network, top of window>Locations>Edit Locations, little plus icon, give it a name.
10.5.x/10.6.x/10.7.x instructions...
System Preferences>Network, click on the little gear at the bottom next to the + & - icons, (unlock lock first if locked), choose Set Service Order.
The interface that connects to the Internet should be dragged to the top of the list.
Is that Interface dragged to the top of Network>Show:>Network Port Configurations.
Instead of joining your Network from the list, click the WiFi icon at the top, and click join other network. Fill in everything as needed.
For 10.5/10.6, System Preferences>Network, unlock the lock if need be, highlight the Interface you use to connect to Internet, click on the advanced button, click on the DNS tab, click on the little plus icon, then add these numbers...
208.67.222.222
208.67.220.220
Click OK.

NForce ethernet drivers and buildin firewall

I have the 7030 board, and I have some problems with the nForce Ethernet drivers and buildin firewall.
When I try to update the Network access manager with the latest v5.10 driver pack from Nvidia I get the following error.
"1: The installscript engine on this machine is older then the version required to run this setup. If available, please install the latest version of ISSCRIPT.MSI, or contact your support personnel for further assistance."
then I get this error
"1603 fatal error during installation"
I followed this link and installed a patch "IsScript9.zip" that did not work. Hope someone has a sollution to this problem.
My other problem is with the firewall, when I try to change the firewall settings to any setting, I get this error "Error in FwlProfiles Set : Unable to find profile." and the firewall setting does not change.
Extra question, does the audio driver that comes with the Nvidia/nForce driver pack not work with the onboard sound card?
As an extra bonus, and to my amusement I cant search this forum I get THIS ERROR!
"Fatal error: Allowed memory size of 16777216 bytes exhausted (tried to allocate 35 bytes) in /var/www/web5/html/acp/lib/class_db_mysql.php on line 83"
Thank you for any help.

As a point of information, I also got that error message. To get it to work I had to uninstall the Nvidia Drivers, then I ran the isScript app, rebooted and re-installed the nforce drivers, it worked. On the manual installation, when you unzip the drivers to a location, make a note of the location. Then go into Device Manager, Network Adapters and Nvidia NForce. Locate the Update Driver tab and point to the location where you unzipped the files.

Has anyone else had problems with nForce ethernet drivers 3.13 and abo

Hi, I installed the previous version of the nForce unified drivers (2.03) and I have had problems with the latest version of the unified drivers also (2.41). These both have ethernet drivers "3.13 (WHQL) + TOT .NVU"
They seem to be the ethernet drivers fault. If I install one of the latest versions of the unified drivers, windows does not boot up, it just hangs at windows logo. ?(
If I remove the ethernet cards drivers using safe Mode, the system will boot up fine. I also have to re-install older versions of the ethernet drivers to get the system to boot.
I am using the K7N2 motherboard with onboard ethernet.
Any reasons/fixes would be great , cheers :]

falty mouse got a new one worked fin

S5503w win7 64bit ethernet and audio drivers

I recently acquired a Pavilion Slimline (s5503w) desktop PC. For whatever reason the hard drive was blanked out when I recieved it and upon installing Windows 7 64-bit (Ultimate Ed) I've had quite some time locating the proper drivers. Attempting to use the recommended drivers from this website resulted in a 9996 error, you don't meet the requirments. Proper recommended installer for that version of windows, but no luck. I've also tried installing the Ethernet and Audio drivers recommended by Nividia's website. A 15.49 package, but though it recognizes the video card it doesn't notice the onboard Ethernet or Audio. Neither of these devices is listed in device manager as far as I can tell either. No typical yellow exclemation mark stating that the driver is missing.
Any help or a point in the right direction would be greatly apperciated.

Hi:
I don't think there is anything wrong with the hardware.
I would reinstall W7.
Then right afterward, install that nForce chipset driver first and reboot.
Then the video driver I posted and reboot.
Then the audio driver I posted and reboot.
If you still have issues, try a manual install.
Download the free 7-zip file utility and extract the files you downloaded into folders.
Then click on each device in the device manager that needs the drivers.
Click on the driver tab, click on update driver, select the Browse my computer for software and browse to the folders you extracted for each device.
Make sure the Include Subfolders box is checked and see if the drivers install that way.
There has to be a way to get these items installed.
If you stil can't get the drivers installed, please post the hardware ID's for each device needing drivers so I can confirm that they are what they are supposed to be according to the product specs for your PC.
If you don't know where to find the hardware ID, please read the info at the link below.
http://www.devicedriverfinder.com/blog/device-drivers/how-to-check-the-hardware-id-for-a-windows-dev...

Tecra M2 PTM20A-002T2 - Need ethernet and display drivers

Please help me with an answer!
I have spent hours chasing files and installing different stuff.
Got my sound working but still need ethernet and display drivers I think.
I am online for about 15 minutes and back on tonight.
Thanks, Nay,
Melbourne, Australia

Hi Nay,
Alternative have a look on the Toshiba European page. There I founded a similar model, Tecra M2 PTM20E, and I think the downloads should also work for your model:
http://eu.computers.toshiba-europe.com > Support & Downloads > Download Drivers
Furthermore you can see an installation instructions document for Windows XP. Its a list for the recommend driver installation order, tested by Toshiba. :)
Last but not least you can identify the hardware using hardware and vendor ID. Therefore check this article:
[How to identify an unknown device (e.g. Wireless LAN module)?|http://aps2.toshiba-tro.de/kb0/HTD0302U00000R01.htm]

Will Timecapsule do DHCP via air and ethernet simultaneously?

Will Timecapsule do DHCP via air and ethernet simultaneously?
I want to use it as a router for a home network for both wired and wireless with one public DHCP adress from my ISP.
Can I?
Thanx and regards

I use a Mac Pro wired and a Mackbook wireless using TC as the router. Yes.

Dhcp and pcmcia NIC startup (SOLVED)

Hello;
I'm pretty impressed with Arch up to now, but am having a problem with the pcmcia NIC. I'm sure it's some simple config problem, but I haven't been able to figure it out.
I'm using a Network Everywhere NP100, which uses the axnet driver. No problems there. I have it set as eth0="dhcp".
It works fine, but when I restart the box, or start up from a cold start, dhcp isn't assigning an IP, and during boot, network fails on start. After the box is up and running, I have to remove the card from the slot and reinsert it to get dhcp to assign an IP.
I haven't seen this problem with other distros, so I know it can be fixed, not not sure how. Below is my rc.conf, maybe somebody can spot something I'm missing?
HARDWARECLOCK="UTC"
TIMEZONE=EST5EDT
KEYMAP=us
CONSOLEFONT=
USECOLOR="yes"
# Scan for LVM volume groups at startup, required if you use LVM
USELVM="no"
# Networking
HOSTNAME="Arch-laptop"
# Module to load at boot-up (in this order)
# (prefix a module with a ! to disable it)
MODULES=(!usbserial !ide-scsi snd-es1968 yenta-socket pcmcia ohci_hcd ehci_hcd pcspkr parport_pc parport irtty_sir sir_dev irda crc_ccitt i2c_piix4 i2c_core uhci_hcd usbcore tsdev evdev rsrc_nonstatic pcmcia_core snd_ac97_codec snd_pcm_oss snd_mixer_oss snd_pcm snd_timer snd_page_alloc gameport snd_mpu401_uart snd_rawmidi snd_seq_device snd soundcore rtc)
# Interfaces to start at boot-up (in this order)
# Declare each interface then list in INTERFACES
# (prefix an interface in INTERFACES with a ! to disable it)
# Note: to use DHCP, set your interface to be "dhcp" (eth0="dhcp")
lo="lo 127.0.0.1"
eth0="dhcp"
INTERFACES=(lo eth0)
# Routes to start at boot-up (in this order)
# Declare each route then list in ROUTES
# (prefix a route in ROUTES with a ! to disable it)
gateway="default gw 192.168.0.1"
ROUTES=(!gateway)
# Daemons to start at boot-up (in this order)
# (prefix a daemon with a ! to disable it)
DAEMONS=(dbus hal pcmcia syslog-ng crond network !netfs !hotplug)
# End of file
Any suggestions would be appreciated.

# When you boot the machine the first time it is just fine?
No it has this problem every time the machine is started.
# Do you really have to remove the card from the slot, isn't 'cardctl eject' enough?
Removing and reinserting the card is faster than typing out a command so that's what I do.
# Does it work with static IP?
Don't know, router is set up as DHCP and haven't tried changing it to static. As it's a mobile machine, I'd prefer it works using dhcp.
# Does your machine own another nic, so the race who will become eth0 could be won by an ethernet card?
No, I just have the one NIC at the moment. I have a wireless pcmcia NIC as well, but haven't installed/configured it yet as I don't use it much and would like to solve this ethernet problem first.
#By the way, which kernel modules own the axnet drivers?I can't see any matching module in rc.conf's modules section, and you have hotplug disabled.
It's owned by pcmcia, which loads the module itself when the card is detected. This is working perfectly and the driver modules loads no problem. As far as I can tell the problem seems to be with the network daemon itself, but I could be mistaken about this.
I disabled hotplug for the moment while I try to figure this out. At first I thought hotplug was the culprit but even with it disabled the problem remains. I just haven't bothered to re-enable hotplug as I already have all the modules loading through rc.conf anyway and it speeds up booting.
Hope the additional info may help figure this out. I'm stumped.

Apple Airport Extreme Base Station for PPPoE, DHCP and NAT with ActionTec DSL modem

I just spent several hours trying to track down proper instructions for setting up my Apple AEBS to do the PPPoE, DHCP and NAT while connected to an ActionTec M1000 (no wireless module). It turns out my initial set ups on both devices were correct, but that the order for rebooting and reconnecting the two devices is critical. All of the threads I found on this forum and on many others suggested this was not possible, but it is. What I don't yet know is whether it is the best method for running my home network DSL connection to my ISP (CenturyLink).
The instructions I found that worked come courtesy of Brandon Konkle's blog and are both simple and clear: http://brandon.konkle.us/post/19637529637/centurylink-actiontec-q1000-airport-ex treme-bridge
The proper settings for the ActionTec DSL Modem can be found under Advanced Setup/IP Adressing/WAN IP Address
Click RFC 1483 Transparent Bridging then click on Apply.
(see also http://qwest.centurylink.com/internethelp/modems/m1000/pdf/M1000_BRIDGE.pdf )
To reduce time, do this BEFORE you reset your AEBS then set the AEBS so that you don't have to wait for the AEBS to reboot.
In contrast to what Brandon described for the Q1000 modem, my AEBS never reconnected to the modem (he describes his as getting an IP from his ISP, then dropping it then getting another over and over - mine never got an IP). Once you have reset both devices as described, the critical steps I have not found described elsewhere were:
1. Disconnect the power from both the modem and the Airport Extreme.
2. Disconnect the Ethernet cable between the two devices
3. Restore power to the 2 devices and allow them to fully reboot. For the ActionTec M1000, this is indicated when the lights stop blinking. (Note that the Internet light will NOT be lit in this instance since the modem is acting only as a bridge. You will NOT have an Internet connection until the AEBS is reconnected.) The AEBS will be blinking yellow.
4. Reconnect the Ethernet cable between the devices (make sure on the M1000 that you are using the connector with the circle icon over it, not the arrow icon).
Within about 60 seconds, the AEBS light went to steady green and the connection to the Internet was restored.
Now I have to see if this is a more stable configuration than the flaky one I had before while using the AEBS as a bridge and the M1000 to do everything.
Does anyone think or know if it will make a difference?
Message was edited by: Bud Shaw

Now I have to see if this is a more stable configuration than the flaky one I had before while using the AEBS as a bridge and the M1000 to do everything.
Does anyone think or know if it will make a difference?
No one can accurately predict in advance what the actual results might be. I've tried both ways with different products and cannot say that one method is better than the other. What works is best.
In theory, it is preferable to have the modem provide the PPPoE connection service since it is the device connected directly to the Internet.
In practice, results vary depending on the service provider, products used, phase of the moon, alignment of the planets, etc.

New MacBook Pro 10.7.2 trying to connect to HP laserjet 1200 w wireless. Tried generic driver and hpdriver and gutenprint drivers. "Unable to connect due to error". Deleted prefs, restarted etc. Any ideas ?

Just purchased a MacBook Pro OS 10.7.2. Cannot get it to print with HP LaserJet 1200.
Connection is wireless, able to ping printer. (also tried MacBook using ethernet).
This HP 1200 prints perfectly with another mac running Snow Leopard.
Tried HP 1200 driver, which, according to HP, is not working with 10.7.2; They suggested Gutenprint
tried generic printer from Mac, (message was printer is busy);
tried CUPS Gutenprint 5.0.2,(message says "unable to connect due to an error"
removed preferences and re-added printer, rebooted etc.
Any thoughts? I thought it was the driver, maybe there are other drivers out there or maybe it's something else???? Thanks

Thanks for the replys.
After spending an hour plus, uninstalling and reinstalling drivers and still not able to print, my husband, sits down, plugs in an ethernet cable, reinstalls the printer with the ip, and it prints. !!! I'd already done that , but that was before I deleted the preferences and installed the Gutenprint driver. I think it was the new Gutenprint driver that did it.

How to set up DHCP and NAT for QNAP NAS MyCloud service?

I have an Apple AirPort Extreme Base Station (AEBS) attached to my DSL model (no router in the modem). My QNAP NAS is attached via ethernet to the QNAP NAS. My iMac (running AirPort Utility 6.x) is connected to the AEBS via wifi.
I've found several folks who've tried this (and apparently succeeded) but I'm a networking novice and am having trouble making this work. What I did was to go into the AirPort utility and in the networking section configure "DHCP and NAT" and then called out the static IP and MAC address of the QNAP NAS (as well as the ports I'd like to remain open). However, when I did this and applied the changes, my iMac (connected to the AEBS via wifi) could no longer see the AEBS, which then required me to reset the AEBS, re-configure it back to the previous known good conifiguration and start over. After about 5 cycles of this I gave up.
So, what am I doing wrong here? Do I need to go in and configure every device that is going to access the AEBS as static and call out each device's IP and MAC address? (hopefully not, that'd be a major PITA).
Help. Anyone?

When I run diagnostics with the QNAP, here is the reply I get (IPs redacted):
------ NAT PMP Diagnostics ------
initnatpmp() returned 0 (SUCCESS)
using gateway : xx.x.x.x
sendpublicaddressrequest returned 2 (SUCCESS)
readnatpmpresponseorretry returned 0 (OK)
Public IP address : 192.168.xxx.xxx
epoch = 2621
closenatpmp() returned 0 (SUCCESS)
------ UPnP Diagnostics ------
upnpc : miniupnpc library test client. (c) 2006-2011 Thomas Bernard
Go to http://miniupnp.free.fr/ or http://miniupnp.tuxfamily.org/
for more information.
List of UPNP devices found on the network :
desc: http://xx.x.x.x:60606/8CC1212D0C6D/Server0/ddd
st: upnp:rootdevice
desc: http://xx.x.x.x:9000/TMSDeviceDescription.xml
st: upnp:rootdevice
desc: http://xx.x.x.xx:55000/nrc/ddd.xml
st: upnp:rootdevice
desc: http://xx.x.x.xx:55000/dmr/ddd.xml
st: upnp:rootdevice
desc: http://xx.x.x.xx:49152/4/description.xml
st: upnp:rootdevice
desc: http://xx.x.x.xx:49152/2/description.xml
st: upnp:rootdevice
desc: http://xx.x.x.xx:49152/0/description.xml
st: upnp:rootdevice
desc: http://xx.x.x.xxx:8200/rootDesc.xml
st: upnp:rootdevice
desc: http://xx.x.x.xxx:49152/gatedesc.xml
st: upnp:rootdevice
desc: http://xx.x.x.xxx:49153/gatedesc.xml
st: upnp:rootdevice
desc: http://xx.x.x.xxx:49155/gatedesc.xml
st: upnp:rootdevice
desc: http://xx.x.x.xxx:9000/TMSDeviceDescription.xml
st: upnp:rootdevice
UPnP device found. Is it an IGD ? : http://xx.x.x.x:60606/
Trying to continue anyway
Local LAN ip address : xx.x.x.xxx
GetConnectionTypeInfo failed.
Status : , uptime=3217870016s, LastConnectionError :
Time started : Wed Mar 13 17:04:03 1912
MaxBitRateDown : 7 bps MaxBitRateUp 0 bps
GetExternalIPAddress() returned -3
GetExternalIPAddress failed.
GetGenericPortMappingEntry() returned -3 ((null))

I can't find My CQ60-215EE Sound and Ethernet XP SP2 driver. any help!

I downgraded my oprating system to XP I found all drivers accept sound and ethernet, can any body help me
This question was solved.
View Solution.

Hi,
MS-UAA (required with a reboot before Audio driver) here
Conexant HD Audio here
Realtek RTL8101E Family PCI-E Fast Ethernet NIC Driver here
** Say thanks by clicking the "Thumb up" icon which is on the left. **
** Make it easier for other people to find solutions, by marking my answer with "Accept as Solution" if it solves your issue. **

MB Air cannot see TC 1T '09 while connected via WiFi and Ethernet.

I have a TC 1T 2009 7.4.1 that I have set up successfully with MB Pro and MB White. However I cannot set it up with MB Air v.1 which is connected to TC via WiFi AND Ethernet cable. Internet is fine (Safari) but no TM - when I run APU 5.4.1 it cannot discover the TC it is connected to.
I tried connecting after hard-reset (poke/power on), it would see the TM but then hang forever reading the configuration. So I set it up with MB Pro and MB White and both are now working fine with TC/TM. Then I tried MB Air and it failed.
The TC is connected via ethernet to Sagem router (bridged mode) which supplies WAN and DHCP, it has its own WiFi as well.

And by the way, Hi Everyone, how rude of me not to greet you in the post.
Thanks for any help!

Dhcp and ethernet drivers

Similar Messages

Maybe you are looking for