DHCP Error with WLC 2504 and Aironet 2600 setup across subnets

Hey guys
I have just setup a new WLC 2504 controller to manage a WiFi service that will span 6 geographic locations. The local networks at each location are on different subnets (all 192.168.x.x) and are linked up via IPSEC VPN links, and there is Active Directory spanning the sites, with DNS and DHCP servers running at each location.
I tested the WLC at our main office with a single AP, and it worked fine. The AP set itself up, and wireless devices connect with no probs. Great! Yesterday I headed out to one of our remote sites, and connected an AP to their network - and that seemed to work fine too. Within a few minutes I was able to see the WiFi network I'd setup, and my smartphone connected to it straight away (as I'd rpeviously connected at the main office), so I was pretty happy that all was working well.
This morning however I've had notification that wifi performance at the remote site isn't great. I've got someone to check their ip address, and I've found that their IP address and default gateway match the LAN at the main office where the WLC is based - NOT the LAN where the wireless client is. Obvioulsy this is not ideal!
So I guess my question is, what have I done wrong? (I guess I HAVE done something wrong!?). And how can I get wireless clients at remote sites to pick up an IP from the DHCP server at THEIR site?
Any help would be greatly appreciated!
Thanks!

Hello Tim,
What mode your APs are in? Local mode? or FlexConnect mode?
If local mode, then all the traffic will be tunnelled to the WLC and they'll be same as if you are connecting from the WLC location.
If you use FlexConnect APs (which is recommended for remote sites) you can configure FlexConnect groups on the WLC and add each location in a specific group. In that group you can decide what VLAN the users should be in.
Check this link for FlexConnect group configuration
http://www.cisco.com/en/US/docs/wireless/controller/7.2/configuration/guide/cg_flexconnect.html#wp1230080
HTH
Amjad
Rating useful replies is more useful than saying "Thank you"

Similar Messages

Dynamic VLAN Assignment with RADIUS Server and Aironet Access Points

Hi Guys,
I would like to go for "Dynamic VLAN Assignment with RADIUS Server and Aironet Access Points 1300". I want the AP to broadcast only 1 SSID. The client find the SSID ->put in his user credential->Raudius athentication->assign him to an specific vlan based on his groupship.
The problem here is that I don't have a AP controller but only configurable Aironet Access Points 1300. I can connect to the radius server, but I am not sure how to confirgure the AP's port, radio port, vlan and SSID.
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008076317c.shtml#switch
I go through some references:
3.5 RADIUS-Based VLAN Access Control
As discussed earlier, each SSID is mapped to a default VLAN-ID on the wired side. The IT administrator may wish to impose back end (such as RADIUS)-based VLAN access control using 802.1X or MAC address authentication mechanisms. For example, if the WLAN is set up such that all VLANs use 802.1X and similar encryption mechanisms for WLAN user access, then a user can "hop" from one VLAN to another by simply changing the SSID and successfully authenticating to the access point (using 802.1X). This may not be preferred if the WLAN user is confined to a particular VLAN.
There are two different ways to implement RADIUS-based VLAN access control features:
1. RADIUS-based SSID access control: Upon successful 802.1X or MAC address authentication, the RADIUS server passes back the allowed SSID list for the WLAN user to the access point or bridge. If the user used an SSID on the allowed SSID list, then the user is allowed to associate to the WLAN. Otherwise, the user is disassociated from the access point or bridge.
2. RADIUS-based VLAN assignment: Upon successful 802.1X or MAC address authentication, the RADIUS server assigns the user to a predetermined VLAN-ID on the wired side. The SSID used for WLAN access doesn't matter because the user is always assigned to this predetermined VLAN-ID.
extract from: Wireless Virtual LAN Deployment Guide
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00801444a1.html
==============================================================
Dynamic VLAN Assignment with RADIUS Server and Wireless LAN Controller Configuration Example
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008076317c.shtml#switch
==============================================================
Controller: Wireless Domain Services Configuration
http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_configuration_example09186a00801c951f.shtml
Any help on this issue is appreicated.
Thanks.

I'm not sure if the Autonomous APs have the option for AAA Override. On the WLC, I can go into the BSSID, Security, Advanced, and there's a checkbox that I would check to allow a Radius server to send back the VLAN.
I did a little research and it looks like the 1300 may give this option but instead is defined as "VLAN Override". I've found the release notes for 12.3(7)JA5 (not sure what version you're running) that give mention and a link to configuring EAP on page 4: http://www.ciscosystems.ch/en/US/docs/wireless/access_point/1300/release/notes/o37ja5rn.pdf
Hope this helps

Best practices for network design on WLC 2504 and 5508

Dear all:
I'm looking for some recommendations on WLC 2504 and 5508 about the the following:
Maximum amount of AP per port
The scenario when to use all ports in both WLC
Maximum number of clients(users) per port
Bandwidth comsumption of management vs data in order to assign one port for management
I've just found this:
Cisco 5508 controllers have eight Gigabit Ethernet distribution system ports, through which the controller can manage multiple access points. The 5508-12, 5508-25, 5508-50, 5508-100, and 5508-250 models allow a total of 12, 25, 50, 100, or 250 access points to join the controller. Cisco 5508 controllers have no restrictions on the number of access points per port. However, Cisco recommends using link aggregation (LAG) or configuring dynamic AP-manager interfaces on each Gigabit Ethernet port to automatically balance the load. If more than 100 access points are connected to the 5500 series controller, make sure that more than one gigabit Ethernet interface is connected to the upstream switch.
http://www.cisco.com/c/en/us/td/docs/wireless/controller/6-0/configuration/guide/Controller60CG/c60mint.html
Thanks for your help.

The 5508-12, 5508-25, 5508-50, 5508-100, and 5508-250 models allow a total of 12, 25, 50, 100, or 250 access points to join the controller.
This is an old document. 5508 can now support up to 500 APs if you run firmware 7.X. 2504 can support up to 75 APs if you run firmware 7.4.X.
I'm looking for some recommendations on WLC 2504 and 5508 about the the following:
Best practice and recommendation is to LAG all ports so you will be able to form a link redundancy. If one link goes down, you have other link to push traffic.

An issue with WLC 5508 and 7921 phone

Hello all!
I have a system with WLC 5508 and some 1242 APs. And I use a lot of 7921 phones.
One of 7921 phones was in trouble. It loses registration, disconnect conversations...
I installed the trial WLC and run voice diagnostics.
I saw some of "Potentially degraded QoS in downlink direction because of incorrect packet classification" messages and one "Fair upstream packet loss ratio: 1,2%, which is less than threshold 2.5%"
As I understand all of 7921 phones in these area are affected.
what does it mean? I set up Platinum QoS for voice WLAN. I don't have any qos configuration string for AP and WLC ports on switches...
any ideas?
thanx in advance

Sergey:
There is one application called "WLC Config analyzer". You save your "show run-config" from your WLC in a text file and import it by this application. it will analyze the file for you and tell you what recommendations for voice are missing so you improve them.
When importing a config file you choose what voice clinets you are using, so you need to choose cisco 7921 to it tells you what config improvemetns is needed based on 7921 needs.
Here is the link to download the application:
https://supportforums.cisco.com/docs/DOC-1373
download the latest versoin.
BTW, how many voice/data clients are connected to one AP in that area? if I remember correctly if you are utilizing voice then the max number of clients connected to one AP should not exceed 17. If you have more than this number per AP try to minimize the number of users concurrently connected to the AP then try again.
Hope you'll find the config analyzer useful.
If useful please don't forget to rate.
Amjad

Cisco WLC 2504 and ways to authenticate users

Hi All,
What is the ways to make user authenticate to WLC 2504 and what is the best and simple way and what is the differences btw each method _i mean for example need radius server or something else to be exist_ ?
and any one can give me case study for this issue
System consist of Cisco 2504 and Cisco LAP 1140
Thanks

To implement radius based authentication is the best practice for the small & enterprise environment.
Information About RADIUS
Remote Authentication Dial-In User Service (RADIUS) is a client/server protocol that provides centralized security for users attempting to gain management access to a network. It serves as a backend database similar to local and TACACS+ and provides authentication and accounting services:
•Authentication—The process of verifying users when they attempt to log into the controller.
Users must enter a valid username and password in order for the controller to authenticate users to the RADIUS server. If multiple databases are configured, you can specify the sequence in which the backend database must be tired.
•Accounting—The process of recording user actions and changes.
Whenever a user successfully executes an action, the RADIUS accounting server logs the changed attributes, the user ID of the person who made the change, the remote host where the user is logged in, the date and time when the command was executed, the authorization level of the user, and a description of the action performed and the values provided. If the RADIUS accounting server becomes unreachable, users are able to continue their sessions uninterrupted.
RADIUS uses User Datagram Protocol (UDP) for its transport. It maintains a database and listens on UDP port 1812 for incoming authentication requests and UDP port 1813 for incoming accounting requests. The controller, which requires access control, acts as the client and requests AAA services from the server. The traffic between the controller and the server is encrypted by an algorithm defined in the protocol and a shared secret key configured on both devices.
You can configure multiple RADIUS accounting and authentication servers.For example, you may want to have one central RADIUS authentication server but several RADIUS accounting servers in different regions. If you configure multiple servers of the same type and the first one fails or becomes unreachable, the controller automatically tries the second one, then the third one if necessary, and so on.
For more Information : http://www.cisco.com/en/US/docs/wireless/controller/7.2/configuration/guide/cg_security_sol.html#wp2149947

I am unable to burn any info-photo ect on to a disk. I have a 27" I mac mid 2010 version. I put in a disk, hit burn, it runs for about 3 mins and ejects the disk sayiny there was an error with the drive and will not restart.

am unable to burn any info-photo ect on to a disk. I have a 27" I mac mid 2010 version. I put in a disk, hit burn, it runs for about 3 mins and ejects the disk sayiny there was an error with the drive and will not restart.

The optical drive has probably failed. It's a fairly common thing with these slim SuperDrives. Does it read any discs you put into it? You can try resetting the SMC and pram but I'll be surprised if it helps.
To reset the SMC
Shut down the computer.
Unplug the computer's power cord.
Wait fifteen seconds.
Attach the computer's power cord.
Wait five seconds, then press the power button to turn on
Resetting PRAM and NVRAM
Shut down the computer.
Locate the following keys on the keyboard: Command, Option, P, and R. You will need to hold these keys down simultaneously in step 4.
Turn on the computer.
Press and hold the Command-Option-P-R keys. You must press this key combination before the gray screen appears.
Hold the keys down until the computer restarts and you hear the startup sound for the second time.
Release the keys.

I was downloading the software update for ipod touch 2gen and after it was done downloading it showed that there was an error with my ipod and when i saw it was on the lockscreen loading. its been like this for 4 hours already

I was downloading the software update for ipod touch 2gen and after it was done downloading it showed that there was an error with my ipod and when i saw it was on the lockscreen loading. its been like this for 4 hours already

What did the error message say?
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

Guest wireless with WLC 2504, Catalyst 4510R+E and ASA 5510

I need to add guest (internet only) wireless to our existing internal wireless and am looking for advice as to the best practice configuration. Existing infrastructure as follows:
WLC 2504
1142 LAPs
4510R+E
ASA 5510
Existing configuration as follows:
WLC management interface and APs addressed on the 192.168.126.0 /25 network
Internal WLAN mapped to the management interface
Management interface VLAN ID 0 (untagged) and dynamic AP management enabled
WLC port 1 (only) connected to 4510 via trunk with native VLAN set to 7 and allowed VLAN set to 7
4510 connected to ASA inside interface (security level 100)
Switchport on 4510 connected to ASA configured as switchport access VLAN 99 (our internet VLAN)
ASA inside interface NOT configured for subinterfaces and is addressed on the 192.168.121.0 /25 network
What is the best way to add guest wireless to our existing configuration?
Note: I need the guest wireless to be filtered by Websense as our internal wireless is
Any advice would be greatly appreciated!

Thank for the reply Scott. The configuration recommendations from Yahya did not work. I set up as he recommended and also added a dhcp scope on the wlc. Client gets dhcp but cannot even ping the wlc much less anything else. Yahya stated above to configure port 2 on the wlc to an access port on my 4510. Aren't all connections from the wlc supposed to be trunk links to the switch? Shouldn't I just leave the management interface on the wlc untagged and add a dynamic interface for each wlan and tag it with the approriate vlan id? And then leave the (one) physical connection on the wlc (port 1) connected to a trunk link on the 4510 that allows the required vlans?
Any input would be greatly appreciated...
JW

Error with "Sync calendar and tasks" - Nokia 6500c

I'm having trouble with "Sync calendar and tasks" - all other sync is fine.
It all worked OK with PC Suite beforehand.
I've auto upgraded to Ovi on last connection.
Can anyone help?
Error message when trying to sync is:
"Not enough space in device
First remove some files from your device and then sync again.
8393f01e"
Phone status:
Device memory - 910MB of 940MB fee
Phone version:
Nokia 6500c
V 09.48
26-01-09
RM-265
Ovi version:
Nokia Ovi Suite 2.0.1.35
Nokia PC Suite 7.1.40.1
Nokia Music 1.3.20722.1
PC Connectivity Solution 9.44.0.3
Connectivity Cable Driver 7.1.22.0
Nokia Ovi Suite Software Updater 2009.40.0.60128
Maps Service API 3.0.35.0
Nokia Platform 2.5.195
Ovi Desktop Sync Engine 1.0.0.684
Operating system:
Microsoft Windows XP 32-bit Edition, Service Pack 3
Language: English
Detected internet browsers:
- Microsoft Internet Explorer 6.0.2900.5512
- Mozilla Firefox 3.5.5
Detected Bluetooth stacks:
- Microsoft (Version: 5.1.2600, Build: 5512)
- Toshiba (Version v4.00.22(D))
Thanks.
Cheers,
Jason.

Hi,
Really **bleep** off with this issue in synchronizing , I move back to my old PC suite that worked fine .
I expect our NOKIA provider to be back on their code and solve this issue.
At least, one mail to me warning me of corrections with this issue and improved performances would not be considered by me as spam but as consideration to users .
Sorry dear developpers but either your specs were uncomplete, at least performance criterias were undefined and you businees acceptance test were unproperly managed. I would not like to be the project manager in charge of ! Just before Christmas, providing such a release will make Santa Klaus quite unhappy top him .
BR

Graphic problems/errors with Mainstage 3 and MBP (15'' 2011)

Hi,
I bought Mainstage 3 for my MBP (15'' 2011).
When i click con "perform" i get graphic errors.
I have the same issue with the old Mainstage version since Mountain Lion.
Also a fresh installation didn't help.
I think i'm not the only one with this issue!
I don't know how to report a bug?
Perhaps someone can help me.
(and I'm probably not the only one (see feedback in Apple Store) If you also have this problem, please add a comment with your configuration (Hardware, Software))
/forgotten ebi
So, here an example how it looks like when i click on "perform":

Same configuration,same problem. BUT I found a workaround.
Mainstage has this error with the AMD video card and/or a second monitor connected.
With a little app (http://gfx.io) it's possible to really force the MBPro to use the Intel Graphics card.
This will work only with the internal screen, not with a second screen connected.
And sometimes you need to restart, to really make the Intel video card free.
This works fine...In the meantime of a fix.

Tips for blue screen (BSOD) errors with Windows Vista and Intel Turbo Memory on T61/T61p

Important note: The symptoms and solutions described below address only a small subset of the possible causes for blue screen errors, aka BSOD. This information can help address blue screen errors specifically related to Turbo Memory, but may not solve errors related to other issues. Please read through the instructions completely, make sure they apply to your system, and after attempting the solutions please post back with your feedback for the community.
Some users may experience random blue screen errors with ThinkPad
systems running Windows Vista with Intel Turbo Memory hardware. These
blue screens may occur during normal usage on the system or they may
occur when booting into Windows Vista. Blue screens related to the
Intel Turbo Memory hardware may reference a stop code of 8086 with
memory address locations of {0, 0, 0, 0}.
There are two main steps that you can take to help resolve blue screen issues related to Intel Turbo Memory.
Step 1: Update Intel Turbo Memory Driver
If the driver version is before version 1.0.1.1004-7.0.3.1001, please
update to this version.
To determine what version of the Intel Turbo Memory driver is installed:
1.    Click Start, then click Control Panel.
2.    Click System and Maintenance.
3.    Click System.
4.    Click Device Manager.
5.    Expand the Storage controllers category.
6.    Double-click Intel Flash Cache Logic Chip.
7.    Click the Driver tab. Then you will see the driver version (for example, 1.0.1.1004).
The new driver and installation instructions can be found here.
Note: The Intel Matrix Storage Driver is updated with this package.
Step 2: BIOS version
If your BIOS version is older than those listed below, please update to the version listed.
How to check your BIOS version:
Turn off the system.
Turn on the system.
While the To interrupt normal startup, press the blue ThinkVantage button message is displayed at the lower-left area of the screen, press the F1 key.
The
BIOS Setup Utility menu will be displayed. If you have set a supervisor
password, the BIOS Setup Utility menu appears after you enter the
password.
Check BIOS Version and Embedded Controller Version.
Turn off the system.
System BIOS versions:
ThinkPad T61/T61p (14.1 inch widescreen with IEEE 1394 model) - BIOS version 1.22 (7LET52WW)
Please
remember that these updates do not solve every possible system blue
screen, but they do resolve several problems related to the Intel Turbo
Memory driver.
Message Edited by Tim_Lenovo on 11-30-2007 07:03 PM
Tim Supples
Lenovo Social Media
Got a question? Don't PM me, post it on the forum!
Lenovo Blogs
X60 Tablet SXGA+ primary, Z61p fully loaded workhorse

Thanks Tim,
I do have my T61p fully up-to-date to the latest drivers and updates (via System Update and the Drivers&Software web page when the former is not that up-to-date).
At the moment the most recurrent problem is this:
http://forum.lenovo.com/lnv/board/message?board.id=T_Series_Thinkpads&thread.id=55
which has been longly speculated here:
http://forum.thinkpads.com/viewtopic.php?t=47755
My other angst is the boot-time chkdsk hang-up problem:
http://forum.thinkpads.com/viewtopic.php?t=52765&highlight=chkdsk
I just wonder if this purely a Vista issue when using NV cache, the disk spinning down at almost exactly 1 hour from the beginning of the chdsk operation seems too much of a coincidence.
This is my T61p configuration:
Intel Core 2 Duo T7700 2.4GHz
BIOS version 1.26-1.06
4GB RAM 2 SO-DIMMs
nVidia Quadro FX 570m with 512MB VRAM
WUXGA LCD
Seagate 7200.2 160 GB
4GB RAM 2 SO-DIMMs
Windows Vista Ultimate 32bit (waiting to move to 64bit)
thanks,
andrea
Message Edited by abarbieri on 12-05-2007 03:48 PM
T61p - 15.4" - T7700 - FX 570M 256MB - 4GB RAM - ST916023AS - 4965AGN - BT - FPR - 9 cell - Vista Ult. x86
T21p - 14" - PIII 850MHz - S3 Savage/IX 8MB - 512MB RAM - 100GB 7200rpm - WinXP x86

Tips for blue screen (BSOD) errors with Windows Vista and Intel Turbo Memory on X61/X61s

Important note: The symptoms and solutions described below address only a small subset of the possible causes for blue screen errors, aka BSOD.
This information can help address blue screen errors specifically
related to Turbo Memory, but may not solve errors related to other
issues. Please read through the instructions completely, make sure they
apply to your system, and after attempting the solutions please post
back with your feedback for the community.
Some users may experience random blue screen errors with ThinkPad
systems running Windows Vista with Intel Turbo Memory hardware. These
blue screens may occur during normal usage on the system or they may
occur when booting into Windows Vista. Blue screens related to the
Intel Turbo Memory hardware may reference a stop code of 8086 with
memory address locations of {0, 0, 0, 0}.
There are two main steps that you can take to help resolve blue screen issues related to Intel Turbo Memory.
Step 1: Update Intel Turbo Memory Driver
If the driver version is before version 1.0.1.1004-7.0.3.1001, please
update to this version.
To determine what version of the Intel Turbo Memory driver is installed:
1.    Click Start, then click Control Panel.
2.    Click System and Maintenance.
3.    Click System.
4.    Click Device Manager.
5.    Expand the Storage controllers category.
6.    Double-click Intel Flash Cache Logic Chip.
7.    Click the Driver tab. Then you will see the driver version (for example, 1.0.1.1004).
The new driver and installation instructions can be found here.
Note: The Intel Matrix Storage Driver is updated with this package.
Step 2: BIOS version
If your BIOS version is older than those listed below, please update to the version listed.
How to check your BIOS version:
Turn off the system.
Turn on the system.
While the To interrupt normal startup, press the blue ThinkVantage button message is displayed at the lower-left area of the screen, press the F1 key.
The
BIOS Setup Utility menu will be displayed. If you have set a supervisor
password, the BIOS Setup Utility menu appears after you enter the
password.
Check BIOS Version and Embedded Controller Version.
Turn off the system.
System BIOS versions:
ThinkPad X61 or X61s - BIOS version 1.06 (7NET25WW)
Please
remember that these updates do not solve every possible system blue
screen, but they do resolve several problems related to the Intel Turbo
Memory driver.
Tim Supples
Lenovo Social Media
Got a question? Don't PM me, post it on the forum!
Lenovo Blogs
X60 Tablet SXGA+ primary, Z61p fully loaded workhorse

Dear Tim,
First off, many thanks for the tips for resolving BSOD with Vista + Turbo Memory on X61. I've been suffering from this BSOD for countless times since I bought in my X61 7673-CW9 in April 2008.
Even prior to having the pleasure to visit this wonderful forum, I followed both steps as indicated, and updated my Intel Turbo Memory driver to 1.5.0.1013 and my BIOS to 7NETB4WW (2.14). However, the BSOD recurrs.
For the past two months, I've recovered my system to factory default settings using Rescue and Recovery for over twenty times, each time with the latest Intel Turbo Memory driver and BIOS. Notwithstanding that, BSOD recurrs.
During these painful experiences, I tried two options: 1) making my X61 up-to-date by using System Update and Windows Update (including Vista SP1 or excluding Vista SP1); 2) keeping my X61 the status as factory default (i.e. without updating through either System Update or Windows Update (the automatic/scheduled update function of both is turned off)). In either case, BSOD recurrs.
I'm 100% positive that the BSOD does not arise from any hardware or software/firmware I install. I never install any hardware (e.g. RAM). And, it is not caused by any software/firmware I install: the clear and unequivocal evidence is that at one time,I encountered BSOD while having restored back to factory setting and booting for the first time.
I live in Taiwan, and I seldom heard this BSOD here.  All of my friends (as most of Taiwan residents) using X61 operate in Traditional Chinese environment, whereas I operate in English environment. In Taiwan, when booting for the first time after purchase/recovery, the Windows Vista Business system provides for lanuage choice (Traditional Chinese or English), and, once chosen, the language cannot be altered later on (unless, of course, the system is restored back to factory default settings).
My system specs are the same as the day I purchased it and are listed below (as I'm not sure if my machine type X61 7673-CW9 is applicable outside Taiwan):
Processor: Intel(R) Core(TM)2 Duo CPU T8300 @ 2.4GHz
Memory: 1.00 G.B.
System: Windows Vista Business (32-bit)
Hard Drive: 160 G.B. @ 7,200 r.p.m.
And, of course, with Intel Turbo Memory 1 G.B.
I contacted the Lenovo support staff here in Taiwan for countless times, but they seem to be clueless. I learned that some friends at this forum downgraded their OS back to Windows XP, but I chose not to. The reason is simple: my purchase price for X61 7673-CW9 includes the Intel Turbo Memory, which cannot function under Windows XP (at least so far).
Therefore, I just wish to share my experience here and perhaps I can get some advice from you and other friends here. Any advice will be tremendously and enormously appreciated.
Kevin Chen @ Taiwan

"Sorry, we couldn't find your file. Is it possible it was moved, renamed or deleted?" Error with SharePoint 2013 and Office Web Apps

When I try to open any docx file from the SharePoint it opens on web via office web apps, and when I choose edit document > edit in Word , Microsoft word show me this error "Sorry, we couldn't find your file.
Is it possible it was moved, renamed or deleted?" followed by half a url to the end users document on onedrive.
I noted that this problem only happens with Docx files, with specific users and only when you try to open the Docx file from OneDrive folder ( SkyDrive ) which is hosted in the MySite.
Any Help?

Hi,
According to your post, my understanding is that you failed to open the Docx file from OneDrive folder ( SkyDrive ).
Since this problem only happens with Docx files, with specific users, I recommend to delete and recreate the personal site for the specific users.
More information:
Configure My Sites in SharePoint Server 2013
Best Regards,
Linda Li
Linda Li
TechNet Community Support

Deployment Error with jdk 5 and oc4j_extended_101320.zip

Hello,
I get the following error when I try to deploy my application using jdk 5 and oc4j (oc4j_extended_101320.zip) . I am sure no references of jdk1.4 are being used anywhere. I also tried deleting the persistence directory to make sure there are no lock files anywhere , but in vain. I am stuck with this problem and I urgently need a solution to get past this. Any help in this regard is appreciated. Thanks. Here is the stack trace.
This load was initiated at sim.root:0.0.0 using the Class.forName() method.
The missing class is not available from any code-source or loader in the system.
07/12/31 01:19:17 WARNING: DeployerRunnable.run java.lang.InstantiationException: Application: sim is in failed state as initialization failedoracle.oc4j.admin.internal.DeployerException: java.lang.InstantiationException: Application: sim is in failed state as initialization failed
     at oracle.oc4j.admin.internal.DeployerBase.execute(DeployerBase.java:126)
     at oracle.oc4j.admin.jmx.server.mbeans.deploy.OC4JDeployerRunnable.doRun(OC4JDeployerRunnable.java:52)
     at oracle.oc4j.admin.jmx.server.mbeans.deploy.DeployerRunnable.run(DeployerRunnable.java:81)
     at com.evermind.util.ReleasableResourcePooledExecutor$MyWorker.run(ReleasableResourcePooledExecutor.java:298)
     at java.lang.Thread.run(Thread.java:595)
Caused by: java.lang.InstantiationException: Application: sim is in failed state as initialization failed
     at com.evermind.server.Application.setConfig(Application.java:497)
     at com.evermind.server.Application.setConfig(Application.java:340)
     at com.evermind.server.ApplicationServer.addApplication(ApplicationServer.java:1879)
     at oracle.oc4j.admin.internal.ApplicationDeployer.addApplication(ApplicationDeployer.java:512)
     at oracle.oc4j.admin.internal.ApplicationDeployer.doDeploy(ApplicationDeployer.java:196)
     at oracle.oc4j.admin.internal.DeployerBase.execute(DeployerBase.java:93)
     ... 4 more
Caused by: java.lang.InstantiationException: Error initializing ejb-modules: [sim:oracle_sim_closed_ejb:Transfer] - Unable to load ejb-class oracle.retail.sim.closed.transfer.ejb.TransferEjb, see section 23.2 of the EJB 2.1 specificationoracle.classloader.util.AnnotatedClassNotFoundException:
     Missing class: oracle.retail.sim.closed.transfer.ejb.TransferEjb
     Dependent class: com.evermind.server.ejb.deployment.BeanDescriptor
     Loader: oc4j:10.1.3
     Code-Source: /D:/jdk5andOc4j/OC4J/oc4j_extended_101320/j2ee/home/lib/oc4j-internal.jar
     Configuration: <code-source> in META-INF/boot.xml in D:\jdk5andOc4j\OC4J\oc4j_extended_101320\j2ee\home\oc4j.jar

For internal questions please use the internal mailing lists...
--olaf

Full Export/Import Errors with Queue tables and ApEx

I'm trying to take a full export of an existing database in order to build an identical copy in another database instance, but the import is failing each time and causing problems with queue tables and Apex tables.
I have used both the export utility and Data Pump (both with partial and full exports) and the same problems are occurring.
After import, queue tables in my schema are unstable. They cannot be dropped using the queue admin packages as they throw ORA-24002: QUEUE_TABLE <table> does not exist exceptions. Trying to drop the tables causes the ORA-24005: must use DBMS_AQADM.DROP_QUEUE_TABLE to drop queue tables error
As a result, the schema cannot be dropped at all unless manual data dictionary clean up steps (as per metalink) are done.
The Apex import fails when creating foreign keys to WWV_FLOW_FILE_OBJECTS$PART. It creates the table ok, but for some reason the characters after the $ are missing so the referencing tables try to refer to WWV_FLOW_FILE_OBJECTS$ only.
I am exporting from Enterprise Edition 10.2.0.1 and importing into Standard edition 10.2.0.1, but we are not using any of the features not available in standard, and I doubt this would cause the issues I'm getting.
Can anyone offer any advice on how I can resolve these problems so a full import will work reliably?

Thanks for the lead!
After digging around MetaLink some more, it sounds like I'm running into Bug 5875568 (MetaLink Note:5875568.8) which is in fact related to the multibyte character set. The bug is fixed in the server patch set 10.2.0.4 or release 11.1.0.6.

DHCP Error with WLC 2504 and Aironet 2600 setup across subnets

Similar Messages

Maybe you are looking for