DHCP issues with Cisco WAP 321

I have 4 Cisco WAP 321's in my office connected to our Cisco 2911 ISR for DHCP, everything is fine on the office wifi on vlan 1 but vlan 3 with the guest wifi network it fails to obtain an IP address. I have tried under each of the WAPs to make sure it wasnt just the one nearest my desk. I was on the phone yesterday with Cisco about this and we turned on debugging and watched the DHCP requests and no requests even hit the ISR (only thing I have smartnet support on). I noticed our firmware was a few versions old so updated that this morning but still have the same issues so now I am turning to you all to help me figure this out.
Thanks
Jake
This topic first appeared in the Spiceworks Community

Similar Messages

Cisco WAP 321 Quality Superb Worst + RMA Slow

hi Everyone, recently i notice that the WAP 321 quality is superb worst as base on project we bought 13 units of the cisco WAP 321, out of three not even use for 1 months the unit faulty (unit cannot be power UP) but adapter power is working fine.
beside the quality issues, the RMA process also very slow, when we send the unit to distributor for RMA claim, the cisco feedback the unit need to wait until November of 2015, this ridiculous, how u imagine the unit faulty the replacement unit only can send it back to you almost in 9 months time. I really can't believe it, cisco is so worst on the RMA claim.

this is the case number, we are planning to return all the cisco ap to cisco, as our end user and us really piss off with the RMA process and quality of the cisco AP. we now waiting the feedback from the ECS which is the distributor in malaysia.

Issue with cisco acs 4.2.Users unable to login aaa client but after restarting group policy able to login

issue with cisco acs 4.2.Users unable to login aaa client but after restarting group policy able to login

issue with cisco acs 4.2.Users unable to login aaa client but after restarting group policy able to login

Directory Caching issue with Cisco Jabber client for Windows

Hi ,
I am facing cache issue with Cisco Jabber client for Windows. If I do any change related to modification or deletion of contacts in Active Directory/ Callmanager, it does not reflect in the Jabber. Because jabber takes the contacts from the locally stored cache file in the Windows system.
Every time I have to remove the cache file to overcome this issue, practically it's not possible to do the same with all the Widows users. As, if any employee leaves the company and still I can see his contact appears in the "Cisco Jabber client". I have not seen this issue with Android/Apple iOS.
Is there any automated way to remove the cache file?
Here is the detail of CUCM,Presence and Jabber.
CUCM version: 9.1.x
Presence : 9.1.X
Jabber : 10.5 and 10.6

Hello
On our environment we had to install a dedicated Microsoft Certificate Authority "just for Cisco Jabber usage" to house the
Network Device Enrollment Service.
Our certificate for the CUPS were generated on this Certification Authority too.
I discussed this certificate matter with my colleagues this afternoon and nobody seems to remember how these certificates were deployed into the
Enterprise Trust store for the users.
But I think they asked all 400 users to accept the 3 certificates by answering "yes" to the popup instead of using a script deployed by GPO...
I wish you success with that deployment and really hope you have a technical partner that *Knows* this subject.
Our partner left us alone with that unfortunately.
Florent
EDIT: If the "Certutil script method" works, please let me know. This could be useful in our own deployment.

MacBook and MacBook Pro with 10.6: Wireless Airport Issues with Cisco

Long Story but please bear with me:
Loaded SL on my daughters MacBook and my MacBook Pro. Internet worked flawlessly at our house (WEP encrypted) and on other public wifi. When my daughter went back to her sorority house at college 24 hours later, she could not access the internet using the sorority house network (Cisco Aironet 1800 router and Cisco Airo Access Points).
Her Airport on the MacBook appeared connected at full strength yet no internet. Two calls to Apple support (they were very nice) did not help. All the following were tried:
1. Reset PRAM
2. Deleted Airport and Safari plists
3. Edited locations
4. Removed Battery
5. Others I cannot now remember
Still no net. However, she could 'pirate' and hop on line with other identified public wifi adjacent to the sorority house. I drove to the sorority house today and tried to get on the network wirelessly using my MacBook Pro with SL. Same identical results to hers. Another MacBook without SL works great and gets right on the network.
Is this some SL influenced issue with the Airport card and the Cisco system? Weird that both of our laptops work great with several other wifi networks but not the one at the sorority house.
Could much of what we all our seeing with the internet access problem lie not with issues within our software or computers but with the routers and access points not being compatible? I have very little understanding of this stuff (as you all can probably tell) but the Apple Support people acted like it was a old firmware issue with Cisco and not with SL. Not actually what I wanted to hear.
Any ideas or suggestions?

Your description there, particularly the last part, sounds like my problem. At home, we connect using Airport and ADSL which was OK, once SL had sorted out passwords.
At my office, where there are two wifi systems, I could not get on either, although did have IP numbers on both. The link to the outside world is via a proxy which uses a PAC file. Network Diagnostics reported each time (whatever I did) that the link to the server was OK, but the Internet was not.
I created a new Location with identical settings (typing them in and not copying) and the only visible difference is that the new location has no DNS numbers -- I had not noticed that before. The moment I pressed, Apply, the computer was online.
I was guessing that there was a conflict in a .plist file somewhere; but now I wonder if DNS might have been the reason (the DNS number usually used is the one from the router itself).

Issue with cisco ONS 15310. Slot with Ethernet ports, designed for bridging.

Hi, guys. I’ve got an issue with cisco ONS 15310 sdh optical network. I’ve got a special slot with Ethernet ports, designed for bridging. Assume, we’ve got to multiplexers, named A and B with ports A0 and B0 respectively. The ios console of these slots says, the configuration is as follows:
no ip address set on these ports
Ports are administratively up
Auto mdix
Bridge groups are the same on these ports.
Dot1q tunnel.
I’m trying to monitor a device with an ip-address connected to port B0. It answers ping if I connect the notebook directly to a device. But if I connect the notebook to port A0 and ping the device pluged in port B0 through the optical network, it doesn’t answer. I tried connections with straight and cross cable.
Guys, who set the network said, it should work as a point to point bridge with no extra configuration. But it doesn’t. I used wireshark sniffer to lookup what’s happening on port A0. All I see is cdp-s from port A0 and self-announcements of the notebook.
Any suggestions? Thank you in advance.

B
Building configuration...
Current configuration : 3712 bytes
! Last configuration change at
version 12.2
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
hostname B
boot-start-marker
boot-end-marker
enable password -
clock timezone -
ip subnet-zero
no ip domain-lookup
no mpls traffic-eng auto-bw timers frequency 0
bridge 100 protocol ieee
bridge 140 protocol ieee
bridge 141 protocol ieee
bridge 142 protocol ieee
bridge 143 protocol ieee
bridge 144 protocol ieee
interface Loopback0
ip address 192.x.0.x 255.255.255.255
interface FastEthernet0
description -
no ip address
mode dot1q-tunnel
bridge-group 140
bridge-group 140 spanning-disabled
interface FastEthernet1
description --- B0 ---
no ip address
mode dot1q-tunnel
bridge-group 141
bridge-group 141 spanning-disabled
interface FastEthernet2
description -
no ip address
mode dot1q-tunnel
bridge-group 142
bridge-group 142 spanning-disabled
interface FastEthernet3
description -
no ip address
mode dot1q-tunnel
bridge-group 143
bridge-group 143 spanning-disabled
interface FastEthernet4
description -
no ip address
mode dot1q-tunnel
bridge-group 144
bridge-group 144 spanning-disabled
interface FastEthernet5
no ip address
shutdown
interface FastEthernet6
no ip address
shutdown
interface FastEthernet7
description -
no ip address
shutdown
mode dot1q-tunnel
bridge-group 100
bridge-group 100 spanning-disabled
interface POS0
description -
no ip address
crc 32
interface POS0.1
encapsulation dot1Q 141
no snmp trap link-status
bridge-group 141
interface POS0.2
encapsulation dot1Q 142
no snmp trap link-status
bridge-group 142
interface POS0.3
encapsulation dot1Q 143
no snmp trap link-status
bridge-group 143
interface POS0.4
encapsulation dot1Q 144
no snmp trap link-status
bridge-group 144
interface POS0.5
description -
encapsulation dot1Q 140
no snmp trap link-status
bridge-group 140
interface POS1
no ip address
crc 32
interface POS1.1
encapsulation dot1Q 100
no snmp trap link-status
bridge-group 100
router ospf 100
log-adjacency-changes
network 192.x.0.x 0.0.0.0 area 0
ip default-gateway [x.x.x.x]
ip classless
no ip http server
snmp-server community public RO
snmp-server ifindex persist
snmp-server trap link ietf
snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
snmp-server enable traps tty
snmp-server enable traps config
snmp-server enable traps cpu threshold
snmp-server enable traps entity
snmp-server enable traps syslog
snmp-server enable traps hsrp
snmp-server enable traps config-copy
snmp-server enable traps bridge
snmp-server enable traps ospf state-change
snmp-server enable traps ospf errors
snmp-server enable traps ospf retransmit
snmp-server enable traps ospf lsa
snmp-server enable traps ospf cisco-specific state-change
snmp-server enable traps ospf cisco-specific errors
snmp-server enable traps ospf cisco-specific retransmit
snmp-server enable traps ospf cisco-specific lsa
snmp-server enable traps bgp
snmp-server enable traps pim neighbor-change rp-mapping-change invalid-pim-message
snmp-server enable traps ipmulticast
snmp-server enable traps rtr
snmp-server enable traps mpls traffic-eng
snmp-server enable traps mpls ldp
snmp-server enable traps rsvp
snmp-server enable traps l2tun session
snmp-server enable traps mpls vpn
snmp-server host x.x.x.x public
control-plane
line con 0
line vty 0 4
password -
logging synchronous level 4
login
end

Cisco WAP 321 causes network failure ?

Hi everybody.
I recently bought a Cisco WAP 321 for my company, but when i connect it to the network, the switch on which I connect crashes, and I lose all connectivity to the network, (internet also). i have to unplug the WAP321 and wait for a few minutes to be able to use the network again.
I'm currently using a small 8 port switch, There are usually 3 or 4 users connected on it. When I try connecting the WAP321 on another switch, only connected to 1 computer, it seems to be working : I can access the configuration page, and make some modifications.
Has anyone had this problem already ?
Any idea ?
Thanks everybody for your time !

Hi, My name is Eric Moyers. I am a Network Support Engineer in the Cisco Small Business Support Center. Thank you for using the Cisco Community Post Forums.
Could you give a little more detail about your network? What is the switch that you are connecting to? The 8 port and the other one. A network topology would be helpful as well.
Thanks
Eric Moyers .:|:.:|:.
Cisco Small Business US STAC Advanced Support Engineer
CCNA, CCNA-Wireless
866-606-1866 ext 601027
Mon - Fri 09:00 - 18:00 (UTC - 05:00)
*Please rate the Post so other will know when an answer has been found.

Issue with Cisco Meraki APs

Is there any known issues with Cisco Meraki APs with client devices which publish PMF support in probe requests ? We are seeing connectivity issues with Cisco Meraki MR12,MR16 and MX80 models . Please update if there are any known issue with these APs.

Thanks for your thoughts, Nathan. We do actually have the "Enable Fast Reconnect" option selected on our wireless profile. Good idea, though.
We did also (originally) have 2 RADIUS servers defined within our wireless network. What we discovered was that each Meraki AP will try each one in order, top-to-bottom, and then primarily use the server that responded to it first. So, if for any reason you have a short-lived issue with your local RADIUS server responding to requests, and the AP is able to talk to a remote RADIUS server (in our case, one on the other side of the world) instead, the AP will elect to use the remote RADIUS server instead. In our case, the latency is high enough between these APs and this remote RADIUS server that while a client is roaming between APs, and having to re-authenticate, the entire process breaks down because (1) the client is moving between APs faster than the remote RADIUS server can authenticate the client, and (2) the entire exchange and communication ends up timing out -- thus forcing a manual re-connect. This is not a common occurrence by any means, but I just wanted to share what made us later choose to define only 1 RADIUS server, in the network settings. Surely our circumstance here is rather unique, but I thought it might be worth mentioning. Having only 1 RADIUS server defined forces ALL of our APs to use the same RADIUS server, regardless of anything else. It has resulted in a much smoother re-auth process for our clients.
I appreciate the link you sent, however. If I come across anything else that is helpful, I'll certainly post it back here. I appreciate your input once again!

Cisco WAP 321 found bug that causes loss of config

I have been setting up a WAP 321 which has been unable to retain it's settings across reboots.
What I have found is that if I leave the Timezone set to USA (Pacific) the WAP 321 can be rebooted without losing config, but as soon as I set the timezone to United Kingdom the next reboot will cause the device to take a long time to reboot and will have then gone back to factory default setings.
To help me determine if I have a faulty unit, does any one else have one they'd be willign to set to United Kingdom timezone & reboot to see if you get the same results?

Hi Tom,
It seems the exact same problem, described in diferent ways.
For me even if i configure a different management IP and after that reboot the system, the system take much time too boot and my laptop lan interface keeps goind "connected, disconnected, connected, disconnected..." until i turn off the access point off and turn it on again after about 10 seconds.
When it boots is in factory default settings.
When i'm configuring the access point on Safari Browser on a Mac laptop, i have no problem at all. I can change everything and reboot every time i want without losing my configurations.
The problem is only when i'm configuring on a windows laptop with IE9 or Google Chrome.
I will send you an e-mail with my CCOID, serial number of the access point and this description.
Note that this is the second Cisco WAP321 that we have received with the exact same symptom. We have returned the first one and received the second one with the same problem.
Best regards,
Vitor Oliveira.

10.5 DHCP issues with Wireless - self assigned IPs?

We're having an issue with Mac OSX 10.5.4 clients, running the latest software updates, not getting an IP address via DHCP on our wireless network.
We're using Cisco APs, with multiple VLANs & SSIDs. They authenticate, but get automatic self-assigned IP addresses. None of our PC clients are experiencing this issue, nor older 10.4.x OSX clients. This looks like a bug, from what I was able to discover:
http://forums.macrumors.com/showthread.php?t=384947
Is Apple aware of this, and/or working on a fix? I've seen many issues over the last year or so with Airport clients and wireless connectivity..

This is a "user to user" help forum that is designed as a self-help system, independent of Apple's Technical Support system. No one here can say what Apple knows or is doing about a specific issue (pure speculation is discouraged). We share experience and suggest possible solutions or workarounds.
One way to ensure that your issue is brought to Apple's attention is to use their feedback form for OSX - http://www.apple.com/feedback/macosx.html
Since the link you posted is from late last year, there have been many updates to Leopard. Some of the updates mention network reliability. Even though Apple has stated that the Pram chips don't control network connections, I have had some luck by Zapping The Pram - http://support.apple.com/kb/HT1379 - Remember to check your System Prefs for things like date/time settings after you Zap.

Calling issue with Cisco 7937 conference station

Hi Friends,
I am facing issue wiht Cisco 7937 conference station, our customer have various branch offices accross the world. All branches are connected over MPLS through service provider( SIP service provider) . there is a centralized CUCM and remote office have SIP Voice gateways .
When making calls from once remote site to another using Cisco 6921 phones calls working fine
When making calls from once remote site to another using Cisco 7937 conference station to make call any phone at remote office, calls are getting disconneted, remote phone rings when calls, but its gets fast busy tone when other party picks up the phone and not able to talk.
I suspect the issue with Codec but we have configured transcoders in VG and registered with CUCM
Please help me if any one experience such issue earlier.
Regards
Siva

hi Basant,
1. Actually tow phones A and B are registerd with centralized CUCM, A and B are located in two different locations, RTP traffic between And B pass through service provider.
Call Flow --> Phone A ---->CUCMRouterpattern--> SIP trunk ----> Voice gateway--->Service provider cloud---> Respective Voice Gateway---> CUCM -- Phone B
Show Run
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2014.02.27 15:14:52 =~=~=~=~=~=~=~=~=~=~=~=
sh run
Building configuration...
Current configuration : 12139 bytes
! Last configuration change at 06:35:59 UTC Tue Feb 25 2014
! NVRAM config last updated at 11:16:38 UTC Mon Feb 24 2014 by administrator
! NVRAM config last updated at 11:16:38 UTC Mon Feb 24 2014 by administrator
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname eucamvgw01
boot-start-marker
boot system flash:c2900-universalk9-mz.SPA.151-4.M5.bin
boot-end-marker
card type e1 0 0
logging buffered 51200 warnings
no logging console
no aaa new-model
no network-clock-participate wic 0
no ipv6 cef
ip source-route
ip traffic-export profile cuecapture mode capture
bidirectional
ip cef
ip multicast-routing
ip domain name drreddys.eu
ip name-server 10.197.20.1
ip name-server 10.197.20.2
multilink bundle-name authenticated
stcapp ccm-group 2
stcapp
stcapp feature access-code
stcapp feature speed-dial
stcapp supplementary-services
port 0/1/0
fallback-dn 5428025
port 0/1/1
fallback-dn 5428008
port 0/1/2
fallback-dn 5421462
port 0/1/3
fallback-dn 5421463
isdn switch-type primary-net5
crypto pki token default removal timeout 0
voice-card 0
dsp services dspfarm
voice call send-alert
voice call disc-pi-off
voice call convert-discpi-to-prog
voice rtp send-recv
voice service voip
ip address trusted list
ipv4 10.198.0.0 255.255.255.0
ipv4 152.63.1.0 255.255.255.0
address-hiding
allow-connections sip to sip
no supplementary-service h225-notify cid-update
no supplementary-service sip moved-temporarily
no supplementary-service sip refer
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none
fax-relay ans-disable
sip
rel1xx supported "track"
privacy pstn
no update-callerid
early-offer forced
call-route p-called-party-id
voice class uri 100 sip
host 41.206.187.71
voice class codec 10
codec preference 1 g711alaw
codec preference 2 g711ulaw
codec preference 3 ilbc
codec preference 4 g729r8
codec preference 5 g729br8
voice class codec 20
codec preference 1 g729br8
codec preference 2 g729r8
voice moh-group 1
moh flash:moh/Panjo.alaw.wav
description MOH G711 alaw
multicast moh 239.1.1.2 port 16384 route 10.198.2.9
voice translation-rule 1
rule 1 /^012237280$..$/ /54280\1/
rule 2 /^012236514$..$/ /54214\1/
rule 3 /^01223651081/ /5428010/
rule 4 /^01223506701/ /5428010/
voice translation-rule 2
rule 1 /^00$.+$/ /+\1/
rule 2 /^0$.+$/ /+44\1/
rule 3 /^$[0-9].+$/ /+\1/
voice translation-rule 3
rule 1 /^9$.+$/ /\1/
rule 2 /^\+44$.+$/ /0\1/
rule 3 /^\+$.+$/ /00\1/
voice translation-rule 4
rule 1 /^54280$..$/ /12237280\1/
rule 2 /^54214$..$/ /12236514\1/
rule 3 /^\+44$.+$/ /\1/
rule 4 /^.54280$..$/ /12237280\1/
rule 5 /^.54214$..$/ /12236514\1/
voice translation-rule 9
rule 1 /^$....$/ /542\1/
voice translation-rule 10
voice translation-rule 11
rule 1 /^\+44122372$....$/ /542\1/
rule 2 /^\+44122365$....$/ /542\1/
voice translation-rule 12
voice translation-rule 13
rule 1 /^$[18]...$/ /542\1/
voice translation-rule 14
voice translation-profile MPLS-incoming
translate calling 10
translate called 9
voice translation-profile MPLS-outgoing
translate calling 11
translate called 12
voice translation-profile PSTN-incoming
translate calling 2
translate called 1
voice translation-profile PSTN-outgoing
translate calling 4
translate called 3
voice translation-profile SRST-incoming
translate calling 14
translate called 13
license udi pid CISCO2921/K9 sn FGL145110RE
hw-module ism 0
hw-module pvdm 0/0
username administrator privilege 15 secret 5 $1$syu5$DsxdOgfS7Wltx78o4PV.60
redundancy
controller E1 0/0/0
ip tcp path-mtu-discovery
ip scp server enable
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
description internal LAN
ip address 10.198.2.9 255.255.255.0
duplex auto
speed auto
interface ISM0/0
ip unnumbered GigabitEthernet0/0
service-module ip address 10.198.2.8 255.255.255.0
!Application: CUE Running on ISM
service-module ip default-gateway 10.198.2.9
interface GigabitEthernet0/1
description to TATA NGN
ip address 115.114.225.122 255.255.255.252
duplex auto
speed auto
interface GigabitEthernet0/2
description SIP Trunks external
ip address 79.121.254.83 255.255.255.248
ip access-group SIP-InBound in
ip traffic-export apply cuecapture size 8000000
duplex auto
speed auto
interface ISM0/1
description Internal switch interface connected to Internal Service Module
no ip address
shutdown
interface Vlan1
no ip address
ip forward-protocol nd
no ip http server
no ip http secure-server
ip route 0.0.0.0 0.0.0.0 10.198.2.1
ip route 10.198.2.8 255.255.255.255 ISM0/0
ip route 41.206.187.0 255.255.255.0 115.114.225.121
ip route 77.37.25.46 255.255.255.255 79.121.254.81
ip route 83.245.6.81 255.255.255.255 79.121.254.81
ip route 83.245.6.82 255.255.255.255 79.121.254.81
ip route 95.223.1.107 255.255.255.255 79.121.254.81
ip route 192.54.47.0 255.255.255.0 79.121.254.81
ip access-list extended SIP-InBound
permit ip host 77.37.25.46 any
permit ip host 83.245.6.81 any
permit ip host 83.245.6.82 any
permit ip 192.54.47.0 0.0.0.255 any
permit icmp any any
permit ip host 95.223.1.107 any
deny ip any any log
control-plane
voice-port 0/1/0
compand-type a-law
timeouts initial 60
timeouts interdigit 60
timeouts ringing infinity
caller-id enable
voice-port 0/1/1
compand-type a-law
timeouts initial 60
timeouts interdigit 60
timeouts ringing infinity
caller-id enable
voice-port 0/1/2
compand-type a-law
timeouts initial 60
timeouts interdigit 60
timeouts ringing infinity
caller-id enable
voice-port 0/1/3
compand-type a-law
timeouts initial 60
timeouts interdigit 60
timeouts ringing infinity
caller-id enable
no ccm-manager fax protocol cisco
ccm-manager music-on-hold bind GigabitEthernet0/0
ccm-manager config server 152.63.1.19 152.63.1.100 172.27.210.5
ccm-manager sccp local GigabitEthernet0/0
ccm-manager sccp
mgcp profile default
sccp local GigabitEthernet0/0
sccp ccm 10.198.2.9 identifier 3 priority 3 version 7.0
sccp ccm 152.63.1.19 identifier 4 version 7.0
sccp ccm 152.63.1.100 identifier 5 version 7.0
sccp ccm 172.27.210.5 identifier 6 version 7.0
sccp
sccp ccm group 2
bind interface GigabitEthernet0/0
associate ccm 4 priority 1
associate ccm 5 priority 2
associate ccm 6 priority 3
associate ccm 3 priority 4
associate profile 1002 register CFB_UK_CAM_02
associate profile 1001 register XCODE_UK_CAM_02
associate profile 1000 register MTP_UK_CAM_02
dspfarm profile 1001 transcode
codec ilbc
codec g722-64
codec g729br8
codec g729r8
codec gsmamr-nb
codec pass-through
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
maximum sessions 18
associate application SCCP
dspfarm profile 1002 conference
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
codec g729r8
codec g729br8
maximum sessions 2
associate application SCCP
dspfarm profile 1000 mtp
codec g711alaw
maximum sessions software 200
associate application SCCP
dial-peer cor custom
name SRSTMode
dial-peer cor list SRST
member SRSTMode
dial-peer voice 100 voip
description *** Inbound CUCM ***
translation-profile incoming PSTN-incoming
incoming called-number .
voice-class codec 10
voice-class sip call-route p-called-party-id
dtmf-relay rtp-nte
no vad
dial-peer voice 500 voip
description *** Inbound TATA MPLS ***
translation-profile incoming MPLS-incoming
session protocol sipv2
session target sip-server
incoming called-number ....
incoming uri from 100
voice-class codec 20
dtmf-relay rtp-nte
no vad
dial-peer voice 510 voip
description *** Outbound TATA MPLS ***
translation-profile outgoing MPLS-outgoing
destination-pattern 54[013-9]....
session protocol sipv2
session target ipv4:41.206.187.71
session transport udp
voice-class codec 20
dtmf-relay rtp-nte
no vad
dial-peer voice 520 voip
description *** Outbound TATA MPLS ***
translation-profile outgoing MPLS-outgoing
destination-pattern 5[0-35-9].....
session protocol sipv2
session target ipv4:41.206.187.71
session transport udp
voice-class codec 20
dtmf-relay rtp-nte
no vad
dial-peer voice 200 voip
description *** Inbound M12 *** 01223651081, 01223651440 - 01223651489
translation-profile incoming PSTN-incoming
session protocol sipv2
session target sip-server
session transport udp
incoming called-number 0122365....
dtmf-relay rtp-nte
codec g711ulaw
no vad
dial-peer voice 201 voip
description *** Inbound M12 *** 012237280XX
translation-profile incoming PSTN-incoming
session protocol sipv2
session target sip-server
session transport udp
incoming called-number 012237280..
dtmf-relay rtp-nte
codec g711ulaw
no vad
dial-peer voice 202 voip
description *** Inbound M12 *** 01223506701
translation-profile incoming PSTN-incoming
session protocol sipv2
session target sip-server
session transport udp
incoming called-number 01223506701
dtmf-relay rtp-nte
codec g711ulaw
no vad
dial-peer voice 210 voip
description *** Outbound M12 ***
translation-profile outgoing PSTN-outgoing
destination-pattern +...T
session protocol sipv2
session target ipv4:83.245.6.81
session transport udp
dtmf-relay rtp-nte
codec g711alaw
no vad
dial-peer voice 211 voip
description *** Outbound ISDN for SRST and emergency ***
translation-profile outgoing PSTN-outgoing
destination-pattern 9.T
session protocol sipv2
session target ipv4:83.245.6.81
session transport udp
dtmf-relay rtp-nte
codec g711alaw
no vad
dial-peer voice 212 voip
description *** Outbound ISDN for emergency ***
translation-profile outgoing PSTN-outgoing
destination-pattern 11[02]
session protocol sipv2
session target ipv4:83.245.6.81
session transport udp
dtmf-relay rtp-nte
codec g711alaw
no vad
dial-peer voice 2000 voip
description *** Outbound to CUCM Primary ***
preference 1
destination-pattern 542....
session protocol sipv2
session target ipv4:152.63.1.19
voice-class codec 10
voice-class sip call-route p-called-party-id
dtmf-relay rtp-nte
no vad
dial-peer voice 2001 voip
description *** Outbound to CUCM Secondary ***
preference 2
destination-pattern 542....
session protocol sipv2
session target ipv4:152.63.1.100
voice-class codec 10
voice-class sip call-route p-called-party-id
dtmf-relay rtp-nte
no vad
dial-peer voice 2002 voip
description *** Outbound to CUCM Teritiary ***
preference 3
destination-pattern 542....
session protocol sipv2
session target ipv4:172.27.210.5
voice-class codec 10
voice-class sip call-route p-called-party-id
dtmf-relay rtp-nte
no vad
dial-peer voice 999010 pots
service stcapp
port 0/1/0
dial-peer voice 999011 pots
service stcapp
port 0/1/1
dial-peer voice 999012 pots
service stcapp
port 0/1/2
dial-peer voice 999013 pots
service stcapp
port 0/1/3
sip-ua
no remote-party-id
gatekeeper
shutdown
call-manager-fallback
secondary-dialtone 9
max-conferences 4 gain -6
transfer-system full-consult
ip source-address 10.198.2.9 port 2000
max-ephones 110
max-dn 400 dual-line no-reg
translation-profile incoming SRST-incoming
moh flash:/moh/Panjo.ulaw.wav
multicast moh 239.1.1.1 port 16384 route 10.198.2.9
time-zone 22
time-format 24
date-format dd-mm-yy
line con 0
login local
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line 131
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 4
session-timeout 60
exec-timeout 60 0
privilege level 15
login local
transport input all
line vty 5 15
session-timeout 60
exec-timeout 60 0
privilege level 15
login local
transport input all
scheduler allocate 20000 1000
ntp server 10.1.30.1
end
eucamvgw01#
Sh SCCP
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2014.03.03 17:57:44 =~=~=~=~=~=~=~=~=~=~=~=
SCCP Admin State: UP
Gateway Local Interface: GigabitEthernet0/0
IPv4 Address: 10.198.2.9
Port Number: 2000
IP Precedence: 5
User Masked Codec list: None
Call Manager: 10.198.2.9, Port Number: 2000
Priority: 3, Version: 7.0, Identifier: 3
Call Manager: 152.63.1.19, Port Number: 2000
Priority: N/A, Version: 7.0, Identifier: 4
Trustpoint: N/A
Call Manager: 152.63.1.100, Port Number: 2000
Priority: N/A, Version: 7.0, Identifier: 5
Trustpoint: N/A
Call Manager: 172.27.210.5, Port Number: 2000
Priority: N/A, Version: 7.0, Identifier: 6
Trustpoint: N/A
MTP Oper State: ACTIVE - Cause Code: NONE
Active Call Manager: 152.63.1.19, Port Number: 2000
TCP Link Status: CONNECTED, Profile Identifier: 1000
Reported Max Streams: 400, Reported Max OOS Streams: 0
Supported Codec: g711alaw, Maximum Packetization Period: 30
Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30
Supported Codec: rfc2833 pass-thru, Maximum Packetization Period: 30
Supported Codec: inband-dtmf to rfc2833 conversion, Maximum Packetization Period: 30
TLS : ENABLED
Transcoding Oper State: ACTIVE - Cause Code: NONE
Active Call Manager: 152.63.1.19, Port Number: 2000
TCP Link Status: CONNECTED, Profile Identifier: 1001
Reported Max Streams: 36, Reported Max OOS Streams: 0
Supported Codec: ilbc, Maximum Packetization Period: 120
Supported Codec: g722r64, Maximum Packetization Period: 30
Supported Codec: g729br8, Maximum Packetization Period: 60
Supported Codec: g729r8, Maximum Packetization Period: 60
Supported Codec: gsmamr-nb, Maximum Packetization Period: 60
Supported Codec: pass-thru, Maximum Packetization Period: N/A
Supported Codec: g711ulaw, Maximum Packetization Period: 30
Supported Codec: g711alaw, Maximum Packetization Period: 30
Supported Codec: g729ar8, Maximum Packetization Period: 60
Supported Codec: g729abr8, Maximum Packetization Period: 60
Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30
Supported Codec: rfc2833 pass-thru, Maximum Packetization Period: 30
Supported Codec: inband-dtmf to rfc2833 conversion, Maximum Packetization Period: 30
Conferencing Oper State: ACTIVE - Cause Code: NONE
Active Call Manager: 152.63.1.19, Port Number: 2000
TCP Link Status: CONNECTED, Profile Identifier: 1002
Reported Max Streams: 16, Reported Max OOS Streams: 0
Supported Codec: g711ulaw, Maximum Packetization Period: 30
Supported Codec: g711alaw, Maximum Packetization Period: 30
Supported Codec: g729ar8, Maximum Packetization Period: 60
Supported Codec: g729abr8, Maximum Packetization Period: 60
Supported Codec: g729r8, Maximum Packetization Period: 60
Supported Codec: g729br8, Maximum Packetization Period: 60
Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30
Supported Codec: rfc2833 pass-thru, Maximum Packetization Period: 30
Supported Codec: inband-dtmf to rfc2833 conversion, Maximum Packetization Period: 30
TLS : ENABLED
Alg_Phone Oper State: ACTIVE - Cause Code: NONE
Active Call Manager: 152.63.1.19, Port Number: 2000
TCP Link Status: CONNECTED, Device Name: AN71FEF7F070080
Reported Max Streams: 1, Reported Max OOS Streams: 0
Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30
Supported Codec: g711ulaw, Maximum Packetization Period: 20
Supported Codec: g711alaw, Maximum Packetization Period: 20
Supported Codec: g729r8, Maximum Packetization Period: 220Supported Codec: g729ar8, Maximum Packetization Period: 220
Supported Codec: g729br8, Maximum Packetization Period: 220
Supported Codec: g729r8, Maximum Packetization Period: 220
Supported Codec: ilbc, Maximum Packetization Period: 120
Alg_Phone Oper State: ACTIVE - Cause Code: NONE
Active Call Manager: 152.63.1.19, Port Number: 2000
TCP Link Status: CONNECTED, Device Name: AN71FEF7F070081
Reported Max Streams: 1, Reported Max OOS Streams: 0
Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30
Supported Codec: g711ulaw, Maximum Packetization Period: 20
Supported Codec: g711alaw, Maximum Packetization Period: 20
Supported Codec: g729r8, Maximum Packetization Period: 220
Supported Codec: g729ar8, Maximum Packetization Period: 220
Supported Codec: g729br8, Maximum Packetization Period: 220
Supported Codec: g729r8, Maximum Packetization Period: 220
Supported Codec: ilbc, Maximum Packetization Period: 120
Alg_Phone Oper State: ACTIVE - Cause Code: NONE
Active Call Manager: 152.63.1.19, Port Number: 2000
TCP Link Status: CONNECTED, Device Name: AN71FEF7F070082
Reported Max Streams: 1, Reported Max OOS Streams: 0
Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30
Supported Codec: g711ulaw, Maximum Packetization Period: 20Supported Codec: g711alaw, Maximum Packetization Period: 20
Supported Codec: g729r8, Maximum Packetization Period: 220
Supported Codec: g729ar8, Maximum Packetization Period: 220
Supported Codec: g729br8, Maximum Packetization Period: 220
Supported Codec: g729r8, Maximum Packetization Period: 220
Supported Codec: ilbc, Maximum Packetization Period: 120
Alg_Phone Oper State: ACTIVE - Cause Code: NONE
Active Call Manager: 152.63.1.19, Port Number: 2000
TCP Link Status: CONNECTED, Device Name: AN71FEF7F070083
Reported Max Streams: 1, Reported Max OOS Streams: 0
Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30
Supported Codec: g711ulaw, Maximum Packetization Period: 20
Supported Codec: g711alaw, Maximum Packetization Period: 20
Supported Codec: g729r8, Maximum Packetization Period: 220
Supported Codec: g729ar8, Maximum Packetization Period: 220
Supported Codec: g729br8, Maximum Packetization Period: 220
Supported Codec: g729r8, Maximum Packetization Period: 220
Supported Codec: ilbc, Maximum Packetization Period: 120
eucamvgw01#

Issues with cisco 1242 aironets

We are currently experiencing and issue with the 1242 AG Wireless Access Points. We have have them configured as 1 Root Access point and 3 Repeaters. The repeaters seem to be experiencing frequency interference issues. The Root AP is using antenna model 2506 and the repeaters 1728's.
What happens is when the repeaters are first started up, they see / communicate to the root access point fine, but within 5 minutes they stop communicating. If we manually set the channel to something different, they see each other for 5 - 10 minutes then eventually disappear and cannot be ping'd or seen with a sh cdp nei.
We have tried various combinations of settings so far. Have tried channel 1 - 13 and the least conjested frequency mode. It usually settles on channel 8 when we put it in that mode. But it is the same sceneario each time. All 3 repeaters show up almost instantly after a channel change, but slowly disappear in less than 10 minutes.
Here is our config:
Version
Cisco IOS Software, C1240 Software (C1240-K9W7-M), Version 12.4(21a)JA1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Wed 16-Sep-09 19:06 by prod_rel_team
ROM: Bootstrap program is C1240 boot loader
BOOTLDR: C1240 Boot Loader (C1240-BOOT-M) Version 12.3(7)JA1, RELEASE SOFTWARE (fc1)
ROOTAP uptime is 2 days, 3 hours, 14 minutes
System returned to ROM by power-on
System image file is "flash:/c1240-k9w7-mx.124-21a.JA1/c1240-k9w7-mx.124-21a.JA1"
cisco AIR-AP1242AG-E-K9    (PowerPCElvis) processor (revision A0) with 24566K/8192K bytes of memory.
Processor board ID FCZ112782K9
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on
1 FastEthernet interface
2 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:1C:58:B1:72:2E
Part Number                          : 73-10256-06
PCA Assembly Number                  : 800-26918-05
PCA Revision Number                  : A0
PCB Serial Number                    : FOC11262N5Z
Top Assembly Part Number             : 800-29233-01
Top Assembly Serial Number           : FCZ112782K9
Top Revision Number                  : A0
Product/Model Number                 : AIR-AP1242AG-E-K9
Configuration register is 0xF
Root AP Config
Current configuration : 1987 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname ROOTAP
no aaa new-model
dot11 syslog
dot11 activity-timeout client maximum 120
dot11 activity-timeout repeater maximum 300
dot11 ssid WIRELESS
   authentication open
   authentication key-management wpa
   guest-mode
   infrastructure-ssid
username user privilege 15 secret 5 password
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers tkip
ssid WIRELESS
antenna gain 5
parent timeout 10000
channel 2417
station-role root access-point
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
shutdown
no dfs band block
channel dfs
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface BVI1
ip address 192.168.2.10 255.255.255.0
no ip route-cache
ip default-gateway 192.168.2.1
ip http server
ip http authentication local
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
line con 0
privilege level 15
logging synchronous
login local
stopbits 1
line vty 0 4
privilege level 15
logging synchronous
login local
stopbits 1
line vty 5 15
privilege level 15
logging synchronous
login local
stopbits 1
end
Repeater Config
Current configuration : 1764 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname REPEATER03
no aaa new-model
dot11 syslog
dot11 ssid WIRELESS
   authentication open
   authentication key-management wpa
   guest-mode
   infrastructure-ssid
username user privilege 15 secret 5 password
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers tkip
ssid WIRELESS
antenna gain 5
parent timeout 10000
station-role repeater
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
shutdown
no dfs band block
channel dfs
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface BVI1
ip address 192.168.2.13 255.255.255.0
no ip route-cache
ip default-gateway 192.168.2.1
ip http server
ip http authentication local
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
line con 0
privilege level 15
logging synchronous
login local
stopbits 1
line vty 0 4
privilege level 15
logging synchronous
login local
stopbits 1
end
We are wondering if you have any tips to get around this.
Also, should these access points be able to handle ~200 clients? How close to the root access point should the repeaters be placed? I basically just go until my signal gets low and put a repeater within that range. Could vary from 30-60 meters away.
Thanks

Also, should these access points be able to handle ~200 clients?
APs, in theory, can handle >1,200 clients. In theory. In practice, Cisco recommends between 12-25 clients. Imagine if you have, say, 50 clients and they are trying to access the network on a 100 Mbps FastEthernet connection. That slows them down, right? But consider wireless as a broadcast. One talks and the rest listens.

Driver issue with Cisco HD Precision / JFV 4.4

Hi,
Just to installed Jabber for Video4.4 on my laptop ( win7 64bits)
all works fine except the video!! i use a Cisco HD precision wih Jabber, may be a driver issue, the camera is not recognized.
When i selected my integreted camera from laptop, the video is going up.
i've already the same issue with Jabber Video 4.3.
Does anyone has got the same issue? Any idea?
Thanks

Thread back from the dead...
I have this exact scenario playing out today trying to use a PrecisionHD USB camera with Windows 7. Completed the 1.5 update listed here and following the update I see the results in the picture. The LibUSB device is present, and it looks like a Tandberg HD camera is known to the system, but not accessible/usable.
Anybody have success with this issue or have any additional ideas to try?

Windows 8 64 bit issues with Cisco AnyConnect Secure Mobility Client version 3.1.04072

I am having an issue with the Cisco AnyConnect Secure Mobility Client version 3.1.04072 on a Windows 8 64 bit laptop.
I am able to create the VPN connection but the connection will not allow data to be transferred.
Stats from a manual connection:
Cisco AnyConnect Secure Mobility Client Version 3.1.04072
VPN Stats
    Bytes Received: 14375
    Bytes Sent: 0
    Compressed Bytes Received: 0
    Compressed Bytes Sent: 0
    Compressed Packets Received: 0
    Compressed Packets Sent: 0
    Control Bytes Received: 0
    Control Bytes Sent: 0
    Control Packets Received: 0
    Control Packets Sent: 0
    Encrypted Bytes Received: 7820
    Encrypted Bytes Sent: 1207
    Encrypted Packets Received: 9
    Encrypted Packets Sent: 3
    Inbound Bypassed Packets: 0
    Inbound Discarded Packets: 0
    Outbound Bypassed Packets: 0
    Outbound Discarded Packets: 0
    Packets Received: 4
    Packets Sent: 0
    Time Connected: 00:03:01
Protocol Info
    Inactive Protocol
        Protocol Cipher: RSA_3DES_168_SHA1
        Protocol Compression: None
        Protocol State: Disconnected
        Protocol: DTLS
    Active Protocol
        Protocol Cipher: RSA_3DES_168_SHA1
        Protocol Compression: Deflate
        Protocol State: Connected
        Protocol: TLS
OS Version
    Windows 8 : WinNT 6.2.9200
Log from the data transmission software:
24/12/2013 12:51:13 - Application version = 1.11.28.0
24/12/2013 12:51:13 - Lodgement Library Version = 1.11.28.0
24/12/2013 12:51:13 - Connection Method = INTERNET
24/12/2013 12:51:13 - DIS Connection Type = Automatic
24/12/2013 12:51:13 - VPN Client = ACTIVE
24/12/2013 12:51:13 - Check Available Connections = NOT ACTIVE
24/12/2013 12:51:13 - Windows 8 (6.2.9200 SP )
24/12/2013 12:51:13 - Language: English (Australia)
24/12/2013 12:51:13 -
24/12/2013 12:51:13 - Connected to ISP via LAN
24/12/2013 12:51:13 - Checking for presence of VPN client.
24/12/2013 12:51:13 - VPN client found. (C:\Program Files (x86)\Cisco\Cisco AnyConnect Secure Mobility Client\vpncli.exe)
24/12/2013 12:51:13 - The Cisco AnyConnect Secure Mobility Client application is in use.
24/12/2013 12:51:18 - Terminating Cisco AnyConnect Secure Mobility Client in progress ...
24/12/2013 12:51:18 -
24/12/2013 12:51:18 - Checking Cisco AnyConnect version.
24/12/2013 12:51:19 - Cisco AnyConnect Secure Mobility Client (version 3.1.04072) .
24/12/2013 12:51:19 - Copyright (c) 2004 - 2013 Cisco Systems, Inc. All Rights Reserved.
24/12/2013 12:51:19 - Config file directory:C:\Program Files (x86)\Cisco\Cisco AnyConnect Secure Mobility Client\
24/12/2013 12:51:19 -
24/12/2013 12:51:19 - Loading profile:C:\ProgramData\Cisco\Cisco AnyConnect Secure Mobility Client\Profile\ELS-IMelAde-TCP.xml
24/12/2013 12:51:19 -
24/12/2013 12:51:19 - Initializing the VPN connection.
24/12/2013 12:51:19 - Ready to connect.
24/12/2013 12:51:19 - Ready to connect.
24/12/2013 12:51:19 - Contacting ELS-IMelAde-TCP.
24/12/2013 12:51:23 - Authenticating user.
24/12/2013 12:51:23 - Connected to VPN concentrator.
24/12/2013 12:51:23 - Establishing VPN session...
24/12/2013 12:51:23 - Checking for profile updates...
24/12/2013 12:51:23 - Checking for product updates...
24/12/2013 12:51:23 - Checking for customization updates...
24/12/2013 12:51:23 - Performing any required updates...
24/12/2013 12:51:23 - Establishing VPN session...
24/12/2013 12:51:23 - Establishing VPN - Initiating connection...
24/12/2013 12:51:24 - Establishing VPN - Examining system...
24/12/2013 12:51:24 - Establishing VPN - Activating VPN adapter...
24/12/2013 12:51:24 - Establishing VPN - Configuring system...
24/12/2013 12:51:24 - Establishing VPN...
24/12/2013 12:51:24 - Connected to VPN concentrator.
24/12/2013 12:51:24 - Connected to ELS-IMelAde-TCP.
24/12/2013 12:51:24 - Connected to VPN concentrator.
24/12/2013 12:51:24 - Connection to VPN client return code = 0.
24/12/2013 12:51:24 - Connected to VPN concentrator.
24/12/2013 12:51:24 - Connecting : Connecting to 203.202.43.2.
24/12/2013 12:51:45 - Error in ConnectToDIS - Socket Error # 10060
Connection timed out.
24/12/2013 12:51:46 -
24/12/2013 12:51:46 - Disconnecting from the VPN concentrator.
24/12/2013 12:51:46 - Disconnect in progress, please wait...
24/12/2013 12:51:46 - Detaching AnyConnect, please wait...
24/12/2013 12:51:47 - Detached.
24/12/2013 12:51:47 - Disconnected from VPN concentrator.
24/12/2013 12:51:47 - *****************************************************
24/12/2013 12:51:47 -               END OF LODGEMENT PROCESS
24/12/2013 12:51:47 - *****************************************************
Issue history:
- Previously running Cisco VPN client on Windows 8 64 bit laptop (VPN working and able to transmit data over VPN)
- Upgrade to Windows 8.1 stopped the VPN client working
- Refreshed system back to Windows 8 and reinstalled all software
- Cisco VPN client would not install on system
- Cisco AnyConnect Secure Mobility Client installs and is able to connect to VPN host
- Cisco AnyConnect Secure Mobility Client downloads and installs software from VPN host
- Data transmission software returns error code #10060
Any assistance would be greatly appreciated.

anyone found the fix for this?

Coa issue with Cisco ISE 1.2

Hi, i am currently implementing webauth with Cisco ISE for self register, but i am having issue coa. I was able to get non-windows machine to work but with windows i can't push out the url redirection through coa. I have enabled debug and i can see ISE trying to push out the url redirection to the port, however the url was not show when i issue a show authentication session interface gi 1/0/x command. The only issue i can see from the debugging is that the interface failed authorization first then a success authorization right after. Again, the url redirection work on non-windows machine, i have even go as far as disable dot1x supplicant on windows and it still didnt fix the issue.
please see attachment for the debugging i had mention above. If anyone know or had this issue before please let me know how i can resolve this.

finally figured it out. redirection acl was mess up.

DHCP issues with Cisco WAP 321

Similar Messages

Maybe you are looking for