DIAG LIGHT FLASHING

I have tried unsuccessfully to recover my RV042 to a usable state.  The diag light blinks and Ive tried several ways to upgrade the firmware by holding the reset for 30 or more seconds.  I also cannot find anywhere this TFTP tool for the RV042 that people are talking about.  And so I'm stuck with a blinking led driving me crazy. Do I just dump this router and buy a new one or a better one?  Up to this point I was very happy with the features and capabilities.

red diag light means bad news..
contrary to what chickmagnet said, resetting the router for 1 min would be good but not forever. it may work but just for the time being. then try to get the firmware updated while your at it. if it already is, re-flash it. but do bear in mind that this will only be a temporary fix IF it works..
the best thing to do is to replace it with a new one so you would not have to go through that much hassle.

Similar Messages

  • BEFW11S4 v2 diag light

    I've just upgraded my BEFW11S4 V2 to the latest (and supposedly correct) version of the firmware (v1.45.10). Upgrade said it completed successfully but now my Diag light is flashing and I can't get to the configuration web page.
    I have tried re-flashing as per FAQ Answer 517 (using tftp and slower connection). Same result - says it finished okay, but problem is still there.
    Ideas of how to correct this? Or is it bricked? I'd love to try re-flashing an older version (or the original) firmware. Any idea where I can find a copy?

    You can find the older firmware's here.

  • Re: Tecra M9- Dropped, Hold tab and it beeps, fan spins lights flash.

    Hi,
    My Tecra M9 was dropped, worked for a few days and now doesn't. I suspect a bad CPU.
    When I plug it in, the notebook tries to turn on without me having to press anything.
    There is no backlight, no screen activity, no beeps, no fan.
    If I hold the tab button, or the tilde button while turning it on, the notebook starts to beep, the fan goes on max and the on light flashes.
    What is this, some sort of diag mode?
    Can someone tell me what the beeps and lights mean?
    I can tell you that if I take out the ram, the "pressing tab thing" does nothing.
    Also without a CPU, the "pressing tab thing" does nothing.
    The ram is tested good in another notebook.
    Can anyone confirm that it's a bad CPU?
    Message was edited by: moral hazard
    Message was edited by: moral hazard

    Thanks for answering so soon:)
    I also have a Tecra A9.
    I have tested the ram in the A9 before putting it in my M9.
    I tried every possible combination of ram.
    Here is an interesting thing that happened:
    I took the CPU from my good A9 and put it in the bad M9.
    The M9 shows signs of life.
    It does not try to turn on by itself like before (good).
    When I do try to turn it on, the fan spins at a normal speed (good).
    But the screen stays black (bad).
    Then I put the CPU back into by good A9.
    When I do try to turn the good A9 on, the fan spins at a normal speed (good).
    But the screen stays black (bad).
    I thought I just killed my A9.
    But then I took out the power cord and battery, held the power button for 1 min.
    Try to boot again, works.
    Now I think maybe I should try the CPU in the bad M9 again, this time holding the power button without any battery or power cord like with the good A9.
    Hopefully it will boot normaly like the A9 did.
    I just don't want to kill the A9 while trying to fix the M9.
    Can someone confirm it could be the CPU?

  • My airport time capsule did not set up successfully, and then status light flash amber

    Hi, Guys
      I am the first time user of the time capsule, please help how to proceed?
      I have set up the first time and my airport time capsule does not set successfully, then I try to reset to factory setting. After this, although I use the ethenet cable to connect the router to the airport, the status light flash amber, always, even after the reset.
      Also, I can see that airport time capsule base station from the wireless network when airport is plugged in. However, when I want to access to it.

    Thanks for your guidance, but the product is really anoying. First, I am sure that the airpor utilities is 6.3.
    and I also follow your instruction that to set the IPv6 as local link mode. But still get the same error as mentioned in my first post.
    Therefore, I have tried to use the bridge mode but could not find it, and therefore still can not set it up successfully, even though I reset the factory again(press the reset button 5 secconds at least).

  • HT202157 My apple TV is not working with light flashing after up date

    My apple TV is not working with the light flashing after an up date, what can be done?

    same here macbok air 2012 appletv 3 bugs the **** out of me
    it just stops randomly after a "while"

  • I am having difficult problems with the FocusritePro14 it works for a few then the firewire light flashes it cuts in an out then my MacBookPro crashes and restarts what can be the problem?

    I am trying to figure out why this interface never works like it should, I have the lastest drivers 10.8 OS, The firewire cuts in an out and then crahses my computer, it was working fine for a good month, and then it does this. The people at Focusrite are clueless to what is going on. This is horrible engenerring  on there part. There are three lights on the interface they all light up, then half way through a recording or just lisiting to music, the FW light flashes and cuts out, and now the mac is rebooting when it does that. I highly doubt it is a simple fix, or a bad wire. I have the original cable for the interface that came with it, hooked up to a sonet adapter to fit in the macbook pro because the geniuses at apple decided that they would make that port small.
    Sorry about mispeling its 3 am here in Ohio.  Please can someone help
    Thank you

    Hello Bagpus113
    Check out the article below to troubleshooting issues with the sound for music and for videos. One other thing you can try is to convert the songs to a different format
    iTunes and QuickTime for Windows: Audio does not play or plays incorrectly
    http://support.apple.com/kb/TS1362
    Troubleshooting iTunes for Windows Vista or Windows 7 video playback performance issues
    http://support.apple.com/kb/ts1718
    iTunes: How to convert a song to a different file format
    http://support.apple.com/kb/ht1550
    Regards,
    -Norm G.

  • TS1410 My older iPod is not recognized by iTunes. A yellow light flashes.

    My older iPod is not recognized by iTunes. When plugged in a yellow light flashes. When unplugged and turned on, I see green and yellow lights flashing alternately. Help?

    The Jaguar there is nothing you can do, and the new interface from the dealer are not compatible
    For the BMW, you have to find out what brand interface was installed in the vehicle
    can be dension or original BMW  in the x5, if dension you can get something call
    Scosche passPORT if  BMW brand you can get a new cable from Bmw with the usb and dual power supply,
    In the Mini if DIce brand you will need a new cable or new iPod interface, now they have a usb plug to do updates in case iPhone 5 is release in the future or any other updates from iTunes
    http://www.oemautosound.com/pc-457-164-dice-i-bmw-t5v-mini-cooper-2002-2008-to-i pod-text-ready.aspx

  • C6380 Unresponsi​ve. Multiple lights flashing. Screen is white.

    After several years of dependable use, my C6380 may be dead.  The following lights flash about every second: (small light by + sign, Print Photos, Red Eye Removal, On-Off and blue Wireless light.  Screen is white.  If I hold down Print Photos and On-Off buttons, screen changes to green with numbers 1 thru 5 in white.  Lights quit blinking (On-Off light and small light below memory stick opening are on).  On-Off does not work, must unplug.  Ink carriage does not move when cover is opened, so I cannot remove ink cartridges.  Is there help for this machine?

    You can reset your printer by following the steps mentioned in this post:
    http://h30434.www3.hp.com/t5/Printer-All-in-One-In​stall-and/HP-Photosmart-C6380-All-in-One-always-pr​...
    But, this reset may reset all your wireless customizations as well.
    Hope this helps.
    I work for HP.

  • Apple TV loses picture output and status light flashes rapidly after 5 minutes hooked up via HDMI - DVI cable

    Apple TV connected to a 2005 50" plasma monitor with DVI input via belekin HDMI to DVI cable.  Unit worked perfectly long enough to get it connected to the wireless network and begin the itunes registration process when there was a loss of signal message on the screen from the monitor and the Apple TV status light flashed rapidly and continuously. Reset and reboot yeilded flashing rapid status light and no output detected from the monitor.  I contacted support online and was told to return the unit to the apple store.  I returned home with another brand new apple tv and connected it in the same manner with exactly the same results.  Is there something with the HDMI - DVI interface that is causing this?  Are there known issues with the HDMI - DVI connection to Apple TV with older plasma monitors?

    The Apple TV doesn't actually support DVI. Some have managed to get it to work others have had varying issues with it.

  • HT204400 I turn my Apple TV on and it stays on the setting time anWoke d date scroeen. I've tried the menu button nothing happens except the light flashes about 3 times. I'm trying to connect it to my new wifi but can't cause it won't go on the menu. Gutt

    My Apple TV won't go on the menu page it stays on the time and date screen.every time I press the menu button the light flashes 3 times. Been trying to connect my new wifi but can't cause it won't get of that screen. I've treys turning it off and one still no joy. Gutted. Heip

    My Apple TV won't go on the menu page it stays on the time and date screen.every time I press the menu button the light flashes 3 times. Been trying to connect my new wifi but can't cause it won't get of that screen. I've treys turning it off and one still no joy. Gutted. Heip

  • Sleep light flashes 5 times - no beeps. What does it mean?

    I have a white 2008 Macbook 2.4 Ghz. I recently installed 10.6 from scratch via Retail DVD and the Macbook worked fine. I updated via Software Update and installed all the updates that appeared. There was also a Firmware update to install, which I did after the update to 10.6.8.
    But since then, the Macbook has serious video problems.
    It boots okay, but the sequence is now:
    - front sleep light flashes 5 times; there are no error beeps
    - I hear the startup chime
    - the Apple logo and spinning wheel appear, and bootup continues
    - at the point where the screen goes blue, and would normally boot to the desktop, the screen now goes black and the Macbook appears to go to sleep
    If I wait for a couple of minutes, when I press a key to wake the Macbook from sleep: the DVD spins up, the sleep light flashes 5 times, and I now see the desktop. But then the screen goes black after about 10 seconds.
    Before the screen goes black, I can see that the boot seems to have completed okay. I have a Wifi connection and the date and time are correct.
    If I go really fast, I can move the arrow to the Apple icon in the top bar and choose Shut down or Restart.
    I can boot from the internal HD, an external FW HD and an Install DVD.
    I can hold down the Option key and I get all the bootable volumes to boot from. I can choose any of them, then start the boot process, but at the same point - the blue screen - the screen goes black and the Macbook goes to sleep.
    The Macbook works perfectly fine when connected to an external monitor. In the Display preferences, only the external monitor is available. The Macbook monitor is not listed. As well, iSight and Photo Booth report that no camera is connected.
    I've found some info on the Apple site re. the 5 sleep light flashes, but it only refers to the Macbook Air, and indicates a problem with the battery.
    Has anyone seen this problem with the Macbook?

    From EZ Jim's link, there was another link to this info at the Apple site, re. Power on Self-Tests:
    The power on self-test resides in the ROM of the computer. This test runs whenever the computer is turned on after being fully shut down (the power-on self-test does not run if the computer is only restarted).
    If a fault is detected during the test, you will not hear a normal startup chime. Instead, the system will beep as explained below. If you experience one of these beeps, you may call your Apple Authorized Service Provider for additional troubleshooting assistance.
    1 beep = no RAM installed
    2 beeps = incompatible RAM types
    3 beeps = no good banks
    4 beeps = no good boot images in the boot ROM (and/or bad sys config block)
    5 beeps = processor is not usable
    In addition to the beeps, on some computers the power LED will flash a corresponding number of times plus one. The LED will repeat the sequence after approximately a 5-second pause. The tones are only played once.
    As I wrote, I don't get the Error Beeps. I've had these on other Macs, so I know what they are. Here, I only get the LED flashes.
    What is interesting above is that they say that the Power LED will flash a corresponding number of times (as the beeps) PLUS ONE. In my case, then, if I got 5 flashes, then might it mean NO GOOD BOOT IMAGES IN THE BOOT ROM?
    Anyway, it doesn't seem to have the flashing LED problem any more. No idea where to go from here.

  • My macbook air wont boot up. Just beeps every 5 seconds and a white light flashes on front of keyboard

    My macbook air wont boot up. Just beeps every 5 seconds and a white light flashes on front of keyboard

    That normally indicates an issue with system memory. The startup sequence can't complete the boot due to a memory issue. Take it in for service.

  • Have a nx9600 and when it tries to reboot, the hard drive light comes on, the 2 lock lights flash

    At boot, the hard drive light comes on, the 2 lock lights flash simultanously (A and 1 ) , 2 of the 3 fans come on, then it appears to turn off. It will sit in a loop through the reboot process until the power and the battery have been removed.
    Have replaced the drive and the center fan. The replaced fan is new and an HP fan. When I have been able to get it to boot , loaded windows and linux on the new drive.
    If it sits long enough and you pray  it may reboot. Once I turned it upside down and it rebooted.
    Have had the system up and running for hours with no problem, then have to reboot or a shutdown and won't reboot.
    Suggestions ?

    Install or Reinstall Mavericks or Mountain Lion from Scratch
    Be sure you backup your files to an external drive or second internal drive because the following procedure will remove everything from the hard drive.
    OS X Mavericks- Erase and reinstall OS X
    OS X Mountain Lion- Erase and reinstall OS X
    Note: You will need an active Internet connection. I suggest using Ethernet if possible
                because it is three times faster than wireless.

  • Red Light flashing help

    Hi, I have recently got a curve and after loading the pc software & connected my blackberry to it, it updated etc then my phone went blank and has 2 blinking red lights flashing...anyone know how I can reset phone thanks

    Hi..
    Try the below link for the OS downloads..
    https://developer.blackberry.com/blackberry10devalpha/devalpha_update.html
    thanks..
    Please update the result after applied..
    Thanks

  • HP6310 won't respond to power button, camera light flashes

    After turning my HP6310 off by unlugging the power cord, I can't get it to turn back on properly. I plugged the power cord back in and the display lights up blank and the camera light in the front lower left flashes. The power button does not light up and when pressed, does nothing.

    Hi @mcdillon99,
    Welcome to the HP Forums!
    I noticed that your HP officejet 6310 will not respond to the power button, and the camera light flashes. I am sorry to hear this, but happy to help!
    I would recommend to go through this guide, The HP Printer Won't Turn On or Respond When the Power Button is Pressed. (Even though the guide title may not match your issue, I believe the solutions will help).
    Hope this resolves your issue!  
    RnRMusicMan
    I work on behalf of HP
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" to say “Thanks” for helping!

Maybe you are looking for