Dial-up Modem not detected

Problem:
My system isn't recognizing/finding my internal modem.
What I have:
wvdial and gnome-ppp set up. From the Wiki, I gave all users permission to use wvdial.
What I know:
I ran PuppyOS and was able to get the modem to work - so it's there and functions. (PuppyOS uses wvdial) The modem is at /dev/ttys_PCTELO and I have an init string (though it's a bit different than the one gnome-ppp shows.)
Question:
How do I get Arch to find the modem?

Maybe you could take a look at:
http://wiki.archlinux.org/index.php/Dia … aler_HOWTO
It (supposedly) enables you to connect without a dialer.

Similar Messages

Internal modem not detecting dial tone

I have an iMac G3 CRT 333MHz (Lime) which is having trouble connecting to my dial-up internet connection. I am fearing that my internal modem is 'burnt out', and am wondering if anyone out there has any additional troubleshooting tips, or any advice on purchasing a new external modem.
The trouble started after a lightning storm, which also disrupted internet connections for my roommate's PC (I don't know exactly how he fixed his, but he is connected via a DSL modem and says he simply restored some modem drivers). I have noticed, however, that he removed his 56k modem...
When I attempt to dial-up from my Mac, I get a message stating "Modem did not detect a dial-tone or the line is currently in use..." I have checked and double checked that the phone line does indeed have a dial tone, and tried connecting through through various outlets throughout the house. I've disconnected all other phone hardware (except the DSL filters) and reached the same result.
I am currently running OSX (10.3.9), and also attempted to dial out after restarting in 9.2.2. (Same result). After that, I dug out my install CD and reinstalled 10.3 (same result)
From each OS, I've run system profiler and recieved no unusual information about the internal modem. The computer definitely senses that I HAVE a modem (Apple Vsn 0007-1,9/2/1998 v.90) That modem simply can't seem to detect the dial tone.
I have also confirmed my modem settings, tried checking and unchecking the 'sound' and 'wait for dial tone' boxes. My internet provider is NetZero, so I have attempted to dial in using their software, as well as directly through Internet Connect. All attempts return the same message. (and the NetZero account is still active, I have accessed it from two separate computers).
Any thoughts out there if there are any further settings or or software/OS variations I should try? Or are my suspicions valid that the storm somehow fried the modem (there were no power interruptions during the storm... only modem troubles)
My next step might be to find an external modem. I've not seen any Mac-compatible 56k modems in stores. There is a Apple USB Modem in the Apple store, but it requires OS 10.4.3 and a computer 'without a built-in modem', so I don't think that will help me. I've also considered using Airport to share my roommate's DSL connection, but I believe that my model of iMac is not airport compatible...
I also have a dead iMac in the closet (DV model) with a blown ethernet port, broken fan, and damaged hard drive. I'm not above cannibalizing either machine to get the other working until I can afford a new G5...
Any thoughts, suggestions, or shared experiences would be greatly appreciated!!

The only thing I can think of is to go in to the modem settings and choose ignore dial-tone. That way even if it's not getting a good tone the iMac will continue to try to connect. This is also important if you have a voice mail system that varies the dialling tone whne you have a message as I know that stops my father's Win98 box connecting to the Internet unless the equivalent option is checked.
You can update your email address to a current one here. If the Apple ID (i.e. the one you login with) is old don't worry that's pretty irrelevant.
mrtotes

Help! Modem Not Detected!

need help. I just got my iMac today and I installed the AOL 5.0 thing. The AOL program isn't detecting the intenal modem. It is V.90 I supose, I do not see the modem cotrol panel in the apple menu. I tried all the apple internal modems form the list, I pluged in the phone line and I is saying Does Not Detect. I am not on my iMac so I can't take any confusing comands right now. Thanks. PLEASE HELP!

Tiger -
Let's try one more thing. Open Macintosh HD. Scroll down to System Folder. Open System Folder and scroll down to Control Panels. Open Control Panels and see if Modem Control Panel is in the lineup. It's probably not since it doesn't show under the 'Apple'.
Just under Control Panels should be Control Panels (Disabled). Open that and see if Modem is in there. If it is, drag it to the closed Control Panels folder and do a restart.
If it's not in the disabled panels folder, do a Sherlock search for Modem and see what comes up. I guess it's possible that the modem panel has been put somewhere else in the HD. If it shows up, drag it to the closed Control Panels folder as above.
If the modem panel is totally absent from the HD, about all I can think of is to perform a Restore using the original CDs that came with the machine. But before that, I'll pose the problem to the larger gang here.
Schadow

Modem Not Detected! UPDATE

Ok I posted this a while ago but I selected my internal modem for AOL V.5.0 (OS 8.6) and it wasn't detected(Trust me I tried everything). Well I was reading my Internal Modem read me amd it sasid that in the modem control panel it should say "Connect via Internal Modem" and mine says "Connect via <no serial ports available>". Ok. I think something fishys going on. I can't select from a list near the Connect via thing. My system profiler says it detects my modem. Can someone help? Please?
In loving memory of TP2GO

I read back through as many of your past posts on this subject as I could find, and there's one subject missing that used to get a lot of posts here. AOL tended to corrupt the Modem Preferences, or replace them ... 'can't remember which.
The clean system install that Ron suggested is probably best, but you can go to the Preferences Folder in your System Folder and throw out the file labled "Modem Preferences", and anything to do with AOL Dialer. Restart the computer and see if there are some selections in your Modem Control Panel.
Instructions for a clean install are on the OS CD in a read-me file.
David

Help! - N80 as a dial-up modem not through GPRS

Does anybody know if it is possible to use the N80 to connect to a laptop for dial-up connection to my ISP. I'm talking about actually dialing a phone number to connect and not through GPRS (tethering). I already got tethering working, I'm just wondering if it is possible to get it to actually dial a phone number to connect. I have a lot of anytime minutes in my Cingular account and want to use them for this purpose. Thanks in advance.
What is the correct AT script to use for this to happen?

I think SIG has the answer, but I tried to find out on their various sites... seems that until you take the Hook, they won't tell you what the Line costs, then the cost of the Sinker will only be revealed once you get the Bill!
I think if they've picked up any traits from down here in GW land, that whatever YOU want to do will cost more than expected, and use the worst option for you!

New internal modem not detected

I installed a US Robotics v.92 faxmodem (model 5660A) into a dual 1.8 G5, 10.4.3. This computer came without an internal modem, but I need to send faxes occasionally.
The modem installed into a PCI slot. In the "About This Mac" apple menu selection, no PCI or modem info appears. I have tried resetting the PRAM, searching the US Robotics and Apple web sites for drivers (nothing for Macs.)
The modem was sold as a Windows and Mac compatible modem. Any suggestions?

Hi Shau,
Welcome to the forum.
USB DSL modems are notoriously buggy when it comes to OSX. Continuous need for updating drivers which, more often than not, cause more problems than they solve. My advice would be to invest in an ethernet adsl router. They do not require drivers, you just plug them in and with a minimum setup (literally seconds) you're up and running. Your ISP may be able to exchange the USB modem with an ethernet adsl router for you at no additional cost. Failing that you can buy one for literally tens of pounds.
More info on routers can be found here:
http://adslguide.org.uk/reviews/
RD

Are there any webcams that work on a dial-up modem with OSX Tiger?

I've seen some discussions about specific webcams, but my problem is I'm on a dialup modem, without broadband. Though webcams exist that will work adequately for me with OS 9.x, there does not appear to be anything anywhere in the market that will work for with Tiger. The closest are the Logitech cams that stop at 10.2. Anybody have any suggestions?
Powermac G5 Mac OS X (10.4.4) dial-up modem. not broadband available (I'm in the sticks)

Firewire cameras are natively supported in OSX.
Many USB cameras are supported using 3rd party
driver
such as <a</div>
href="http://webcam-osx.sourceforge.net/"
target="_blank">maccam.
You can also get drivers from ioxperts
Tim,
Thanks for the quick response. However I was not
asking about digital cameras, I was asking about
webcams. Am I missing something?
Yes you are missing something. I was talking about
firewire webcams doh!
http://www.macworld.com/2003/12/reviews/firewirewebcam
s/
I've been following detailed threads on specific
webcams, and have not seen anyone have success for my
situation.
What do you need a webcam for?
Tim,
Thanks again. I'm learning a lo already by following your suggestions. I have no high-power needs, just basic video chattiing, but I'm in the sticks out here, on a 56K dial-up modem. Can't even get broadband. Many of the cams I've seen require high-speed internet. I can continue searching.
I will mark this question as answered by you, but if you have any particiular cameras to suggest, I will appreciate your inputs. I had already looked at Macworld without success.
brinum

Faxing - Modem Does Not Detect Dial Tone

Hello Everyone,
I suddenly have a need to send and receive a Fax. I have a phone line plugged into the modem port on my G4 and on trying to send a text fax, not much happens. Error message to the effect that the modem is not detecting a dial tone. Same cable that works fine on the phone itself.
Can someone either help with an answer or direct me to a page with more detailed instructions than the "Help" file is providing?
John

I have the same problem. I thought I would begin to use my several years old Powerbook to send a simple fax. As it is I have to use my old G3 to fax. Even with Faxstf pro on I still can't get it to work. Fax STF says that the modem is only set to receive and I just cannot change it in the settings. I've trashed the preferences and the program. I am at a loss after having spent a day trying to figure this out. I am on a dedicated phone line that works just fine. I would really like to just simply fax from my powerbook G4. The modem is as follows:
Modem Model: LastDash
Interface Type: USB
Modulation: V.92
SKU Name: UCJ
Hardware Version: 4.0
Firmware Version: APPLE VERSION 2.6.6
Driver: InternalUSBModem.kext (v2.6.6)
Country: B5 (United States, Latin America)

Internet connection "Does not detect a dial tone" ????

Help!
I have not been able to connect to the internet on my imac G5 for the last couple of weeks. I have tried the usual connect and restart computer and have spoken to my ISP who say it's not to do with them. The message 'does not detect a dial tone' comes up when i try and connect via the modem. I am now at a loss as to what to do. It does appear to be a Mac problem (having spoken to Mac support aswell), but short of re-installing the OS i am not sure what action to take next.
Any help would be greatly appreciated.
Thanks in advance

Welcome to Apple Discussions
Noticed you are running Panther on an iMac G5? Is that correct?
What are your external modem settings in your System Preferences>Network/TCP/IP and modem panels? What changed in your system just prior to your not being able to connect to the Internet?
Short of reinstalling the OS, you can reapply the combo update for the particular version of OS X you are running.
Please post back.

Docsis 2.0 and 1.1 cable modems are not detected via UBR-MC20X20V-5D line card

Hi All,
We have uBR10K series CMTS and recently installed UBR-MC20X20V-5D line card, requirement is to configure this line card to support docsis 1.1 and 2.0. Problem is after finished the configurations modems (Hitron and Motorola) are not detected by the system. means no modem mac address listing under "Show cable modem" command.
Our CMTS has the following components
ESR-PRE2: x1
ESR-PRE-MEM-FD128: x1
UBR10-DTCC: x2
UBR-MC20X20V-5D: x1
iOS version: 12.2(33)SCE3
Part of running-config as follows
cable spectrum-group 13 band 22800000 26600000
controller Integrated-Cable 8/0/0
rf-channel 0 cable downstream channel-id 145
rf-channel 0 frequency 501012500 annex B modulation 256qam interleave 32
rf-channel 0 rf-power 59.0
no rf-channel 0 rf-shutdown
interface Cable8/0/0
no cable packet-cache
cable bundle 1
cable upstream max-ports 4
cable upstream 0 connector 0
cable upstream 0 spectrum-group 13
cable upstream 0 channel-width 3200000 3200000
cable upstream 0 docsis-mode tdma
cable upstream 0 minislot-size 2
cable upstream 0 range-backoff 3 6
cable upstream 0 modulation-profile 21
no cable upstream 0 shutdown
diag output attached herewith. Please any one advice on how to resolve this issue.
Thanks in advance.

Hi All,
We have uBR10K series CMTS and recently installed UBR-MC20X20V-5D line card, requirement is to configure this line card to support docsis 1.1 and 2.0. Problem is after finished the configurations modems (Hitron and Motorola) are not detected by the system. means no modem mac address listing under "Show cable modem" command.
Our CMTS has the following components
ESR-PRE2: x1
ESR-PRE-MEM-FD128: x1
UBR10-DTCC: x2
UBR-MC20X20V-5D: x1
iOS version: 12.2(33)SCE3
Part of running-config as follows
cable spectrum-group 13 band 22800000 26600000
controller Integrated-Cable 8/0/0
rf-channel 0 cable downstream channel-id 145
rf-channel 0 frequency 501012500 annex B modulation 256qam interleave 32
rf-channel 0 rf-power 59.0
no rf-channel 0 rf-shutdown
interface Cable8/0/0
no cable packet-cache
cable bundle 1
cable upstream max-ports 4
cable upstream 0 connector 0
cable upstream 0 spectrum-group 13
cable upstream 0 channel-width 3200000 3200000
cable upstream 0 docsis-mode tdma
cable upstream 0 minislot-size 2
cable upstream 0 range-backoff 3 6
cable upstream 0 modulation-profile 21
no cable upstream 0 shutdown
diag output attached herewith. Please any one advice on how to resolve this issue.
Thanks in advance.

MAC pro 2013 model not detecting E122 USB Modem

Hi,
For some reason, the light of USB modem doesnt glow, and neither is it detected. But when the Mac is restarted, the USB Modem does lit, and shows signs of being detected. Tried downloading Mobile Partner, but since the Modem is not detected, nothing proceeds. It worked well on my Windows PC.

Contact the vendors technical support unit. Because it may work on a PC, it does not follow that it will work on a Mac.
Ciao.

Fax not detected,Comm error, fax run test is all PASS,

Hi Good Day! Im Using a HP color Laserjet Pro MFP M177fw. The Problem is sending fax messages. I do all the updates you need to installed. but the problem with my hp fax machine is still there specially i still receive a fax not detected issue,comm.error, but when i run the fax test run..the result is all PASS. especially the active tel.line,correcrt port on fax machine,tel line current test,dial tone..all the question and are PASS. The firmware is updated like..20140914. Please help me for this kind of problem. Thank You!

Hi @ali_al , I can help you with the fax not being able to send faxes.
Check these settings on the printer:
Confirm the fax number:
Go to setup, fax setup, advanced setup, confirm fax #.
Turn off error correction:
Go to setup, service, fax service, error correction and turn if off.
Set the fax speed to medium:
Go to setup, fax setup, advanced setup, fax speed and select medium.
Turn off the private receive:
Go to setup, fax setup, advanced setup, private receive. Turn it off.
Test the fax.
I have provided a document with some steps to try to see if that will resolve the issue.
Cannot Send or Receive Faxes.
Please provide the following information so I can assist you better.
What type of connection do you have? (Analogue, DSL, Cable Modem)
Are you using the 2 wire phone cable?
Do you have distinctive ring set up on the line?
Is there any voice mail set up?
Do you have a answering machine? (Where is it connected to?)
Where is the fax cable connected to? (modem, wall jack)
Is there a phone also connected the printer?
Have a nice day!
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

Initiate a dial-up connection or detect whether I am connected to the net

I want to initiate a dial-up connection from my java program and also to detect whether I am connected to the internet or not.

well I am developing a proxy server and I want to add
a feature of dial-up demand that detects the current
connection status and if not connected to the net then
call the dial-up dialers in dial-up networking folder
and then connects to the internetI'd say it works like I wrote earlier:
Keep yourself in the proxy-server the connections-status.
If your proxy-server runs on a normal PC, it should be enough to try to connect to the internet.
But do you need control over multiple dial-up dialers etc., this probably isn't enough.
If I can find the time, I'll look into it.
Maybe direct access to the modem is also an option.
That depends on the modem of course and then you probably also need additional scripting. I guess that's not what you're looking for, but if you need info on that, it's probably also an option to look at a wvdial-script on Linux for connection to the internet. It might also be a problem if you have multiple channels for connecting onto the internet (cable,phone,ASDL etc.)

[solved]Nokia 7900 as modem not working

Hi, few years ago, on ubuntu i configured Motorola v3xx for use with wvdial via next /etc/wvdial.conf
[Dialer Defaults]
Modem = /dev/ttyACM0
ISDN = off
Modem Type = Analog Modem
Baud = 460800
Init = ATZ
Init2 =
Init3 = at+cgdcont=1,"IP","internet"
Init4 =
Init5 =
Init6 =
Init7 =
Init8 =
Init9 =
Phone = *99#
Phone1 =
Phone2 =
Phone3 =
Phone4 =
Dial Prefix =
Dial Attempts = 1
Dial Command = ATM1L3DP
Ask Password = off
Password = internet
Username = mobitel
Auto Reconnect = off
Abort on Busy = off
Carrier Check = on
Check Def Route = on
Abort on No Dialtone = on
Stupid Mode = off
Idle Seconds = 0
Auto DNS = on
;Minimize = off
;Dock = off
;Do NOT edit this file by hand!
Now i switched the phone and trying to achieve the same on arch, the connection get's trough:
wvdial ; cat /var/log/messages.log | grep pppd | grep Sent | tail -n 1 >> /data/code/python/gprs/traffic.dat
--> Ignoring malformed input line: ";Do NOT edit this file by hand!"
--> WvDial: Internet dialer version 1.60
--> Cannot get information for serial port.
--> Initializing modem.
--> Sending: ATZ
ATZ
OK
--> Sending: at+cgdcont=1,"IP","internet"
at+cgdcont=1,"IP","internet"
OK
--> Modem initialized.
--> Sending: ATM1L3DP*99#
--> Waiting for carrier.
ATM1L3DP*99#
CONNECT
~[7f]}#@!}!} } }2}#}$@#}!}$}%\}"}&} }*} } g}%~
--> Carrier detected. Waiting for prompt.
~[7f]}#@!}!} } }2}#}$@#}!}$}%\}"}&} }*} } g}%~
--> PPP negotiation detected.
--> Starting pppd at Tue Dec 16 11:41:20 2008
--> Pid of pppd: 17230
--> Using interface ppp0
--> local IP address 10.203.30.115
--> remote IP address 10.6.6.6
--> primary DNS address 213.229.249.161
--> secondary DNS address 193.189.160.13
but I cannot access internet
output of ifconfig (eth0 is wired connection currently):
eth0 Link encap:Ethernet HWaddr 00:1C:23:94:93:85
inet addr:192.168.1.113 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::21c:23ff:fe94:9385/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:13392044 errors:0 dropped:0 overruns:0 frame:0
TX packets:13009772 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:2848145967 (2716.2 Mb) TX bytes:2883455920 (2749.8 Mb)
Interrupt:17
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:1568590 errors:0 dropped:0 overruns:0 frame:0
TX packets:1568590 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:168895651 (161.0 Mb) TX bytes:168895651 (161.0 Mb)
ppp0 Link encap:Point-to-Point Protocol
inet addr:10.203.30.115 P-t-P:10.6.6.6 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1
RX packets:5 errors:0 dropped:0 overruns:0 frame:0
TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:3
RX bytes:74 (74.0 b) TX bytes:107 (107.0 b)
what could I do to make it behave as a modem?
Thanks in advance
Last edited by b4d (2008-12-16 11:31:38)

Does "cannot access internet" mean no access to domain names e.g. can't open google.com, or no access to network e.g. can't ping 74.125.45.100?
If you can ping, but you can't resolve domains, edit your /etc/resolv.conf as required. If you can't ping, check your routing table after connecting.

Photoshop CC 14.1 GPU not detected (MacOS)

So I upgraded to Photoshop CC 14.1 Mid 2009 Macbook, 10.8.4 6GB ram/NVDIA 9400M GPU 236 MB ram.
When I launch PS by itself, my GPU is detected. If I double click on a file, there is a delay in opening and I get this message:
All my OpenGL functions are disabled. So now what can be done to get my GPU working as it did in 14.0?
I'll guess I'm out of luck since NVDIA doesn't issue updated drivers for my GPU.
Just tell me what logfiles you need and how I can get them for you. I'm thinking maybe 14.1 is too much for this system and I'll have to dial back if this is not a bug.
Gene

Trevor.Dennis wrote:
Has anyone had a problem free upgrade to 14.1? If so, what sort of hardware configuration?
No problem here, Trevor.
I'm running Photoshop 12.1 on Windows 7 x64 Ultimate, ATI Radeon HD 7850 with Catalyst 13.4 driver set and so far it's problem-free.
Adobe Photoshop Version: 14.1 (14.1 20130831.r.401 2013/08/31:23:00:00) x64
Operating System: Windows 7 64-bit
Version: 6.1 Service Pack 1
System architecture: Intel CPU Family:6, Model:12, Stepping:2 with MMX, SSE Integer, SSE FP, SSE2, SSE3, SSE4.1, SSE4.2, HyperThreading
Physical processor count: 12
Logical processor count: 24
Processor speed: 3458 MHz
Built-in memory: 49150 MB
Free memory: 43143 MB
Memory available to Photoshop: 44734 MB
Memory used by Photoshop: 95 %
Image tile size: 1024K
Image cache levels: 4
Display: 1
Display Bounds: top=0, left=0, bottom=1200, right=1600
Display: 2
Display Bounds: top=0, left=1600, bottom=1200, right=3200
OpenGL Drawing: Enabled.
OpenGL Allow Old GPUs: Not Detected.
OpenGL Drawing Mode: Advanced
OpenGL Allow Normal Mode: True.
OpenGL Allow Advanced Mode: True.
NumGPUs=2
gpu[0].OGLVersion="3.0"
gpu[0].MemoryMB=0
gpu[0].RectTextureSize=16384
gpu[0].Renderer="AMD Radeon HD 7800 Series"
gpu[0].RendererID=26649
gpu[0].Vendor="ATI Technologies Inc."
gpu[0].VendorID=4098
gpu[0].HasNPOTSupport=1
gpu[0].DriverVersion="3.1.0.0"
gpu[0].DriverDate="20070808000000.000000-000"
gpu[0].CompileProgramGLSL=1
gpu[0].TestFrameBuffer=1
gpu[0].OCLSupported=1
gpu[0].OCLVersion="1.2 AMD-APP (1124.2)"
gpu[0].CUDASupported=0
gpu[0].glGetString[GL_SHADING_LANGUAGE_VERSION]="4.20"
gpu[0].glGetProgramivARB[GL_FRAGMENT_PROGRAM_ARB][GL_MAX_PROGRAM_INSTRUCTIONS_ARB]=[214748 3647]
gpu[0].glGetIntegerv[GL_MAX_TEXTURE_UNITS]=[8]
gpu[0].glGetIntegerv[GL_MAX_COMBINED_TEXTURE_IMAGE_UNITS]=[32]
gpu[0].glGetIntegerv[GL_MAX_VERTEX_TEXTURE_IMAGE_UNITS]=[32]
gpu[0].glGetIntegerv[GL_MAX_TEXTURE_IMAGE_UNITS]=[32]
gpu[0].glGetIntegerv[GL_MAX_DRAW_BUFFERS]=[8]
gpu[0].glGetIntegerv[GL_MAX_VERTEX_UNIFORM_COMPONENTS]=[1024]
gpu[0].glGetIntegerv[GL_MAX_FRAGMENT_UNIFORM_COMPONENTS]=[1024]
gpu[0].glGetIntegerv[GL_MAX_VARYING_FLOATS]=[128]
gpu[0].glGetIntegerv[GL_MAX_VERTEX_ATTRIBS]=[29]
gpu[0].extension[AIF::OGL::GL_ARB_VERTEX_PROGRAM]=1
gpu[0].extension[AIF::OGL::GL_ARB_FRAGMENT_PROGRAM]=1
gpu[0].extension[AIF::OGL::GL_ARB_VERTEX_SHADER]=1
gpu[0].extension[AIF::OGL::GL_ARB_FRAGMENT_SHADER]=1
gpu[0].extension[AIF::OGL::GL_EXT_FRAMEBUFFER_OBJECT]=1
gpu[0].extension[AIF::OGL::GL_ARB_TEXTURE_RECTANGLE]=1
gpu[0].extension[AIF::OGL::GL_ARB_TEXTURE_FLOAT]=1
gpu[0].extension[AIF::OGL::GL_ARB_OCCLUSION_QUERY]=1
gpu[0].extension[AIF::OGL::GL_ARB_VERTEX_BUFFER_OBJECT]=1
gpu[0].extension[AIF::OGL::GL_ARB_SHADER_TEXTURE_LOD]=1
gpu[1].OGLVersion="3.0"
gpu[1].MemoryMB=2048
gpu[1].RectTextureSize=16384
gpu[1].Renderer="AMD Radeon HD 7800 Series"
gpu[1].RendererID=26649
gpu[1].Vendor="ATI Technologies Inc."
gpu[1].VendorID=4098
gpu[1].HasNPOTSupport=1
gpu[1].DriverVersion="12.104.0.0"
gpu[1].Driver="aticfx64.dll,aticfx64.dll,aticfx64.dll,aticfx32,aticfx32,aticfx32,atiumd64. dll,atidxx64.dll,atidxx64.dll,atiumdag,atidxx32,atidxx32,atiumdva,atiumd6a.cap,atitmm64.dl l"
gpu[1].DriverDate="20130328000000.000000-000"
gpu[1].CompileProgramGLSL=1
gpu[1].TestFrameBuffer=1
gpu[1].OCLSupported=1
gpu[1].OCLVersion="1.2 AMD-APP (1124.2)"
gpu[1].CUDASupported=0
gpu[1].glGetString[GL_SHADING_LANGUAGE_VERSION]="4.20"
gpu[1].glGetProgramivARB[GL_FRAGMENT_PROGRAM_ARB][GL_MAX_PROGRAM_INSTRUCTIONS_ARB]=[214748 3647]
gpu[1].glGetIntegerv[GL_MAX_TEXTURE_UNITS]=[8]
gpu[1].glGetIntegerv[GL_MAX_COMBINED_TEXTURE_IMAGE_UNITS]=[32]
gpu[1].glGetIntegerv[GL_MAX_VERTEX_TEXTURE_IMAGE_UNITS]=[32]
gpu[1].glGetIntegerv[GL_MAX_TEXTURE_IMAGE_UNITS]=[32]
gpu[1].glGetIntegerv[GL_MAX_DRAW_BUFFERS]=[8]
gpu[1].glGetIntegerv[GL_MAX_VERTEX_UNIFORM_COMPONENTS]=[1024]
gpu[1].glGetIntegerv[GL_MAX_FRAGMENT_UNIFORM_COMPONENTS]=[1024]
gpu[1].glGetIntegerv[GL_MAX_VARYING_FLOATS]=[128]
gpu[1].glGetIntegerv[GL_MAX_VERTEX_ATTRIBS]=[29]
gpu[1].extension[AIF::OGL::GL_ARB_VERTEX_PROGRAM]=1
gpu[1].extension[AIF::OGL::GL_ARB_FRAGMENT_PROGRAM]=1
gpu[1].extension[AIF::OGL::GL_ARB_VERTEX_SHADER]=1
gpu[1].extension[AIF::OGL::GL_ARB_FRAGMENT_SHADER]=1
gpu[1].extension[AIF::OGL::GL_EXT_FRAMEBUFFER_OBJECT]=1
gpu[1].extension[AIF::OGL::GL_ARB_TEXTURE_RECTANGLE]=1
gpu[1].extension[AIF::OGL::GL_ARB_TEXTURE_FLOAT]=1
gpu[1].extension[AIF::OGL::GL_ARB_OCCLUSION_QUERY]=1
gpu[1].extension[AIF::OGL::GL_ARB_VERTEX_BUFFER_OBJECT]=1
gpu[1].extension[AIF::OGL::GL_ARB_SHADER_TEXTURE_LOD]=1
Serial number: ....................
Application folder: C:\Program Files\Adobe\Adobe Photoshop CC (64 Bit)\
Temporary file path: C:\TEMP\
Photoshop scratch has async I/O enabled
Scratch volume(s):
C:\, 1.75T, 719.4G free
Required Plug-ins folder: C:\Program Files\Adobe\Adobe Photoshop CC (64 Bit)\Required\Plug-Ins\
Primary Plug-ins folder: C:\Program Files\Adobe\Adobe Photoshop CC (64 Bit)\Plug-ins\
-Noel

Dial-up Modem not detected

Similar Messages

Maybe you are looking for