Dialer remote-name - what is it for?

Hello there,
ISDN dial-up. One of Dialer's interfaces.
I don't understand one thing - what "dialer remote-name remotename" is used for ?
I understand that when router dials out for authentication it either uses its hostname or "ppp chap hostname HOSTNAME"
So what does dialer remote-name stand for ? Is it like expected remote host name or what?
Thanks,
Alex

Hi Alex,
First of all see the follwoing link about PPP CHAP Authentication :
http://www.cisco.com/en/US/tech/tk713/tk507/technologies_tech_note09186a00800b4131.shtml
then see :
http://www.cisco.com/warp/public/793/access_dial/ddr_dialer_profile.html#conf
that's an example of DDR and CHAP authentication through BRI interfaces.
be aware at CHAP authentication when two hosts are going to connect together, they should have same password at each side, it means password must be same on both routers.
so when you define dialer remote-name at dialing out interface, it tells to router to use appropriate password to challenge to remote host, also at the remote router (dialing in), the dialer remote-name specify the dialer profile to use.
Hope this helps.
Regards,
Mehrdad Arshad Rad

Similar Messages

  • HT5306 I do not want to give remote access to anyone but myself as privacy is my friend.  Can this remote desktop software still be for me personally unless I allow access and for my MAC lap top only?  What if I do not update? compatibility issues with wh

    Hello:
    Thank you for the update for remote access for desktops.
    Personally, I do not want to give remote access to anyone but myself as privacy is my friend.  Can this remote desktop software still be for me personally unless I allow access and for my MAC lap top only?  What if I do not update? I do use this lap top in other countries.  compatibility issues with what?

    Apple Remote Desktop is off be default. It has to be enabled for some one to be able to remotely connect to the computer. And then, you still have to have a user name and password on the computer to remotely connect with.
    If you want to see if remote access has is enabled for Apple Remote Desktop; you can find the setting in, Apple Menu, System Prefrences, Sharing. If it's enabled, Remote Management or Screen Sharing will be checked.
    Beucase Apple Remote Desktop Agent is part of the Mac Operating System; even if your not using it, Apple Software Updates will from time to time offer updates for ARD Agent. Software Updates can some times be stacked ontop of each other; so chosing not to install an update, can mean other updates you may want may not be offered. At least until you install the updates those updates require. Also software updates can improve the security of your computer.

  • What host name do I use for Hotmail incoming mail server?

    What host name do I use for Hotmail incoming mail server?

    Access the homescreen and tap "Settings."
    Go to "Mail, Contacts, and Calendars" and tap "Add Account." Your iPhone should display a list of email service providers. Even though you are setting up a Hotmail account, you will be doing it first through Gmail on your iPhone. Tap the Gmail icon to create a new account. Enter your name and a user name and password for the new Hotmail account you will be making later. Enter "imap.gmail.com" in the "HostName" column. Press the "Save" button at the upper right corner of the screen.
    Enter your name, email address, password, and the description of the account. Next, click "Save." You should now be able to check your email from the homescreen.
    Enter "smtp.gmail.com" in the "Outgoing Mail Server." Enter the password for this Gmail account in the "Password" column. Enter user name for this Gmail account in the "UserName" column. Press the "Save" button at the upper right corner of the screen. Press the "Home" button to return to the iPhone's home screen.
    Use the Web browser to go to Hotmail.com and create a new account. Use the user name and password for the account that you entered into the Gmail account on the iPhone earlier. Click on “Settings” after the account has been created.
    Click on the "Settings" tab. Click on the "Forwarding" tab. Click on the "Pop/IMAP" tab and select "Enable IMAP." Click on the "Save” button. Click on “Settings” and select “Accounts” and then “Add Another Email Address” from the webpage. Enter the name of your existing Hotmail account in the column. Press “Save.”
    Go to the inbox. Open the message from Gmail and click on the link in the message box. Select the “Options” tab and check the “Forwarding email” box.
    Send yourself a message to your Hotmail account from an email client. Click on the icon of the Mail program at the bottom of the iPhone’s screen. The email you sent to Hotmail will appear in the inbox of the Gmail account in the iPhone's email.

  • Have v10.6.8 and iMac performs slowly, spirals for very long periods, feels like back to dial-up. What can I do?

    Have v10.6.8 and iMac performs slowly, spirals for very long periods, feels like I'm back to dial-up. What can I do to speed things up?

    How large is you HD and how much space do you have left?
    Check out the following & do the necessary: 
    User Tip:  Why is my computer slow?
    What to do when your computer is too slow
    Speeding up your Mac

  • What are rule for adding names to photos?

    what are rule for adding names to photos in iphoto?

    Since your profile indicates you have a Mac, I am guessing you are asking how to add a face name using iPhoto on your Mac.
    You would open the photo in iPhoto, click "Info" on the bottom, and then the "Faces" tab on the right.
    Once you have added the face name in iPhoto on your Mac, once you sync the photo to your iPhone, the name will appear there as well.

  • HT1202 How do i change the computer for my iphone? it says iphone will syn automatically once it is plugged into "DUCH..." (not my computer name) . what should i do to change that?

    How do i change the computer for my iphone? it says iphone will syn automatically once it is plugged into "DUCH..." (not my computer name) . what should i do to change that?

    Connect your phone to iTunes and in the Summary pane, hit the "Sync with this iOS device over Wi-Fi"
    http://support.apple.com/kb/PH2560

  • On my ipod touch, when i go on my game it pops up with a message saying "FlurryAppCircle: Attempting to pass blank hook name to getOffer. Please use a non-blank string for hook name" what does it mean?

    on my ipod touch, when i go on my game it pops up with a message saying "FlurryAppCircle: Attempting to pass blank hook name to getOffer. Please use a non-blank string for hook name" what does it mean?

    Try:
    iOS: Troubleshooting applications purchased from the App Store
    Contact developer/go to their support site.

  • Not sure about "dialer map name" purpose

    Hello,
    I am trying to understand the purpose of the "dialer map name <hostname>" command in dialer and ISDN interface configurations, i.e., what is the reason and usage of this name mapping. Unfortunately, looking into IOS command guides and references did not help me much.
    The documentation seems to suggest that this mapping is used to define a remote host name for authentication purposes. However, I don't understand why this would be necessary - both PAP and CHAP in PPP will provide the remote name whenever needed so there is no reason to explicitly specify the remote host name.
    If anyone could help me with this issue I would be most grateful. Thanks in advance!
    Best regards,
    Peter

    Hello,
    If your using bri to bri connections the dialer map name will be used by default as the username if not specified in ppp exteded settings. If I remember right.
    Patrick

  • RSA1 error  Logical system name has been changed for this system

    Hello All,
    Earlier the RSA1 was activated for client 300 on our crm 5.2. after that we changed the client to 500 using SE16 -> Type table RSADMINA / Check Colum BWMANDT -> 500.
    But now when we login to client 500 and execute RSA1 it is showing
    Logical system name has been changed for this system"
    In scc4 we have not made any changes. Can you tell what should be done ? in the pop up it is showing following steps
    Change the name of the logical system (table T000) for client back to SIDCLNT300. This enables you to continue working with the system.
    If you really want to change the logical name, than you can, if and when you:
    change the system name back to SIDCLNT300,
    delete all existing connections between this system and other systems,
    delete all transfer structures that still exist, and
    do not use ALE or Workflow.
    Guys do you know how to fix this ? .
    Also do you know Assignment of Source System to Source System ID (table RSSOURSYSTEM) using RSA1 ?
    Edited by: Sahad K on Mar 17, 2008 10:55 AM

    Hello Hari,
    Both the options you said  cannot be used
    since the logical system SIDCLNT300 is used by client 300 and it cannot be given to client 500.  Also there already exist a logical system SIDCLNT500 which is assigned to client 500.
    I found out the issue. In the table RSBASIDOC  the logical system name that can use rsa1( bw  client )is set as  SIDCLNT300).  Only if we delete that entry and set it to SIDCLNT500 ( 500) we can use it on client 500.
    The solution is specified in /message/3284842#3284842 [original link is broken]
    Let me try the solution 2 and inform you.
    Solution 2:
    You cannot delete the source system. Two cases have to be distinguished:
    The source system still exists.
    Switch to Transaction SM59. Find the destination which has the same name as the logical system of the source system from field SLOGSYS in table RSBASIDOC (see above).
    Such a destination does not exist in Transaction SM59. In this case, you have to create the destination to the source system. Name the destination equal the entry in SLOGSYS from above. Then return to the Administrator Workbench and repeat the deletion.
    The entry exists but a remote login is not possible. Correct the communication parameters.
    Everything works. Change to Transaction SE37, function module RSAR_LOGICAL_SYSTEM_DELETE, Sngl. test. Parameter I_LOGSYS = <log. name of the source system>, I_FORCE_DELETE = 'X'.
    The source system no longer exists or was replaced with another source system with the same IP address.
    Proceed as described in the first case but make sure, that the field 'Target host' contains a not existing server in the maintenance screen of the destination (Transaction SM59). If necessary, change an existing entry. Later when you delete, the system asks you whether you want to delete, although the source system is not available. Select 'Ignore'.
    Incase you have any idea other than this please let me know how to edit the RSBASIDOC table  and change the entry to client 500.
    Edited by: Sahad K on Mar 18, 2008 5:07 AM

  • Cannot Create New Share from Azure PowerShell - The remote name could not be resolved

    I have created a storage account. It seems that there isn't a specific way to create file storage rather than blob storage.
    I followed the instruction for creating a share in Azure Power Shell but when I try $s=New-AzureStorageShare... I keep getting the error "The remote name could not be resolved".  I checked the account name and it matched what is shown on the
    Azure site.
    I also cannot access the storage from the URL's.  I get the message "This page can't be displayed.
    How can I create a file storage account and a share to it?
    Thanks,
    Glen

    Hi Glen,
    Thanks for your post!
    Did you sign up your File Service ?
    To sign up, go to the Microsoft Azure Preview Portal, and sign up for the Microsoft Azure Files service using one or more of your subscriptions. As subscriptions
    are approved for the Azure File preview, you will get an email notifying you of the approval. We will be slowly opening up the service to users in batches, so please be patient after signing up.
    After sign up and enable this feature, I suggest you could refer to this blog for how to use Azure File service (
    http://blogs.msdn.com/b/windowsazurestorage/archive/2014/05/12/introducing-microsoft-azure-file-service.aspx#faq7 ).
    Regards,
    Will
    We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
    Click
    HERE to participate the survey.

  • I have configure remote access feature web application proxy but not configure give the error. The remote name could not be resolved.

    I have configure remote access feature web application proxy but not configure give the error. The remote name could not be resolved in server 2012 R2.
    I have configure Ad and ADFS different server and try to configure web application proxy different server. what setting are required for connect web application proxy to Ad and ADFS.

    Hi,
    In addition, please make sure that the port 443 is not blocked by the firewall.
    Web Application Proxy requires internal name resolution to resolve the names of backend servers, and AD FS servers. When publishing web applications via Web Application Proxy, every web application you publish requires an external URL. For clients to reach
    these web applications, a public DNS server must be able to resolve each external URL that you configure. Note that the external URL must resolve to the same IP address as the Web Application Proxy server, or the external IP address of a firewall or load-balancer
    placed in front of the Web Application Proxy server.
    Best regards,
    Susie
    Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected]

  • The remote name could not be resolved

    We are running Office 365 Power BI (as a trial) and published our data through the data manager gateway service.
    We are able to retrieve a list of shared tables / views through Power Query in Excel 2013 Professional Plus.
    However, when clicking on edit on any table returned we get this error in the Power Query window:
    DataSource.Error: OData: Request failed (NameResolutionFailure):
    The remote name could not be resolved: 'SERVER-NAME.DOMAIN.local'
    Details: https://POWERBISITE.hybridproxy.powerbi.com/ODataService/v1....
    I have tried configuring the Data Manager Gateway service to run HTTP (at first) and HTTPS.
    Could this be a port number issue? Or what else?
    Appreciate any help, Thank you
    Ian

    Hi intrasight,
    I gave the hosts thing a try.
    I was getting 'unable to resolve' errors in attempting to use Power Query in a small stand-alone test domain (all computers are in the domain, and in this little LAN).  So I edited
    hosts in C:\Windows\System32\drivers\etc
    I added this line: 
    192.168.0.4 mycomputer.ad.mydomain.com
    mycomputer is the name of the computer running the Data Management Gateway, and
    ad.mydomain.com is the name of the domain.
    Now, I get
    <textarea class="role-selectableText" cols="1" readonly="readonly" rows="1" style="width:659px;height:87px;" tabindex="-1">DataSource.Error: OData: Request failed: The underlying connection was closed: Could not establish trust relationship for the SSL/TLS
    secure channel. Details: https://mydomain.hybridproxy.powerbi.com/ODataService/v1.0/mydatasource</textarea>
    Which tells me that hosts on the client is indeed now resolving the name/IP correctly, and Power Query is  finding the DMG directly (rather than via the
    hybridproxy.powerbi.com cloud service).
    But that's terrible!  
    A) I shouldn't need to use hosts since
    B) the hybridpproxy cloud service is finding the DMG on my database machine (because the Test Connection works OK) 
    C) but without hosts the client Power Query says that "The remote name could not be resolved"
    DataSource.Error: OData: Request failed: The remote name could not be resolved: 'mycomputer.ad.mydomain.com'
    Details:
    https://mydomain.hybridproxy.powerbi.com/ODataService/v1.0/mydatasource
    There's no way an actual production system should require editing
    hosts on all client machines.
    So to my mind, the original question is still outstanding. 
    How do I get Power Query to resolve the remote name?
    Cheers, Donna
    Donna Kelly

  • Firefox has remberd a password to a website ... chessatwork and I get loged in to my main page and when I click on any link it takes me right back to my log in page, where it has it stored.... password and user name,,, whats up and how do I turn that off?

    Firefox has remberd a password to a website ... chessatwork and I get loged in to my main page and when I click on any link it takes me right back to my log in page, where it has it stored.... password and user name,,, whats up and how do I turn that off? chessatwork has ran great for me for many yrs, then one day I down loaded firefox and went to play chess on this site chessatwork.com, well the window popped up asking to remember the log in and pass word and so I said ok, and it did, but now when I click log in and I go to my main page (home) and click on any link, say to play game I return right back to log in

    See http://kb.mozillazine.org/Deleting_autocomplete_entries<br />
    Remove a saved password here: Tools > Options > Security: Passwords: "Saved Passwords" > "Show Passwords"
    You may also need to remove the cookies from that website.<br />
    * Tools > Options > Privacy > Cookies: "Show Cookies"

  • When i go to 'New Folder' the name box only opens for a second so I dont have time to name it correctly. Rename Folder does the same thing - any thoughts??

    when i go to 'New Folder' in outlook the name box only opens for a second so I don't have time to name it correctly. Rename Folder does the same thing. Any thoughts? Many thanks.

    Hi Clint,
    Did you get a reply from anyone for this problem?  I'm having the same problem and wondering what the resolution might be.
    Thanks

  • What to look for in free fonts?

    I want to download some free fonts (I am a student) to use for some 300ppi print pieces and am wondering what to look for in a free font to determine whether it will print nicely at a high quality. What makes a good quality font? I know there is lots of garbage out there though there are also many good quality free fonts.
    Thanks.

    This is not remotely a Photoshop question.
    Try the Adobe Typography forum:
    http://forums.adobe.com/community/design_development/typography

Maybe you are looking for