Dialin to 3845, giving IP address of VLAN on another switch

Boy that title was hard to write.
Basically this is what I have:
1. a user dialing into a 3845 router via NM-16AM-V2 socket (async).
2. the user gets an IP address from local pool. (192.168.1.?)
3. the router is connected through a trunk to a Catalyst 3550.
4. on the Catalyst 3550, there exist three vlans (20 network, 172 network and 192 network).
The user can ping the 172 network on the switch and the 20 network on the switch. However, it cannot ping the user on the 192 network on the switch. (192.168.1.10).
Any ideas??

hi
can you post your config of your router without the sensitive infos filtered??
regds

Similar Messages

Error on invoking a webservice by giving ip address instead of local host

Hi,
I created a web service through jdeveloper and tried accessing the webservice generated WSDl file by giving ip address of my machine , but it throws me an error stating IE cannot display the web page . The same web service is running fine when giving local host on the Web service URL .
Looking frwd fr sme help
Thanks in advance
Ragaven

Hi,
your WebLogic server is not setup to listen for the IP address. You can change this in the WLS console for the server configuration. Note that when you install WLS and don't define any hostname then it will listen to all addresses (which also is the default for the integrated WLS)
Frank

HSRP - Duplicate address on Vlan, sourced by mac-address

Hi ,
Network structure
Switch A --- Customer firewall 1
|
Switch B --- Customer firewall2
May be some one can help me.
There was a nagious alert yesterday and on investigation I found the 'Duplicate address x.x.x.x(VIP) on Vlanxxx, sourced by 0006.b19c.c5d9' error
It a HA feed from our switches which is going to customer firewalls.
On further investigation I have found on our switch A the ARP table is not learning the VIP address from this mac-address where as on switch B is learning the VIP address through mac 0006.b10c.c8d9 which is customer sonic firewall which is not a normal behaviour.
Our switches are Cisco 3560 switch.
Please if you could let me know what causing this.

Hi mcgowan,
Yes, there is duplicate MAC. But, its duplicate between interface vlan address and virtual MAC address on HSRP.
when I type command :
show mac address | i 0000.0c07.ac01
It shows me :
100 0000.0c07.ac01 STATIC CPU
I think this MAC generate by system on HSRP. Currently I shutdown interface vlan 100 on switch A, like as your suggestion. But the impact is my client will get trouble when switch B is down, because HSRP is not running well.
Regards,
Rakhmad

Detailed Navigation not displaying giving ip address instead of hostname

Hi
I created applications in web dynpro.So i imported in the Enterprise Portal.
In that I created Role----Under That Worksets (X ,Y ,Z, W) -For each workset I created more than 4 Pages to that---For each page i added Iview.
I added "IP Address" and "HostName" in the c:/windows/system32/drivers/etc/host
Then i login into the Portal with normal URL
http://<HostName>:50000/irj/portal
So its Displaying.....Up to this its fine...
If suppose i want to login with
http://<IP Address>:50000/irj/portal....Under Each Workset, one page is showing,,,means one Iview is Visible...means Detailed Navigation is not showing.
All Pages are not visible...
Please any one help me to do this....
So its not possible to say to anyone ,,,,u have to add this ip Addrss in the path.
Please Provide the Permanent solution ,,even by giving IP address also all pages and Iviews must see..
Regards
Sushma

Hi Sushma,
I am not sure if the same apply when you access the URL through the IP. The SAP BI works on the concept of Fully Qualified domain names for access and also there is a system of web dispatchers which are configured for the domain name to handle report requests.
Also with portal in place you will not be able to see the URL of the application running within portal
for example the URL we see are
ttp://<xyz>.com/irj/portal but then the individual URLs for the applications running within the portal cannot be seen...due to security reasons.
That could be the possible case.
Regarding Use of Portal at client place:
1. You can use the VPN connectivity. You will only need to give the access rights to the perticular id & that will be all.
2. Assign the portal port to the some global address. That will work.
But, I suggest, VPN is better.
Regards
Chander Kararia
Edited by: Chander Kararia on Feb 6, 2009 11:10 AM

How to use different Vlans outside another gateway in sg-300 28?

dear all
how shall i use different vlans outside another gateway in sg-300 28?
Example:
vlan2 192.168.2.0/24 gateway 192.168.2.1 outside router gateway 192.168.2.254
vlan3 192.168.3.0/24 gateway 192.168.3.1 outside router gateway 192.168.3.254
should me doing in sg-300 28?
thanks.

Hi Amin,
Leave the switch in Layer 2 mode
Cable VLAN2 to the to the outside router gateway 192.168.2.254 interface
cable VLAN3 to the to the outside router gateway 192.168.3.254 interface
Excuse the rough diagram
Make the port going to the outside router gateway, untagged in the vlans they will be transporting. (I am assuming that the router gateway is not vlan aware.)
IP hosts will most likely get DHCP from the router gateway. The IP hosts will then automatically send IP traffic to the router gateway.
VLAN 1 in my switch, could then be the only interface within the switch that has a IP address associated with it, for management purposes.
I can see from you post, that English is not your first language, if you want to speak to someone, you can ask a question by going to;
www.cisco.com/go/sbsc
regards Dave

How to add the IP address helper command to the switch

Hi
I am trouble shooting a SF 200-48P and I am a bit lost without a CLI not used to the GUI. What I need to know is how to add the IP address helper command to the switch?
I have a number of IP phones which are not getting an IP address from DHCP (PCs which are diasy chained off the phones are all working correctly). On the higher end switches I would have added the IP address helper command to the VLAN and that would have sorted it. However I can't seem to figure out how to do this on the small business switch.
Thanks
Lorne

Thanks Rizwan. I was banging my head wishing they weren't small business switches as I felt lost without the command line!
Lorne Gallagher | McCann FitzGerald Solicitors | Riverside One, Sir John Rogerson's Quay, Dublin 2, Ireland | DDI +353 1 607 1726 | Fax +353 1 829 0010 | www.mccannfitzgerald.ie
Ireland Law Firm of the Year 2011 | Chambers Europe
Ireland Law Firm of the Year 2011 | International Financial Law Review

Adding subnet IP range to VLAN in SGE2000P switch

hi,
I am unable to add subnet IP range to VLAN in SGE2000P switch. Can anyone help me to configure same. Thanks in advance
I want to configure 3 VLAN in my SGE2000P switch. as a router I am using my Fortigate firewall 50b. I have done all required configuration in switch but till I am unable to assign subnet range to switch.

i am using ios version v1.2.7.7 (latest)
i tried the following CLI commands
switch(config)# vlan 2
switch(config)# interface vlan 2
switch(config-if)# name project2
switch(config-if)# ip address 192.168.10.2 255.255.255.0
so as and when i press ENTER on the ip address line , the switch stopes responding. i tried changing vlan number and name but no luck.
it already has vlan 1 , with default ip address 192.168.1.254 , i cannot ping this IP after this.
pls suggest...

Help config vlan and inter routing vlan on 2 switches SF300-24 ???

Dear Cisco!
now we have 2 switches: SF300-24
on one SF300-24 we config it at layer 3 mode with VLAN configuration same as following
VLAN ID 2 (ports: 2 -6) have ip interface 192.168.2.254/24
VLAN ID 3 (ports: 7 - 10) have ip interface 192.168.3.254/24
VLAN ID 4 (ports 11- 15 ) have ip interface 192.168.4.254/24
and VLAN 1 default have IP address: 192.168.1.200
DHCP relay - DHCP server 192.168.3.1
- DHCP relay: VLAN2; VLAN3; VLAN4
ip route: 0.0.0.0 0.0.0.0 192.168.3.1
all ports of VLAN2, VLAN3, VLAN4 set access mode.
and another SF300-24
was configed at layer 2. We config VLAN ID 2 ̣̣̣have ports 2 -6; VLAN ID 3 ports 7 -10; VLAN ID 4 port 11-15 ,too.
And we use port 26 on 2 switches SF300-24 is trunk mode then we connect both SF300-24 switches.
But on SF300-24 layer 2 cann't inderstand VLAN from Sf300-24 layer 3!!!
Could you please help me check this situation?
How to config VLAN on 2 switches SF300-24 Layer 3 and SF300-24 layer 2?
Thanks!
See you soon!

Son Nquyen,
First i would upgrade to 1.1.8 since the 1.0.0.27 was beta code.
Next when when connecting both switches together each port will need set via Trunk mode with proper native vlan and tagged vlan traffic. What's the configuration of your trunk ports on each switch?
Thanks,
Jasbryan.

I am trying to change my Apple ID. Try to do this I keep getting an error message saying 'This email address is designated as your rescue email address and cannot be used as your Apple ID or Primary email address. Please choose another.' The email address

I am trying to change my Apple ID. Try to do this I keep getting an error message saying ‘This email address is designated as your rescue email address and cannot be used as your Apple ID or Primary email address. Please choose another.’ The email address that I want to use did use to be my recovery email but I have changed it, so that address is no lonegr associated with my account. I do not understand why I cannot use it as my Apple ID now. Can anyone help?

Contact iTunes customer support for assistance.

Two VLANs on one switch port?

Currently we have the following
Cat 4003 with VLAN trunking turned on to multiple switches. Each port in those exterior switches is assigned to a vlan(we have about 60 different vlans).
What I would like to do is on those exterior switches have two vlans assigned to it.
We'd like to create a single IP Phone VLAN(let's call it 999) that can span our entire enterprise and would have dhcp deployed on it.
Each port is connected to an IP phone which has a 2 port switch in them. One port to the wall, one to the pc.
The switch ports on those phones support vlan tagging
How would setup an exterior switch to access 2 vlans that connect to 2 port switch on an IP phone?

To facilitate ease of deployment, use VTP so that you can centrally create the vlans and propagate to each exterior switch. Now I believe you already do have a layer 3 engine or router that does routing between all these vlans. What switches are used on teh exterior ? This is to find out if voice vlan support is available.
In cat switches, voice vlan is created using command,
set port auxiliaryvlan vlan
In IOS based switches,
int fa0/1
switchport mode trunk
switchport trunk encap dot1q
switchport trunk native vlan
switchport voice vlan
switchport priority cos extend 0
or
int fa0/1
switchport mode access
switchport access vlan
switchport voice vlan
I am not sure about support of voice/aux vlan in 4003. We will have check your other switch models/ software versions to determine support for this command.

VLAN between SFE2000P switches

Dear friends,
I've connected two sites with the following configuration:
Site 1:
Stack Linksys SFE2000P - Firmware version 1.0.0.X
Port 1/g3 connected to a FO link to site 2
Oficina 2:
Stack Linksys SFE2000P - Firmware version 3.0.0.X
Port 1/g3 connected to a FO link to site1
I've tried to create a VLAN to communicate only a few ports of both sites:
4/e23 y 4/e24 of site 1
7/e23 y 7/e24 of site 2
To do this, I tried the following:
Port 1/g3 (site1) -> VLAN 50 (tagged) - Trunk
Port 1/g3 (site 2) -> VLAN 50 (tagged) - Trunk
Port 4/e23 y 4/e24 (site1) -> VLAN 50 (untagged)
Port 7/e23 y 7/e24 (site 2) -> VLAN 50 (untagged)
It doesn't work!!!. In the same stack of each site it works without problems. Could you help me??? There is some misconfiguration???
I've stablished other VLANs between Linksys and 3Com Switches, but now it doesn't work at all.
Thanks in advance!

I Did find a same article on this forum. Maybe this would help you. an article coming from GV.
* access mode: an access mode port connects to a normal device like a desktop, printer, or similar. An access mode port can be member of a single VLAN only, i.e. you have to decide to which VLAN it is supposed to belong to. In your case, you configure an access mode port for either VLAN 10 or VLAN 20.
With a single switch things are clear now: some ports are VLAN 10 and some ports are VLAN 20. VLAN 10 can talk to each other. VLAN 20 can talk to each other. No traffic passes between VLAN 10 and VLAN 20.
Of course, now you want to connect this switch to some other network devices, in particular the second SRW because you need additional ports or you have an additional location. And there is the ASA which provides internet access for these VLANs.
* trunk mode: This is where trunk mode comes in. A trunk mode port can carry multiple VLANs on a single port. This is done using 802.1q tags. 802.1q tagged ethernet frames have an additional field for the VLAN to which the frame belongs to. With this, a switch can send frames for VLAN 10 and VLAN 20 through a single port to another switch or router. Each frame sent is tagged with 10 or 20 depending on which VLAN the frame belongs to. The receiver will accept each frame and assign it to the corresponding VLAN on the receiving side. This way the receiving switch or router is able to keep those VLANs strictly separated.
So let's say you want two VLANs 10 & 20 in your network. You would create VLANs 10 & 20 on your ASA and both SRWs. (Create only means that the device knows this VLAN exists and is able to handle traffic for this VLAN). You would configure LAN port 1 of your ASA as trunk with members VLAN 10 & 20. You configure port 1 & 24 of your first SRW in trunk mode with members VLAN 10 & 20. You configure port 1 of your second SRW in trunk mode with members VLAN 10 & 20. Now you wire port 1 of your ASA to port 1 of your first SRW. Then you wire port 24 of your first SRW to port 1 of your second SRW.
This creates the VLAN trunk through your network. Traffic in both VLANs can travel through this trunk between the switches and to the ASA and from there, if properly routed, into the internet.
here is the Link
As the SFE2000P is now part of Cisco Small Business I would recommend you ask your question in the Cisco Small Business Support Community. There are a few Cisco people over there which maybe able to reproduce your problem in a lab environment and check with the developers...

Do I need to create ip address to another switch when i use stack?

Good Day!
Please help me to answer this question in my title. I have 2 switches my old switch has configure ip address and i will use stack to my another switch the old one will be the primary and new switch is the secondary do i need to configure the ip address of the new 1 or no need? i'm totally confuse on it. I hope you can help me regarding on this matter.Thank you.

no Need.
Here is the procedure:
Tips to Add a Switch as a Slave to the Stack
To add a switch, as a slave, to a stack, complete these steps:
Note: Make sure the switch that you add into the stack has the same IOS version as the switches in the stack. Refer to Catalyst 3750 Software Upgrade in a Stack Configuration with Use of the Command-Line Interface to upgrade the IOS in a catalyst 3750 switch.
Change the switch priority of the switch to be added to "1".switch stack-member-number priority new-priority-valueNote: This step is optional, but it will make sure that the switch has fewer chances to become a stackmaster in the future.
Power off the switch that is to be added.
Make sure that the stack is fully connected so that, when you connect the new switch, the stack will be at least in half connectivity and does not partition.
Connect the new switch to the stack with the StackWise ports.
Power on the newly added switch.
After the new switch comes up, issue the command show switch to verify stack membership.
HTH
Regards
Inayath
***********Plz dont forget to rate all usefull posts*********

Creating multiple vlans across multiple switches

Hi All,
How should I create multiple vlans across multiple switches?
For instance, I have two (primary/redudant) layer 3 (core) switches and four layer 2 access switches (Cisco 2960) for the hosts, and given these are the vlans/subnets to be created. Should I do it in the core switches only and it would just propagate through the access via VTP? Just trying to practice and learn.. Any help will be greatly appreciated:)
VLAN 100: [DHCP-workstations]
172.26.4.0/24
172.26.5.0/24
VLAN 200: [Servers]
172.16.1.0/24
172.16.2.0/24
VLAN 300: [Printers]
192.168.129.0/24
192.168.130.0/24
VLAN 800: [Management for switches/routers]
10.160.1.0/24

Hi
You will have the SVI on the core. Set a VTP domain, make one of the cores as VTP server and rest of the switches as VTP clients. Once you do this, you won't have to login into each switch and create a vlan locally. The vlans will be automatically advertised from the VTP server to all the VTP clients.
Thanks
Ankur
"Please rate the post if found useful"

Spanning vlans across access switches in distribution block.... please help

Hi All
Can someone please explain why Cisco states that in a Campus Hierarchical modle if Vlans are spanned across Access switches in a distribution block, then the Distrubution to distribution link should be Layer 2. Is this really necesary or just a recommendation, and if so why? Can't this link be a L3 link when spanning vlans across Access switches in distribution block, as I understand the benefit of having a L3 distribution to distribution link so that SPT is avoided.
Please help

Hello,
The cisco recommended design is L3 links, but these is only possible if you have no vlans you need to span over the hole network.
It depends on your topology or what you want achieve.
If you need for one or more vlan's spanned the LAN, you need to use a layer 2 connection between all switches and between distribution too.
In my company we have for example a few vlans for restricted areas, like device management or else, so we can't use L3 Links in the distribution area because these vlan's are terminated at the firewall. I think these is good thing.
I would recommend you if you don't have to span one or more vlan's across the network to use L3 Links, specially in the case of redundancy way's. So you need no spanning-tree, but need to use other protocols like GLBP or else. The works faster and are not so confusing (for some people) as STP.
best regards,
Sebastian

How to search/Scan Vlan of cisco switch ports

Can any one tell me how i can scan/search vlans of cisco switch port through any monitoring tool (orion/solarwinds).
Consider this scenario as i have no access to switch and i want to know below things:
1-Vlans created on switch?
2-which switch port belongs to which vlan id?
Thanks

Hi,
You can do it only with hub in between and also please note that when sniffing with Wireshark on Windows the OS would remove VLAN tag so you may need to use Linux machine.
Regards,
Aleksandra

Dialin to 3845, giving IP address of VLAN on another switch

Similar Messages

Maybe you are looking for