Diamond - 4870 Installed ...... but system will not boot - no display..

Finally got my special 6-pin PCI std. connector to a MAC PRO 6-pin smaller power connector.
The ATI-X1900 works like a champ, when I remove it an install the Diamond ATI-4870 (MAC VERSION) in and connect the two power blocks on the motherboard, the system beeps like it is booting, but I do not get any output from the ATI-4870 card. The 4870's fan is running and it sounds like the system is booting, but it never displays anything.
Any Ideas ??
Message was edited by: bketrick

Return it for the 5770.
http://store.apple.com/us/browse/home/shopmac/mac_accessories/displays?n=graphiccards

Similar Messages

System will not boot up

MB: KT6 Delta-LSR
CPU: XP2500 Barton
GFX: Asus V9520 Magic/T 128mb
RAM: 1028 pc3200 ddr400 (2x512) Geil Branded
HDD: Maxtor 40GB 2mb Buffer
Put it all together formatted the HDD, installed windows, network was working perfectly. (on ASUS via600 board)
Next day turn it on and nothing, zilch not even a flashing cursor top left of screen, dont even boot to DOS. screen is completely blank.
Tested CPU, GFX, RAM and PSU in another base unit and they work fine, yet put them all together and nothing.
1st I thought it was the mainboard so I sent the ASUS board back and ordered the KT6 Delta nice looking board. But still exactly the same problem.
Lights on case are lit all fans are turning ect yet still the system will not boot up i dont even get a flashing cursor top right of my screen.
There is no light with this mainboard for some reason.
All components work when fitted to another mainboard in a different case.
NB: one thing I have noticed is that there are two power sockets on this board,
1. The usual 20 pin socket (which I am connected to)
2. A 4 pin socket near to the CPU (whilst my PSU has a plug that will fit this sockect also, I am unsure as to connect instead of/as well as or leave unplugged.

Like I have stated before, it is the compatibility issue related towards your chip fsb and your memory fsb. I know that not everyone has money to go buy another stick of memory, I don't. But maybe you could exchange from the place you bought and say that it was a mistake? The cheapest route without getting the fsb chip to match the fsb of the memory stick is to get PC2700 memory. Have you tried going for this yet? I'm sure that your motherboard may not be shot, my board didn't get shot after trying to the two different fsb. You have to understand, motherboards are picky when it comes to running the hardware. If there is a conflict, it won't run right, I could run at a lower fsb and get it to work fine, but it wasn't at it's full potential, and I wasn't going to waste my time trying to find the fsb that would work correctly. So, I just let my friend have the stick back. This is why I'm asking you to try a lower speed stick of memory, because I have experienced this. But so far you haven't even seemed to notice my replies, could you take a quick overview of what I have said? Sorry if I come off as rude, just I am taking the time to write these replies and really am trying to help from my knowledge base. I have experienced this type of problem of what you are talking about personally.
Ok, so maybe I might not know it all, seeing that other people replying here have the same mb spec and chip fsb and memory like your trying to run, they might know more when it comes to that area for sure, just I didn't have luck trying to run a faster stick of memory compared to my chip, even though my board could run it, I couldn't get it to work, at all. I would just get a black screen, I thought I shot my GPU. Then I reset CMOS and the bios would flash, then when it would start pulling from harddrive, boom, black screen again. I had my friend tinker with my volt. to the right volts of the memory stick, still couldn't get nothing. This is why I am a little skeptical about you being able to run it at all in the long run. Hopefully you can find a way, maybe it is your manufacturer of your stick, but my conclusion is, if it isn't going to work with one, or two of same speed, try lowering it. Like I said, I tried it on this setup right now, and I didn't have to replace the chip or mobo, or gpu, so those should be fine.

System will not boot with Seagate 3Tb expansion drive plugged in.

I have a HP Pavilion HPE h8- 1214 Desktop , I recieved a Seagate 3TB expasion drive as a gift but when plugged in, the system will not boot. It turns on but thats it. It never gets to the boot sequence. I have it plugged into the top 3.0 usb slot and have tried all of the other slots as well with no sucess. But if I leave it unplugged the system boots right up. I can then plug it in and it works fine. I have plugged it into my wifes HP All- In- One and it boots fine and works. I have a WD 2TB drive that works fine as well on my system . I have searched Segates support for hours and all they say is to change the boot sequence. Have tried that, no go. What they dont get is no matter what I do if that drive is plugged in it never gets as far as booting and reading the boot sequence. Please help. Thank you!

Hi NcBunky,
Are you using Win 7 64 bit? Did you update the Texas Instruments (TI) USB 3.0 XHCI Host Controller?
I have an H8 1380t PC. Updated the TI USB 3.0 driver and had the same problem.
When booting the PC with the USB 3.0 external drive connected to the PC the PC would not boot. When booting the PC with only the mouse, keyboard, and a USB 2.0 external drive attached the PC would boot. Once booted you could attach the USB 3.0 drive and it worked fine.
Solution was to roll back (reinstall) the TI USB 3.0 XHCI Host Controller to the original factory installed driver.
System now boots with the external USB 3.0 drive attached.
Jaco
****I am not an HP employee****
Please give a" Kudos" if advice received is relevant or" Accept as Solution" if your problem has been solved.
+++++++++++++++++++++++++++++++++++++++++++++++++++++
H8 1380t CTO, Intel i7 3820
16 GB DDR3
Pegatron Motherboard- IPIWB-PB (Pittsburgh), Radeon HD 7570 1GB. Win 7 Home Premium upgraded to Windows 8.1 Pro.
Envy Phoenix 810-150se, Intel i7 4820k
16 GB DDR3
Pittsburgh2 Mainboard, NVIDIA GTX 645- 2GB GDDR5. Win 8.1 Pro.
HP 560z CTO AMD Phenom II X6 1090T
16 GB DDR3.
Radeon HD 6570
Win 7 Home Premium upgraded to Win 7 Pro.
HP ENVY 17t-j000 CTO Quad Edition Notebook. I7 4702mq
12 GB DDR3
Nvidia Graphics
Win 8 Pro
Errare humanum est.

Windows 8 and Canvio Desk 3TB: System will not boot when external hdd is connected

http://h30434.www3.hp.com/t5/Desktop-Operating-Systems-e-g/HP-PAVILION-A6109N-amp-windows-8-System-w...
Hi,
just recently upgraded to Win Pro on my HP PAVILION A6109N. I also bought a toshiba canvio desk 3TB. What I notice is that if I reboot my pc with the extermnal HDD connected, my system will not boot.
I have check my BIOS boot settings and the order of the boot.
I have tried disabling USB Legacy Support in the BIOS
I have reformatted the external HDD
but still my desktop will not boot if the external HDD is connected....If I disconnect the external HDD...the system will boot up ....
I am at a loss....*** scratching my head ***

Update: The only solution for me was to format the drive as ext3 and plug it into one of my Asus RT-N66U USB ports, as most routers don’t yet recognize 3TB drives as NTFS. It’s not much help to people who don’t have a router with this capability, and it also slows transfer rates to ~12MB/s.
Given the short length of the cable, your only other options are to have the 3TB Canvio sitting right next to you so you can unplug from a front USB port before each boot, or place it towards the rear of your desk and crawl under the desk to disconnect it from your PC prior to each boot.
It's a pity because Toshiba produce great internal HDD's, but my experience when it comes to external drives is they're simply junk. I wish I had read the reviews before purchasing.

I want to wipe iBook of it's content, but it will not boot up from DVD

Can someone tell me how I clear off the content of iBook and install the basic set of the applications? I have the original OS 9 disks but they will not boot up with these. I have gradually upgraded the OS so I don't have disks to match 10.4.11.
I want to give this away, as I bought new MacBook Pro recently and I have all of the files on the new computer, (and on another hard drive).
Thank you for any help from out there.

No problem; I usually answer good questions already solved. (It's for the search engine.) Here's how to wipe a corporate or government ATA hard drive.
Should you be concerned about spies, industrial and foreign, or even you own personal information, there is a standard method of erasing ATA disks that contain government classified information. Most ATA disks have it built in (and is a concern when purchasing computers for classified research). It's extreme, but sometimes necessary: information otherwise remains stored on 'bad' blocks, &c.
At one time, only the DOS program HDDerase activated the secure erase in ROM. For Mac users, the Linux program 'hdparm' (which has other uses) will do this from a Live Linux distribution on CD (unless you can boot a USB Flash Drive).'Darwin' might have it.
How to Nuke an ATA Hard Drive
http://ata.wiki.kernel.org/index.php/ATASecureErase
Note that, if you stop the process part way though, the disk may not be usable again (except to spies). Also, nothing is guaranteed.
If Darwin doesn't have it, or if it doesn't work, LiveCD distributions, such as Mint, Berry, & those of major distributions can be found here:
Linux Release Watch
http://distrowatch.com/

The system will not boot

Hello, I am trying to install windovws after the restart can not install Yosemite because can`t please format the hard disk.Please help because just yesterday bought macbooc

FYI...the top partition is too full. You need free space. You will need to remove the bottom partition then make the top partition larger. Make sure you have 10% or more free space. If you use Parallels or VMware you don't have to partition your drive. If you use the vm software you can run Windows wihtout having to reboot into bootcamp each time you want to use it.
See this link for help after you resize your top partition.
https://www.apple.com/support/bootcamp/
I forgot to ask...
If the system will not boot, how are you seeing Disk Utility. Are you booted from the Recovery Drive? If yes, then you will need to erase the internal drive and reinstall Yosemite on the internal. When you erase, make it one partition. You can add a second partition later that's smaller.
Note: you posted in the OS X 7 Lion instead of the Yosemite forum. In the future, asking on the correct forum gets the best answers.
Parallels http://www.parallels.com/
VMware Fusion http://www.vmware.com/products/fusion/

Operating reference system will not boot.

hi! bought the iphone 4s in Italy and it does not work. Operating reference system will not boot. Change of firmware and restore did not help. How can I change it while in Russia. Can I send in the mail store??

Hi NcBunky,
Are you using Win 7 64 bit? Did you update the Texas Instruments (TI) USB 3.0 XHCI Host Controller?
I have an H8 1380t PC. Updated the TI USB 3.0 driver and had the same problem.
When booting the PC with the USB 3.0 external drive connected to the PC the PC would not boot. When booting the PC with only the mouse, keyboard, and a USB 2.0 external drive attached the PC would boot. Once booted you could attach the USB 3.0 drive and it worked fine.
Solution was to roll back (reinstall) the TI USB 3.0 XHCI Host Controller to the original factory installed driver.
System now boots with the external USB 3.0 drive attached.
Jaco
****I am not an HP employee****
Please give a" Kudos" if advice received is relevant or" Accept as Solution" if your problem has been solved.
+++++++++++++++++++++++++++++++++++++++++++++++++++++
H8 1380t CTO, Intel i7 3820
16 GB DDR3
Pegatron Motherboard- IPIWB-PB (Pittsburgh), Radeon HD 7570 1GB. Win 7 Home Premium upgraded to Windows 8.1 Pro.
Envy Phoenix 810-150se, Intel i7 4820k
16 GB DDR3
Pittsburgh2 Mainboard, NVIDIA GTX 645- 2GB GDDR5. Win 8.1 Pro.
HP 560z CTO AMD Phenom II X6 1090T
16 GB DDR3.
Radeon HD 6570
Win 7 Home Premium upgraded to Win 7 Pro.
HP ENVY 17t-j000 CTO Quad Edition Notebook. I7 4702mq
12 GB DDR3
Nvidia Graphics
Win 8 Pro
Errare humanum est.

How do I get recover disc for vista when system will not boot???? For Pavilion pc a6157c

Pavilion pc a6157c How do I get recover disc for vista when system will not boot????

Read THIS HP Support Document concerning ordering recovery discs for your HP a6157c. Go to THIS HP webpage to order the "Vista Home Premium 32bit 73NAv3PrA1 + Supp 4 Recovery Kit" for your computer. If you are not looking to order the recovery discs or have some other issue with your computer, please provide detailed information concerning the problem.
Frank
Frank
{------------ Please click the "White Kudos" Thumbs Up to say THANKS for helping.
Please click the "Accept As Solution" on my post, if my assistance has solved your issue. ------------V
This is a user supported forum. I am a volunteer and I don't work for HP.
HP 15t-j100 (on loan from HP)
HP 13 Split x2 (on loan from HP)
HP Slate8 Pro (on loan from HP)
HP a1632x - Windows 7, 4GB RAM, AMD Radeon HD 6450
HP p6130y - Windows 7, 8GB RAM, AMD Radeon HD 6450
HP p6320y - Windows 7, 8GB RAM, NVIDIA GT 240
HP p7-1026 - Windows 7, 6GB RAM, AMD Radeon HD 6450
HP p6787c - Windows 7, 8GB RAM, NVIDIA GT 240

Laptops screen wont light and the system will not boot most of the time.

my hp lptop g62 started not booting up and the monitor would not light up sometimess even though it would power up. as time passed it had that problem more frequently. now it wont boot at all and the monitor wont light up at all . it will still power up but thats as far as it will go. ive tried a recovery disk but it will not boot the machine either nor will the monitor light up . im a novice so any help will be appreciated.
This question was solved.
View Solution.

Hi
This may be a disply issue try to connect a external monitor to your notebook and see if you get the display there.
You can connect to an external monitor via a VGA or HDMI connection. The usual process to transfer the video output to an external source is to hold down the fn key and press f4. Use the arrow keys to select 'Projector Only' and hit enter.
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02013758&cc=us&lc=en&dlc=en
and i also found a couple of links that may help you
http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&dlc=en&docname=c01884928
http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&dlc=en&docname=c01443371
Hope this helps.
***** Click the KUDOS Thumbs UP (Like) on the left to say 'Thanks'*****
****Make it easier for other people to find solutions, by marking my answer “Accept as Solution”&"Kudos"if it solves your problem.****
-VJ
Although I am an HP Employee, I am speaking for myself and not for HP.

ITunes is installed but it will not start

I just updated iTunes and the progam shows as being installed but iTunes will not start.

I have had this problem - started two days ago. (Win 7 Enterprise 64-bit OS.) I have not added anything new recently that could cause a conflict (upgrades, new software, etc). Suddenly it didn't work - will not open. In Windows Task Manager I can see that it starts and then stops without opening. I've plugged in my IPhone, IPad and IPod and nothing will connect. Some forum threads suggest removing/reinstalling QuickTime and some have found that to work. Didn't for me. It will open if "Run as Administrator" is used, but that - according to threads - suggests third-party add ons as a problem. Not the case with mine. I completely removed all of the ITunes software (Bonjour, Mobile Support, etc.) and reinstalled. Nothing changed. I am so frustrated with Apple on this - I found nothing in the support discussions to help. Quite frankly, I do not understand why Apple, with tech equipment that is so well designed and elegant, still puts out such a lousy piece of software that you are held hostage to use. I have hit a wall - I hope you get a response and help! I've run out of ideas!

PowerMac G4 Dual Optical - will not boot & no display

PowerMac G4 Dual Optical - Model Number 8570 EMC No 1914 : 1.25GHz DP/256M DDR@ 333/80G/Combo/MDM Operating system OS X 1st or 2nd release
This machine was used daily until February 2007. From then till the last week of September 2009 the machine was in storage and was not powered up
When tried for the first time in over 2 years, the machine powered up and the main switch on the front of the computer came on but no audible chime was heard. The machine will not boot & no display (apart from grey screen visible).
The 3.6 v lithium battery was replaced. PRAM & NVRAM has been reset via the keyboard commands : CommandOption+PR keys. After this, the chimes would work on power up but nothing is visible on screen. Also although the keyboard is functional evidenced by the success of the PRAM reset commands, the num & caps lock lights will not work nor will the CD drive "arrow" eject button. I have also removed the battery, reset the PMU on the logic board, and left the machine for over 30 minutes before powering up again:
Please advise if there is anything else I can try before I take it to a dealer for repair ?
Many thanks
Mike

Try a PMU reset.
DALE

System will not boot when Aironet 802.11a/b/g adapter installed

I have an HP 8000 Elite sff that will not boot after installing the adapter. I am running XP sp3. As soon as I remove the adapter, it boots fine.???

Which adapter ? Aironet 350 or CB21 ?
Do you have another similar adapter to put in the laptop to try ?
Is the problem new ? did it suddenly happen ?
Nicolas.
===
Please rate answers that you find useful

Reset CMOS, system will not boot

This is a long story but I will try to keep it short:
I just bought a new 875P Neo-FISR and a 3.0 GHz Prescott, which from reading the other posts could have been a mistake. I installed the CPU, memory, and the video card and pressed the power button and received a "CMOS Data Wrong" error. So I tried to correct the problem but when I saved and exited then the system would not boot back up. So, I reset the CMOS via the jumper and tried again. After MANY attempts I change just the month in the date setting. And what do you know...it would not boot back up. The D-Bracket LEDs were: 1-flashing red/green, 2-flashing red/green, 3-red, and 4-red
I must have read almost every post in this forum and tried many things such as:
disconnecting all componets except for video, ram, and cpu
the during boot to recover the BIOS
removing mobo from case, maybe a short
moving the memory to different slots
moving the PSU to a different computer...it works
disconnecting the PSU from the mobo and and removing the battery overnight. The first night I did not disconnecting the PSU from the mobo and I found that did nothing.
Tryed everything that I could think of and some stuff that others thought of but nothing worked. However the last item...removing the battery...did change things some. Now nothing happens, and I mean nothing...no lights, no fans, no buzzing...nothing.
Any ideas would be greatly appreciated. The only recourse I have left is to RMA the board.

I tried one stick in all of the slots with and without the sound card. That did not work either.
The voltage for my memory is 2.6 so that is what I tried. But if I can get it to boot up again I will try 2.7.
Tks.

Urgent: Power out - complete System will not boot

The power was shut off abruptly
root and usr are only filesystems mounted
Thus, can not init or boot...
shutdown gives this error:
showmount: sunfire: RPC: Rpcbind failure - RPC: Unable to receive
Do you want to continue? (y or n): showmount: sunfire: RPC: Rpcbind failure -
RPC: Unable to receive
Shutdown aborted.
any suggestions as to a solution??
would simply powering off then on really destroy things ??
Thanks

Please help. Have similar problem. After power out abruptly, cannot return to i6 state. System remains in single user mode. Tried running "reboot -n" which gave me a message to run "fsck -F ufs /dev/rdsk/c0t0d0s5". I did that, but still will not boor to multi user mode. This is the error msg I get:
"Shutdown started. Sat Mar 3 20:15:17 EST 2007
Changing to init state 6 - please wait
showmount: servername: RPC: Rpcbind failure - RPC: Unable to receive"
Any idears are very welcome

HP Pavilion DV7; System will not boot; Memory Test Failed using Advanced System Diagnostics

Not sure exactly how, but I managed to contracted several variants of the nasty Rovnix virus and now my system will not even boot into Safe Mode after trying to restore to several different restore points. Enabled bootlogging, but not sure how to retrieve the log.
Currently am able to get into HP Advanced Diagnostics and began Start-Up Test. Test failed on Memory Module:
Failure ID: Q0AE6C-5LS79T-MFH15G-406N03
Any next steps or directional assistance would be greatly appreciated. Thank you in advance!

Hello @GarrettBishop,
Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I have read your post on how your notebook computer has failed a memory test in the advanced system, and I would be happy to assist you in this matter!
Since the Failure ID has come up with Q0AE6C-5LS79T-MFH15G-406N03, I recommend contacting our technical support at 800-474-6836. If you live outside the US/Canada Region, please click the link below to get the support number for your region.
http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html
I hope this helps!
Regards
MechPilot
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

Diamond - 4870 Installed ...... but system will not boot - no display..

Similar Messages

Maybe you are looking for