Difference between 3G and Dual Mode?

When I go through cellular network options, I get 3 options as GSM, 3G and Dual Mode. What is the difference between the Dual Mode and 3G, and what exactly is this Dual Mode? When should I choose that over 3G?
Solved!
Go to Solution.

Dual mode means that the phone will connect to either 2G (GSM) or 3G connections. It will try for a 3G connection if it's strong enough, otherwise, it will go to a 2G connection.
The difference between 3G and dual mode, is in 3G mode, the phone will only try to connect to a 3G connection.
In most cases, dual would be better. If you are in an area will really strong and constitent 3G, then it's probably better to be on 3G.

Similar Messages

Specific differences between AP and bridge modes?

I've RTFM'd everywhere but cannot find anything definitive regarding the differences between AP+client versus bridge+bridge modes.
Presume you have a pair of AP1200's. First test case: One is in AP mode and the other is in WGB mode. Second test case: One is in root-bridge mode and the other is in non-root-bridge mode.
In both cases traffic will pass bidirectionally from one Ethernet port to the other. What, then, are the technical differences between these two situations? Do the "bridges" place less load on the AP1200's CPU? Does AP-based operation yield more diagnostic data? What are the advantages and disadvantages of each mode?
I can't find anything that digs into the details. Any help appreciated. Thanks!

Thanks for your response. A few comments, and then a question:
* Looks to the AP just like a standard client, so it interoperates with all APs
What does? A 1200 in WGB mode? If so, then yes it looks like a standard client to the AP but Cisco explicitly states it will only associate with other Cisco AP's. It is not compatible with "all APs".
If you mean a non-root-bridge looks like a standard client to an AP, that's true but the AP must be in "AP with wireless clients" mode which is not one of the test cases I was asking about.
* No configuration required
Of the WGB? Mine need configuration: SSID, encryption keys, etc. It's just like setting it up as an AP except for the mode you select.
Of a (non-)root-bridge? Mine have needed configuration in that mode, too. Same as above.
Not sure what you mean by "no configuration required".
# Disadvantages:
* Supports only a single wired client
Nope, in WGB mode pre-1200 units supported up to eight wired devices. 1200's and later support up to 250 clients. Cisco docs are clear on this.
In bridge mode I'm not aware of any wired client limits. The device is simply passing traffic between the two interfaces.
* WGB itself is not manageable
Not sure what you mean by "not managable".
Back to my question: What is the difference between AP+client mode vs. root-bridge+non-root-bridge mode? Does the AP+client mode make more decisions about traffic routing or prioritization, while bridge-based operation is less "intelligent"? Something else?
My tests show no discernable difference in throughput, even with multiple clients/nonroot bridges. When multiple users consume bandwidth simultaneously, it is shared among them just as you'd expect.
So... what ARE the differences, as far as the decisions IOS is making, between the different modes?
Thanks!

Difference between Routed and Transperant mode on firewall

Hi,
Can any one explain about Routed and transperant mode on Cisco ASA in a simple words..

To use an example from the University of Wisconsin-Madison, we have about 220 departments, centers, institutes, and other administrative units on our campus. Some are large and complicated, have their own IT staff, run their own delegated DNS, have multiple sites, and tend to run their own firewalls in routed mode. This will typically be the case for anyone who is using a lot of vlans to segregate traffic for security or performance reasons. Converse, some units are small, single-site, have only one subnet, and lack IT staff. The campus offers them virtual firewall contexts on shared central equipment, and runs those in transparent mode. In transparent mode the routers distinguish the two sides of the firewall using different vlan tags. In routed mode, each firewall interface is on its own distinct subnet as well as vlan, and the uplink outside interface needs a distinct transit subnet of its own, usually something between a v4 /29 - /30.
The choices are not mutual exclusive - I do it both ways on different parts of my network. Mostly of my traffic is in routed mode on my own gear, but I have one segregated sub-unit using transparent mode on the shared campus gear instead. Even on a home network you might be doing it both ways; e.g. if you have a broadband DLS or cable modem plus your own separate wifi router, the modem will typically run in transparent mode (bridging traffic), while the wifi+ethernet device will typically run in routed mode to provide NAT44 service. Cisco ASA gear lets you choose.
-- Jim Leinweber, WI State Lab of Hygiene

Difference between bridge and local mode with wlc 5508

Hello,
Now i have wlc5508 with few ap 11xx 12xx in local mode. All work correct. I will have to add few ap1552 in bridge mode ( i have to wait for wlc upgrade to change ap1552 to local mode). My question is that all ( local and bridge mode) will work correct together for my clients: rfid readers, laptop, computer in a,b,g,n mode ? What about roaming and other feature ?
thanks for help
Peter

If you plan on not doing MESH, then you set these 1552's in local mode and they will perform the same tasks as any other AP's in local mode. When you want to do MESH, then that is when bridge mode comes into play and you have to define your RAP's and MAP's.
Roaming, clients devices, doesn't matter if your using local or bridge. roaming depends on your device and coverage and rfid, also depends on triangulation with the coverage you have now.
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered"

RV042 - What's a practical difference between gateway and router mode

That´s my scenario, I have a RV042 as gateway on subnet 192.168.254.0,subnet 192.168.0.0 on the same LAN and 3 vpn tunnels connected GATEWAY TO GATEWAY on subnet 192.168.1.0,192.168.2.0 and 192.168.4.0. I setup 192.168.0.0 as Multiple Subnet on RV042 so now i can ping 192.168.0.0 from RV042 but i can´t do this from clients. What i want to know is What will happen if i change RV042 mode from gateway to router and What do i do to make clients (workstations) on subnet 192.168.254.0 reach clients in subnet 192.168.0.0 .
Thx
Everyone

Gateway mode = RV042 does NAPT (network address & port translation);
Router mode = RV042 does not do NAPT

Strange Difference between runtime and development mode.

Hello everyone,
I have created an add-on that adds three items to the menu which launch three different forms. When SBO is loaded and I run the code from the development environment (VB6) it works perfectly, i.e. click on one of the three new menu items and the appropriate form loads.
When I compile and register it as an add on SBO loads it correctly and it customizes the menu. However, when I click on any of the three new menu items it now gives an error message:
Run Time Error (91)
Object variable or With Block variable not set.
And then blows away the add on.
I tried trapping the error in the "Menu_Event" and got nothing. The error occurred as before with no evidence that it had been caught by my trap.
This same behavior occurs on both my development system and on the customer's production system! Both systems are 6.5 sp1 Ef 07.
Has anyone else had this problem? Any help appreciated.
Mel

Hi Mel,
I heard of a similar problem - just that the menu event did not get fired.
Do you use event filters?
Did you add the menu event to the filters collection?
Set oFilter = oFilters.Add(et_MENU_CLICK)
Though apparently this should have been mandatory, in case you use filters, from the beginning of 6.5, what I heard from another partner does not match to this information.
HTH,
Frank

Difference between automatic and non-automatic page attributes

Hi,
Can anyone tell me difference between automatic page attributes and non-automatic page attributes?
and also difference between stateful and stateless mode with examples?
Thanks
Narendra

Hi Mullapudi,
If you mark a page attribute as u2018automaticu2019 (auto in the system), the attribute automatically gets its values via the calling URL or
via the navigation process from other pages.
This kind of attribute only has to be declared for one page.
It is identified by its name equivalence.
If another page uses a parameter with the same name,
at runtime that parameter automatically
gets the same values as the attribute.
Non-automatic page attributes
If you flag a page attribute as non-automatic, the attribute gets its values from the class attribute.
The visibility of page attributes when parameters are transferred between BSP pages depends on whether the navigation is explicit or implicit.
Explicit navigation
For example, if navigation->goto_page(page.htm)
Implicit navigation
With implicit navigation, the page attributes are transferred automatically from OnInputProcessing to OnInitialization, both in stateful and stateless mode.
The auto page attributes are refilled by the request, both in stateful and stateless mode.
Reward if Useful...
Regards,
Anita. B

Difference between Reporting Services Sharepoint Mode and Reporting Services Add In for Sharepoint 2013

Hi, We are building company site with Sharepoint 2013 Enterprise Edition and were wondering what is the difference between Reporting Services Sharepoint Mode and Reporting Services Add In for Sharepoint 2013? What are the roles/purposes of each one? What
happens if only Reporting Services Sharepoint Mode installed or vise versa.
Thank you in advance

Reporting Services in SharePoint mode is a service for displaying, managing, and creating SSRS reports within SharePoint. The addin is a pre-req for SharePoint that is used to display reports and is required for Reporting Services in Native or SharePoint
mode, but does not by itself do anything.
Trevor Seward
Follow or contact me at...
&nbsp&nbsp
This post is my own opinion and does not necessarily reflect the opinion or view of Microsoft, its employees, or other MVPs.

Difference between trunc and mod

hi,
what is the difference between trunc and mod operator
can any one explain
thanks in advance

If you are going to ask for the difference between every pair of unrelated functions we could be here for some time. What is the difference between UPPER and CEIL? etc
TRUNC and MOD are both clearly documented in the SQL Reference.

Difference between passive and active data connection mode for FTP

Hi,
Does any body have the idea of passive and active data connection mode for the transport protocol FTP.
I have one server with FTP, I have to pick the data from this FTP to XI.
What is the difference between active and passive data connection? Does XI supports both the connections?
Thanks & Regards
Katta Mohan Reddy

Hi
According to SAP Note - 821267
Q: Does the File Adapter support active data connections when connecting to an FTP server?
A: Up to and including SP14, the File Adapter exclusively uses passive data connections. Starting with SP15, active connections will be available.
Difference between active and passive,
You can definitely refer to the site mentioned by Suraj
cheers
Sameer

Difference between Insert and Insert all

Hi,
I tried to understand what INSERT ALL syntax is doing, but I cannot find any difference between INSERT and INSERT ALL.
I replicated the test scenario using the data from the below mentioned URL:
http://psoug.org/reference/insert.html
I also did a google on finding up the difference between them, but could not find any...
Please advice if both are same as I have planned to use INSERT statement with a WHEN clause if INSERT ALL is same as INSERT.
Thanks!

Hello
The key difference is that INSERT ALL will allow you to insert into multiple different tables in a single statement whereas INSERT will only insert into 1 table. Each of the WHEN clauses allows a different table to be specified.
SQL> create table t1
2 (   id number
3 )
4 /
Table created.
Elapsed: 00:00:00.01
SQL> create table t2
2 (   id number
3 )
4 /
Table created.
Elapsed: 00:00:00.00
SQL> create table t3
2 (   id number
3 )
4 /
Table created.
SQL> INSERT
2 ALL
3      WHEN id < 10 THEN
4          INTO t1 VALUES(id)
5      WHEN MOD(id,2) = 0 THEN
6          INTO t2 VALUES(id)
7      WHEN MOD(id,2) != 0 THEN
8          INTO t3 VALUES(id)
9 SELECT
10      rownum id
11 FROM
12      dual
13 CONNECT BY
14      LEVEL <=20
15 /
29 rows created.
Elapsed: 00:00:00.01
SQL> select * from t1;
        ID
         1
         2
         3
         4
         5
         6
         7
         8
         9
9 rows selected.
Elapsed: 00:00:00.01
SQL> select * from t2;
        ID
         2
         4
         6
         8
        10
        12
        14
        16
        18
        20
10 rows selected.
Elapsed: 00:00:00.00
SQL> select * from t3
2 /
        ID
         1
         3
         5
         7
         9
        11
        13
        15
        17
        19
10 rows selected.
Elapsed: 00:00:00.01So you can see that in a single statement, I've inserted all rows with an ID <10 into t1, all even numbered rows into t2 and all odd numbered rows into t3. This was also done with a single pass of the source table - in this case dual.
David

What is the difference between LH and LX modules?

I would like to know the difference between LX and LH SFP modules. Long Haul ( LH ) denotes longer distances while Long Wavelength ( LX ) denotes less energy which is obviously shorter distance. Why does Cisco use both LX and LH for certain SFP modules?
Do they denote the capability of the module to work both for MM ( which will be Long wavelength ) and SM ( Long Haul ) fiber? Do correct me if i am wrong.
What does it infer if a modules says like "Cisco 1000BASE-LX/LH SFP" ?

What does it infer if a modules says like "Cisco 1000BASE-LX/LH SFP
Generally a module is either made for single mode (More distance) / multimode (short distance). But this module can be used for both Single mode and Multimode.
If used with SM fiber it can go upto 10Km
It used with MM it can go upto 550meters (depend on what kind os MM fiber you have) You need a mode conditioning patch chord too with legacy MM i think OM1 and 2.
Long Haul ( LH ) denotes longer distances while Long Wavelength ( LX ) denotes less energy which is obviously shorter distance. Why does Cisco use both LX and LH for certain SFP modules
Read this link and dont worry about LX/LH (You will ge tthe distance mentiond above depending on the type of fibe ryou are using)
http://en.wikipedia.org/wiki/Gigabit_Ethernet
Before it was standardized 1000BASE-LX10 was essentially already in widespread use by many vendors as a proprietary extension called either 1000BASE-LX/LH or 1000BASE-LH

What is the difference between exists and in

hi all
if i have these queries
1- select ename from emp where ename in ( select ename from emp where empno=10)
and
2- select ename from emp where exists ( select ename from emp where empno=10)
what is the difference between exists and in is that only when i use in i have to bring the field name or what.... i mean in a complex SQL queries is it will give the same answer
Thanks

You get two entirely different result sets that may be the same. Haah! What do I mean by that.
SQL> select table_name from user_tables;
TABLE_NAME
BAR
FOO
2 rows selected.
SQL> select table_name from user_tables where table_name in (select table_name from user_tables where table_name = 'FOO');
TABLE_NAME
FOO
1 row selected.
SQL> select table_name from user_tables where exists(select table_name from user_tables where table_name = 'FOO');
TABLE_NAME
BAR
FOO
2 rows selected.So, why is this? the WHERE EXISTS means 'if the next is true', much like where 1=1 being always true and 1=2 being always false. In this case, where exists could be TRUE or FALSE, depending on the subquery.
WHERE EXISTS can be useful for something like testing if we have data, without actually having to return columns.
So, if you want to see if an employee exists you might say
SELECT 1 FROM DUAL WHERE EXISTS( select * from emp where empid = 10);
If there is a row in emp for empid=10, then you get back 1 from dual;
This is what I call an 'optimistic' lookup because the WHERE EXISTS ends as soon as there is a hit. It does not care how many - only that at least one exists. It is optimistic because it will continue processing the table lookup until either it hits or reaches the end of the table - for a non-indexed query.

Difference between continue and Exit ........?

Difference between continue and Exit ........

See a small example CONTINUE below with some notes:-
When Nothing to Do, CONTINUE: - In Oracle Database 11g PL/SQL has a new construct called CONTINUE, which is used in a loop. The statement moves the logic to the end of the loop and then to the beginning of the loop.
Eg:
begin
        for ctr in 1..100 loop
                continue when mod(ctr,10) != 0;
                dbms_output.put_line ('ctr='||ctr);
                  Continue Skip the executions of statements after this clause Like for numbers, those are not a multiple of 10. And comes to end loop then to start of loop
        end loop;
end;
Here is the output:
ctr=10
ctr=20
ctr=30
... and so on ...EXIT take you out of LOOP from current iteration and that will be last iteration.
Thanks!

What is the difference between TO_CHAR and TO_DATE()?

Hi everybody,
i am facing a problem in my system.It is quite urgent, can you explain me "What is the difference between TO_CHAR and TO_DATE()?".
According to user's requirement, they need to generate a code with format "YYMRRR".
YY = year of current year
M = month of current month (IF M >=10 'A' ,M >=11 'B' , M >=10 'C')
RRR = sequence number
Example: we have table USER(USER_ID , USER_NAME , USER_CODE)
EX: SYSDATE = "05-29-2012" MM-DD-YYYY
IF 10
ROW USER_ID , USER_NAME , USER_CODE
1- UID01 , AAAAA , 125001
2- UID02 , AAAAA , 125002
10- UID010 , AAAAA , 12A010
This is the original Script code. But This script runs very well at my Local. Right format. But it just happens wrong format on production.
12A010 (Right) => 11C010 (Wrong).
SELECT TO_CHAR(SYSDATE, 'YY') || DECODE( TO_CHAR(SYSDATE, 'MM'),'01','1', '02','2', '03','3', '04','4', '05','5', '06','6', '07','7', '08','8','09','9', '10','A', '11','B', '12','C') ||     NVL(SUBSTR(MAX(USER_CODE), 4, 3), '000') USER_CODE FROM TVC_VSL_SCH
     WHERE TO_CHAR(SYSDATE,'YY') = SUBSTR(USER_CODE,0,2)
     AND TO_CHAR(SYSDATE,'MM') = DECODE(SUBSTR(USER_CODE,3,1),'1','01',
          '2','02', '3','03', '4','04', '5','05',
          '6','06', '7','07', '8','08', '9','09',
          'A','10', 'B','11', 'C','12')
I want to know "What is the difference between TO_CHAR and TO_DATE()?".

try to use following select
with t as
(select TO_CHAR(SYSDATE, 'YY') ||
         DECODE(TO_CHAR(SYSDATE, 'MM'),
                '01', '1',
                '02', '2',
                '03', '3',
                '04', '4',
                '05', '5',
                '06', '6',
                '07', '7',
                '08', '8',
                '09', '9',
                '10', 'A',
                '11', 'B',
                '12', 'C') as code
    from dual)
SELECT t.code || NVL(SUBSTR(MAX(USER_CODE), 4, 3), '000') USER_CODE
FROM TVC_VSL_SCH
WHERE SUBSTR(USER_CODE, 1, 3) = t.codeand yes you need check time on your prodaction server
good luck
Edited by: Galbarad on May 29, 2012 3:56 AM

Difference between 3G and Dual Mode?

Similar Messages

Maybe you are looking for