Difference between PI/XI interface and ABAP interface

Hello Experts,
We are in the process of identifying interfaces for our current client. I am looking for some documentation or any specific information that will help me to differentiate between SAP PI interface and ABAP Interface. Basically I want to know what are the advantages of PI interface over ABAP interface. What is better? and why?
Any information would be of great help. Thanks.

PI (versus point to point ABAP) advantages are:
1)     Centralized control over data security
2)     More effective (centralized) interface failure monitoring and resolution
3)     Elimination of redundant development and maintenance costs

Similar Messages

  • The difference between IEEE802.1Q Native VLAN sub-interface and Physical interface?

    Hello
    I think the following topologies are supported for Cisco Routers
    And the Physical interface also can be using as Native VLAN interface right? 
    Topology 1.
     R1 Gi0.1 ------ IEEE802.1Q Tunneling  L2SW ------ Gi0 R2
    R1 - configuration
    interface GigabitEthernet0.1
     encapsulation dot1Q 1 native
     ip address 10.0.0.1 255.255.255.0
    Topology 2.
    R1 Gi0 ------ IEEE802.1Q Tunneling L2SW ------ Gi0 R2
    interface GigabitEthernet0
    ip address 10.0.0.1 255.255.255.0
     And is it ok to use the physical interface and sub-interface with dynamic routing such as EIGRP or OSPF etc?
    R1 Gi 0 ---- Point to Multipoint EIGRP or OSPF ---- Gi0 R2 / R3 
          Gi 0.20--- Point to Point EIGRP or OSPF --- Gi0.10 R4  (same VLAN-ID) 
    R1 - configuration
    interface GigabitEthernet0
     ip address 10.0.0.1 255.255.255.0
    interface GigabitEthernet8.20
     encapsulation dot1Q 20
     ip address 20.0.0.1 255.255.255.0
    Any information is very appreciated. but if there is any CCO document please let me know.
    Thank you very much and regards,
    Masanobu Hiyoshi

    Hello,
    The diagram is helpful.
    If I am getting you correctly, you have three routers interconnected by a switch, and you want them to operate in a hub-and-spoke fashion even though the switch is capable of allowing direct communication between any of these routers.
    Your first scenario is concerned with all three routers being in the same VLAN, and by using neighbor commands, you force these routers to establish targeted EIGRP adjacencies R1-R2 and R1-R3, with R1 being the hub.
    Your second scenario is concerned with creating one VLAN per spoke, having subinterfaces for each spoke VLAN created on R1 as the router, and putting each spoke just in its own VLAN.
    Your scenarios are not really concerned with the concept of native VLAN or the way it is configured, to be honest. Whether you use a native VLAN in either of your scenarios, or whether you configure the native VLAN on a subinterface or on the physical interface makes no difference. There is simply no difference to using or not using a native VLAN in any of your scenarios, and there is no difference to the native VLAN configuration being placed on a physical interface or a subinterface. It's as plain as that. Both your scenarios will work.
    My personal opinion, though, is that forcing routers on a broadcast multi-access segment such as Ethernet to operate in a hub-and-spoke fashion is somewhat artificial. Why would you want to do this? Both scenarios have drawbacks: in the first scenario, you need to add a neighbor statement for each spoke to the hub, limiting the scalability. In the second scenario, you waste VLANs and IP subnets if there are many spokes. The primary question is, though: why would you want an Ethernet segment to operate as a hub-and-spoke network? Sure, these things are done but they are motivated by specific needs so I would like to know if you have any.
    Even if you needed your network to operate in a hub-and-spoke mode, there are more efficient means of achieving that: Cisco switches support so-called protected ports that are prevented from talking to each other. By configuring the switch ports to spokes as protected, you will prevent the spokes from seeing each other. You would not need, then, to configure static neighbors in EIGRP, or to waste VLANs for individual spokes. What you would need to do would be deactivating the split horizon on R1's interface, and using the ip next-hop-self eigrp command on R1 to tweak the next hop information to point to R1 so that the spokes do not attempt to route packets to each other directly but rather route them over R1.
    I do not believe I have seen any special CCO documents regarding the use of physical interfaces or subinterfaces for native VLAN or for your scenarios.
    Best regards,
    Peter

  • Difference between abstract interface and normal interface

    Hello Friends,
    What is the Difference between abstract interface and normal interface?....

    What is the Difference between abstract interface and
    normal interface?....The difference is that you didn't follow convention in the first case. All interfaces are implicitly abstract so you don't have to declare them as such.

  • How is the interface between the Java Stack and ABAP stack is achieved?

    How is the interface between the Java Stack and ABAP stack is achieved?..Please send me the answer to [email protected]

    Hi,
    By interface, I assume you mean the connection between the ABAP and the Java stacks in a double stack system.
    The connection from Java to ABAP is through JCo connections defined in the WebDynpro section of the J2EE start page. So Java to ABAP requests are processed through JCo.
    The connection from ABAP to Java is through RFC connections defined in TA SM59. The ABAP to Java requests are processed through RFC.
    Refer https://dsd.esco-salt.com/StartPage/documents/integration/3.html for detailed explanation.
    The UME can be maintained in either ABAP or in JAVA depending on the persistence.
    Refer: http://help.sap.com/saphelp_nw70/helpdata/en/5b/5d2706ebc04e4d98036f2e1dcfd47d/frameset.htm
    Check UME data source configuration.
    Some quick FAQs can be found at:
    https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/ad47eb90-0201-0010-7cb2-ddfa5ed879ec
    Hope this helps.
    Best Regards,
    Srividya.R

  • Difference between web dynpro java and web dynpro abap

    Hi this is watson maureen,
                 I wnat to know what is  the difference between web dynpro java and web dynpro abap?
    thank
    maureen

    Hi watson,
    Go through these links, you will get the difference between web dynpro java and web dynpro abap
    https://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/e0e4940c-035c-2b10-0b9d-eb8f99674f4e
    Web Dynpro: ABAP or Java?
    Regards
    Sreedhar.

  • Could I configure local switching between sub-interface and global interface on ASR9k?

    Could I configure local switching between sub-interface and global interface on ASR9k?

    For 2 interfaces it is probably best to use an xconnect. It is faster and saves system resources (eg mac learning doesnt apply to xconnect).
    Config example:
    l2vpn
     xconnect group link
      p2p link
       interface Bundle-Ether100.4321
       interface Bundle-Ether500.4321
    EFP config:
    interface Bundle-Ether100.4321 l2transport
     encapsulation dot1q 4000
     rewrite ingress tag pop 1 symmetric
    interface Bundle-Ether500.4321 l2transport
     encapsulation dot1q 2000
     rewrite ingress tag pop 1 symmetric
    This example shows that you can link 2 EFP's with different vlan's together if you'd pop the tags.
    If the EFP's are of the same vlan, then popping the tag can be done but not a must. In general it is recommended to always pop vlan tags so there is a standard EFP design, but not for any technical reasons.
    When you use a bridge domain and using a BVI, you MUST pop the tags as the BVI has no notion of a vlan tag and wants to see "plain ethernet".
    regards
    xander

  • What is the difference between SAP HR module and SAP-ABAP-HR?

    what is the difference between SAP HR module and SAP-ABAP-HR?
    Thanks in advance..:)

    Hi,
    SAP-HR is software component like SAP-BASIS is a component.
    Its part of the CORE.
    As far as I know there is nothing like SAP-ABAP-HR.
    But ABAP offers some special syntax for HR though.
    Like INFOTYPES, PROVIDE ENDPROVDIE etc.
    Regards,
    Sesh

  • From ABAP view, what is the difference between version 4.7 and ECC 6.0 ?

    Hi,
    I am a ABAP developer. I want to know the difference between version 4.7 and ECC 6.0 from a programmer
    perspective.
    I also want to know  what is obsoleted and what is enhanced.
    Thanks.
    Best Regards,
    Chris Gu

    I'm not sure if any of this is in your 4.7 version, but I know it wasn't available in our 4.6C before we upgraded and we have found the following extremely helpful in ECC 6.0:
    1.  The new ABAP Debugger - Search SDN and you'll probably find a bunch of info on these enhancements
    2.  The Enhancement Framework - this is a great new framework allowing enhancements to standard SAP programs without having to use "core Mods".  Had we known about it prior to our upgrade, we could have probably eliminated 75% or so of our custom Z Programs which are copies of standard SAP code  and 100% of our core mods (of which we only have a handful)
    3. Code Inspector and more importantly the ability to turn it on to automatically run when releasing a transport.
    4. The ABAP workbench has changed a bit with a new editor including some minimal code completion.
    5.  Automatic generation of services from any remote enabled function module.
    These are just a few of the things that I've found helpful in an upgraded environment.

  • What is the difference between Component,Server,Tool and Software?

    HI,
    What is the difference between Component,Server,Tool and Software?
    SHABEER

    Hi
    Every individual part that constitutes in making an SAP System is called a COMPONENT.e.g DB instance, Java CI, ABAP CI etc
    SERVER is the actual composition of different components of SAP.e.g. a database alongwith can instance would constitue an application server.
    TOOLS are the products from different organisations (SAP or Non SAP) that can be used for different functionalities like keeping a check on jobs, monitoring of the system , e.g Tivoli
    SOFTWARES are a kind of tool that help you to bring up results from the system in a user acceptable format. These are utilities that act as interfaces between the user and the system.
    regards
    Chen

  • What is the differenec between 'sap list viewer' and 'abap list viewer'

    hi
    what is the differenec between 'sap list viewer' and 'abap list viewer'

    Hi,
    There is no difference between them.SAP List Viewer (ALV) is the new name of the ABAP List Viewer (ALV).
    The SAP List Viewer unifies and simplifies the use of lists in the R/3 System. A uniform user interface and list format is available for all lists. This prevents redundant functions.
    The SAP List Viewer can be used to view both single-level lists and multilevel sequential lists.
    Single-level lists contain any number of lines that have no hierarchical relationship to each other.
    Multilevel sequential lists consist of any number of lines that have two hierarchical levels. Multilevel lists have header rows and item rows; the item rows are subordinate to the header rows. For each header row there can be any number of subordinate item rows.
    You can view subtotals and totals rows in both single-level lists and multilevel sequential lists
    From End User Point it is SAP LIST viewer , From Developer Point of View it is ALV .
    Check the Below Link
    http://help.sap.com/saphelp_nw04/helpdata/en/66/bc7aab43c211d182b30000e829fbfe/frameset.htm
    Regards,
    Satish

  • What is the difference between Open hub destination and Info spokes

    what is the difference between Open hub destination and Info spokes?
    Please seacrh the forum before posting a thread
    Edited by: Pravender on Aug 16, 2010 11:17 AM

    Hi,
    When a user initiates open hub extraction by creating an InfoSpoke, behind-the-scenes activity involves OO ABAP which is calling classes to determine each of the different components involved in making the open hub extraction possible.  In particular, this enhancement will focus on 2 standard classes: one used to determine file destination name and path and the other to control the user interface of the InfoSpoke which will ultimately allow the user to enter his/her own filename and path.
    The open hub service enables us to distribute data from an SAP BW system into external data marts, analytical applications, and other applications. With this, we can ensure controlled distribution using several systems.
    The central object for the export of data is the InfoSpoke. Using this, we can define the object from which the data comes and into which target it is transferred.
    Regards,

  • Difference between ECC 6.0 and earlier versions

    Hi,
    one of the difference between ECC 6.0 and earlier versions is that instead 'WS_UPLOAD'  and 'WS_DOWNLOAD' in ECC we should use 'GUI_UPLOAD' and 'GUI_DOWNLOAD'  respectively.
    (of course SPDD and SPRO tcodes is known by everone i suppose)
    Similarly can u all put down some differences here, atleast one entry by each, I think we can make a good docu. I have searched the net for the differences but could not get much, so by each of us contributing one each, it would become good docu..for all of us.
    Thanx in advance

    Unicode Errors Encountered and their Solutions
    E1. In u201CTEXT MODEu201D the u201CENCODINGu201D addition must be specified.
         Error:
         OPEN DATASET FILE FOR OUTPUT IN TEXT MODE.
         Solution:
         OPEN DATASET FILE FOR OUTPUT IN LEGACY TEXT MODE.
    E2. In Unicode, DESCRIBE DISTANCE can only be used with the IN BYTE MODE  or  IN
          CHARACTER MODE  addition.
         Error:
         DESCRIBE DISTANCE  BETWEEN T_KOMK AND T_KOMK-HIEBO01 INTO BPOS.
         Solution:
    DESCRIBE DISTANCE  BETWEEN T_KOMK AND T_KOMK-HIENR01 INTO BPOS
    IN CHARACTER MODE.
    E3. u201CUSR02-UFLAGu201D must be a byte-type field (Typ X or XSTRING )
         Error:
         IF USR02-UFLAG O YULOCK.
         Solution:  Since the data type of USR02-UFLAG is type INT and is compared with data type
                    X u2013 Hence the error. So we  define a new variable ZULOCK and assign the
                    value of USR02-UFLAG to ZULOCK.
                  New variable             
                  DATA: ZULOCK(1) TYPE X.   "APBRP00
                  Assign value               
                                ZULOCK = USR02-UFLAG.
            Compare -
                   IF ZULOCK = YULOCK.   u201Creplace IF USR02-UFLAG O YULOCK.
    E4.  HT cannot be converted to a Character type field
    Error :
    WRITE ht TO t_data+10(2).
    Solution : Since the data type of ht is a type u2018Xu2019 and the data is been transfer to
             t_data which has a data type u2018Cu2019. value of one data type cannot be copy to
             another data type where one of them is type string .Hence the error occur,
             so the data type of ht is been change to Type u2018Cu2019
         OR
               A Tab ( value 09 ) is introduced as part of the row. The value 09 is not converted in Unicode environment. Instead we need to use class
         Error:
              DATA: BEGIN OF ht,
                   x(1) TYPE x VALUE '09',
              END OF ht.
         Solution:
                  Define Class after the Tables definition.
                       CLASS cl_abap_char_utilities DEFINITION LOAD.
                  Data Defination :  Comment internal table HT and define a variable HT type C.
           *   Insert + APRIA00 05/02/2007 Unicode project
           *   DATA: BEGIN OF ht,
         *         x(1) TYPE x VALUE '09'
           *   END OF ht.
         *   Insert - APRIA00 05/02/2007 Unicode project
           DATA HT type C.
           Before using HT assign Horizontal tab.
                     Ht = CL_ABAP_CHAR_UTILITIES=>HORIZONTAL_TAB.  
    E5.  In Unicode programs the u201C#u201D cannot appear in names, as it is does here in the name    u201C#LINESu201D
         Error :
         #LINES                 TYPE I,
         Solution : Since the # is used in the start of name, it is not allowed. We need to
                  remove it. 
         Solution for the above
         V_LINES                 TYPE I,
    E6. In u201CTEXT MODEu201D the u201CENCODINGu201D addition must be specified as well as the addition was required FOR OUTPUT,FOR INPUT, FOR APPENDING OR FOR UPDATE was expected.
         Error:
         OPEN DATASET PATH_NAME IN TEXT MODE.
         Solution:
         Download =     OPEN DATASET PATH_NAME FOR OUTPUT IN LEGACY TEXT MODE.
         Upload        =  OPEN DATASET AUSZUG-FILE IN TEXT MODE FOR INPUT ENCODING DEFAULT.
    E7. u201CTABu201D must be a character-type data object( data type C,N, D, T or String). Field string)    
         Error:
                data: begin of tab,                   "Excel Parameter Split at TAB
            t type x value '09',          "Tabulator
           end of tab.
                concatenate 'Material' 'Package Status'
                    into z_download-line separated by tab.
                ( In the above command  the two field are to be separated with a horizontal Tab. The earlier      way of assigning the tab value u201809u2019 will not work in Unicode environment.
         Solution:
         Define a  class just after the Table defination.
              CLASS cl_abap_char_utilities DEFINITION LOAD.
                Define  variable Tab as shown below :
              Data : TAB           TYPE C.
         Before the concatenate statement assign the value of Tab using pre-defined attributes.
              TAB = CL_ABAP_CHAR_UTILITIES=>HORIZONTAL_TAB.
    E8. Upload/Ws_Upload and Download/Ws_Download are obsolete, since they are not Unicode-
          enabled; use the class cl_gui_frontend_services     
         Error-1:  Function WS_DOWNLOAD is obsolete in Unicode environment.
                call function 'WS_DOWNLOAD'
                     exporting
                          filename = zfilename
                     tables
                          data_tab = z_download.
         Solutions-1: Instead of WS_DOWNLOAD use  GUI_DOWNLOAD.
    CALL FUNCTION 'GUI_DOWNLOAD'
      EXPORTING
    *   BIN_FILESIZE                  =
        FILENAME                      = zfilename
      TABLES
        DATA_TAB                      = z_download.
    E9.  The "/" character is reserved for identification of namespaces. It must be entered twice.
            The name  of a namespace must be at least 3 characters long.
         Error :      
                     U/N(3)        TYPE C,  "U/N    --> ERSETZT DURCH SPACE
         Solution :
         * Special character can not be used to define a data variable
         *      U/N(3)        TYPE C,  "U/N    --> ERSETZT DURCH SPACE
                  U_N(3)        TYPE C,  "U/N    --> ERSETZT DURCH SPACE
         * Insert - APSUS02 07/02/2007 Unicode Project
    E10.  "LP_TAB" and "CS_TAB" are not mutually convertible. In Unicode programs,
             "LP_TAB" must have the same structure layout as "CS_TAB", independent of the length
             of a Unicode character.
         Error : This error is encountered when data from one internal table is copied to another
                             internal table which different structure. In this case its LP_TAB & CS_TAB.
                     LP_TAB[] = CS_TAB[].
         Solution :
              * Replace + APSUS02 07/02/2007  Unicode Project
    *   LP_TAB[] = CS_TAB[].
                  move-corresponding CS_TAB to LP_TAB.
              * Replace + APSUS02 07/02/2007  Unicode Project
    E11.  Could not specify the access range automatically. This means that you need a RANGE
              addition.          
         Error :  Range need to be specified as an addition to the command.
                DO 4 TIMES VARYING HELP_CHAR FROM ABCD(1) NEXT ABCD+1(1).
               Solution : 
                DO 4 TIMES VARYING HELP_CHAR FROM ABCD(1) NEXT ABCD+1(1)
              * Insert + APSUS02 07/02/2007  Unicode Project.
                                                          RANGE ABCD+0(4).
    * Insert - APSUS02 07/02/2007  Unicode Project.
    E12 .  Processing Terminated Error code: Error in opening /
                                              Path not found when downloading to Unix directory.
         Error : PARAMETER: outfile(92) DEFAULT
                  '/CP/interface/NPP/data/MX/cbslaprcpts'
                        LOWER CASE,
                   kmxmstrd AS CHECKBOX.
                This error is encountered when the path is missing. The above path is related to CCP.
         Solution:  For testing purpose comment the original path and replace it with
                                     /CP/interface/CCD/Unicode_test/ 
    E13.    Upload/Ws_Upload and Download/Ws_Download are obsolete, since they are not                                                                       Unicode- enabled; use the class cl_gui_frontend_services
         Error: Function WS_UPLOAD is obsolete in Unicode environment. (During UCCHECK)
                   Call function 'WS_UPLOAD'
           Exporting
                Filename                = zfilename
                Filetype                = u2018DATu2019
           Tables
                data_tab                = z_upload
           Exceptions
                Conversion_error        = 1
                file_open_error         = 2
                file_read_error         = 3
                invalid_table_width     = 4
                invalid_type            = 5
                no_batch                = 6
                unknown_error           = 7
                gui_refuse_filetransfer = 8
                others                  = 9.
         Solution: Instead of WS_UPLOAD use TEXT_CONVERT_XLS_TO_SAP. Do not use temporary file put the file name as it is.
    1) First define a type pool and a variable of type truxs_t_text_data.
    TYPE-POOLS: truxs.
    DATA: it_raw TYPE truxs_t_text_data.
         2) Use this it_raw in the function module in parameter i_tab_raw_data. Put file name and the internal table in the function module.
    CALL FUNCTION 'TEXT_CONVERT_XLS_TO_SAP'
        EXPORTING
    *     I_FIELD_SEPERATOR        =
    *      i_line_header            =  ' '
          i_tab_raw_data           =  it_raw       " WORK TABLE
          i_filename               =  zfilename
        TABLES
          i_tab_converted_data     = z_upload[]    "ACTUAL DATA
       EXCEPTIONS
          conversion_failed        = 1
          OTHERS                   = 2.
         Comment u201Ci_line headeru201D. It takes the first/ header line of the file which is to be uploaded.
    Put  square brackets after internal table as shown above.
    E14.    CURSORHOLD may not be converted into a number.
         Error:  GET CURSOR LINE CURSORHOLD VALUE CURSOR_HOLD.
         Solution: In the declaration part of CURSORHOLD, one field is of u2018Pu2019 type and one field is of u2018Iu2019 type, which is not allowed in Unicode environment.So change the the type of it to NUMC.  

  • Difference between a Journal header and a journal line

    Hi,
    Can anyone please explain the difference between a Journal header and a journal line ? Can we have different journal headers for the same journal import process?
    Thanks and regards,

    Not sure if I know what you mean, but...
    You can organise your journals by using journal headers. A batch can contain many Headers. Like this:
    Batch No 1
    - Journal Header 1
       - Line 1       Deb: 200$
       - Line 2                      Cre: 100$
       - Line 3                      Cre: 100$
    - Journal Header 2
       - Line 1       Deb: 100$
       - Line 2                      Cre: 100$When you run Journal Import, you run for a specific source. So Yes you can have different journal headers for the same import process (if you mean import from GL Interface).
    Does this clearify?
    Botzy

  • Differences between CTI OS Server and CTI Server ?

    Hello community,
    I've been working with CTI Desktop for a while but I'm not clear about the differences between CTI OS Server and CTI Server?
    If you go to http://docwiki.cisco.com/wiki/Unified_CCE_Software_Compatibility_Matrix_for_8.5(x) and read note 10, they make diffrences between both products.
    Thanks in advance,
    Alejandro

    CTI Server was the original CTI interface into ICM.  It uses a network communication protocol, GED-188 I believe, for communication between the client and server.  This is relatively difficult to program against.  CTIOS and it's related SDKs were developed to provide an easier method of developing desktops and integrating desktop applications.  CTI Server communicates with ICM, CTIOS Server communicates with CTI Server, and desktop applications using the various SDKs communicate with CTIOS Server.  Cisco may be looking to get away from CTIOS Server in the future because of their decision to integrate Finesse with CTI Server rather than CTIOS Server.  Hope that helps.

  • Difference between XI 3.0 and XI 7.0

    What is the Difference between XI 3.0 and XI 7.0?
    ( functionality & architecture wise)

    Hi,
    There is no new features added in PI7.0, if u have working on XI 3.0, PI7.0 Older versions the features same..
    But PI7.1 there is new changes u can find below.....
    Integarte SAP & Non-SAP Legacy system
    PI 7.1 is based on open, web service enabled standards and
    Integrate all SAP and non-SAP, A2A, B2B, BPM, service enabling and BAM
    Highlight of enhancement in PI7.1
    1) Enterprise Service repository (ESR) contains the design Registry
    2) Includes significant high-volume message processing is supported by message processed in a single
    Service call
    3) Also importantly support for asynchronous messaging based Reliable Messaging (WS-RM) for both
    Brokered communication between two systems will be supported in this release.
    4) Provide Service Registry benefits based on UDDI 3.0
    Enterprise Service Repository
    In PI7.1 ES Repository is at the heart of Enterprise SOA
    ES Repository is really the master data repository of service objects for Enterprise SOA
    It contains the definition & process of services
    In ES Repository has two parts, one is the ES Repository and the other being the Services Registry
    ES Repository (ESR) is really the master data repository of service objects for Enterprise SOA
    Besides service definition the ES Repository also provides you with a central point for finding and
    Managing service metadata from different sources, including application deployments - this is
    Where the Services Registry comes in. The Services Registry is the UDDI part of the ESR which
    Enables service consumers to find services
    The SAP XI Integration Repository used by process integration has become the basis of the central Enterprise Service Repository: powering Enterprise SOA and Service Enablement.
    Objects in the ES Repository include:
    Global Data Types (CCTS based)
    Process Component Models
    Executable Integration Processes (BPEL)
    Integration Scenarios
    Service Interfaces (Enterprise Services)
    Interface Mappings
    Enterprise Services built in the ES Repository
    Enterprise Services includes:
    Are built using a consistent enterprise model based on: GDTs, Process Components, and Business Objects.
    Are based on open standards.
    Are mapped to the Service Interface object in the ES Repository.
    Global Data Types - Building blocks for Service Interfaces
    Defined in the ES Repository
    Defined company-wide based on open standards (ISO 15000-5, UN/CEFACT CCTS)
    Reusable semantic building blocks for service interfaces and message types
    Process Component Models
    Drill down from high-level models to service interfaces and operations
    Process component architecture models enable SOA governance
    Process components expose on enterprise services, which are based on service operations
    Web Services Reliable Messaging (WS-RM)
    Asynchronous messaging (EO, EOIO) based on open WS standard
    Support Business Activity Monitoring (BAM)
    Embedded Event Infrastructure: Collecting, pre-filtering and publication of events across SAP and non-SAP systems.
    Event handling: cast the local event to an event proxy to send out event messages to event Consumers.
    Transaction SWF_BAM for event filtering via filter rules and event handling.
    Enhancement for Mapping
    Re-usable user defined functions.
    Look-up function reads multiple fields.
    Synchronous DB RFC lookups: Use graphical function to model look-ups.
    Specify mapping parameters at configuration time.
    Principle Propagation based on SAML
    This feature uses the WS-RM protocol.
    The implementation of this feature is based on the open standard SAML and can
    be used with backend systems that support the SAML technology.
    Forward user context from sender to receiver.
    Authorization check in receiving system based on original user.
    Support BAM Milestone Modeling (BPEL)
    Sub-Process Calls: Integration Process Call,
    User Interaction: User Decisions (initially not part of this project, but will be covered as well to draw the complete picture),
    Alert Categories
    Enhancements for Process Automation
    Human interaction:
    Integration paradigm (design/ configuration).
    Generic user decision.
    Language dependent texts for end-user display, enriched with variables.
    WS-BPEL 2.0 adoption: Preview and implementation BPEL4People, BPEL-SPE Simple user defined functions can be configured directly in the process.
    reward points if helpful...
    PrasHanT

Maybe you are looking for