Difference between Speed Dial & Fast Dial & Abbreviated Dial

Our company is installing callmanager with a few IP phones (7841, 8831, 8945).
I am documenting how to use the phones.
Based on the user guides for these phones, I cannot tell what the actual difference is between Speed Dial & Fast Dial & Abbreviated Dial.
Does anyone have any guidance on this?
Thanks.
Mac

We have 7945's and 65's but by the looks of your phone you have a directory button.
The speed dials are configured on an available button on your phone.
The abbreviated dials are setup in your self service console as speed dials and are only available on the phone you are setup on. you press the number you configured and hit the abbrDial softkey and it dials.
The fast dials are available in your personal directory which will follow you to any phone as long as you enter your login. When you view your personal directory you can look at your contacts and you can tie your contacts to a fast dial number.
It's been 6 mo so i'm sure you might have found this already :)

Similar Messages

  • Difference between System Performance "Fast" or "Turbo"?

    Anyone know what switching System Performance to "Turbo" on the K8T actually does? I assume it could switch on dynamic overclocking by a percent or two, or perhaps raise the FSB slightly. What else might it be doing? I can't believe it would interfere with memory timings. Anyone know for sure? Bas, you seem to have connections as MSI!  

    At least traditionally, setting a computer from "Normal" (or "Fast") to the "Aggressive" (or "Turbo") setting has enabled many invisible changes (which cannot be set or accessed by a user) that can improve performance at lower FSB frequencies.  Although I cannot say any specific changes made (especially those specific to the K8T Neo), I seriously doubt that they are limited to one single area, or even related to the FSB of the CPU at all.
    -Angler

  • Speed Dial with CME

    Hello guys,
    In server based CallManager, users can go to the "servername/ccmuser address and setup their own seepdials. Is there any way that we can offer this service through CME 3.3?
    Thanks

    Thanks Sankar,
    The only issue is that the CUE user page has access to the same features that an admin has and I don't want that.
    I have a 7940, how many speedial can I configure for this phone? In the documentation it says up to 24 speedials. My question is where is it going to show all those 24 speedials? Would it be on the screen? or under Directory buton, Local Speed Dial?
    And my last question is what is the difference between speed dial and fast dial?
    Thank you for taking the time and responding,

  • Difference between older Extreme and new one

    I have an Airport Extreme that is about 2 to 3 years old.  The difference between speed when I am plugged by ethernet into the network and when I am using the router is significant.  It drops by about 50% or more.
    Can I expect better performance from a new model?  I have mine set at 5GHZ and auto for Channel selection.
    Thanks,
    Deanna

    The new AirPort Extreme 802.11ac......which is really not so new.....can produce wireless signals theoretically approaching the same speed as an Ethernet connection......but.....and this is a big BUT......this speed will only be realized with the 802.11ac AirPort Extreme....IF....
    You also have a new Mac that is capable of receiving an 802.11ac signal....
    and....
    The Mac is located where it has line of sight with the 802.11ac AirPort Extreme.
    To be realistic, if you have a good connection with the new 802.11ac AirPort Extreme and the new Mac is located such that it has line of sight with the AirPort Extreme, you might expect to see a 25% drop in speed compared to the 50%+ that you see now.
    The current AirPort Extreme will be two years old in a few months, and Apple rarely keeps a current model for two years, so there may be a hint in there.

  • Can I have a "Speed Dial" or "Fast Dial" as my home page for Safari?

    Is there anyway to do this?
    I would really like to be able to have Safari set up with some type of Speed dial.
    For those of you who dont know, its basically a home page with about 9 different thumbnails that are constantly logged into their own sites.
    Its very quick and efficient.

    I think he's talking about something like the Fast Dial extension for Firefox (https://addons.mozilla.org/en-US/firefox/addon/5721) but for safari. I use it on firefox and would like to see it on Safari too

  • Speed Dial and Abbreviated Dial

    I have to configure 40 phones with 100 Speed dial/Abbre. numbers. Is there anyways I can configure one phone with these numbers and have this phone publish these  to other 39 phones?
    OR is there a easy way of doing this task?
    I am using CCM 9.x and Cisco 7821 SIP phone. Any help would be greatly appreciated.

    Hi
    You could configure one phone, and then export the phone config (using BAT import/export functions) then edit the output file to copy the speed dials to the other phones.
    On 10.5 you can associate all the phones to one user, and the User Portal allows you to link the phones together so the speed dials are synced. Just found this the other day, but it's not much use to you just now!
    Aaron

  • System-wide Speed Dials

    Is there a way to set up speed dials system-wide in UCM 5.1? We have about 25 remote locations and we want anybody in the company to be able to use speed dials (or something similar) to dial their main number. We don't want to add them to Active Directory because there are other apps pulling from there.

    Depending on configuration, your phone can support several speed-dial features:
    Speed-dial Numbers
    Abbreviated Dialing
    Fast Dials
    http://cisco.com/en/US/products/hw/phones/ps379/products_user_guide_chapter09186a00806453c0.html#wp1009061

  • "Temp Fail" with BLF Speed Dial + Call Pickup

    Good day All,
    I am running CUCM version 8.6.2 and many IP Phones 7962G.
    I have a Manager configured with extension 1001 and his PA with extension 1002. Both extensions are configured in the same Call Pickup Group.
    On the PA IP Phone, the second button is configured as a BLF Speed Dial with Call Pickup for the Manager.
    When someone calls the Manager, she can see that the Manager Line is ringing but when she press the button in order to pick up that calls, she hear a busy tone and the IP Phone display a message that says "Temp Fail". I have checked every thing on both IP Phones and all seems to be correct. Am I missing something may be?
    When I changed the Manager Line from 1001 to 1003, in the same Call Pickup Group, thats works fine. She is able to pick up calls for 1003. But on the CUCM Server, there is no such difference between extension 1001 and 1003.
    Please advise.
    Warm regards,
    J. Kabundi.

    Which PickUp group they belong doesn't matter, don't need to be the same for the BLF PickUp Feature.
    But if they are in the same group as you mentioned: Can the pickup via the normal PickUp Softkey?
    If changing only the Number makes it working i think you may have a problem with the DNs/Partitions. Ever renamed the partition? Try deleting the manager DN, remove the unassigned number from your server, and add it again.
    If it still doesn't work... i would restart the whole server if possible.
    Regards,
    Sven

  • Speed dials

    Hi all experts.
    I have 2 questions kindly take time to answer them
    1) All of you know, how we configure speed dials in mobile phones. We configure them on normal keypad, press the key 2 (for example) for few seconds, and the speed dial number gets dialed. Can we do the same in CUCM7.x or 8.x ?
    2) With reference to the above question, what approach should i take to find the answer on my own ?, i downloaded cucm 7.0 administration guide and feature guide, but it hasnt shown how to configure speed dials :-(, how do you guys search for a specific feature ?
    Thanks

    I am going to assume by "mobile phones" you mean the 7921G or 7925G. Speed dials are a feature of that model and a referenced in the phone's documentation, not UCM. Cisco UCM has no feature called speed dials which is why you cannot find documentation on it. The closest that UCM comes is the speed dial line button type. The UCM-level features that are equivalent are :
    Abbreviated dialing. You press a one- or two-digit index number representing the number you want to dial and then the AbbrDial soft key. This is a per-device setting (i.e. not global). These are configured by the user on the device using /ccmuser or the adminstrator by assigning a Speed Dial line button type to a device. If assigned to a free button it will act as a one-button speed dial. If you associate it beyond the available buttons, the index number shown to the left becomes its Abbreviated Dialing index.
    Fast dials. These are Personal Address Book entries that you have configured as a fast dial through /ccmuser. They are accessed and dialed through the Personal Address Book service. These are per-user settings.
    Translation patterns. Many other PBX systems have an explicit concept called Speed Dials that are globally available to all users. UCM doesn't bother with that feature because Translation Patterns can do that instead. Cisco just doesn't point this out very well. You can create a translation pattern that translates FROM anything TO anything. For example: *411 translates to +16085532447.

  • All the images in my Speed Dial thumbnails have disappeared and I can't get them back.

    All the images in my Speed Dial thumbnails have disappeared and I can't get them back. When I check the settings all the thumbnails have the site shown in the details so should be showing the site in the thumbnail, but they're just blank. I uninstalled Speed Dial and installed it again, but to no avail. Something is stopping the image appearing but don't know what. I paused blocking on Ghostery, but that makes no difference. Any suggestions would be welcome!

    See [[menu bar is missing]].

  • How do I put a pause in a speed dial on a DX650?

    I would like to set up a speed dial for a daily conference call so it will dial the phone number, pause, then add the conference code.
    I tried , and . and # and they are not working.

    I did some more research, and found out that the comma (,) pauses, but the pause is incredibly short so I didn't even notice.  After experimenting, putting in 20 commas between the phone number and the conference code, it worked.

  • How can I set up a calling card on speed dialing?

    I use a company calling card for international dialing. How can I set up a speed dial for the dial number and the password with a pause in between for the international number?  Any clues?

    speed dial: Your smartphone can store nine
    phone numbers that you can call
    with a single keypress. To store a
    speed dial number, touch Phone
    > Menu > Speed dial setup, and
    insert a number in an empty speed
    dial slot.
    To call a speed dial number, touch
    and hold the single-digit speed dial
    number in the dialer screen.

  • Add photo to Speed Dial

    Hello, I have had my Z10 4 days and this forum has been invaluable.  I am becoming very comfortable with things.  I have have added my speed dial contacts but do not seem to be able to save the avitar.  When I go to the contacts page, click on avitar add a photo it still does not appear on the other screen.  Can anyone help?  K

    Kinloch wrote:
    Where do I reset my phone and not reset the whole phone and wipe my memory?  Thanks very much for the fast reply. K
    Do a simple reboot on the BlackBerry in this manner: With the BlackBerry device POWERED ON, remove the battery for a minute, and then reinsert the battery to reboot.
    1. If any post helps you please click the below the post(s) that helped you.
    2. Please resolve your thread by marking the post "Solution?" which solved it for you!
    3. Install free BlackBerry Protect today for backups of contacts and data.
    4. Guide to Unlocking your BlackBerry & Unlock Codes
    Join our BBM Channels (Beta)
    BlackBerry Support Forums Channel
    PIN: C0001B7B4   Display/Scan Bar Code
    Knowledge Base Updates
    PIN: C0005A9AA   Display/Scan Bar Code

  • Regression PR1.1 Speed Dial : restart N8

    After upgrade to PR1.1, when I use speed dial function  the phone automatically restart.
    How to use speed Dial work :
    Go to call function :
    Hit  a number between (2 to 9) then hit big green button.
    Best Regards

    same here, no fix?
    hope anna does not have this bug

  • How to recover Missing speed dials Assistant Console Lost after DBreplication problems

                       Hi everyone,
    Does anybody knows where i can recover lost speeddials (contacts) from Assistant Console (IPMA Solution)  in Call Manager Backups or RTMT files?
    I have 1 cluster with 2 call managers 7.1.3  (PUB and SUB) , the phones registered to SUB and the IP of PUB configured in Assistant Console settings.
    I had a problem with replication of database  between the 2 cucms ,  after i resolved the problem the IPMA solution start to work but some assistants lost part of their contacts in aplication , seems like they return to an old state , they not lost all , but some contacts (maybe the last added) .
    My question is that i want to recover , somehow , the lost contacts , even in the "paper" format , in pub or sub.
    I know tht i can restore the old database , but maybe the old database was corrupted because of dbreplication problems.
    I read already the "Troubleshoot Missing Speed Dials Issue in IPMA   Document ID: 111006" : http://www.cisco.com/image/gif/paws/111006/ipma_speeddail-00.pdf  
    and its useful only to backup the actual contacts , not the missing ones.
    Best Regards.

    Hi Robert,
    We have exactly the same issue.
    We have opened a TAC case and the workaround was to download the new IPMA client from the Cisco website but unfortunatly that haven't solved the issue...
    Have you found something on your side ?
    Regards,
    Nicolas

Maybe you are looking for