Difference in storage types

What is the difference between the basic 13-inch Air's "128GB PCIe-based flash storage" and the non-retina, basic 13-inch Pro's "500GB 5400-rpm hard drive"? I know that 500 is obviously more than 128 but just in terms of type of storage

One is a rotating platter Hard Disk Drive with a motor and moving parts. It connects to the computers HDD interface which has a SATA 6Gb/s transfer rate.
The PCIe SSD is a Solid State Drive with no moving parts. It connects to the computer's internal PCI Express bus that operates at roughly 40 Gb/s or nearly 10 times faster. The PCIe SSD is simply much faster than a HDD or even an SSD that connects to the SATA bus as most do.

Similar Messages

  • In WM how to clear partially difference in an open storage type with one mi

    Hi
    I would like to know how in WM to clear partially differences in an open storage type with one mixed bin not totally counted?
    thanks in advance
    cadanj

    Please do the inventory check for the whole bin.Count the each quant of the material. Difference can be cleared.Use following transactions.
    1.LI01N-Create Inventory document.
    2.LI11N-Enter inventory count.
    3.LI20-Clear WM differences
    4.LI21-Clera IM differences.
    Let me know if u have any other question.
    Regards,
    PRashant

  • Issue with clearing the Differences in 999 storage type in HU managed S.Loc

    Hi Experts,
    We are trying to writeoff the differences stocks which are there in 999 storage type, but getting an error message 'Quantity difference document line item for HU's' with Message class L6 & Message number 606. Any idea how this can be resolved?
    I can see that for this product/batch combination there is another HU in packing area 923 which is acting as a SU because the item level details are deleted for this HU. Could this be the issue for the errror? Would need some pointers to clear this stocks.
    Thanks,
    Harish

    The item details of the HU seems to be have deleted, causing the difference between HU, IM/WM stocks. We have deleted the HU using HUMO & then the HU difference quantity was posted using HUDIFF.
    Thanks,
    Harish

  • Storage Type where differences are posted

    Hi All
    This is the scenario that I have:-
    A 999 storage type has been created in order to post inventory differences into this storage type. The differences posted result in stock count differences, damaged/expried stock posted to different storage bins in the storage type and when there are quantity shortages during Put-Aways, Picking.
    I need a documentation that would help me to improve this process as we are experiencing a backlog of stock still sitting on the 999 storage type and we are looking for a better process on how we can clear these items.
    Regards
    Khuselwa

    Hi
    Clear differences in IM Transaction LI21
    St Type 999 is the ONLY st type from where you can clear differences.
    Ensure that you have the warehouse number and st type 999 and execute.
    In this transaction SAP assumes that you want to clear everything out of 999 and so defaults a tick in to all lines. The storage bin is the count doc number and therefore if you only want to clear count number 2 then you need to deselect the ticks from the other lines. Click on clear 
    This transaction will clear the differences out of 999 and adjust the stock in IM and produce accounting documents for the gains and losses
    I hope that this helps and if you now have your answer please award points as you want to and mark the question as answered so as to keep the forum tidy
    Frenchy

  • No difference qty was posted to 999 storage type

    Dear Experts,
    I confirmed a TO with differences.   The  Confir Diffrences winod pops up in LT12 and I confirm the TO with differences.
    But however, no difference qty was posted to 999 storage type.   999 storage type has no qty
    Why is this so?   what is the config needed?   Please advise
    Regards
    Shetty

    Found answer:  Channged difference indicator

  • Does anyone know what's the difference of storage loation type & bin?

    Hi Experts
      Now we use WM. Hope to consult if we could assgin one locaiton for two location type ?
    Does that mean, for each location type ,it will has its own bin number and physical place?
    Another thing, we hope when locaiton type A is empty , it could create TO auto and inform user to move mateiral from locaiton type B.  COuld it implement in sap? like some stragety ?
    Thanks
    alice

    - One storage location can have "N" number of storage type.
    - One storage type can have "N" number of storage bins.
    I replied for your second part of question in another thread.
    Regards
    Arif Mansuri

  • Difference between Storage Unit type and storage type

    Hi,
    I am confused with storage unit type and storage type.
    Can anyone help me with real case examples.
    I would like to know about Storage unit types and their uses in WM.

    Hello!
    Storage type is a storage area and Storage Unit Type is strategies are used in the warehouse process for creating transfer orders.
    A storage type is a storage area, warehouse facility, or a warehouse zone that you define in Warehouse Management (WM) for a warehouse number. This is a physical or logical subdivision of a warehouse complex that is characterized by its warehouse technique, the space used, its organizational form, or its function.  A storage type generally contains several storage spaces or slots. These are called storage bins in Warehouse Management (WM).
    See also:
    https://wiki.sdn.sap.com/wiki/display/ERPSCM/WMOrganisationalStructure
    http://help.sap.com/saphelp_470/helpdata/en/c6/f838f94afa11d182b90000e829fbfe/content.htm
    Storage Unit Type is putaway strategy, the system processes different storage unit types (for example, pallets) and allocates them to the appropriate section. Often, one storage bin is divided into several smaller sections. Typically, only the same storage unit types can be placed into a storage bin at one time.
    See also:
    http://wiki.sdn.sap.com/wiki/display/ERPSCM/PutawayandRemovalStrategiesin+WM
    http://help.sap.com/saphelp_470/helpdata/en/c6/f844c44afa11d182b90000e829fbfe/content.htm
    Milca

  • HU without inventory management and message L3778 in storage type 999

    Hi experts,
    Need suggestion on the process to add inventory of an HU with status 'HU without inventory Management'. This issue has occurred out of the below scenario:
    1. our warehouse is HU & WM managed.
    2. We have a transfer order for a delivery document requesting to pick up 100 cases of MAT1 which is assigned to HU1.
    3. While confirming the transfer order user has confirmed difference for the full quantity of 100 because the SU/HU was not found in the bin.
    4. The system has set the status of HU as 'HU without inventory Management'. The HU is empty.
    5. system has moved the stock from the bin to difference storage type 999.
    Now user has found the stock for this HU and he wants to post the stock back into the bin. system does not allow to move the stock back to bin using LT01 as we get error message 'L3 778'.
    What will be the best practice to get the stock back into the bin and post the stock into the same old HU.
    Is there a process wherein we can post this stock to another bin and repack into the old HU?
    Thanks,
    Harish

    Thanks Manish on the hint. I was able to transfer stock to partner location and then bring back to original Storage type/Bin. Below steps was used to fixed the issue:
    1. Initiate a transfer of stock from WM/HU Sloc where the IM stock resides into Sloc 9099. An outbound delivery is created during this process.
    2. Create a transfer order with reference to delivery and pick the stock from 999 storage type.
    3. Create a Pick HU using LH01 and assign the HU on the pallet to the transfer order.
    4. Confirm the transfer order using LT12.
    5. Perform PGI for the delivery.
    6. Use HUMO to display the HU and then you can transfer the stock back to WM/HU location using the storage location transfer option available on the HUMO screen(EDIT à change HU posting à Storage location)
    7. Perform Bin to bin transfer to move the SU from 921 storage type to putaway the HU/SU back to the destined Storage type/Bin.
    Best Regards,
    Harish

  • Create multiple TO's from IM storage type

    Bit rusty on SAP transactions.
    If I have stock in a 'Differences' Storage Type (non-SU) that I want to bring back into storage on 30 different SU's is this possible?
    Other than one by one using LT01. Can I use LT04 in some way?

    Pete,
    You can also mention a specific qunatity in Material Master WM2 as LE quantity.
    Once done you can go ahead with LT01 with Full quantity & that will split in multiple line Items.
    Please use TO creation screen control as 1 i.e. Putaway prep that will help you to entre multiple destination Bins (if differs)
    Thanks,
    mahesh

  • List of standard Interim storage types - WM

    What are the standard Interim storage types
    In my system people have created few starting with 9 hence not able to diffrentiate which are standard and which are non-standard
    Thanks

    The Standard Interim storage types starts with 9**.
    In the table T331, the below fields will have 'X', which shows everything is allowed.
    MISCH - Mixed storage
    ZULAG - Addition to stock
    NEGAT - Negative stock qty
    LENVW - Storage Unit Management (will be empty)
    The reason for the Storage Unit Management will not be selected was the HUS can packed and repacked with no restrictions.
    I hope you can find the difference based on that.

  • Regard an error "Storage type & notsuitable as interface (SU mgmt is active

    Hi All,
    I am trying to do the inventory clearing in both warehouse and Inventory management using the transactions LI20 and LI21 after counting the inventory. But whenever I am trying to do the writeoff's I am facing with an error "Storage type & not suitable as an interface (SU management is active)"
    I couldnt able to figure out the main cause for this error. Your valuable suggestions would be highly appreciated.
    Regards,
    Shane

    Hi Jürgen L,
    My objective is to do physical inventory and of ther are any differences then write them........in this sytem Both Grants and fund management is involved?
    I am getting this message while I am doing LI21. And you have suggested that, the difference storage type SU managed. which is a 999 storage type. and  this is not SU managed.
    I would also like to ask regarding the clearing of differences in warehouse and Inventory mangement. I am using the mvmt types 711 and 712, But what account documents will get generated. I am thinking there will be no account documents that will get generated. Adding to this I am getting "Account 6701 requires an assignment to a CO object with Message no. KI235". If we do this assignment to this CO object......... doesnt the transaction go and hit the balance sheet account.
    I am lil baffled with this whole process. If you could give me your valuable information, that will help me a lot.
    Shane.

  • WM - Storage type 001 is not suitable as an interim storage area -

    Hi,
    When i'm doing Migo, the blw error has came, pls advise , how solve it..
    seems, some where i made wrong config.. These process i was trying in our ides server..
    Storage type 001 is not suitable as an interim storage area
    Message no. L9022
    Diagnosis
    You have attempted to execute a posting to a dynamic coordinate in a storage type for which a putaway strategy is defined. Dynamic coordinates, however, are provided only for storage types without a putaway strategy.

    thanks Raman
    pls tell me now , where i have to check the config.. and where i may did the mistake.
    for ur info, ref to sdn A08- conf guide as per blw , i made the conf..
    3.1 Full WM Basic Settings     
    3.1.1 Defining Control Parameters for Warehouse Number     
    3.1.2 MM-IM Storage Location <-> Warehouse Number     J01
    3.1.3 Defining Storage Type                                              001- high rack system
    3.1.4 Defining Storage Section                                            001- Fastmoving
    3.1.5 Defining Storage Bin Types                                   P1-BIN HEGIHT 1 MTR
    3.1.6 Defining Blocking Reasons                                           1
    3.1.7 Defining Storage Bin Structures     
    3.1.8 Defining Storage Type Indicators                                1
    3.1.9 Defining Storage Unit Types                                    E1
    3.1.10 Defining Storage Section Indicator                        001- Fastmoving
    3.1.11 Defining Bulk Storage Indicator                                      B1
    3.2 Strategies     
    3.2.1 Activating Storage Type Search     
    3.2.2 Activating Storage Section Search     
    3.2.3 Activating Storage Bin Type Search     
    3.2.4 Defining Sort Sequence for Putaways (Cross-line Stock Putaway) Definition of Sort Field in Storage Bin     
    3.2.5 Defining Strategy for Pallets     
    3.2.6 Defining Putaway Strategy for Bulk Storage     
    3.2.7 Defining Strategy for Stringent FIFO     
    3.2.8 Defining Strategy for Large/Small Quantities Determining Search Sequence     
    3.3 Activities     
    3.3.1 Defining Requirement Categories     
    3.3.2 Defining Shipment Types     
    3.3.3 Defining Movement Types     
    3.3.4 Defining Stock Transfer and Replenishment Control Defining Replenishment Control for Storage Type     
    3.3.5 Setting up 2-Step Picking     
    3.3.6 Defining Confirmation     
    3.3.7 Print Control     
    3.3.8 Defining Default Values     
    3.3.9 Defining Types for Storage Type     
    3.3.10 Defining Difference and Document Limit     
    3.3.11 Clearing Difference (Interface with IM) MM-IM Movement Types for Clearing Inventory     
    3.3.12 Clearing Difference (Interface with IM)  Do Not Allow Clearing in Storage Types     
    3.4 Interfaces     
    3.4.1 Allowed Negative Stocks in Interim Storage Types Allowing Negative Stock for Each Storage Type     
    3.4.2 Shipping Shipping Control per Warehouse Number     
    3.4.3 Shipping  Requirement Types of Delivery Documents     
    3.4.4 2-Step Picking     
    3.4.5 Creating Automatic Transfer Order     
    3.5 Manual Activities     
    3.5.1 Maintaining Number Range and Assignment     
    3.5.2 Maintaining Number Range for Physical Inventory     
    3.5.3 Creating Storage Bins     
    3.5.4 Generating Interim Storage Bin
    Edited by: UJ on Mar 4, 2009 7:16 AM

  • Counter KF with 1 & 0 and difference between data type NUMBER (DEC) and INTEGER (INT4)

    Hi,
    I need to create a counter kf which should populate 1 and 0 to this counter field. Please let me know is there any difference between data type
    NUMBER (DEC) and INTEGER (INT4).
    Please suggest.
    Thanks & Regards,
    Pavan kumar

    Hi Pavan,
    The basic difference between Number(DEC) and INT4 is its internal storage in system.
    For Number (DEC) - Value internally stored as packed number with 3 decimal places whereas INT 4 as 4 byte integer without decimal places.
    For counter KF, you can go for INT 4.
    Hope this helps.
    Thanks

  • User Exit for Put Away for multiple storage type

    Hi All ,
    we are using the exit EXIT_SAPML03T_002 for doing some capacity calculation and bin selection while doing a put away process in Ware house .
    now i want to have two different type of storage types
    say
    A and B ,
    if their are no empty bins in storage type A , then as per storage section search strategy the material should go in B storage type.
    Both the storage type has next empty bin search strategy with user exit activated.
    The difference between the two storage type is their individual capacity which is maintained in a custom table .
    I am facing the problem that the exit is getting triggered only once .
    ie. it will check for storage type A if the criteria is not met at a later stage while bin allocation , the system is not triggering the exit for B storage type .
    do i need to do all validation and possibilities of not getting placed in storage type A in the exit . or does this exit will trigger for each storage type as per strategy if for any reason the stock is not placed in the previous storage type ?

    Hi Experts
    Thanks for the response,
    As i tested for the 561 movement (initial upload) we need to do the put away manually.
    So the system will not suggest Full qty to move to one Bulk and partial to different.
    But for normal Goods receipt process the goods will be automatically placed to different storage type
    based on the search strategy and in the Bulk structure we need to unchek the  partial pallet allowed.
    If anybody has difference pls revert
    Regards
    Depin

  • Physical storage types

    I have  a question....
    are the interim storage areas physical storage areas or just dummy areas we use to update the stock when GI and GR happens and to clear differences.... I know tht putwaway strats and picking strats are not defined for these/... So I am thinking these are just dummy storage areas we define to handle Negative stocks etc... Am I wrong... Please correct me

    Hello
    The interim storage types are physical or logical depending upon the client business process.
    Normally big warehouses having these interim storage types and the goods will unloaded and then sent to inpsection or they will repacking or skidding or lebelling will be done and then transferred to the storage bins. Similarly goods will be picked from different storage type to interim storage location and then delivered to teh customer.
    Warm regards
    Ramarkishna

Maybe you are looking for