Different between ASA-5520-K9 & ASA-5520-K8

Hello Dear ...
We were using ASA-5520-K9 with  ASA-SSM-AIP-20-K9 but recently found some hardware problem in our running ASA. Now cisco want to replace with ASA-5520-K8. can any one please advise me what features we will miss or get.
thanks in advanced.
regards/
Mannan

They are exactly the same hardware. It's the license that makes it K9 which you can request from the licensing team at Cisco.

Similar Messages

  • Communication problem between ASA 5510 and Cisco 3750, L2 Decode drops

    Having problem with communication between ASA 5510 an Cisco Catalyst 3750.
    Here is the Cisco switch port facing the ASA 5510 configuration:
    interface FastEthernet2/0/6
    description Trunk to ASA 5510
    switchport trunk encapsulation dot1q
    switchport trunk native vlan 50
    switchport trunk allowed vlan 131,500
    switchport mode trunk
    switchport nonegotiate
    And here is the ASA 5510 port configuration:
    interface Ethernet0/3
    speed 100
    no nameif
    no security-level
    no ip address
    interface Ethernet0/3.500
    vlan 500
    nameif outside
    security-level 0
    ip address X.X.X.69 255.255.255.0
    There is a default route on ASA to X.X.X.1.
    When I try to ping from ASA X.X.X.1 i get:
    Sending 5, 100-byte ICMP Echos to 31.24.36.1, timeout is 2 seconds:
    Also in the output of show interface eth 0/3 on the ASA i can see that the L2 Decode drop counter increases.
    I have also changed the ports on the Switch and ASA but the same error stays.
    Any thoughts?

    I don't see anything wrong with your trunk configuration; I have a similar one working between an ASA 5520 and a Catalyst 3750G.
    Maybe you should adjust the "speed 100"?  In my experience, partial autoconfiguration results in duplex mis-matches, which results in dropped packets.
    I'd try removing the "speed 100" and letting the ASA port autonegotiate with the switch.  Alternatively, have both sides set
       speed 100
       duplex full
    and see if things improve.
    -- Jim Leinweber, WI State Lab of Hygiene

  • Change MTU for just one Site-to-Site VPN between ASAs?

            Hi -
    I'm setting up a Site-to-Site Cisco VPN between ASAs. I'm being told by the remote site engineer to set the maximum MTU at 1362.
    Is it possible to set the MTU for one specific site-to-site VPN on my ASA 5510 Security Plus to MTU 1362? I see my interfeces are all set at 1500.
    If not, would you recommend I setup a subinterface on my inside network router and a subinterface on the ASA with an MTU of 1362 to get around this issue? Then use this subinterface for traffic from my inside network to transverse through prior to hitting the VPN.
    Thank you.

    I would not worry too much about UDP traffics.  I rather concentrate on TCP traffics because almost all of the issues will be TCP.
    Therefore, I would set the MSS value to 1362 or may be like 1300:   sysopt connection tcp-mss 1300
    That will solve most of  your issues.

  • Unable to print from HQ to Branch through the VPN tunnel between ASAs

    We have site to site VPN configured between ASAs. The VPN tunnel is up and running as desired except for one printer in the subnet. the users in the Hq cannot print in the branch office printer. I have allowed the ip protocols for the printer subnet but still it is not working. When I do a packet trac the traffic for the printer is allwed through the tunnel.
    Can anyone suggest what can be preventing from printing?

    When other printers in the same subnet can be reached, I would first control the IP-settings of the printer. In my experience it's most likely a wrong subnet-mask or gateway.

  • Difference between ASA-SM1 and FWSM.What is the throughput of each of them?

    Can any1 tell me wat is the difference between ASA-SM1 and FWSM
    and what is the throughput of it?
    Thanks in advance
    Khem

    The FWSM is end of sale. It has been replaced by the ASA-SM1.
    See the following link for details of the performance differences between the two devices:
    http://www.cisco.com/en/US/prod/collateral/modules/ps2706/ps11621/qa_c67-662207.html
    Don't forget to rate all posts that are helpful.

  • IPSec ikev2 between ASA and Cisco Router

    Hi,
    i try to do IPSec with ikev2 (SHA2) between ASA and Cisco Router, without success. Any one can help me ?
    - Remote site (Router) with dynamic public IP -> Dynamic crypto map on the ASA
    - Authentication with Certificats
    - integrity sha2
    I try a lot of configurations without success.
    Thanks for your help.
    Mic

    The more secure ike policy should have the higher priority which is a smaller number. So I would configure there the following way (policy 30 only if really needed):
    crypto ikev1 policy 10
    authentication pre-share
    encryption aes-256
    hash sha
    group 5
    lifetime 28800
    crypto ikev1 policy 20
    authentication pre-share
    encryption aes-256
    hash sha
    group 2
    lifetime 28800
    crypto ikev1 policy 30
    authentication pre-share
    encryption aes
    hash sha
    group 2
    lifetime 43200
    The Cisco VPN Client is EOL and not supported any longer. And yes, by default DH group 2 is used. But that can be configured by a parameter in the PCF-file.
    There are two (three) better options:
    Best option with very little needed configuration:
    Move to AnyConnect with TLS. AnyConnect is the actual Cisco client that is also supported with Windows 8.x. The legacy IPsec client isn't.
    Best option with a little stronger crypto but more configuration:
    Move to AnyConnect with IPsec/IKEv2. 
    Move to a third-party client like shrew.net. I didn't use that client since a couple of years any more, but it's quite flexible and also has a config for a better DH-group.
    For option 1) and 2) there is an extra license needed, but thats not very expensive.

  • Unable to establish site to site vpn between asa 5505 an 5510

    Hi ALL expert
    We are now plan to form a site to site IPSec VPN tunnel between ASA 5505 (ASA Version 8.4) and ASA 5510 (ASA Version 8.0) but failure, would you please teach me how to establish it? Any reference guide?
    Hugo

    Here are the links to the cisco config-guides:
    http://www.cisco.com/en/US/docs/security/asa/asa80/configuration/guide/site2sit.html
    http://www.cisco.com/en/US/docs/security/asa/asa84/configuration/guide/vpn_site2site.html
    In addition to VPN you need to look into NAT exemption:
    http://www.cisco.com/en/US/docs/security/asa/asa80/configuration/guide/cfgnat.html#wp1043541
    http://www.cisco.com/en/US/docs/security/asa/asa84/configuration/guide/nat_overview.html#wpxref25608
    http://www.cisco.com/en/US/docs/security/asa/asa84/configuration/guide/nat_rules.html#wp1232160
    And lots of examples:
    http://www.cisco.com/en/US/products/ps6120/prod_configuration_examples_list.html
    Don't stop after you've improved your network! Improve the world by lending money to the working poor:
    http://www.kiva.org/invitedby/karsteni

  • Difference between ASA 8.3 and 8.4 IOS VERSION?

    What are major differences between ASA 8.3 and 8.4 IOS VERSION?
    Also data flow?

    The release notes outline the differences in each version of ASA software. You can find the ASA 8.4 Release Notes here.
    I don't understand what you're asking about data flow.

  • What is the different between Sharepoint fast search service and Sql server fulltext search?

    HI ,
    I want to kow what is the different between Sharepoint fast search service and Sql server fulltext search?
    Or Can I abstract the Sharepoint fast search from the Sharepoint platform as a isolate component?
    Thank you.
    James

    They are very, very different beasts.
    Firstly FAST Search for SharePoint is the old name for the product and is only relevant for SharePoint 2010 not 2013. It got merged into the standard SharePoint search for the 2013 release.
    SharePoint search is aimed at providing a Bing or Google like experience for your intranet content, as well as providing some nifty features that are purely SharePoint releated along the way. That means it can crawl SharePoint content, file shares,
    outlook mailboxes, internal and external websites and probably fifty other different things if you really tried. Whilst i'm not an expert on SQL full text search I believe it's intended to provide a search feature for content held within SQL databases
    and tables.
    Can you run SharePoint purely for Search? Yes, definitely.

  • What is the different between Logical complex join and Physical join?

    hi,
    Do somebody know what is the function different between logical complex join in BMM layer and physical join in physical layer?
    Thanks.

    Thank you very much1
    I understand their differentiation:
    In the BMM Complex join (intelligent), means OBI picks the best way from possibly many different ways to join using physical join. FK join forces the same join always, which limits flexibility.

  • Exchange rate is different between records in OB08 and records in document.

    Hi Gurus,
    The exchange rate is different between records in OB08 and records in calculated amount in line item. How does it happen? Not all of the documents in the same period has this problem.
    For example, a document A created by FB05 on Jun 30 2010.
    In OB08, the exchange rate is 6.80000. This rate was the same in the header of document A.
    In the line item of doc A, I calculated the amount for line itme 1 and 2. Line itme 1 shows the exchange rate is 7.90000. Line item 2 shows the exchange rate is 16.0000. ( The exchange rate is not that exactly an interger. I put a similar exchange rate as an example.)
    Could you please throw some light on these? Why some documents are okay but for some, the exchange rate is so different?
    I just found that the exchange rate of some of the document line item calculated is from another currency. It shows in the line item (in question) button "More Data". Shall I know how the exchange rate was got from another currency exchange rate?
    Thank you.
    Emma
    Edited by: qun yang on Aug 2, 2010 10:49 AM

    Issue solved by below solution:
    Existing:
          append lines of vit_final to s_s_if-maxsize to e_t_data.
          delete vit_final to s_s_if-maxsize.
        else.
          append lines of vit_final to s_s_if-maxsize to e_t_data.
          delete vit_final to s_s_if-maxsize.
    New:
          append lines of vit_final to e_t_data.
          delete vit_final to s_s_if-maxsize.
        else.
          append lines of vit_final to e_t_data.
          delete vit_final to s_s_if-maxsize.

  • What is the different between payment methods Wire and EFT

    Hi All
    can anybody tell me What is the different between payment methods Wire and EFT ?
    Regards ;

    WIRE:
    Wire is transfer of amount due directly to the supplier's bank it is an electronic transfer of funds
    This mode of payment is used for international suppliers.
    It can be paid in foreign currency or USD.
    Wire payments are same day payments.
    EFT:
    EFT ensures funds transfer from one bank account to another using electronic links.
    Can be used to make payments into domestic banks (within US) in USD only.
    It is faster than check payments.
    Hope this helps.

  • Report to Find different between PCR & Schemas

    hi guru's,
    Can Any tell me the Report to Find different between PCR & Schemas in Two Clients,(For examle from 4.7 to 6.0)
    Regards,
    Bala

    Hi Bala,
    The following link will help you.
    PCR and SCHEMAS
    Thanks & Regards,
    Sandip Biswas

  • Payment terms different between sales docs

    Hi Gurus.
    Why do I have payment terms different between sales doc and billing doc for the same customer?
    Detail: the sd and company code vision has the same value in customer master data (xd03, vd03).
    Thanks in advance!
    Renato

    Dear Renato
    Go to VA02, input the sale order and execute.  There click on Environment from top menu bar followed by changes.  You would find four options to choose.  Select
    -  Additional info and
    -  Time of Change
    This would give you who have changed the datas related to that sale order.
    thanks
    G. Lakshmipathi

  • Why do my RAW files appear different between programs?

    I have rendered a series of three RAW images as an HDR file in Photoshop CC, saved as a 16-bit TIFF file, and imported it into Lightroom. The image appears different between the two programs. The Lightroom image appears to have some editing done already and is not nearly as flat as the image in Photoshop. I have made sure my Adobe software is up to date concerning both programs and the camera raw information that can be updated via Adobe.

    The iPad stores the raw photo data, but displays an iPad optimized version of the original image in its place.
    This image is usually an optimized JPEG image, so the quality will not be the same as the raw image file.

Maybe you are looking for

  • Bluetooth connection with Lexus and Storm 9530

    Been trying to connect the bluetooth in the lexus with the storm.  it connects, then drops the connection.  it does not connect when you turn the ignition on, as it did with Motorola V710....not the car's issue, seems like the phone needs something c

  • Sound on/off by click a button in flex4????

    hello everybody, i want to make a website by flex.in that have sound  effect. i want when i load page have sound and if i don't want to listen  i can click button.the sound will stop play and else. But i don't know  how to make on/off sound by a butt

  • IPhoto Library won't open, says need to update iPhoto, but latest version is installed

    I photo won't open, window says to update to latest version and only option is to quit. I have latest version, what can i do?

  • Why should I buy Toshiba in the future?

    I want to ask what is the point of buying Toshiba for the future? What should motivate me? I know that their laptops have quite cheap price for the products they include, but with such a terrible support? I have Qosmio F50-125. I bought it 3 years ag

  • Defaulting Varient on selection screen

    Hi All,   For my program i have created one varient.which i have to default that varient when ever i executed that program.Is there any way  that i can do this. Thanks.