Different SSID on AP's with one controller

We have one 4404 and 12 Ap's 1242: two on every floor. I want is AP's on every floor have their own SSID (differ from others). How can I do it?
Any ideas greatly appreciated.

Vlad,
You need to configure wlan override on the ap for each radio. So basically you need to click on wireless and then click on 802.11a/n or 802.11b/g/n and configure the radio. Wlan Override is located on the bottom left side. Enable it and then choose which SSID you want on that AP.

Similar Messages

  • Control only the software instrument of one channel strip at a time with one Controller

    Hi people,
    I have a Nord Lead 2 and a Korg Nanokontrol and I want to use these as Midi controllers in the following way, but don't really know how to set up the system:
    I have 4 Channelstrips and each has the free software instrument Tyrell N6 inserted. I have the opportunity to change the volume of each channel strip with my faders on the Nanokontrol which works fine and gives me the opportunity to make layers and change also to only use one sound at a time. And this works fine. However, now I want to have the opportunity to change the parameters of each Tyrell with my Nord Lead. But with 4 channelstrips each with a Tyrell N6 I want to have the opportunity to only somehow manipulate only one instance of Tyrell at a time and change the channelstrip for which the Nord Lead manipulates the Tyrell. Is there an opportunity in Mainstage to do that?
    Hope it is understandable. Help would be really much appricated. Looking forward to hearing from you.

    Hi DaCaptain,
    Thank you very much for your answer. I tried it yesterday, but it doesnt really work for me to be honest. The thing is that I really wanna stick to one patch, so that I can have like one patch for each song.
    However, if you might be interested I found a way to do it yesterday on my own. This is how I have done it:
    In Layout-Mode
    - Create Controls for each instance of Tyrell. For my purpose I created 4 times:
                 - controlls for the Filter Section
                 - controls for ADSR1
                 - controls for ADSR2
    - So you have 4 Sections of controllers in Layout Mode. Each meant to controll one Tyrell Instance
    - Now each section gets its own Midi Channel. So all the controllers of section 1 respond to MIDI Channel 1 and the controllers of section 2 respond to MIDI Channel 2 and so on. 
    - Now you tell the Nord Lead that it should send via MIDI Channel 1 and you assign the Cutoff-Controller of the Nord Lead to the controller (the one of the first section) that is suppose to control the cutoff of the first Tyrell. And you proceed this way until all the controllers of the first sections are assigned. Then you swith to MIDI Channel 2 on the Nord Lead and assign the Cutoff-Controller of the Nord Lead to the controller (the one of the second section) that is suppose to control the cutoff of the second Tyrell. And here again you proceed this way until all the controllers of the second sections are assigned. Then you go on with the third and fourth section taking MIDI Channel 3 and 4.
    In Edit-Mode
    - In Edit Mode now you of course assign the controllers to the functions in each Tyrell
    Result
    - Now you can switch between the MIDI Channels on the Nord Lead. This is quiet easy because you can assign a MIDI Channel to one of four buttons on the Nord Lead.
    - So if you switch to MIDI Channel 1 you can controll the functions of the first Tyrell and if you switch to MIDI Channel 2 you can controll the functions of the second Tyrell. And all in one Patch with only one controller which is even from the nineties. I find this really great. The only problem is that the Layout might get really messy, if you try to maybe control more functions of each Tyrell. And I really think maybe Mainstage in future could give us the opportunity to create bigger Layouts - maybe with different Windows or something.
    Hope you might find this interesting or even helpful.
    See you 

  • Can I use 2 different iPhones (and iTunes libraries) with one ATV2?  How?

    My wife and I just bought an ATV2. We both have and use iPhone 3Gs's. I installed the remote app on both phones, but I am only able to control the ATV2 with the first phone I synced with ATV2. It doesn't seem that ATV2 cares what library it links to since the user has to turn on "Home Sharing" in their individual iTunes account. ATV2 appears to be set up so that you can choose what library you want to use (Under the settings). So can I use two different iPhones with one ATV2?

    You can home-share multiple libraries but only use one account at a time. So both phones would need to be signed in under the same apple ID.

  • Sync various profiles with different preferences across two computers with one account

    For security reasons I added a second firefox profile on my machine for banking, taxes etc with very restrictive permissions.
    I set up sync with the new profile and another name in sync preferences (first sync names were 'hostname', I called the new 'hostname'_bank.
    Now different settings get mixed up. In my user profile I find settings from my bank-profile, and with my bank-profile user-preferences show up, which is quite annoying.
    Any suggestions (except using different accounts)?

    Don't sync '''''Preferences''''' in that "bank" Profile.

  • How can I share different sources to multiple Apple TV with only one controller (Mac Mini)

    Here's the setup
    3 TV's in 3 different rooms each connected to 3 different Apple TV.
    It is self-explanatory has how to share the SAME source to 2 or 3 of the Apple TV.
    What I want to know: Can we manage Apple TV's in a way that I can share 3 DIFFERENTS source with ONE controller, let's say a Mac Mini or PC using AirParrot.
    Im open to third-party apps as this is my only complaint for using an easy and affordable setup.
    Regards.

    I have a WLAN at home conneting Mac mini (late 2009), PS3 slim and xbox 360 in the living room and I would love to share whats on the Mac mini with AT3 in the guest room upstairs, physically it wont be possible to control both screens at the same times. The files I have are on external HD connected via firewire + USB to Mac mini and they are a mix of avi, mp4, mpeg etc. I'm talking about 3 TB of movies and series (its still legal here in Dubai to download ;-)). starting to convert such amount of files its not an option. AirParrot is a good option when I have media stored on my MacBook pro and would like to play it no AT3 but I used Beamer it works great for such function.
    any ideas folks ?

  • Controller different ssid

    Hello all
    i use cisco controller and LW access-points.From one access-point i broadcast two SSID.Is it possible to change wireless channels for different SSID ?
    For example in one access-point SSID 1 is wireless channel 6 and the other SSID is 11 ?
    Thanks

    Hello.
    You can only have one channel per radio.
    on 2.4 GHz radio, you can NOT have different SSIDs on different channels.
    Regards,
    Amjad
    Rating useful replies is more useful than saying "Thank you"

  • Storagetek 2510 iscsi - linkaggregation possible with only one controller ?

    Hello,
    I want to test a sun storagetek 2510 iscsi array connected to my M3000. So we bought a 2510 - but only with one controller.
    An additional NIC - 1000g0 and 1000g1 was installed in M3000 for iSCSI traffic. M3000 and 2510 are connectected together via a GBit switch.
    Everything looks good - merely the performance is bad. A look at the CAM SW tells me that all traffic runs only via one interface A/1:
    Controller A Baseline Time: 5. Mai 2009 12:19:36 CEST
    Controller B Baseline Time: 5. Mai 2009 12:19:36 CEST
    MAC Transmit Statistics - iSCSI Host Ports (2)
    A/1      1171093      80695426      0      0      0      0      0      0      0      0      0      0      0      0      0
    A/2      0      0      0      0      0      0      0      0      0      0      0      0      0      0      0
    The targed is well configured - also mpathadm:
    mpathadm list lu
    /dev/rdsk/c3t600A0B800049DCA80000063D49E5FD1Fd0s2
    Total Path Count: 2
    Operational Path Count: 2
    /dev/rdsk/c3t600A0B800049DCA80000064049E5FD31d0s2
    Total Path Count: 2
    Operational Path Count: 2
    # iscsiadm list target-param -v
    Target: iqn.1986-03.com.sun:2510.600a0b800049dca80000000049db7a0d
    Alias: hb1-box
    Bi-directional Authentication: disabled
    Authentication Type: NONE
    Login Parameters (Default/Configured):
    Data Sequence In Order: yes/-
    Data PDU In Order: yes/-
    Default Time To Retain: 20/-
    Default Time To Wait: 2/-
    Error Recovery Level: 0/-
    First Burst Length: 65536/-
    Immediate Data: yes/-
    Initial Ready To Transfer (R2T): yes/-
    Max Burst Length: 262144/-
    Max Outstanding R2T: 1/-
    Max Receive Data Segment Length: 8192/-
    Max Connections: 1/-
    Header Digest: NONE/-
    Data Digest: NONE/-
    Configured Sessions: 2
    Now my fear: do I need the second controller to establish a 2 GBit connection ????
    Thanks for your help.
    best regards
    blackforester

    Hello,
    one additional info from CAM SW:
    both interfaces are connected - see receive statistics - 43 broadcasts were received via interface A/2.
    MAC Transmit Statistics - iSCSI Host Ports (2)
    A/1      2007504      136072106      0      0      0      0      0      0      0      0      0      0      0      0      0
    A/2      0      0      0      0      0      0      0      0      0      0      0      0      0      0      0
    MAC Receive Statistics - iSCSI Host Ports (2)
    A/1      3882266      5520300286      0      43      0      0      0      0      0      0      0      0      0      0      0
    A/2      43      2752      0      43      0      0      0      0      0      0      0      0      0      0      0
    best regards,
    blackforester

  • How Labview can interface with RC controller

    I am tasked by my supervisor to find out the different interface Labview can use with RC controller. 
    I am currently new to Labview, therefore it would be great if anyone can give me some inputs about it.
    Thanks a lot  

    Hi there
    In order for me to transfer my Labview data from my PC to a Futaba T10CAP controller (http://www.astramodel.cz/manualy/futaba/futaba_10c​p_eng.pdf), I will need a hardware to do the linkage. 
    PCTx (http://www.endurance-rc.com/pctx.php) is one of the hardware device that enables me to do such a thing but their Labview demo problems doesn't work on the PCTx. Therefore I am looking for an alternative hardware solution where my Labview can interface with the RC controller. 
    Welcome any input! Thanks and regard =) 

  • Need help configuring: 2 wireless routers with 2 different SSID's on one network

    Hello everyone: 
    I've been reading around on the forum trying to find the answer to this question, but have not found any clear cut answer that satisfies all my requirements.  A more in-depth explanatiion.
    I have 1 IP address coming in via cable modem.  I want to configure two wireless routers (one secured with WPA-TKIP, and one unsecured--a "guest network" if you will) each with different SSID's.  The secured network would be for my server, home PC's, IP webcams, DynDNS updating; while having an unsecured wireless router that friends and family can access.  Ideally, I do not want anyone who accesses the unsecured wireless router to be able to get access into my secured network.
    Can someone please tell me if this is possible.  I think it is based on some posts I have already seen, but specific details about how to do it would be appreciated.  Additionally, my DynDNS has to still be able to update with my ISP's IP so that I can access my server and home webcams.
    EQUIPMENT
    2 - WRT54G
    1 - EZXS55W
    1 - WVC200
    1 - WVC54GC
    (all of my stuff --webcam, server, dyndns, etc -- is working currently on my secured network. I just need to add the unsecured network)
    I know this is a lot, but I would appreciate any help.  THANKS.
    Solved!
    Go to Solution.

    You must have the main WRT54G router connected to the modem. Set up the secured wireless network on the main router. Connect all your wireless computers or devices to the main secured wireless network.
    Let's consider the IP address of the main router is 192.168.1.1.
    Now connect only one computer to the Port 1 on second wireless router.
    Open the setup page of the second wireless router. Change the wireless settings, SSID, unsecured.
    Change the IP address of the second router to 192.168.2.1. Save the settings.
    Connect the cable from the Ethernet port on the main router to the Internet port on second wireless router.
    Power cycle the second wireless router.
    Now the guest computers connected to the second wireless unsecured wireless network will be able to access the Internet only. They will not able to see the computers or devices connected to the first wireless router.

  • Can one controller affect two strips differently?

    I'm new to Mainstage, so bear with me if my terminology is a bit off.
    I want to have have two channel strips that are each controlled by the same pedal. Both patches are programmed to receive CC11.
    But I want the pedal to have the opposite effect on each of the strips. I want Channel Strip 1 to increase in value while CS2 decreases in value. Is there a way to program this in Mainstage without having to go into the VI's patch itself to reprogram?
    Another way to ask this question: Is it possible to program one controller to have different effects on two different channel strips?
    Thanks

    Hi
    Mainstage 2.2 is a "paid update", only available via the Appstore.
    The 'multiple mappings' facility that we have been talking about is also available in MS 2.1
    CCT

  • How can I associate 2 appleids with one account or use a different Appleid for imessage as described in another post?

    How can I associate 2 appleids with one account or use a different Appleid for imessage as described in another post?
    I have rejoined the iPhone community, not with one iPhone but with two. My wife agreed to move from the unenlightened!
    I have set up both under my apple account and want to keep it that way. But I do not want iMessages going to both phones. I would like separate message queues but share all apps and other purches from the store.
    I have created a separate AppleID for her but under Settings>Message>Receive At (it currently says 2 addresses) > ... will not allow me to change the current eMail address and when I add hers (her appleid) it errors out. The only thing I can do in the Apple ID field is to manage my account and not change it to hers.
    How can I have 2 iPhones (and my iPad) on the same account but have separate identies?
    Thanks,
    LpGrumpy

    1. Yes. Restart with the Option key held down as needed.
    2. No, it won't be a problem.
    (83373)

  • How to use two seperate iPods with one iTunes. Different Music Preferences

    My Wife and I both have 80 Gig iPods. We like different Music. How can we both use the same Windows XP computer and have different music lists?

    See: How to use multiple iPods with one computer
    Forum Tip: Since you're new here, you've probably not discovered the Search feature available on every Discussions page, but next time, it might save you time (and everyone else from having to answer the same question multiple times) if you search a couple of ways for a topic, both in the relevant forums, in the User Tips Library and in the Apple Knowledge Base before you post a question.
    Regards.

  • Multiple IOS devices with one apple id and different PCs to synch

    I have 2 macs, 1 Apple TV, 2 iPhones, 2 iPads, 3 iPods and 1 windows pc.
    I would like to:
    1) sync each of them with one of the Macs using the same apple Id;
    2) connect with FaceTime with each of them separately (at least the iPads and iPhones);
    3) synch one phone with the Mac for music and my work PC for apps.
    What should I do using my unique apple I'd?
    Txs,
    Roberto

    When you say "sync", are you talking about physically having songs, movies, etc on your computers and devices?  Or simply want to access those files on those computers and devices?  *Syncing is different from Home Sharing but you are in the Home Sharing discussion forum.  That is why I am asking.
    If they are all in the same network and just want to access them or listen/watch them, all you have to do is turn on Home Sharing for all of your machines and devices with the same account.
    For Mac/PC desktops, you can turn on Home Sharing in iTunes 11.  Go to File > Home Sharing > Turn on Home Sharing.  Do this for all machines.  After doing that, you go to the media selector button at the top left to see your Home Shares.  Or you can enable the sidebar by going to View > Show Sidebar.  From there, just connect to your other computers and you will able to listen or watch to your content.
    For your devices, turn on Home Sharing in Settings.  Go to Settings > Music or Video > Home Sharing and enter the same Apple ID and password.  You can listen to songs in Music and watch videos in Video.app.
    For your Apple TV, if it is a 2nd gen ATV or later then you can turn on Home Sharing under Computers in the main screen.  For the 1st gen ATV, you can either share or pair with iTunes.
    If you want to physically have files (this is syncing), then you can sync your devices to the machine you want to sync with.
    With respect to FaceTime, if you want to use FaceTime on your phone with someone but separately on your iPad then you can associate your phone number to FT on your phone and on your iPad, you can use your Apple ID for FaceTime.  That way, if people want to FT on your phone, they should use the phone number to FT.  For iPad, people should enter your Apple ID when doing FT.

  • Can I use two different devices with different apple ID for backing up data on one machine without losing any data that was backed up with one device earlier?

    Can I use two different devices with different apple ID for backing up data on one machine without losing any data that was backed up with one device earlier?

    The link is to a discussion started on 12/18 in the FiOS Internet forum.  Here's the link I get now, however it is different than the link I pulled a few hours ago.  If this system changes the link again, it may not work.
    http://forums.verizon.com/t5/FiOS-Internet/Frustration-and-just-confused-with-internet-help-please/t...
    You can also look for the topic, "frustration and just confused" in the FiOS Internet forum.
    Here's a link that is in the thread that gives more detail.
    https://secure.dslreports.com/faq/15984
    Good Luck!
    P.S.  "Copper Contributor" is my "rank."  gs0b is my user name.
    If a forum member gives an answer you like, give them the Kudos they deserve. If a member gives you the answer to your question, mark the answer as Accepted Solution so others can see the solution to the problem.

  • Need help to sync two iphones to one computer with one user. Want the same library but both phones have different contact lists.

    There are two iphones in the family. We want to share the same music but separate pictures, contacts and apps. Do I have to create user accounts on the computer and different libraries?

    check out method one from this support article -> How to use multiple iPods, iPads, or iPhones with one computer

Maybe you are looking for