Difficulty detecting SATA disk, adding a second SATA disk, memory conflict, etc

I resolved the SATA problem in the middle of writing this post, but for others’ benefit in the future, I am still describing it here. But there are still some unresolved problems.
========================================================
I have an Intel P4 2.4 GHz CPU.
My MSI motherboard has the words 865PE Neon 2P on it.
BIOS is AmiBIOS 3.31a.
I cannot tell what display card I have. I do not see any brand printed on the card.
I have an (internal) 37 GB IDE hard disk (I cannot see the brand and I am too lazy to un-mount it) as the C drive.
About 3 years ago I added another internal disk, 150GB Western Digital WD 1600, SATA as the E drive.
I have a copy of Windows XP Pro SP2 on each of these two hard drives but I always boot on C.
I also have 2 DVD drives (Drives D and G) and 6 (2 at the side and 4 at the back) USB ports.
A shop installed everything for me and things have been well. I did not record the BIOS settings so I do not know how it was set up. My nightmare started about 2 weeks ago when my PC suddenly did not detect E, i.e. the SATA drive. I had not done anything to the BIOS setting or otherwise, so I have no idea why the E drive suddenly disappeared.
At that time, the Standard CMOS Features in the BIOS setting was:
Primary IDE Master - Not Installed
Primary IDE Slave - IC35L060AVV207-0
Secondary IDE Master - Pioneer DVD ROM
Secondary IDE Slave - Lite On DVD ROM
Third IDE Master - Not Installed
Third IDE Slave - Not Installed
Fourth IDE Master - Not Installed
Fourth IDE Slave - Not Installed
I tried many things and finally bought a hard disk enclosure and put that SATA in it and connect it to one of the USB ports. It works.
This morning I stumbled on this article "Motherboard can't detect SATA hard disk" at http://forum.msi.com.tw/index.php?topic=119738.0 and also “Q: How to enable both SATA and PATA? “ on “NEO Boards Unofficial FAQ rev 4/05/2004 - two lights on "P" series” at https://forum-en.msi.com/index.php?topic=21469.0 taking about the On-Chip IDE Configuration section of the BIOS menu and I decided to give it a try, so that I can get rid of that hard disk enclosure.
It works, kind of. I saw that it was set to Legacy Mode, P-ATA Only, SATA Keep Enabled=No, PATA Keep Enabled=No, PATA Channel Selection=Both, Combined Mode Option=PATA 1st Channel, SATA Ports Definition= P0-3rd/P1-4th. So following the advice on the article and the FAQ, I reset it to Legacy Mode, P-ATA + S-ATA, SATA Keep Enabled=No, PATA Keep Enabled=No, PATA Channel Selection=Both, Combined Mode Option=PATA 1st Channel, SATA Ports Definition= P0-Master/P1-Slave. Now my PC could detect the SATA drive and set it as the D drive (and the IDE remained as Drive C) but my two DVD ROMs disappeared. The Standard CMOS Features in the BIOS setting was:
Primary IDE Slave - IC35L060AVV207-0
Secondary IDE Master - WDC WD1600JD-00HBB
The rest is Not Installed.
So, I (only) changed Combined Mode Option to SATA 1st Channel. So apparently my PC now booted using the WinXP copy on the SATA disk (recall that I have WinXP on both hard disks). And now the SATA disk is C, and both DVD ROMs are visible. My IDE disk disappeared.
Now I went back to the BIOS menu and switched back to PATA 1st Channel, reset it back to P-ATA Only, and changed SATA Keep Enabled=Yes. Voila. Now I can see my IDE disk as Drive C, SATA disk as Drive D, the two DVD ROMs as Drives E and G. Everything looks fine except that some of the start-up programs no longer start up apparently because their paths used to be E:\.... but now the disk they are on was renamed from E to D so the operating system cannot locate them. And the Standard CMOS Features menu reads:
Primary IDE Master - Not Installed
Primary IDE Slave - IC35L060AVV207-0
Secondary IDE Master - Pioneer DVD ROM
Secondary IDE Slave - Lite On DVD ROM
Third IDE Master - Not Installed
Third IDE Slave - Not Installed
Fourth IDE Master - WDC WD1600JD-00HBB
Fourth IDE Slave - Not Installed
Problem 1 (the main problem): Difficulty detecting SATA disk – Resolved. If anyone is kind enough, maybe you can tell me and others why suddenly the BIOS setting was changed by itself causing all these problems, and why “P-ATA Only, SATA Keep Enabled=Yes” works but “P-ATA + S-ATA, SATA Keep Enabled=No” does not. Should I now tweak the Windows registry to change the drive letter of the SATA disk from D to E?
Problem 2: I just bought an internal Hitachi Deskstar 640GB SATA disk. And I have a vacant orange SATA connector on my mobo. Can I add it together with the existing 2? Would it be set up as Third IDE Master, Fourth IDE Slave, or something else?
Problem 3: I used to have a Samsung DDR PC2700 512MB memory module and during the last week I added a Corsair DDR PC3200 1GB memory module, both on the green slots (not the purple slots). It caused my PC to freeze (keyboard and mouse not responsive) every now and then. So I pulled out the Samsung one and it has been working fine. Some said one has to use memory from the same manufacturer with the same size and same everything. The sticky thread titled “NEO Boards Unofficial FAQ rev 4/05/2004 - two lights on "P" series” in this forum has a question “I have this RAM xxxx but it does not work with my board. Can MSI update the BIOS to fix this?” and the answer points to a Product Info page and I don’t know where that is. Any advice on how to make both work together? Can I use the purple slots?
Problem 4: The “usable” space on my Dell M991 CRT monitor has shrunk. That is, the black areas on both sides, mostly RHS, have intermittently enlarged. It only happened in these 2 weeks. I tried Control Panel – Display – Settings – Advanced – Displays – Adjustments to no avail. I don’t have another monitor to try in order to test whether it has to do with the CRT. Just in case you happen to know anything, please jot a line.
Problem 5: Some of my USB ports do not work or only work intermittently. For example I plugged in my wireless adaptor into one of them and it sometimes would say “USB Device Not Recognized”.

Quote
If anyone is kind enough, maybe you can tell me and others why suddenly the BIOS setting was changed by itself causing all these problems, and why “P-ATA Only, SATA Keep Enabled=Yes” works but “P-ATA + S-ATA, SATA Keep Enabled=No” does not.
Maybe your CMOS Battery is running low and it is time to replace it.
Quote
Should I now tweak the Windows registry to change the drive letter of the SATA disk from D to E?
Try to change drive letters via the Windows Drive Manager:
http://www.mvps.org/marksxp/WindowsXP/driveltr.php
Quote
Problem 2: I just bought an internal Hitachi Deskstar 640GB SATA disk. And I have a vacant orange SATA connector on my mobo. Can I add it together with the existing 2?
If it is a SATA-II Drive, you will probably have to force it into SATA-I Compatibility mode first (check the hard drive user manual for jumper settings or firmware switches).
Quote
I used to have a Samsung DDR PC2700 512MB memory module and during the last week I added a Corsair DDR PC3200 1GB memory module, both on the green slots (not the purple slots). It caused my PC to freeze (keyboard and mouse not responsive) every now and then. So I pulled out the Samsung one and it has been working fine. Some said one has to use memory from the same manufacturer with the same size and same everything.
Exactly. Mixing different memory modules causes problems in many cases because the exact same settings will apply to both modules at the same time. What works for the one module may not work so well for the other one.
Quote
Just in case you happen to know anything, please jot a line.
That is either related to the monitor itself or to the video card. It may also be related to a problem with the driver or improper screen resolution settings.
Quote
Problem 5: Some of my USB ports do not work or only work intermittently. For example I plugged in my wireless adaptor into one of them and it sometimes would say “USB Device Not Recognized”.
What ports? Front Panel or Back Panel?

Similar Messages

Adding a Second SATA Hard Drive

Hi PPL,
I have a K7N2 Delta - ILSR mobo and I want to add a second serial ATA hard drive to my board (identical to the drive already fitted) and I just wondered if there was anything I should beware of when setting up the array (using promise 376/378 driver) as I don't want to screw up and lose data on the original drive.
Any ideas???
Cheers,
Jon.

If you are going to be RAIDing them, you will have to reinstall Windows. You could back up any stuff you need onto another HD...Then set-up, make and format the array...After that you could move your stuff back over to the array from the back-up HD...I don't think there is a way to build an array and not reformat the drives, thus losing all data on them...
As far as setting up the array, check your manual for the proper install methods...There are also some pretty useful guides floating around the forums here. Good Luck.

[SOLVED] Problem with second SATA drive

My laptop has two hard drive bays, and just recently I added a second SATA drive (moved it from my old laptop) to the extra bay.
Now, anytime the second hard drive /dev/sdb has any heavy disk activity, it appears to cause a shutdown of the SATA port for the first drive (/dev/sda)! Though the second drive is still fine, and I can still write to it until the system crashes from the root drive (on /dev/sda) being shutdown.
If I don't mount and use the second drive, the first drive works just fine, and I can pound it with traffic without issue.
I can reproduce this problem by copying large amounts of data to drive 2.
This is when I get in my dmesg when the first SATA drive shuts down:
[ 3013.249525] ata1.00: exception Emask 0x0 SAct 0x7ff SErr 0x0 action 0x6 frozen
[ 3013.249532] ata1.00: failed command: READ FPDMA QUEUED
[ 3013.249539] ata1.00: cmd 60/08:00:78:b8:ba/00:00:24:00:00/40 tag 0 ncq 4096 in
[ 3013.249539] res 40/00:00:00:4f:c2/00:00:00:00:00/40 Emask 0x4 (timeout)
[ 3013.249543] ata1.00: status: { DRDY }
[ 3013.249545] ata1.00: failed command: WRITE FPDMA QUEUED
[ 3013.249559] ata1.00: cmd 61/08:08:b8:60:7b/00:00:29:00:00/40 tag 1 ncq 4096 out
[ 3013.249559] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 3013.249562] ata1.00: status: { DRDY }
[ 3013.249564] ata1.00: failed command: WRITE FPDMA QUEUED
[ 3013.249568] ata1.00: cmd 61/08:10:c0:60:7b/00:00:29:00:00/40 tag 2 ncq 4096 out
[ 3013.249568] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 3013.249570] ata1.00: status: { DRDY }
[ 3013.249572] ata1.00: failed command: WRITE FPDMA QUEUED
[ 3013.249576] ata1.00: cmd 61/08:18:c8:60:7b/00:00:29:00:00/40 tag 3 ncq 4096 out
[ 3013.249576] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 3013.249578] ata1.00: status: { DRDY }
[ 3013.249580] ata1.00: failed command: WRITE FPDMA QUEUED
[ 3013.249585] ata1.00: cmd 61/08:20:48:12:d7/00:00:18:00:00/40 tag 4 ncq 4096 out
[ 3013.249585] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 3013.249587] ata1.00: status: { DRDY }
[ 3013.249589] ata1.00: failed command: WRITE FPDMA QUEUED
[ 3013.249593] ata1.00: cmd 61/08:28:28:63:38/00:00:19:00:00/40 tag 5 ncq 4096 out
[ 3013.249593] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 3013.249595] ata1.00: status: { DRDY }
[ 3013.249597] ata1.00: failed command: WRITE FPDMA QUEUED
[ 3013.249601] ata1.00: cmd 61/08:30:28:6f:38/00:00:19:00:00/40 tag 6 ncq 4096 out
[ 3013.249601] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 3013.249603] ata1.00: status: { DRDY }
[ 3013.249605] ata1.00: failed command: WRITE FPDMA QUEUED
[ 3013.249609] ata1.00: cmd 61/08:38:28:98:ae/00:00:25:00:00/40 tag 7 ncq 4096 out
[ 3013.249609] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 3013.249611] ata1.00: status: { DRDY }
[ 3013.249613] ata1.00: failed command: WRITE FPDMA QUEUED
[ 3013.249617] ata1.00: cmd 61/08:40:d8:79:3b/00:00:25:00:00/40 tag 8 ncq 4096 out
[ 3013.249617] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 3013.249619] ata1.00: status: { DRDY }
[ 3013.249621] ata1.00: failed command: WRITE FPDMA QUEUED
[ 3013.249625] ata1.00: cmd 61/08:48:08:98:b6/00:00:18:00:00/40 tag 9 ncq 4096 out
[ 3013.249625] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 3013.249627] ata1.00: status: { DRDY }
[ 3013.249629] ata1.00: failed command: WRITE FPDMA QUEUED
[ 3013.249633] ata1.00: cmd 61/08:50:10:98:36/00:00:19:00:00/40 tag 10 ncq 4096 out
[ 3013.249633] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 3013.249636] ata1.00: status: { DRDY }
[ 3013.249640] ata1: hard resetting link
[ 3013.575549] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 3013.576784] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
[ 3013.578334] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
[ 3013.578588] ata1.00: configured for UDMA/133
[ 3013.592223] ata1.00: device reported invalid CHS sector 0
[ 3013.592233] ata1.00: device reported invalid CHS sector 0
[ 3013.592238] ata1.00: device reported invalid CHS sector 0
[ 3013.592242] ata1.00: device reported invalid CHS sector 0
[ 3013.592246] ata1.00: device reported invalid CHS sector 0
[ 3013.592250] ata1.00: device reported invalid CHS sector 0
[ 3013.592254] ata1.00: device reported invalid CHS sector 0
[ 3013.592258] ata1.00: device reported invalid CHS sector 0
[ 3013.592263] ata1.00: device reported invalid CHS sector 0
[ 3013.592267] ata1.00: device reported invalid CHS sector 0
[ 3013.592271] ata1.00: device reported invalid CHS sector 0
[ 3013.592302] sd 0:0:0:0: [sda]
[ 3013.592306] Result: hostbyte=0x00 driverbyte=0x08
[ 3013.592310] sd 0:0:0:0: [sda]
[ 3013.592313] Sense Key : 0xb [current] [descriptor]
[ 3013.592320] Descriptor sense data with sense descriptors (in hex):
[ 3013.592323] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3013.592342] 00 00 00 00
[ 3013.592351] sd 0:0:0:0: [sda]
[ 3013.592353] ASC=0x0 ASCQ=0x0
[ 3013.592358] sd 0:0:0:0: [sda] CDB:
[ 3013.592361] cdb[0]=0x28: 28 00 24 ba b8 78 00 00 08 00
[ 3013.592376] end_request: I/O error, dev sda, sector 616216696
[ 3013.592414] sd 0:0:0:0: [sda]
[ 3013.592417] Result: hostbyte=0x00 driverbyte=0x08
[ 3013.592421] sd 0:0:0:0: [sda]
[ 3013.592423] Sense Key : 0xb [current] [descriptor]
[ 3013.592428] Descriptor sense data with sense descriptors (in hex):
[ 3013.592431] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3013.592449] 00 00 00 00
[ 3013.592458] sd 0:0:0:0: [sda]
[ 3013.592460] ASC=0x0 ASCQ=0x0
[ 3013.592465] sd 0:0:0:0: [sda] CDB:
[ 3013.592467] cdb[0]=0x2a: 2a 00 29 7b 60 b8 00 00 08 00
[ 3013.592482] end_request: I/O error, dev sda, sector 695951544
[ 3013.592505] sd 0:0:0:0: [sda]
[ 3013.592508] Result: hostbyte=0x00 driverbyte=0x08
[ 3013.592512] sd 0:0:0:0: [sda]
[ 3013.592514] Sense Key : 0xb [current] [descriptor]
[ 3013.592519] Descriptor sense data with sense descriptors (in hex):
[ 3013.592522] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3013.592540] 00 00 00 00
[ 3013.592549] sd 0:0:0:0: [sda]
[ 3013.592551] ASC=0x0 ASCQ=0x0
[ 3013.592556] sd 0:0:0:0: [sda] CDB:
[ 3013.592558] cdb[0]=0x2a: 2a 00 29 7b 60 c0 00 00 08 00
[ 3013.592572] end_request: I/O error, dev sda, sector 695951552
[ 3013.592583] sd 0:0:0:0: [sda]
[ 3013.592586] Result: hostbyte=0x00 driverbyte=0x08
[ 3013.592589] sd 0:0:0:0: [sda]
[ 3013.592592] Sense Key : 0xb [current] [descriptor]
[ 3013.592597] Descriptor sense data with sense descriptors (in hex):
[ 3013.592599] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3013.592618] 00 00 00 00
[ 3013.592626] sd 0:0:0:0: [sda]
[ 3013.592628] ASC=0x0 ASCQ=0x0
[ 3013.592632] sd 0:0:0:0: [sda] CDB:
[ 3013.592635] cdb[0]=0x2a: 2a 00 29 7b 60 c8 00 00 08 00
[ 3013.592649] end_request: I/O error, dev sda, sector 695951560
[ 3013.592665] sd 0:0:0:0: [sda]
[ 3013.592668] Result: hostbyte=0x00 driverbyte=0x08
[ 3013.592671] sd 0:0:0:0: [sda]
[ 3013.592673] Sense Key : 0xb [current] [descriptor]
[ 3013.592678] Descriptor sense data with sense descriptors (in hex):
[ 3013.592684] Aborting journal on device dm-0-8.
[ 3013.592701] EXT4-fs error (device dm-0) in ext4_reserve_inode_write:4476: Journal has aborted
[ 3013.592687] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3013.592723] 00 00 00 00
[ 3013.592729] sd 0:0:0:0: [sda]
[ 3013.592730] ASC=0x0 ASCQ=0x0
[ 3013.592733] sd 0:0:0:0: [sda] CDB:
[ 3013.592735] cdb[0]=0x2a: 2a 00 18 d7 12 48 00 00 08 00
[ 3013.592744] end_request: I/O error, dev sda, sector 416748104
[ 3013.592752] Buffer I/O error on device dm-0, logical block 266057
[ 3013.592760] EXT4-fs warning (device dm-0): ext4_end_bio:250: I/O error writing to inode 5902184 (offset 258048 size 4096 starting block 266057)
[ 3013.592766] sd 0:0:0:0: [sda]
[ 3013.592768] Result: hostbyte=0x00 driverbyte=0x08
[ 3013.592771] sd 0:0:0:0: [sda]
[ 3013.592772] Sense Key : 0xb [current] [descriptor]
[ 3013.592776] Descriptor sense data with sense descriptors (in hex):
[ 3013.592778] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3013.592790] 00 00 00 00
[ 3013.592795] sd 0:0:0:0: [sda]
[ 3013.592797] ASC=0x0 ASCQ=0x0
[ 3013.592800] sd 0:0:0:0: [sda] CDB:
[ 3013.592801] cdb[0]=0x2a: 2a 00 19 38 63 28 00 00 08 00
[ 3013.592811] end_request: I/O error, dev sda, sector 423125800
[ 3013.592817] Buffer I/O error on device dm-0, logical block 1063269
[ 3013.592822] EXT4-fs warning (device dm-0): ext4_end_bio:250: I/O error writing to inode 5898577 (offset 970752 size 4096 starting block 1063269)
[ 3013.592842] sd 0:0:0:0: [sda]
[ 3013.592845] Result: hostbyte=0x00 driverbyte=0x08
[ 3013.592849] sd 0:0:0:0: [sda]
[ 3013.592851] Sense Key : 0xb [current] [descriptor]
[ 3013.592856] Descriptor sense data with sense descriptors (in hex):
[ 3013.592859] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3013.592877] 00 00 00 00
[ 3013.592885] sd 0:0:0:0: [sda]
[ 3013.592887] ASC=0x0 ASCQ=0x0
[ 3013.592892] sd 0:0:0:0: [sda] CDB:
[ 3013.592894] cdb[0]=0x2a: 2a 00 19 38 6f 28 00 00 08 00
[ 3013.592908] end_request: I/O error, dev sda, sector 423128872
[ 3013.592915] Buffer I/O error on device dm-0, logical block 1063653
[ 3013.592922] EXT4-fs warning (device dm-0): ext4_end_bio:250: I/O error writing to inode 5902187 (offset 1171456 size 4096 starting block 1063653)
[ 3013.592931] sd 0:0:0:0: [sda]
[ 3013.592934] Result: hostbyte=0x00 driverbyte=0x08
[ 3013.592937] sd 0:0:0:0: [sda]
[ 3013.592940] Sense Key : 0xb [current] [descriptor]
[ 3013.592945] Descriptor sense data with sense descriptors (in hex):
[ 3013.592947] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3013.592966] 00 00 00 00
[ 3013.592974] sd 0:0:0:0: [sda]
[ 3013.592976] ASC=0x0 ASCQ=0x0
[ 3013.592980] sd 0:0:0:0: [sda] CDB:
[ 3013.592983] cdb[0]=0x2a: 2a 00 25 ae 98 28 00 00 08 00
[ 3013.592997] end_request: I/O error, dev sda, sector 632199208
[ 3013.593006] Buffer I/O error on device dm-0, logical block 27197445
[ 3013.593018] EXT4-fs warning (device dm-0): ext4_end_bio:250: I/O error writing to inode 6425165 (offset 151552 size 4096 starting block 27197445)
[ 3013.593028] sd 0:0:0:0: [sda]
[ 3013.593031] Result: hostbyte=0x00 driverbyte=0x08
[ 3013.593034] sd 0:0:0:0: [sda]
[ 3013.593037] Sense Key : 0xb [current] [descriptor]
[ 3013.593042] Descriptor sense data with sense descriptors (in hex):
[ 3013.593045] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3013.593063] 00 00 00 00
[ 3013.593071] sd 0:0:0:0: [sda]
[ 3013.593073] ASC=0x0 ASCQ=0x0
[ 3013.593078] sd 0:0:0:0: [sda] CDB:
[ 3013.593085] EXT4-fs error (device dm-0) in ext4_reserve_inode_write:4476: Journal has aborted
[ 3013.593089] cdb[0]=0x2a: 2a 00 25 3b 79 d8 00 00 08 00
[ 3013.593104] end_request: I/O error, dev sda, sector 624654808
[ 3013.593111] Buffer I/O error on device dm-0, logical block 26254395
[ 3013.593115] lost page write due to I/O error on dm-0
[ 3013.593126] sd 0:0:0:0: [sda]
[ 3013.593129] Result: hostbyte=0x00 driverbyte=0x08
[ 3013.593132] sd 0:0:0:0: [sda]
[ 3013.593135] Sense Key : 0xb [current] [descriptor]
[ 3013.593140] Descriptor sense data with sense descriptors (in hex):
[ 3013.593142] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3013.593161] 00 00 00 00
[ 3013.593169] sd 0:0:0:0: [sda]
[ 3013.593171] ASC=0x0 ASCQ=0x0
[ 3013.593175] sd 0:0:0:0: [sda] CDB:
[ 3013.593178] cdb[0]=0x2a: 2a 00 18 b6 98 08 00 00 08 00
[ 3013.593192] end_request: I/O error, dev sda, sector 414619656
[ 3013.593198] Buffer I/O error on device dm-0, logical block 1
[ 3013.593201] lost page write due to I/O error on dm-0
[ 3013.593211] sd 0:0:0:0: [sda]
[ 3013.593213] Result: hostbyte=0x00 driverbyte=0x08
[ 3013.593217] sd 0:0:0:0: [sda]
[ 3013.593219] Sense Key : 0xb [current] [descriptor]
[ 3013.593224] Descriptor sense data with sense descriptors (in hex):
[ 3013.593227] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3013.593245] 00 00 00 00
[ 3013.593253] sd 0:0:0:0: [sda]
[ 3013.593256] ASC=0x0 ASCQ=0x0
[ 3013.593260] sd 0:0:0:0: [sda] CDB:
[ 3013.593262] cdb[0]=0x2a: 2a 00 19 36 98 10 00 00 08 00
[ 3013.593277] end_request: I/O error, dev sda, sector 423008272
[ 3013.593283] Buffer I/O error on device dm-0, logical block 1048578
[ 3013.593286] lost page write due to I/O error on dm-0
[ 3013.593298] ata1: EH complete
[ 3013.595707] EXT4-fs error (device dm-0) in ext4_dirty_inode:4603: Journal has aborted
[ 3013.596581] EXT4-fs error (device dm-0): ext4_journal_start_sb:370: Detected aborted journal
[ 3013.596591] EXT4-fs (dm-0): Remounting filesystem read-only
[ 3020.421558] journal commit I/O error
[ 3020.421570] journal commit I/O error
[ 3020.421574] journal commit I/O error
[ 3020.421578] journal commit I/O error
[ 3020.421581] journal commit I/O error
[ 3147.052191] ata1.00: exception Emask 0x0 SAct 0xf SErr 0x0 action 0x6 frozen
[ 3147.052197] ata1.00: failed command: READ FPDMA QUEUED
[ 3147.052209] ata1.00: cmd 60/50:00:d0:48:99/00:00:1c:00:00/40 tag 0 ncq 40960 in
[ 3147.052209] res 40/00:00:00:4f:c2/00:00:00:00:00/40 Emask 0x4 (timeout)
[ 3147.052212] ata1.00: status: { DRDY }
[ 3147.052213] ata1.00: failed command: READ FPDMA QUEUED
[ 3147.052218] ata1.00: cmd 60/18:08:28:49:99/00:00:1c:00:00/40 tag 1 ncq 12288 in
[ 3147.052218] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 3147.052220] ata1.00: status: { DRDY }
[ 3147.052221] ata1.00: failed command: READ FPDMA QUEUED
[ 3147.052226] ata1.00: cmd 60/88:10:48:49:99/00:00:1c:00:00/40 tag 2 ncq 69632 in
[ 3147.052226] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 3147.052228] ata1.00: status: { DRDY }
[ 3147.052229] ata1.00: failed command: READ FPDMA QUEUED
[ 3147.052234] ata1.00: cmd 60/20:18:00:a4:ba/00:00:24:00:00/40 tag 3 ncq 16384 in
[ 3147.052234] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 3147.052236] ata1.00: status: { DRDY }
[ 3147.052239] ata1: hard resetting link
[ 3147.378368] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 3148.066853] ata1.00: ACPI cmd ef/5a:00:00:00:00:a0 (SET FEATURES) succeeded
[ 3148.069139] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
[ 3148.069393] ata1.00: configured for UDMA/133
[ 3148.080059] ata1.00: device reported invalid CHS sector 0
[ 3148.080066] ata1.00: device reported invalid CHS sector 0
[ 3148.080071] ata1.00: device reported invalid CHS sector 0
[ 3148.080075] ata1.00: device reported invalid CHS sector 0
[ 3148.080112] sd 0:0:0:0: [sda]
[ 3148.080114] Result: hostbyte=0x00 driverbyte=0x08
[ 3148.080117] sd 0:0:0:0: [sda]
[ 3148.080118] Sense Key : 0xb [current] [descriptor]
[ 3148.080123] Descriptor sense data with sense descriptors (in hex):
[ 3148.080125] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3148.080136] 00 00 00 00
[ 3148.080140] sd 0:0:0:0: [sda]
[ 3148.080142] ASC=0x0 ASCQ=0x0
[ 3148.080145] sd 0:0:0:0: [sda] CDB:
[ 3148.080146] cdb[0]=0x28: 28 00 1c 99 48 d0 00 00 50 00
[ 3148.080156] end_request: I/O error, dev sda, sector 479807696
[ 3148.080170] sd 0:0:0:0: [sda]
[ 3148.080171] Result: hostbyte=0x00 driverbyte=0x08
[ 3148.080173] sd 0:0:0:0: [sda]
[ 3148.080175] Sense Key : 0xb [current] [descriptor]
[ 3148.080178] Descriptor sense data with sense descriptors (in hex):
[ 3148.080180] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3148.080190] 00 00 00 00
[ 3148.080195] sd 0:0:0:0: [sda]
[ 3148.080196] ASC=0x0 ASCQ=0x0
[ 3148.080199] sd 0:0:0:0: [sda] CDB:
[ 3148.080200] cdb[0]=0x28: 28 00 1c 99 49 28 00 00 18 00
[ 3148.080209] end_request: I/O error, dev sda, sector 479807784
[ 3148.080216] sd 0:0:0:0: [sda]
[ 3148.080218] Result: hostbyte=0x00 driverbyte=0x08
[ 3148.080220] sd 0:0:0:0: [sda]
[ 3148.080221] Sense Key : 0xb [current] [descriptor]
[ 3148.080224] Descriptor sense data with sense descriptors (in hex):
[ 3148.080225] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3148.080236] 00 00 00 00
[ 3148.080241] sd 0:0:0:0: [sda]
[ 3148.080242] ASC=0x0 ASCQ=0x0
[ 3148.080245] sd 0:0:0:0: [sda] CDB:
[ 3148.080246] cdb[0]=0x28: 28 00 1c 99 49 48 00 00 88 00
[ 3148.080254] end_request: I/O error, dev sda, sector 479807816
[ 3148.080267] sd 0:0:0:0: [sda]
[ 3148.080268] Result: hostbyte=0x00 driverbyte=0x08
[ 3148.080270] sd 0:0:0:0: [sda]
[ 3148.080272] Sense Key : 0xb [current] [descriptor]
[ 3148.080274] Descriptor sense data with sense descriptors (in hex):
[ 3148.080276] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 3148.080287] 00 00 00 00
[ 3148.080291] sd 0:0:0:0: [sda]
[ 3148.080293] ASC=0x0 ASCQ=0x0
[ 3148.080295] sd 0:0:0:0: [sda] CDB:
[ 3148.080296] cdb[0]=0x28: 28 00 24 ba a4 00 00 00 20 00
[ 3148.080305] end_request: I/O error, dev sda, sector 616211456
[ 3148.080315] ata1: EH complete
I have experimented, and found that if I turn off NCQ on the kernel command line in my bootloader (libata.force=noncq), that it takes longer before the problem occurs. Though, if I write enough to the second drive, it does still happen after a while, just greatly reduced its chances of happening.
Is it possible that the old drive (sdb) is causing the problem? I noticed that it is much noisier than I remember when the drive head moves around.
Another curiosity while I was trying to duplicate the problem:
- I start a large file copy from sda -> sdb
- At the same time in another terminal, I do "find / -print"
- When I hear the drive 2 head moving, it pauses the output of the "find" command.
Every time I hear the head move, I see the find output pause. Its almost like the drive seek on drive 2 causes the whole Sata controller to pause while the head moves. Very odd!
Anyone have any ideas? I think the next thing I will try is borrow a drive from another machine, and do the big write to it to see if I get the same results.
If it is of any help, here is some more info on the laptop:
lspci:
00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09)
00:01.0 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09)
00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04)
00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05)
00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05)
00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5)
00:1c.2 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 3 (rev b5)
00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5)
00:1c.5 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 6 (rev b5)
00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05)
00:1f.0 ISA bridge: Intel Corporation HM67 Express Chipset Family LPC Controller (rev 05)
00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05)
00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05)
01:00.0 VGA compatible controller: NVIDIA Corporation Device 1251 (rev a1)
01:00.1 Audio device: NVIDIA Corporation GF116 High Definition Audio Controller (rev a1)
07:00.0 Ethernet controller: Atheros Communications Inc. AR8151 v2.0 Gigabit Ethernet (rev c0)
0d:00.0 Network controller: Intel Corporation Centrino Advanced-N + WiMAX 6250 (rev 5e)
13:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTS5209 PCI Express Card Reader (rev 01)
13:00.1 SD Host controller: Realtek Semiconductor Co., Ltd. RTS5209 PCI Express Card Reader (rev 01)
19:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04)
cat /proc/interrupts:
CPU0 CPU1 CPU2 CPU3 CPU4 CPU5 CPU6 CPU7
0: 50 0 0 0 0 0 0 0 IO-APIC-edge timer
1: 958 0 0 0 0 0 0 0 IO-APIC-edge i8042
8: 1 0 0 0 0 0 0 0 IO-APIC-edge rtc0
9: 1675 0 0 0 0 0 0 0 IO-APIC-fasteoi acpi
12: 12257 0 0 0 0 0 0 0 IO-APIC-edge i8042
16: 24769 0 0 0 0 0 0 0 IO-APIC-fasteoi ehci_hcd:usb1, mmc0, nvidia
17: 142 0 0 0 0 0 0 0 IO-APIC-fasteoi snd_hda_intel
19: 0 0 0 0 0 0 0 0 IO-APIC-fasteoi rts_pstor
23: 1937 0 0 0 0 0 0 0 IO-APIC-fasteoi ehci_hcd:usb4
41: 1 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd
42: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd
43: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd
44: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd
45: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd
46: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd
47: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd
48: 0 0 0 0 0 0 0 0 PCI-MSI-edge xhci_hcd
49: 19406 0 0 0 0 0 0 0 PCI-MSI-edge iwlwifi
50: 36099 0 0 0 0 0 0 0 PCI-MSI-edge ahci
51: 14 0 0 0 0 0 0 0 PCI-MSI-edge mei
52: 386378 0 0 0 0 0 0 0 PCI-MSI-edge snd_hda_intel
53: 56803 0 0 0 0 0 0 0 PCI-MSI-edge eth0
NMI: 34 5 19 5 18 4 13 4 Non-maskable interrupts
LOC: 77964 17705 161241 14302 187823 16150 56845 12750 Local timer interrupts
SPU: 0 0 0 0 0 0 0 0 Spurious interrupts
PMI: 34 5 19 5 18 4 13 4 Performance monitoring interrupts
IWI: 0 0 0 0 0 0 0 0 IRQ work interrupts
RTR: 7 0 0 0 0 0 0 0 APIC ICR read retries
RES: 13721 7023 304 110 175 110 213 123 Rescheduling interrupts
CAL: 6941 7677 2774 7670 5804 7568 7655 7673 Function call interrupts
TLB: 366 545 268 179 310 272 212 166 TLB shootdowns
TRM: 0 0 0 0 0 0 0 0 Thermal event interrupts
THR: 0 0 0 0 0 0 0 0 Threshold APIC interrupts
MCE: 0 0 0 0 0 0 0 0 Machine check exceptions
MCP: 29 29 29 29 29 29 29 29 Machine check polls
ERR: 0
MIS: 0
smartctl --all /dev/sda
smartctl 5.43 2012-06-30 r3573 [x86_64-linux-3.5.3-1-ARCH] (local build)
Copyright (C) 2002-12 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Device Model: ST9500423AS
Serial Number: 5WS354LM
LU WWN Device Id: 5 000c50 044bb741b
Firmware Version: 0005DEM1
User Capacity: 500,107,862,016 bytes [500 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 4
Local Time is: Thu Sep 13 15:26:14 2012 CDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x73) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 105) minutes.
Conveyance self-test routine
recommended polling time: ( 3) minutes.
SCT capabilities: (0x303f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 113 099 006 Pre-fail Always - 54715920
3 Spin_Up_Time 0x0003 098 098 085 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 099 099 020 Old_age Always - 1114
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 069 060 030 Pre-fail Always - 10214892
9 Power_On_Hours 0x0032 098 098 000 Old_age Always - 2030
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 559
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 098 000 Old_age Always - 8590065667
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 053 049 045 Old_age Always - 47 (Min/Max 47/51)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 17
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 871
193 Load_Cycle_Count 0x0032 039 039 000 Old_age Always - 122293
194 Temperature_Celsius 0x0022 047 051 000 Old_age Always - 47 (0 17 0 0 0)
195 Hardware_ECC_Recovered 0x001a 113 099 000 Old_age Always - 54715920
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 67229123085518
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 1947733828
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 2798982459
254 Free_Fall_Sensor 0x0032 001 001 000 Old_age Always - 899
SMART Error Log Version: 1
ATA Error Count: 8 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 8 occurred at disk power-on lifetime: 2017 hours (84 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
04 71 09 a9 00 80 e0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
a1 00 00 00 00 00 a0 00 05:21:04.438 IDENTIFY PACKET DEVICE
ec 00 00 00 00 00 a0 00 05:21:04.438 IDENTIFY DEVICE
00 00 00 00 00 00 00 ff 05:21:04.124 NOP [Abort queued commands]
a1 00 00 00 00 00 a0 00 05:20:59.118 IDENTIFY PACKET DEVICE
ec 00 00 00 00 00 a0 00 05:20:59.118 IDENTIFY DEVICE
Error 7 occurred at disk power-on lifetime: 2017 hours (84 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
04 71 09 a9 00 80 e0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
ec 00 00 00 00 00 a0 00 05:21:04.438 IDENTIFY DEVICE
00 00 00 00 00 00 00 ff 05:21:04.124 NOP [Abort queued commands]
a1 00 00 00 00 00 a0 00 05:20:59.118 IDENTIFY PACKET DEVICE
ec 00 00 00 00 00 a0 00 05:20:59.118 IDENTIFY DEVICE
00 00 00 00 00 00 00 ff 05:20:58.805 NOP [Abort queued commands]
Error 6 occurred at disk power-on lifetime: 2017 hours (84 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
04 71 09 a9 00 80 e0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
a1 00 00 00 00 00 a0 00 05:20:59.118 IDENTIFY PACKET DEVICE
ec 00 00 00 00 00 a0 00 05:20:59.118 IDENTIFY DEVICE
00 00 00 00 00 00 00 ff 05:20:58.805 NOP [Abort queued commands]
a1 00 00 00 00 00 a0 00 05:20:58.761 IDENTIFY PACKET DEVICE
ec 00 00 00 00 00 a0 00 05:20:58.725 IDENTIFY DEVICE
Error 5 occurred at disk power-on lifetime: 2017 hours (84 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
04 71 09 a9 00 80 e0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
ec 00 00 00 00 00 a0 00 05:20:59.118 IDENTIFY DEVICE
00 00 00 00 00 00 00 ff 05:20:58.805 NOP [Abort queued commands]
a1 00 00 00 00 00 a0 00 05:20:58.761 IDENTIFY PACKET DEVICE
ec 00 00 00 00 00 a0 00 05:20:58.725 IDENTIFY DEVICE
2f 00 01 10 00 00 a0 00 05:20:58.724 READ LOG EXT
Error 4 occurred at disk power-on lifetime: 2017 hours (84 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
04 71 09 a9 00 80 e0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
a1 00 00 00 00 00 a0 00 05:20:58.761 IDENTIFY PACKET DEVICE
ec 00 00 00 00 00 a0 00 05:20:58.725 IDENTIFY DEVICE
2f 00 01 10 00 00 a0 00 05:20:58.724 READ LOG EXT
61 00 08 ff ff ff 4f 00 05:20:58.724 WRITE FPDMA QUEUED
61 00 08 ff ff ff 4f 00 05:20:58.724 WRITE FPDMA QUEUED
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 6 -
# 2 Short offline Aborted by host 90% 1 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
smartctl --all /dev/sdb
smartctl 5.43 2012-06-30 r3573 [x86_64-linux-3.5.3-1-ARCH] (local build)
Copyright (C) 2002-12 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Model Family: SAMSUNG SpinPoint M6
Device Model: SAMSUNG HM320JI
Serial Number: S16LJF0QB02815
LU WWN Device Id: 5 0f0000 001202815
Firmware Version: 2SS00_01
User Capacity: 320,072,933,376 bytes [320 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: ATA/ATAPI-7 T13 1532D revision 0
Local Time is: Thu Sep 13 15:27:10 2012 CDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 110) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 110) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 100 100 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0007 252 252 025 Pre-fail Always - 2562
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 810
5 Reallocated_Sector_Ct 0x0033 252 252 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x000e 252 252 051 Old_age Always - 0
8 Seek_Time_Performance 0x0024 252 252 015 Old_age Offline - 0
9 Power_On_Hours 0x0032 092 092 000 Old_age Always - 4842
10 Spin_Retry_Count 0x0032 252 252 051 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 440
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 154
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 71
194 Temperature_Celsius 0x0022 073 073 000 Old_age Always - 55 (Min/Max 17/55)
195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always - 1
196 Reallocated_Event_Count 0x0032 252 252 000 Old_age Always - 0
197 Current_Pending_Sector 0x0012 252 252 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 252 252 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0036 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x000a 100 100 000 Old_age Always - 0
201 Soft_Read_Error_Rate 0x0032 252 252 000 Old_age Always - 0
223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 534
225 Load_Cycle_Count 0x0032 077 077 000 Old_age Always - 236803
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
Note: selective self-test log revision number (0) not 1 implies that no selective self-test has ever been run
SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Last edited by johni (2012-09-16 00:46:54)

It appears my drive one really is failing. It was the first drive and not the second making the loud head seek sound. I borrowed another drive from a friend, and copied my drive one to it. No problems with the new drive in place.

[Athlon64] 'No disks detected' when installing WinXP64bit on striped SATA RAID

I've been using my RS480M2 board with a dual boot config (WinXP Pro 32bit and WinXP Pro 64bit) using a Maxtor Diamond Plus 80G SATA hard drive configured as an IDE/ATA. I set the controller as "IDE Controller" in the bios. Everything has been working just fine and I must say that I really do notice a big performance improvement on the WinXP64bit compared to the WinXP32bit.
I then purchased another Maxtor 80G SATA with the intention of setting up a SATA RAID 0 (striping) config to see if I will get more performance gain. So I changed the controller to "SATA Raid Controller" in the bios. Then I used the Sil3112A GUI (by pressing F4) to configure my 2 SATA hard drives as RAID 0. I tried installing WinXP Pro 64bit but the SATA RAID drivers I've tried just do not work. The Windows setup would indicate that there are no disks detected. I already tried the 32bit SATA RAID driver, the one at Silicon Image site, a few ones at PlanetAMD64, etc. No luck!!!
So I just installed WinXP Pro 32bit using the provided Sil3112 SATA RAID driver floppy diskette that came with my board. And it installed without any problems. All is well. So the problem is: WHERE THE HELL CAN I GET A SATA RAID DRIVER FOR WINXP64BIT???
To anyone who has the solution to my problem, kindly email the driver (or link) at [email protected]
Thanks.

Sorry for the late reply. I finally got to install Windows XP Pro 64bit onto my RS480M2-IL configured as SATA RAID 0 (striping) with 2 80G DiamondPlus SATA hard drives. The sata drive that worked is the one on this link:
http://www.planetamd64.com/index.php?showtopic=9433
Thanks a bunch to Mtalea

Second SATA Drive Read Only

Need some help:
I took my SATA Drive out of my Windows Computer (NTFS) 250GB, and put it into the second SATA bay of the G5. It had one jumper on the 3rd setting.
The G5 found it and it can read fine, but it is read only. nothing i do can erase, format, etc. Disk info says owner:no, permissions:only read, can be formatted:no, SMART Status not supported, pretty much locked. It shows up as a 232.9 GB WDC WD2500JD-00FYB0.
Any Suggestions on how to make writable/format? Is it a jumper issue?
Thanks for your help out there!

According to "http://docs.info.apple.com/article.html?artnum=75320"
"Warning: NTFS formatted drives cannot be used in a Macintosh (except as read-only with Mac OS X 10.,3 as noted above). If you attempt to use a NTFS formatted disk, upon starting up the Mac OS will prompt you to format the drive. Do not format the drive, doing so will erase the contents of the drive. If you have an NTFS formatted disk, you must use another method to transfer the data from the PC to the Macintosh".
Did you have this warning when you started up your G5 after installing the second drive ?
If yes you may have to shut down the computer, disconnect the second NTFS SATA drive, restart and shut down, reconnect and restart to reformat.
Just a suggestion.
Good Luck
Luc

Jumper Settings for Second SATA-II drive Installed Into Dual 2.0Ghz G5

I have installed a second SATA-II 500GB Maxtor drive into a brand new (purchased as re-furbished computer from Apple) dual 2.0Ghz PowerMac G5. The drive has four connector pins with a jumper slide over the last pin on the right. Before I power up the computer I want to verify the correct jumper settings. According to the Maxtor website, no jumpers are required since the "serial ATA host automatically determines the master and slave hard drive." And according to a MacSales tech (this is the vendor where I purchased the Maxtor drive) I should pull off the existing jumper. Can anyone verify if this is, in fact, the correct jumper setting (no jumpers on the connector pins) for this drive on this system?
G5 dual 2.0 Ghz Mac OS X (10.4.8)

Hello! From the Maxtor web site.
"PLEASE NOTE: Unlike standard ATA drives, Serial ATA drives DO NOT require the use of jumpers to configure the drive. Please disregard any references to jumper settings and Master, Slave and Cable Select configurations in the Maxtor Installation Guide."
I'd leave the jumper as is came when you got it. tom

Does Macbook Pro 13" early 2011 support SATA III 6,0Gbit/s ssd disks?

Can someone please tell if Macbook Pro 13" early 2011 support SATA III 6,0Gbit/s ssd disks?
If it do, I will order it today =)

See posts from MacRS4 in this thread:
http://discussions.apple.com/thread.jspa?messageID=13129019&#13129019

Second SATA HD formatting...

well i managed to update my bios successfully, again no hitches,
but the ram is still only showing up as 2 x 256 instead of 2 x 512,
even when run solo.
i cant install XP SP2 yet either because the machine is primarily for running ProTools, which isnt compatible with it yet.
might i be wise to send back the ram while i still can?
and i need advice on how to get my second SATA drive working!
i left it out til i got everything up and running with the boot drive and now want to get it going for use as my audio drive; ive hooked it up, it appears as working fine in device manager, but i cant seem to format it!
partitionmagic wont do it either. in fact, it wont do anything! i put a 40gb partition on my boot drive when installing winxp, intending to set the other 40gb of that drive up later to store games and random files on, and now i cant seem to set up even that second partition, thus my 80gb drive is only operational as 40gb! and my second 160GB drive cant be brought to life at all!
egadz the hassle!
please help!

Hi.
In the many times I am in Dublin, I've never been called a leg end.
The external drive, if its SATA, the drivers are already on C:> drive, so you should be able to see and format it, IDE just as any IDE.
The Rambiz, best run memtest86 and see if Ram is compatable with rig, and itself.
Then in Bios, change Memclock mode to limit, then memclock value to 333 or 400, some mem works at DDR333 only, try that and see if it finds the other stick. You might try Dimm3 for 2nd stick, sometimes Dimm2 is flakey with certain Ram.
Ram that gives Memtest errors at 400, often is OK at 333. You may have a flakey stick, if all errors in MT are above 512, you will know stick 2 is not compatable with stick 1, try them seperately, if 1 still gives errors RMA it.
It should run at 200 : ie 200x2 = 400 : 157 x 2 =333.
Never mind the million, a guiness will do.
Cheers
jocko

Install second SATA Drive

Hi,
I currently have a PM G4 with two internal ATA drives installed and one SATA drive installed. I want to install a second SATA drive and have the extra power connection and SATA connection, but my question is where do I get side rails so I can install the secong SATA drive on top of the first similar to how the ATA drives are connected.
Thanks,
Bob

you can if you take your optical drive out.
go here for more info owc.

Adding a second hard drive to late 2008 Macbook Pro

I have a 15"unibody Macbook Pro from Late 2008. It works great, but I only have 320 GB of storage. I would like to add an additional hard drive to store all my files on. Is this possible or do I just need to replace the current drive with a larger one?
Thanks!

Welcome to Apple Support Communities
You can put a second hard disk where you have got the SuperDrive, but in that case, you will have to use an external optical drive.
You just need a peripheral to put the hard disk and a 2'5" SATA hard disk, that can be a SSD if you want. You have the steps and parts to do that on iFixit > http://www.ifixit.com/Guide/Installing+MacBook+Pro+15-Inch+Unibody+Late+2008+and +Early+2009+Dual+Hard+Drive/8526/1

SATA II drive in a SATA slot of PowerMac Quad G5: 1.5GB/sec vs. 3.0 GB/sec

I have a Quad G5 PowerMac with a Hitachi Deskstar® 7K500 (HDS725050KLA360) 500 GB SATA II Hard Drive in the upper hard drive slot. Profiler says this slot is a Serial-ATA slot. Does a SATA II drive in a SATA slot communicate at 1.5 GB/sec instead of 3.0 GB/sec? Any problems with adding a second internal Hitachi Deskstar® 7K500 (HDS725050KLA360) 500 GB SATA II Hard Drive?
PowerMac Quad G5 Mac OS X (10.4.8)

Not sure how you landed here. This is the discussion area for the iBook G4.
You probably want to ask your question in the Power Mac G5 discussion area.

Adding a second time capsule?

I've reviewed some of he discussion on adding a second Time Machine but two issues arise. The information relates to older Time Machine software and leads to confusion.
I have an Airport Extreme with S/W version 7.6.4 and would like to add a newer Airport Extreme to back up the older one. Reading the suggestions on adding a new TC didn't cover the newer Time Machines and I could find Apple's instructions for doing it.
Somewhere I read that the new TC could be connected to the old TC but forgot the port setup. Also, newer instructions for adding a second TC so both the old and the new acquire the same data could not be found.
Hope This question is clear. Is there help on this?

The network setup is fairly trivial.
Plug TC2 into TC1. (the hardware is Time Capsule.. TC as per your title.. or is it Airport Extreme as per your question..?? Time Machine is software on your computer.. and totally unrelated to the hardware.)
Makes no difference which way around you do it. Plug WAN of the 2nd device into LAN of the 1st device. And setup the 2nd device in bridge.. wireless is up to you.. off or on?? Roaming or not??
As far as backup is concerned.. you need to be clear in the question. And sorry it is a bit mixed up now.
But I can tell you what you cannot do.
You cannot backup to both units at once. You can however setup Time Machine in the computer to backup sequentially to both.
See Q34 http://pondini.org/TM/FAQ.html
The TC itself cannot backup to another TC.
(extreme with hard disk amounts to the same thing.. with caveats)
You can backup one TC to another manually via a computer.. it is slow and I do not recommend it.. if a fault creeps into backup1, you are simply copying said fault to backup2.. AND it is poor for another reason.. Time Machine cannot do it.. you will need another utility eg Carbon Copy Cloner.. and even then you will probably end up backing up a huge amount of data every time.. since TM works so strangely you cannot just backup differences.

Is it possible to install Lion on the second hard disk on my Mini (2010) Snow Leopard Server, and switch between Lion and Snow Leopard? I like those voices Lion has in speech.

Is it possible to install Lion on the second hard disk on my Mini (2010) Snow Leopard Server, and switch between Lion and Snow Leopard? I like those voices Lion has in speech.

When baltwosaid NO emphatically, that was described as CORRECT ANSWER. Ditto in the caeses of the radically different answers from Camelotand Matt Clifton
Could it be that CORRECT ANSWER needs better defining by Apple?
That apart, yes, switching might involve rebooting. About the voices, well, I was the other day adding voice to a commentary in a video I was working on. There's only American English accent in SL — Lion I believe has British ones as well.
Why not, I wondered, try to install Lion purely for academic interest, maybe with an SD card (Sandisk Ultra II, 16GB) as Tom Nelson says is possible at http://macs.about.com/od/macoperatingsystems/ss/Perform-A-Clean-Install-Of-Os-X- Lion-On-Your-Mac.htm

Add a second SSD disk in my MacBook Pro

Hi there,
I added a second ssd hard disk on my macBook Pro.
My question, Would I be able to copy system files and applications to that new ssd, and leave Users Document on my default HDD !
If yes, how can I do that ?
Thanks

http://chris.pirillo.com/how-to-move-the-home-folder-in-os-x-and-why/

Adding a second internal HDD on a Satellite A350-20s

I have a Satellite A350-20s.
It is described in its documentation as having the option to add a second internal 2"5 hdd, and a indeed there is a place reserved for it..
The problem is that when I remove the cover to insert the hdd there is no connector.
So, how to do it ?

Hi buddy,
Well, I have even checked the manual of my Satellite A350 and there you can see that the manual shows second HDD slot. But as Paolo30 wrote installing such a HDD is depending on the HDD controller You can only install such a HDD if you have a second HDD connector.
In my opinion all its ok because the manual doesnt mention that adding a second HDD is possible on every notebook. ;)
By the way: If you need more disk space you can use an external HDD, for example 2.5 one. Such HDDs dont need an additional power supply, you need only an USB cable to connect it. ;)

Difficulty detecting SATA disk, adding a second SATA disk, memory conflict, etc

Similar Messages

Maybe you are looking for