Digidesign Core Audio not working in Logic pro 7.1

Help! I'm not able to use Digidesign's (002 interface) as a core-audio interface for Logic Pro 7. Pro-Tools works fine with the 002. Logic works fine with built-in interface. However whenever I go to change from the built-in audio interface to the core audio 002 interface in audio drivers (in preferences), it won't allow me and I get the following message:
"Audio device has been removed" (press OK) then
"Previously selected audio interface is not available" (Press OK) (digidesign 002 interface has double brackets around the name in the audio drivers). If you try to relaunch driver again it disappears from the drivers list? In addition the "Digi design core-audio " application that opens up on the dock - just says "not connected" and some buttons are greyed out and you cannot "reconnect"?
Is there a conflict of drivers with the OS/Logic version and digi core-audio? I'm running Pro-Tools ver6.4, with digi core-audio 6.9 (updated from 6.4 - didn't solve the issue?), Logic Pro 7.1 and OS 10.3.9 (on a G4 1.25Ghz, 512Ram)?
It seems like a core-audio driver problem - but having updated to the latest version I'm still not getting any joy? Any offers?! Cheers.

Check the FW cable.
Anyway about compatibility Digidesign says this:
Mac OS X 10.3.9 Not Supported
With ALL versions of Pro Tools 6.x for Panther (other than Pro Tools LE 6.8.1 with Mbox 2 hardware only), the highest version of Mac OS X 10.3 that you should use is Mac OS X 10.3.8. There are incompatibilities with Pro Tools 6 and QuickTime 7, which is installed by Mac OS X 10.3.9. If you must use Mac OS X 10.3.9 for some reason, you should revert to QuickTime 6.5.2, available from the Apple website.
cheers
rob

Similar Messages

Focusrite Sapphire and Core Audio not working together in Logic 8

Hello all.
We're having some trouble with our Logic 8 at work.
Today we connected a Bose home speaker system to our Mac Pro via USB.
Once removed and back to our usual output of the Focusrite Sapphire, core audio is malfunctioning within Logic, and the software crashes at the initialising stage.
To offer details;
· We normally run our audio through the Focusrite Sapphire
· Today (the first and last time) we ran the audio through a Bose home system
· We can run system sound though the Sapphire no problem
· Core audio works fine in Logic when the Sapphire is disconnected from the Mac
· The system is an 8 core Mac Pro running Leopard. The software is Logic Studio 8
· Additional software running is Spectrasonics' Omnisphere and East West's Play
We tried to view the crash report in Console, alas that is crashing upon start up too.
Any help would be most appreciated, we're scratching heads and beards.
I've searched the forum for the past year to see if there has been an identical issue.
Lou.

Ahh OK, ( I'm presuming you're using the normal Saffire, not the LE or the pro? )
go here:
http://www.focusrite.com/support/software/saffire/
Download the latest software and install, also within that file there will a firmware updater, run that too.
Let me know the results.

GPO and RA plug-ins not working in Logic Pro 8.0.2

I have installed RA and GPO on my Mac Book Pro. When I open Logic Pro they are not appearing in the Plug-in list. Kontakt 2 is but won't let me load individual instruments for GPO. The strange thing is I also have a copy of Logic Express and both RA and GPO work fine here (even though they don't pass the AU validation). They also work as stand alones fine. In Logic Pro, RA and GPO do not appear in the AU validation list. Can anyone help? I have all the latest updates as far as I am aware. It's very annoying!

There's no Auval or RA or Garritan Personal Orchestra in the Audio Units Manager in Logic Pro. Though Stylus RMX that I also use and Kontakt Player 2 are there and successfully validated. The RA and Kontakt Player component are exactly in the place you said they would be.
I've since discovered that RA does not in fact work in Logic Express. As for whether it's loading up in Rosetta or PPC version - how do I tell that?
I really appreciate your help but I'm still stuck at square 1. Any more suggestions?!!

TS4628 onscreen keyboard does not work in logic pro x

onscreen keyboard has stopped working in logic pro x - latest version.
There is no indication of midi in or out on control bar when keys pressed.
also, certain keys do register do not trigger from outboard keyboard instrument.
when playing back tracks, the relevant keys auto depress on the onscreen keypad.
audio output is fine on the system. all keys on piano roll keyboard work fine.
The onscreen keyboard works fine in garageband
have reset all midi assignments in prefs.
have reinstalled the program but the issue remains
silvejon

You have either installed a midi controller that is over riding things or you are running an iOS App that is interfering....
Turn off all iOS devices to test for iOS App
Delete CS prefs to test for conflicting Midi Controller issues...
Delete the user preferences
You can resolve many issues by restoring Logic Pro X back to its original settings. This will not impact your media files. To reset your Logic Pro X user preference settings to their original state, do the following:
In the Finder, choose Go to Folder from the Go menu.
Type ~/Library/Preferences in the "Go to the folder" field.
Press the Go button.
Remove the com.apple.logic10.plist file from the Preferences folder. Note that if you have programmed any custom key commands, this will reset them to the defaults. You may wish to export your custom key command as a preset before performing this step. See the Logic Pro X User Manual for details on how to do this. If you are having trouble with a control surface in Logic Pro X, then you may also wish to delete the com.apple.logic.pro.cs file from the preferences folder.
If you have upgraded from an earlier version of Logic Pro, you should also remove ~/Library/Preferences/Logic/com.apple.logic.pro.
Restart the computer.

M-audio stops working with Logic Pro as soon as I hit play

I've not found a solution to this anywhere. I've got Logic Pro 9 and hooked up a M-Audio Oxygen 49. The computer and software see the Oxygen okay and I can play any sound I want through the software. Until I hit play - trying to add a track to a recorded song - and the led indicator makes some strange outputs and goes black and freezes. The only way to get it back on is to restart LP. Anyone else have this problem or know what could be causing it? Thanks.

dbaile wrote:
How do I check if the tracks are sending MIDI to the Oxygen? I'm pretty sure that's what's going on but don't know how to stop it. Thanks much.
Have you first tried the test I suggested.
A test... go to the upper left MENU in Logic, select Preferences/Control Surfaces/Bypass All Control Surfaces
Quit Logic, turn the Oxygen Off ot unplug the USB cable, restart the Mac, let it settle a minute, power on the Oxygen, wait 30 seconds and then start Logic. If the Oxygen seems to be working ok then it's control surface related.
Using the Inspector on the right hand side you cab see where the track is sending it's output. MIDI could only be sent to the Oxygen from an Internal MIDI track or an Environment Object with it's output set to the Oxygen IN.
Sounds like a control surface thing to me.
Go to that menu selection I described above and select "Rebuild Defaults"
Then Test
If No change select "Bypass All Control Surfaces"
Test

MIDI Keyboard Not Working With Logic Pro X

I have a MIDI keyboard that I've had for a while. I've upgraded to Logic Pro X, but the keyboard isn't working. I can't hear sound when I play it, nor when I record and try to play it back to myself. What's more frustrating is that I used this keyboard all of the time with Garageband, and there were no issues . It's a simple M-Audio DigiCore MIDI keyboard, and I've updated everything, but I just can't get it to play. I am new to this software, so I'm having a really difficult time navigating this as well, so any help is welcome.

Ok here's what happened, controller was working fine everything set up, then it quit. called tech help at sweetwater, the motu was not seen as a midi interface anymore...went to motus web site, downloaded update for 10.4.4 THAT WAS IT! now it works!
Take note....thanks for your replies!

USB Interface Not Working With Logic Pro 9

Hello,
I've had a Tascam US-1641 for several years now with absolutely zero issues on my old PC. Ever since I upgraded to Mac (early 2011 17 inch Macbook Pro running Snow Leopard) I've had nothing but problems with the US-1641. No matter how many times I uninstall-reinstall the drivers and what USB port I plug it into, whenever I turn on the device and it's connected to my Macbook, it crashes my operating system and it freezes everything I was doing. Logic Pro doesn't load and when it sometimes does (10 minutes later), it immediately crashes when I click anything.
I've tried several tips to fix it and nothing worked. The most popular choice was select the default input/output in Logic to the system audio, then quit Logic, turn on the interface, then restart Logic. No such luck. I have to reboot my machine at least 5 times, uninstall/reinstall the driver and hope it works to use the interface. I thought it was the operating system, so I upgraded to Mountain Lion and installed the new driver for Mountain Lion, after of course deleting the other drivers and removing all previous data, and it is still giving me the same problems.
I don't have the money to afford a replacement model or a different interface from a different company, so I'm hoping you guys can help me figure out what exactly it is that's causing the interface to freeze my operating system and crashing my Mac whenever I try to use it. I am getting extremely frustrated at this and as much as I love OSX and Logic, what good is this piece of software if I can't use it? I need help.
Thank you.

The problem lies with Tascam and their inability to write stable drivers for OS X... and isn't anything to do with Logic Pro ..
As you know, you are not the only person to have had this issue and the reality is, while the 1641 might work fine with Windows, when it comes to OS X Macs.. it's an entirely different story... depending on the version of OS XS you are running.
The one tip I have read, that seemed to fix it for most people.. (Though not all) is as follows;
(Thanks to Paulypaulpaul for this)
-uninstall your tascam driver 2.10
-restart
-install driver 1.03
-restart
-plug in your tascam
-goto where you download your drivers (http://tascam.com/product/us-1641/downloads/), scroll down to the bottom where it says firmware, Download the firmware 1.02 (3rd from top under firmware), install it. your control panal should now read 1.03 for your drivers and 1.02 for your firmware.
-install drivers 2.10
-restart
Follow each of the steps exactly.. including all restarts when indicated..
...and good luck...

Amp designer and pedal board not working in Logic Pro 8

Hello! I am new to LOGIC PRO 8 and maybe my silly question has a easy answer. When I want to record a guitar or a bass in the audio channel created for it, and want to insert for example a complete rig, the sound won't load and a message will apper saying "pedalboard not available" "amp designer not available" or pedal not available". If I open Mainstage 2 or Garage Band and I play, pedals are working and all amp modulation as well. If I go and look into the application support and plug-in settings folders it seems to me that everything is there. What am I missing or doing wrong? how can I solve the problem and make these enable for recording? THANK YOU FOR HELPING!

primocaster wrote:
"pedalboard not available" "amp designer not available" or pedal not available".
Hi
Amp Designer and Pedalboard plugs are in Logic 9 only...
CCT

Built in Audio not working in MacBook Pro after update to 10.7.3

The Built In Audio is not working in My MacBook Pro (Early 2011) after update to 10.7.3; I tried resetting the PRAM and SMC but it didn't helped me out. I can get audio only if i reboot my mac from Safe Mode or reboot after Repairing Disk Permissions in disk utility using the Recovery Partition;. If i make a normal restart or just startup then the built in audio disappers (audio is displayed gray in the menu bar) . Everything was working well with the 10.7.2
- Audio Works well with the Boot Camp Partition. and There is a sound during boot up.

I dont have any backups and i dont have time capsule or an external hard drive ready to be used for backup.
My macbook is my the only one computer. The problem is that the animation is lagging when i change the window to dashboard or safari or mail or another window. Inspite of this my macbook works well.
But 5 minutes ago, I noticed that if i run autocad on my mac- the lags go away!!!!

Overdubbing not working in Logic Pro X

Hi everyone,
I am running LPX 10.0.5 on my Macbook Pro (Mid 2012) with OS X 10.8.5 and unfortunately midi overdubbing (for software instruments and external midi tracks) seem not be working for me. The Replace button is of course deactivated and the midi recording settings are set to "merge when cycling" (translated from German, I don't have the English version).
Any help would be much appreciated.
Regards

Hi
I've looked at the info posted above and I still can't get this to work consistently in Logic Pro X - 99% of the time it just doesn't work. I'm beginning to think this is a bug. I have also ensured that the "Drag: Overlap" is set as I think by default it is set to "No-Overlap" - not sure if this makes a difference but I read in the Apple Discussions Forum that this affected some other users.
My project setup is a follows:
Record->MIDI Recording Options->Join with Selected Regions
Punch/Overwrite - Disabled
OSX Mavericks 10.9.1
Logic Pro X 10.0.5
Any help on this would be appreciated as I just can't this to work as it did in Logic 9
Thanks
Neil

Novation Remote 25SL Not Working with Logic Pro (Logic Automap)

Hi,
I can't seem to get my new Novation Remote 25 SL to work in Logic Automap mode.
I have the Remote SL in Logic AutoMap (template #39). When I launch Logic Pro 7, The Remote SL shows : "Logic AutoMap" on the Left LCD display, and nothing else happens, it seems to be frozen at this state. The Up/Down arrows on the Left side don't change anything.
Any clues why this is happening ?
I have read many posts on this and other forums of user issues in setting the Remote up properly, and have it work in Logic Automode. Tried many configurations, and settings, re-installed sw, OS 1.0.13, but no luck so far.
I would like to hear from Logic Pro 7 users who have successfully setup their Remote SL with Logic Pro 7.2.1 in Logic Automode, and are working with this system without any issues.
This will be very helpful in figuring out if there is something wrong in my settings, or if the unit itself is defective, or I am doing something wrong during the installation of the software ? I have been trying to get this thing to work for the past two days, with no success so far.
The Remote SL should be a wonderful controller for Logic Pro 7 (once it works !) so, I'm being as patient as I can with this thing.
I'm using Logic pro 7.2.1 on a Mac G5 2.5 Quad, Mac OSX 10.4.6
Thanks.

Hi Blaze,
I tried your settings, but no change, the Remote SL is still frozen showing :
"Logic Automap" on the left LCD .
You mention setting "Mixer View 64" well the parameter I see is called :
"Mixer View Fader" which I guess is the same one you are referring to. I set it to 64, it was set to 8, but has not changed anything. Still having the same problem. This problem is dragging into Day 3, what a bummer.
Thanks.

Apple remote is not working with Logic Pro 8

Hi all
Anyone any idea why, it would really help me as I need to remotely activate the record button. Many thanks Dave

My guess: it is simply not compatible with 10.6.8 (which was released well after Logic Pro 8)

Export audio to video AAC not working in Logic Pro X

Hi
Anyone else have this.
When I choose to export audio to movie, and select AAC, it exports but when I chack the file, it has actally used PCM.
Regards
Keef

Did you ever manage to get this figured out?

Audio not working on macbook pro

Hi,
I have a 2007 Macbook pro. I have changed battery for this laptop twice in the past 5 years. As everyone else, I experience overheating issues. Otherwise, it has been working fine.
Today, I started using the itunes store to browse tv shows, books, and music. Suddenly I heard a big rattling noise (really loud) in my mac and it was coming from the top left side (probably the fan!). I quit the applications and shut down my laptop. When I restarted the mac, I could not listen to any songs neither from my mac nor from the internet, say youtube. No audio of any sort is working in my mac right now, not even the alert sounds.
- I checked the system preferences and could not change any output controls.
- After sometime, Ive also started noticing the red light in the headphone jack. But, this red light comes on intermittently. I tried putting my headphones in and out 3-5 times, it still did not solve the issue. The light may go off, but there is still no audio from my mac.
- Everytime I restart my mac, I hear the rattling sound. I checked my hardware, repaired the disk (using the Mac OSX disk), reset SMC, PRMV settings. None of these helped.
Im worried that my fan has gone bad and this in turn has also affected my internal audio system for some reason? I would appreciate any troubleshooting tips in this regard!
Thank you!

Well, for the red light issue, cut the end off a Q tip, or clean cut a Wooden tootooth pick(NO PAPAER CLIPS OR ANY OTHER CONDUCTIVE MATERIAL) and GENTLY "massage the headphone jack,(there is a micro switch that can hang, stop at the LEAST amount of resistance). Reboot see if that helps.
Also go to system preferences>sound>output tab and make sure the mute box is not checked, set the volume slider is at least half way up, and make sure built in speakers are selected.
If this does not solve your issue, go to utilities>Audio/MIDI set up, click putput tab, and make sure source is set to built in speakers, when selected double click on the built in speakers log out and reboot.
If you have been using Garageband, launch GB and go to GB preferences>Audio/MIDI, and select from the output tab intrenal speakers.
Here's what worked for me. It's not a workaround, this acutally solved the problem and I haven't had speaker issues since.
Go to "Activity Monitor" (you can hold "Command" "Shift" and press "U" if you're on the desktop).
Locate "coreaudiod" under "All Processes"
Right click it and click on "Quit"
After several seconds, "coreaudiod" will restart on it's own and your speakers will return to normal.
I tested this by restarting to see if it was a fluke workaround. Then I turned it off and waited a day (I had things to do so the waiting a day was easy lol). Turned it on, it was fine. I put it on sleep mode, waited 10 mins. and took it off of sleep mode. It was fine. Everything went back to normal for me.
Rattling sound is a concern for me as ths not normal, I would back up eveything, as this could br a HDD on the way out, and you want to save your data.
Also, you can try a a Pram reset:
If you have a removable battery, power doen your MBP, disconnected the power adapter, remone the battery, hold the power button down for 10 seconds, reinstall battery and mag safe and booy up.
If you have a MBP that has a non removable battery, follow the folling instructios.
Power off MBP, power it back on, holding the following keys: option, command,P,R, (no commas), press these key immediatly before the start up chime ringd, continue you to hold therse keys till you hear the start up chime ring ring 2 timess amd release.
Reboot
Since you had the battery replaced, you might want to try an SMC reset if non of the above offers any help. Power down MBP, power back up, hold the following keys before the star up chime. Left key shift,control, option, contine to hold these keys till the gear stops spinning.
Rebot.
All the best, I hoe this helps.
Let me know if this worked for you

Midi keyboard key A2 not working with Logic Pro 8

Hello
I was using an m-audio keyrig 49 for a good 3 months, when all of a sudden the A2 key stopped working properly. The transport bar in logic shows that midi data is being received when I press A2, however there is no velocity value. The key only makes a sound when I'm going from another key to it, and even when that happens there is a sustain effect on the note, which aren't on any other keys.
I have tested this on midi keyboards from m-audio, novation, and edirol... keyboards that require drivers and keyboards that don't require drivers.
Any ideas?

Try redefining the key commands. Sometimes they can be a little flaky when importing earlier key commands. Redefining them might "unstick" them...

Digidesign Core Audio not working in Logic pro 7.1

Similar Messages

Maybe you are looking for