Digital In AND Out on 6024E

Hi
Is it possible to set 2 lines of the digital port on write (Output) and the other 6 on read (Input)? if yes, how do I have to config the DIO and which vi's do I have to use.
thanks a lot for your help
Yves

Line direction is set by DIO Port Config.vi. It can be found at the Data Acquisition>Digital I/O>Advanced Digital I/O palette. There's an input called line direction map. A line is an output if it's bit is 1 and an input if it's bit is 0.

Similar Messages

Playstation 3 Digital out to Mac Pro 3,1 Digital in and out again through Konnekt 6

So I got a used Mac Pro 3,1 on craigslist and it's a beast. Only problem is that the superdrive was broken. No big deal really, but I've been thinking about how it'd be cool to be able to watch blu-ray movies on it. I Could just buy an 80 dollar drive, or I could use my Playstation. I've got optical outputs on the PS3 and inputs on the Mac, so my question is what the easiest way to route the sound would be. Just using audio/midi setup? Usually inputs need to be "armed" so that there isn't that constant stream of info and I imagine with digital it's the same? Would I have to open up Logic and do some kind of soundflower bed magic?
Thanks!

Ok so I'm home now and continued my seach... and found this:
http://reviews.cnet.com/8301-13727_7-20075185-263/workaround-for-audio-problems-with-os-x- 10.6.8-update/?part=rss&tag=feed&subj=MacFixIt
I won't be able to try it until back in the studio tomorrow but it may just be what I need - will report back here. Seems that it is an OS issue though and not an Adobe one.

What are the iTunes digital audio levels in and out

I am having a lot of trouble with finding out and setting the audio levels in and out of iTunes.
Digital audio has 16bits at '1' with an analog signal level of +12dB, 24bit has all'1's at +18dB. Making the overhead capability for CD 16bit 12dB and that for HD 24bit 18dB.
I would like to record (using SoundStudio) a set of standard audio tones from 20-20kHz with digital levels of "all 1's" 16bit, or +12 dB analog level, "all 1's" 24bit ditto, and the same for levels of analog 0dB (-12dB digital) for 16bit and 0dB(-18dB digital) for 24bit.
What I am finding is that if I get Sound Studio to inert a tone at what it calls 0dB, save it as AIFF, then the output it from iTunes I get a much higher level, around +8dB or so!
Any ideas?

As an addition to my first question. I asked the makers of Sound Studio about levels. They tell me that the Mac standard is to have all '1's in the digital stream defined as 0dB.
Which helps as I can now record a tone at the CD level of -12dB and the HD audio level of -18dB. And if I make recordings I know to keep the input levels well into the green, not yellow and definitely not up to the red.
As you say the output of iTunes is boosted, and from my measurements this boost is in the analog circuitry and is about +8dB.
I woul dnot recommend turing down the iTunes volume control as this brings in the digital volume reduction, which depends on the algorithm they have implemented. This is not so bad for iTunes as the Audio Core software works at 32bit and can handle 16bit volume changes fairly well. But on the iPad it is different as iOS is only 16bit audio so the volume algorithm is poor. So always leave the volume at maximum and turn down your HiFi volume control!
Or use a digital output to an external DAC as the iTunes volume control is then disabled. Set Audio MIDI for 24bit output and you are ready to go with HD Audio.

Optical digital audio cuts in and out

I am connecting my new Apple TV 2010 to our Bose Lifestyle 28 (Apple TV HDMI to VS-2 and Apple TV Optical Digital to the Bose Lifestyle). After power cycling the Apple TV the audio works but cuts in and out every few seconds.
All thoughts appreciated.
Thanks in advance, Jay

Even after switching DD to "On" switching cables and ensuring that I was playing back audio content with DD encoded audio, I still receive no DD audio and continue to get audio drop outs.

Digital Audio Cuts In and Out

I have an earily 2009 Mac Pro hooked up to my Onkyo TX-NR3007 via digital audio (optical TOSlink). When I play a movie or music it cuts in and out. Maybe 30 sec of sound than nothing for a few seconds then sond again. I have tried 2 different cables. It is not the media because it does not happen in the same spot twice. I have also tried a differnet opt in on the receiver with the same results. I'm running up to date OS 10.7.5,
Please help I've tried everything I can think of...

Even after switching DD to "On" switching cables and ensuring that I was playing back audio content with DD encoded audio, I still receive no DD audio and continue to get audio drop outs.

Analog in digital in and digital out slow ?

Hi
6261 PC board used.
I have 5 analogue channels as input, 2 digital channels as input, one of which is a trigger for the analogue
sample read. The analogue samples are written to a labview measurement file (.lvm) all this
is fine and dandy and can read up to about 720 k samples/s.
But when I try to output the second digital input (the one that isn't a trigger), I do not get an output
that is related to the input (using an oscillioscope to view input and output). The input shows
about 5 pulses to the outputs one. Eventually I want to sample the second digital inputm and
delay it slightly before outputting it, but I want to be confident I will be getting the same number
of pulses out.
I even trimmed to vi down just have one dig in, going straight out, and it still didn't match the
number of pulses.
I am using DAQmx throughout, could that slow things down (using express DAQ) ?
any help appreciated,
sandra

here is my latest vi, I am still having some problems.
I created this vi from the 'Gen Dig Pulse.vi' example, I have changed it to
generate the pulse according to ticks rather than frequency and I have
added the trigger.
The source of ticks is a digital pulse from an optical encoder that is sending
out 360 pulse per revolution of an engine crankshaft, the trigger is from the
same optical encoder, but it one pulse per revolution. I require the
output to be of the same frequency as the trigger and delayed by a
configurable number of ticks.
The output is ok for up to about 400 revs per minute, but after that the output
is intermittent and some pulses are lost.
If anyone can take a look at the vi and advise me on this I would be grateful.
I have tried leaving only the 'wait until done task' in the loop, but this gave
no output, I also tried adding an implicit 'timing' task, but this gave to many
outputs,
regards,
Sandra
Attachments:
Gen Dig Pulsetickstrigger.vi ‏32 KB

Ipod seen as a digital camera, and won't be recognized by Itunes.

Have: Ipod 2nd Generation (2.2.1), Windows Vista, Itunes Ver. 8.1
Problem: Alright here it is, my Ipod and my sister's is not being recognized by Itunes. It is however recognized by my computer as a digital camera. If I shutdown my computer and then plug in my Ipod while its off into the computer while its turning on its recognized. However, it won't sync saying "the ipod cannot be synced. the disk could not be read from or written to." Now it trys to sync but my Ipod doesn't have syncing on the screen. My Ipod though will be recognized by other computers.
Things I tried: All the steps on the apple page, please don't link me to the instructions again. I have uninstalled and installed Itunes soo mny times. Tried restoring it also, but couldn't finish the restore on my computer and had to use another one. Also I have tried plugging it in and out, using differant usb ports, pretty much everything with no success.
PLEASE HELP!!!

Welcome to Apple Discussions
I know it is your first post so I'll offer a gentle reminder to start new problems as new posts and not hijack an existing thread. Your problem is different than the OP.
In your case, you need to disable the automatic camera notification. The help article how to that is here: http://support.apple.com/kb/TS1857
The crashing part can be caused by an obsolete/incompatible driver on your PC. You will have to figure out how to update it so it doesn't crash or remove it entirely.

Can you do Digital In or Out on the same port (byte) as PFI timing?

I'm using an M series board with three digital ports. Port 0 is only for DIO, ports 1 and 2 can be used for DIO or PFI (e.g. clocking, triggering). My question is: can I do both DIO and PFI functions on any one port. For example, on Port 1, I would like to use bits 0 to 6 as Digital Inputs and have an external clock signal go into bit 7 as a clock for Analog Out. Can the port be mixed like this?
Thanks,
Dave
David Thomson Original Code Consulting
www.originalcode.com
National Instruments Alliance Program Member
Certified LabVIEW Architect
There are 10 kinds of people: those who understand binary, and those who don't.

Dave,
The DIO lines on any DAQ device that uses the DAQ-STC ASIC can be configured on a per line basis, so using PFI and DIO lines on the same port will work just fine.
You can run a quick test on this using the "Gen Dig Pulse.vi" example (found in the NI Example Finder under Browse -> Hardware Input and Output -> DAQmx -> Generate Digital Pulses). You should be able to generate a pulse on one of the PFI lines on the board, then read that pulse back in on one of the DIO lines of that port using an external connection.
-Justin

How to use the Digital Audio in & out RCA jacks a6010n

On the lower right of the back of my Pavillion a6010n desktop, above the mouse and keboard connections and below the monitor connection are two RCA jacks labeled Digital Audio in and out. The top one has an orange insulator and is labeled "out", and the lower one has a black insulator and is labeled "in". I have been unable to find any information about these or how to use them. Can anyone please tell me or direct me to information about this? I have Vista Home Premium 32 bit and have added a Sound Blaster Audigy sound card which is cheap but has a better S/N ratio. In Control Panel --> Sound the digital output for the sound card is listed but there is nothing about the Digital Audio jacks I would like to be able to use. Thank you all.

Yes there is. I suggest trolling these boards for the 3rd party remote solutions that will free you to use the remote in ANY application like Winamp, Notepad, Windows Media Player, etc.
Just my two opinionated cents...

Making keyframing as smooth as behaviors (ease in AND out)...

I try time and time again to get keyframes to be as smooth as behaviors with "ease in and out." No matter how I do it, bezier, ease in, ease out... the keyframes always jerk in one direction or another. Is there a way to have keyframes exhibit this "ease in and out" behavior? When selecting the keyframes in keyframe editor, it only offers an ease IN or and ease OUT.

I'm more focused on camera-moves (no pun intended). Dolly, sweep, these all have "ease both" options which feel VERY organic. Without them I think 3d comes off as "digital," so I prefer to always use ease-both.
When I start key-framing for major complex moves, I have to bezier the **** out of X,Y AND Z moves. It gets really overwhelming. I just would like the option to select all and choose -ease-both-, rather than have to set each one.

"in port" and "out port" VIs are not in the functions palette!

Hi,
I am using LabVIEW 2012 on a Win 7 64 bit. I want to read a digital input (3.5V) using PC parallel port. I also read this white paper:
http://digital.ni.com/public.nsf/allkb/B937AC4D8664E37886257206000551CB
I searched all the functions palette for “in port” and “out port” VIs but I could not find them. Apparently they are not supported in 64bit OS. What are my alternatives for reading digital input via PC parallel port?
Thanks.

They have not been supported for quite some time. What happens when you use the recommended VISA api?

Determining in and out Gamut values for RGB profiles

Hi all,
I am looking into how to check if a swatch value falls within my .icc profile gamut.
If I have a color value for example L=74 a=12 b=-37 and I want to see if it falls within my .icc profile I can select Edit>Convert to Profile and choose my profile
I then can select the swatch and see if there's a gamut warning there.
With the above swatch if my color profile is "Photoshop 5 Default CMYK" I will get the warning, if I change the profile to "US Newsprint (SNAP 2007)" I won't get it.
This works great for CMYK profile.
My question is how to check if the color falls inside an RGB profile?
I have tried changing the document intent to Web and Digital Publishing and changing the RGB profile but only changing the CMYK profile affects the out of gamut warning.
Does any one know of a solution to this? The same issue would appear to be in photoshop.
Thanks in advance.
Trevor

Timo,
actually he wants to set the attribute mapping dynamic, reading the field to map the return value to from a custom property.
1D10T,
If this could be done then in the Def object of a view object (which means its not per user session but use). Investigate into the View Object Def object for the view object that defines the list of value (not the one that you use as the LOV list source)
Frank

Setting in and out points in list view.

I am in list view. I am showing several favorited clips from one video. Say I am playing back the third favorited range and I want to select in and out points for that favorited range. The video is playing and I hit i. I am immediately jumped from the favorited range I have selected to the first favorited clip in the list. When I click back on the clip I was setting the in point for I find that it has set the in point where I wanted. The entrire process then repeats when I try to select the out point. Set out point. Jumps up to first clip. Click back on original clip to get to my out point.
This is very frustrating and makes using favorites and list view a huge waste of time. Can anyone help?

That should not happen. Before anythign else, do these two things.
1- Go into the "Final Cut Pro" menu, "Command", and be sure "Default" is checked. Quit out of FCP X.
2- Open System Preferences (Apple menu), Keyboard, Keyboard Shortcuts. Click the "Restore Defaults" option. The issue here is OS shortcuts will override app shortcuts.
3- Launch FCP X and try again. If that doesn't fix it...
4- Download the free app "Preference Manager" from Digital Rebellion (dot com) and use it to delete the FCP X pref files.
After you've done all of these, report back and let us know what's up.

Best digital camera and camcorder...

What are some good budget digital camcorders and a digital camera for the MacBook? My wife and I are expecting our first child in December and we're both in college (I have a degree in visual communications, and I'm going back for computer programming), and she's going for nursing.
We're kind of tight on money fixing up our house and getting things ready for the baby, and I've got 'proud parent disease' where I wanna take pictures and video tape EVERYTHING all the time.
Any suggestions?

My suggestion is to not cheap out on a digital camera (no experience with camcorders). It may save you money up front but the quality of the product may come back to bite you (much like getting a Windows PC versus a Mac ).
I use this review site: http://www.steves-digicams.com/
I'm not an expert, but among my circle of very amateur photography friends Canon is considered to have the best quality lenses and image processors. I myself went with a Canon PowerShot A540, a 6-megapixel consumer model, and it's been great. The A-series filled all of my requirements--took AA-type batteries instead of expensive proprietary ones, had features that the super-compact line didn't, including good basic video recording (for quick clips), and it wasn't as bulky as an SLR or "prosumer" model. My brother and another friend got the A540's less expensive sister, the A530; the only reasons I didn't go with that was the smaller screen and the video recording wasn't as good.
I'd avoid Kodak and HP branded cameras, as well as any generic brands. Most everyone else should be decent too, including Sony, Fuji, Olympus, etc.
G4 dual-533 Mac OS X (10.4.6)

Audio IN and OUT messed up - how to diagnose??

I've got a weird issue and wondering if anyone can help. I have a Mac Pro and yesterday got a good mic and a pre-amp for my son to do some recording on GarageBand. I also installed the CuBase software that came with the pre-amp. The audio in and out is very erratic. Sometimes it will record, and sometimes not. And it will not playback properly (yes, I double-checked my Output/Input settings in System Preferences).
The same problem is happening on the CuBase software (which is GarageBand on steroids).
HOWEVER, when I fire up iTunes, all my existing MP3s come out of the speakers (line out) and headphone jack just fine.
Anyone know if there are potential conflicts between the system and audio editing software? Or perhaps it's the sound chip on the motherboard?
Related question: Can you add a sound card to a Mac Pro? I know the chip is soldered to the motherboard, but wondering if I can bypass that by adding a sound card?
Thanks for any help.

I haven't spent much time with Garage Band and I haven't used Cubase since OS9..
But there may be settings right in the DAW software that sets the default ins/outs as opposed to having your system settings control where the audio goes..
Another thing to take a look at is Audio MIDI Setup in the Utilities folder. It displays the system sound settings in a bit more detail...
Currently, there might be 1 or 2 PCI-express "sound cards" out there, but your best bet would be to look for a USB or, preferably, a Firewire audio interface. There are many of these out there with a large range in pricing..
If you are getting serious about recording, you may want to look at some of the small format mixers which include a USB or FW output. The advantage of these small mixers is that they are like swiss army knives for audio.. they allow you to route and mix audio in all kinds of ways that you would never imagine until you actually need it.. Some include digital effects, usually some EQ on every channel, from 2-16 mic pres, etc
Another route, again if you are getting more serious, is to get a ProTools LE or M-Powered setup. This way you are getting "Industry Standard" recording software along with a selection of different audio interfaces to choose from depending on your needs..
Apple Logic is also Pro-Level Software for a great price, especially at the current pricing.. You still need an interface, though, to get the most out of it.
Browse around the computer recording section at www.sweetwater.com to get a good idea of what's involved..

Digital In AND Out on 6024E

Similar Messages

Maybe you are looking for