Digital in port/sound blaster audigy plat. + Playstation 2. will it wo

I would like to know if i hook up the playstation 2's optical out to the optical in on the audigy platinum's dri've bay panel, will the sound work from the computer speakers, or will i have to have another piece of equipment, or change a setting in the computer?
Just want to know before I spend at least the 30 bucks on the optical cable.

I dont know why i didnt check that before....works now. but its putting out some infrequent static, and the sound skips frequently. i've updated the drivers when i first reinstalled the system...all the updates were applied. but i guess i might try to reload the originals and see how they do

Similar Messages

Sound blaster audigy plat. EX

i recently bought a sound blaster audigy platinum EX(not the audigy 2 plat. EX)i was just wondering if the sound from this sound card is better then the on board sound of the k8n ne plat. i have a feeling that it is, i just want to make sure. also, has anyone had any problems installing this type of card and if so how did you go about fixing them? thanks

siruis,
go to the mixer settings and one of the sliders. the one
beside the wave slider to the right and slide it down to about 40% and try it, while playing if static still present
slide it down more while the track is playing, i had the same prob wwith li've 24bit 7. and this cured it for me.
hope this helps you.
john ( good luck )

Digital 8 Track & Sound Blaster Audigy 2 ZS Plati

I have a Korg D8 Digital Recorder. I recorded some of my songs to it this afternoon, and now I want to get the music saved to my PC. How can I do this? I have the optical out on my Korg hooked up to the front of my PC at the optical in on the Sound Blaster. Now I have no idea where to go from there. Any help would be greatly appreciated.

Get to know below mentioned software st.
Set Audigy for recording (CT Surround Mixer or Windows Play/Recording Controls and Creative Audio Console or CT Panel) -
- select playback and recording source: S/PDIF n + enable it,
- S/PDIF n settings ->set samplerate: same as you have used in Korg, bit-accurate recording
- before final recording, just chck if you can hear anything coming from Korg
Depending on what you like to do...
Record from Korg as Stereo:
- open Creative Media Sourec (or any other recording software)
- set input and recording source to S/PDIF n
- record
Record every 8 tracks in Korg into individual tracks in software (if this is possible to do in Korg ... send one track at a time):
- get some multitracking/sequencer software
- set track for recording, set input source, record one tarck at a time --> add a new track in software for every new track send from Korg ...
jutapa

NO Dolby Digital or DTS- Sound Blaster Audigy 2 ZS Platinum

So after doing a clean install from Win XP to 7 PRO I now no longer can get dolby digital or dts through my speakers via toslink (optical, whatever u want to call it) . I have the latest win 7 drivers, tried reinstalling drivers using compatability mode (vista sp2), and configured it to play on on only digital outputs, spidf decode, set spdif output as my default device, set speakers to 5., and all combinations of that.
I am also using the k lite codec pack and playing videos using media player classic.
However, If i test dolby digital through? windows sound options it will detect and play the sample sound in dolby digital but my movies, etc will not when play through MPC.
PLEASE HELP!

? You are needing to do AC-3 passthrough and you may want to use the Shark Codec Pack instead of K-Lite. Instructions for Shark's pack are here:
http://shark007.net/forum/Thread-problem-spdif-passthrough-x-fi-decoder-Win7

Sound blaster Audigy 2zs platinum setup with creative inspire 5.1 digital 5

what should the setup be for the sound blaster Audigy 2zs platinum and the reati've inspire 5. digital 5500 because with the decoder in i only get center fl fr on games. i dont get sound from the rear speakers.but when i take the decoder out and just plug the 3 leads straight into the back of my sound card i get 5. any help plz.i done a thx sound test with the decoder in it does fl i can hear it but i can hear the center as well
and no sound comes out on the 2 rear speakers when doing the test.but when puting the 3 cables straight into the back of the sound card i runed the test and i could hear all the speakers fine even the rear speakers any help plz is this ment 2 happen or do i have to change some settings thanks for any help plz help me thanks.

I Have had a problem for ages. I have the Audigy 2 ZS Platinum and Inspire 5. digital 5500.
I have copied the advice I received/didnt recieve from creative.
Best of luck
Dear Martin
Thanks for your reply
I am sorry for the problem you are facing.
To achieve outputs from all the speaker during speaker test, you will need to have an analog connection, or digital DIN connection.
That will be possible if you connect the three line out jacks on your soundcard, to the three audio input (analog jacks->green,black,orange) on your speaker, if it has this connection. Or, you may connect them using Digital DIN, if they have this connection.
If you are using digital connection (coaxial, optical), there will be no way to achieve sound output from all the speakers during 5. speaker test, as they carry stereo signal.
Best Regards
(Mod Note: Name Removed)
Creative Customer Support Services
Creative Labs Europe:
Original Message Follows:
Hi
I understand you must be busy, so no problem.
No I do not hear EAX when in Pro-logic mode. I only hear (depending on the game in question)
Half life two: front left-right and centre. NO rears
Fear: Front, left, right, & centre. No rears
Farcry Front left, right & centre. No Rears
When I run your speaker test HISSSSS, No Rears, no front left or right
Beats me?
Regards
Martin
-----Original Message-----
From: CLE Customer Support [[email][email protected]]mailto:[email protected][/url]]
Sent: 24 January 2006 5:44
To: Martin
Dear Martin
I apologize for the delay on the answer.
If you select Dolby Prologic mode on the decoder, are you able to listen
the game audio, with EAX, in all of the speakers?
Regarding to the optional bay dri've, you can purchase it from ou
Best Regards
(Mod Note: Name Removed)
Original Message Follows:
Hello
Your email was helpful, unfortunately, not for my unit, you see I would
have
connected the Jack leads in by now if the inspire had Jack lead inputs
as
you describe
Please don't think I am being sarcastic, but from reading the
correspondence
below it would seem as if your department is having difficulty
understanding
my problem.
Also it would seem your department doesn't have the necessary technical
information on your very own product, so to help with your dilemma I
have
taken photos of the input/outputs on the Inspire unit.
You will clearly see the inspire has no inputs other than Coaxial and
Optic.
This leaves me back to my last post. I think the solution would be for
me to
purchase the correct processor, which would have come with the original
sound card had I not been a little tight on the money front.
I have attached a photo of the sound card with the processor, I would
love
to buy this processor but find myself unable to locate this product on
your
web site. Would you possibly be able to send me the correct link to this
item so I can buy this Processor Please?
Kind regards
Martin
-----Original Message-----
From: CLE Customer Support [[email][email protected]]mailto:[email protected][/url]]
Sent: 8 January 2006 0:3
To: Martin
Subject: RE: CLE -
Dear Martin
Thanks for your reply
Your soundcard is Audigy 2 ZS
Your speaker is Creative Inspire 5. Digital 5500
You will need to have a 3:3 cable(with the color green, black, orange)
to connect your soundcard to your speaker, to achieve the 5. effects
with games.
Below is the connection:
- Connect line out jack of Audigy 2 ZS
to 'Front' of Creative Inspire 5. Digital 5500 using the green color
connection
- Connect line out 2 jack of Audigy 2 ZS
to 'Rear' of Creative Inspire 5. Digital 5500 using the black color
connection
- Connect line out 3 jack of Audigy 2 ZS
to 'Center/Subwoofer' of Creative Inspire 5. Digital 5500 using the
orange color connection
Once you have done the correct connection, play the game DOOM3.
Ensure you have selected either the EAX or surround option in the game
settings.
Does it work?
Best Regards
(Mod Note: Name Removed)
Creative Customer Support Services
Creative Labs Europe
Original Message Follows:
You have lost me. Your sound card clearly states that I can have EAX
surround decoding from the sound card I have purchased.
All of the games on your web site claim to give me an environmental
effect
that will blow my mind, hence EAX.
All I have done wrong is NOT buying your decoder that comes with the
sound
card. My mistake.
All I want to do is re-address this issue and buy the correct
decoder/processor.
Can you point me to the correct link on your web site so I can buy the
correct decoder/processor?
As for the PCM out of the above cables, this foxes me as my other
equipment
only use Optical cabling on my Lexicon processor and from that I have DD
7., DTS 7. and meridian 5. lossless.
My issue is more to do with NO EAX from the rear and centre channels
while
in-game.
Kind regards
Martin
-----Original Message-----
From: CLE Customer Support [[email][email protected]]mailto:[email protected][/url]]
Sent: 6 January 2006 09:3
To: Martin
Subject: RE: CLE - Technical Support Request (KMM887805I6636L0KM)
Dear Martin
Thanks for your reply
All commercial digital connection eg. optical or coaxial cable will only
carry PCM stereo signal. If you want to output the signal to a surround
5. with extra EAX environment effects, it will not be possible at all
since it is only restricted to stereo channel signal.
As per current industry limitations, we are bound to follow the standard
one-signal output for all our SPDIF and Optical output jacks. This is
something that is currently shared by all vendors for all products.
Please note that all games are not dolby digital, even they are , it
will require certain motherboard to encode it to dolby digital signal,
which our soundcard does not support.
You can only use analog connections to gain true 5. surround for
gaming..
email.
Best Regards
(Mod Note: Name Removed)
Creative Customer Support Services
Creative Labs Europe
Original Message Follows:
Hi Joong
I don't fully understand your email, but I do get the gist of what
you're
saying and understand I need to connect the analogue cable to fully
appreciate the sound in EAX.
Would you be able to tell me what product I could buy from your
catalogue
which would marry up with the sound card I have, as I understand now
that
the Inspire 5. will not do the job.
Kind regards
Martin
-----Original Message-----
From: CLE Customer Support [[email][email protected]]mailto:[email protected][/url]]
Sent: 6 January 2006 04:00
To: Martin
Subject: RE: CLE - Technical Support Request (KMM8875697I6636L0KM)
Dear Martin
Thank you for the reply.
Computer games written with support for 3D audio do not require a Dolby
Digital Interacti've Content Encoder (DICE) to output multichannel sound,
with no exceptions. Sound devices that support the real time encoder
technology from Dolby will simply receive the multichannel wave file
output and encode it in real time to a somewhat modified Dolby Digital
bitstream. Creative does not support the Dolby Digital Interacti've
Content Encoder on any of its sound cards.
The only difference between a Sound Blaster card and an audio card that
has a real time encoder, is that you can make a one-wire, digital
connection from your audio card to your home theater receiver and enjoy
discrete multichannel sound from the game. However there will be a
continuous, slight delay, known as "latency", as the encoder is creating
and transmitting the bitstream, and of course the compression scheme
being used is "lossy" (i.e. not bit-accurate).
If you want to enjoy 3D audio in 3D enabled PC games in multichannel
surround sound with a Sound Blaster card, it is recommended that you
connect the analog outputs of the sound card directly to the analog
inputs of the receiver. This will require 3 cables for 5. surround
sound, one for front right and left, one for rear left and right, and
another one for front center and subwoofer. Though it requires more
cables than a real time encoder system, it will not have any latency
issues. When connecting PC audio to a home theater receiver, Creative's
latest sound cards such as Sound Blaster Audigy, Sound Blaster Audigy 2
are likely to provide higher quality audio than any Dolby Digital real
time encode system available for the PC today.
Please retain all the previous correspondence when replying to this
email.
Best Regards
(Mod Note: Name Removed)
Creative Customer Support Services
Please do not use this link to submit technical queries
Original Message Follows:
Hi
One particular game which has "in-game" DD is Farcry; I used this as my
benchmark disc for DD and to push my Nvidia 7800 GTX GPU's (I have tried
it
on friend's machines and they get the full surround effect so I Know
this
version is ok. I also have ALL of the game patches & updates.
I would like to point out that while playing Doom 3, Half Life 2,Fear,
Colin
McRae rally 04,FIFA 2004,Meddle of honour pacific assault, Rome, Shadow
ops, All these games have EAX HD, which is enabled within the options
menu
"in-game", But I do not get ANY use out of the rear's and I might as
well
listen in stereo.
No, inspire 5500 does not automatically switch while "in-game" when DD
is present as you would expect, but does if it was a Movie, which makes
me
think the DD stream isn't getting to the processor.
I originally thought I could put all this to rest if I could buy the
control
panel that would have come with the Sound card if I had not tried to
save
money, but every time I search your accessories site I get completely
lost,
it really isn't user friendly, the sub-menus are very time consuming and
point you in the wrong direction because they are not categorised as Joe
public would understand
I downloaded your TEST Movies and creative demo player utility, ran it
but
still no EAX HD or DD if that were present.
I want to put this card and Processor into my boys computer (which is
the
same Spec as mine and I will update to the FX series, but I am unwilling
if
I cannot find a logical reason why this set-up cannot work first.
Would it have anything to do with the pins on the Digital out on the
sound
card plug, the one I bought and was attached to the last email? Only
sending
certain channels down to the processor?
Regards
Martin
-----Original Message-----
From: CLE Customer Support [[email][email protected]]mailto:[email protected][/url]]
Sent: 5 January 2006 08:09
To: Martin
Subject: RE: CLE - Technical Support Request (KMM8868993I6636L0KM)
Dear Martin
Thanks for your reply
Your speakers are fine as you mentioned that there is sound from all the
speakers when you are playing movie.
May i know what game are you playing when there are no sound from the
rear speakers?
Have you done the appropriate settings in the game to achieve the 5.
sound?
Is there any game patches that you will need to update?
Does the Dolby Digital LED light up when you are playing the game?
Please retain all the previous correspondence when replying to this
email.
Best Regards
(Mod Note: Name Removed)
Creative Customer Support Servic
Original Message Follows:
Hi
I am sorry; I should have said the Inspire 5. was model number digital
5500
S/N SW330030026.
The inspire has these connection on the back of the processor
>From top/back of unit
Audio Outputs
Front
Rear
Centre/subwoofer
Audio inputs
Audio line in
Coaxial
Optical
DIN
The Din to a remotely located Subwoofer which has the speaker leads
inputting into it. Plus power.
Attached is the creative view of the controls menu and I have attached
the
invoice I was sent, it shows the lead I was told to fit.
As I said, I can now hear DD5. while within a movie from ALL speakers
BUT
no sound from rears during IN GAME DD5.
I do not use this PC for films only games.
Regards
Martin
If you are having a digital connection, it is normal for only get only
front left/right is you use the speaker test option.
http://us.creative.com/support/kb/article.asp?l=3&sid=4858
Speaker test only outputs from two front speakers?
You mentioned that that you are unable to get any sound from the rear
speakers when playing game right? May i know are you using a digital
connection? May i know what speaker settings have been made under
Creative Speaker settings?
Do get back to me on the above.
Thanks
Original Message Follows:
Operating System: Windows XP Professional x64 Edition
Creative Model Number: SBO 350
Computer Brand/Model: home made
Processor/CPU: AMD 64
Memory: Gig DDR 4
BIOS Type/Revision: 5. 39
System Board/Chipset: ASUS A8N-SLI Deluxe
Detailed Problem Description:
I have the above Sound card.
I also own Inspire 5. amp/processor
I Wanted to save money by connecting above sound
card to amp/processor
Connections on sound card made life very difficult
I contacted Creative for help. you told me to buy
an RCA to mini jack cord which also has other connections, from your
web site, (I tried to find
the product number for you, but your sub-menu
system is so poor I couldn't locate the RCA/mini
3.5 /to phono link for you) this cord connects
directly into the digital in, on the sound card (3.5 Mini jack) to the
coaxial input on the
inspire 5. amp/processor.
I have enabled ALL sp-diff settings and digital in
setting on every program/utility/kitchen sink and all.
I have an SP-Diff wire from DVD burner to creative
sound card, and yes its enabled and digital only
is selected.
I can play a DVD and see the inspire 5.
automatically change from Pro-logic to Dolby
digital when it See's an AC-3 stream.
when I try and play ANY game you say has EAX
,2,3,4 I cannot get any sound from my rear
speakers (see above in Dolby Digital ALL speakers
work correctly)
when I enter the set-up menu within the creative
software you supply with the sound card and select
5. speaker, digital only, test the speakers via
the white noise function, all i hear is left and
right noise. no centre, no rears.
I phoned you tech support line, the boy on the
phone didn't have much of a clue about your
product and I had to tell him what connections sit
on the inspire 5. series amp/processor.
I want to build another PC for my son, I want to
add the FX series sound card and amp, but i am not
willing to buy anything until i feel you have
helped me to solve this problem first.
please can you help, I am at the end of my tether
with this sound card.
kind regards
Martin Waite
Message Edited by Daniel-CL on 0-28-2006 :36 PM

Creative Sound Blaster Audigy 2 ZS With WinTV Expr

Hi,
I am using a Creative Sound Blaster Audigy 2 ZS sound card, and I recently purchased a Hauppauge WinTV Express card, I have installed the card with no problems, but it says I have to connect a wire from the Line Out port on the WinTV card into the line In port on my sound card. I cannot find a line in port onm the back of my sound card so I am getting so sound from WinTV. Can anyone please tell me how to set it up correctly?
Thanks for your help,
MJJOS.

The Line In jack is the second jack from the Digital Out jack. If you have problem locating those jack, you can checkup the user guide too.
Jason

I have some Audigy card Sound Blaster Audigy SB1394 EAX ADVANCED HD maybe can

I have some Audigy card Sound Blaster Audigy SB394 EAX ADVANCED HD maybe can i get some info about this card.. it is 5./6. some details about it. i found it in my closed :P
it will be great if someone help me about this card. because i have my SB li've Value if this audigy better i'l just change it.

i think it is an Creative Labs SoundBlaster Audigy with 394 PCI Sound Card
32-Bit Professional Quality Effects Engine
? Creative's Audigy? patented effects processor
? Support for real-time digital effects like reverb, chorus, normalizer, pitch shifter, or distortion across any audio source
? Capable of processing, mixing and positioning audio streams using up to 3 available hardware channels
? Full 32-bit digital mixer maintains all sound mixing in the digital domain, eliminating noise from the signal
High Definition Audio Quality
? Playback of 64 audio channels, each with its own independent sample rate
? 24-bit Analog-to-Digital and Digital-to-Analog conversion
? 6-bit recording with sampling rates of 8, .025, 6, 22.05, 24, 32, 44. and 48kHz
? Supports Sony/Philips Digital Interface (SPDIF) input and output of up to 24-bit/96kHz quality
? SPDIF output up to 24-bit resolution at selectable sampling rate of 44., 48 or 96kHz
? Low latency multi-track recording with ASIO? support
EAX?ADVANCED HD?, Advanced Audio and 3D Audio Technology
? Optimized user-selectable settings for headphones, two, four or six speakers and external A/V amplifiers
? Dolby? Digital audio decoding to 5. speaker channels in both analog and digital modes
? Upgradeable 3D audio architecture for future improvements
? Hardware acceleration of EAX ADVANCED HD for games
? Creative Multi Speaker Surround? (CMSS) technology places any mono or stereo source in a 360? audio space
? User-selectable EAX ADVANCED HD music presets, pre-configurable DSP modes simulating various acoustic environments
? Time-scaling
? Audio Clean-Up
SB394 Connectivity
? High speed connection to IEEE? 394-enabled devices with up to 400Mbps transfer rate
? Interconnection of up to 63 devices for peer-to-peer communication
? SB394 Certification Program thoroughly tests and certifies participating vendors' 394-enabled devices with Sound Blaster Audigy for optimal performance and ease of use
? Hot-plug support for ease of connecting or disconnecting external devices
Realistic Wave-Table Synthesis
? Creative's Audigy music synthesis engine
? 64-voice hardware polyphony with Creative's patented 8-point interpolation technology that reduces distortion to inaudible levels
? Uses SoundFont? technology for user-definable wave-table sample sets
? Unlimited sample size can be loaded into host memory for professional music reproduction (limited to available system memory size)
? Scalable PCI wave-table synthesis architecture with multi-timbre capability
? 48 MIDI channels with 28 GM & GS compatible instruments and 0 drum kits
MIDI Interface/Joystick Port
? Support for analog and digital or DirectInput? game devices
? Support for two simultaneous MIDI devices with Sound Blaster Audigy Dri've
On-Board Connectors
? Analog / Digital Out (Analog Center & Subwoofer / 6-channel SPDIF Output)
? Line in
? Microphone in
? Line level out (Front) / Headphone out
? Line level out (Rear)
? SB394 port
? Telephone Answering Device in
? Analog CD Audio in
? Digital CD Audio in
? Expansion header to an external 5-pin Joystick / MIDI port
? Internal SB394 header to Sound Blaster Audigy Dri've
? Expansion header to the Sound Blaster Audigy Dri've
Sound Blaster Audigy Audio Performance
? Signal-to-Noise Ratio (A-Weighted) = 00dB
? Crosstalk (Left/Right and vice versa) = -00dB
? Total Harmonic Distortion + Noise at kHz (A-Weighted) = 0.004 %
? Frequency Response at -3 dBr = <0 Hz to 22 kHz

Help with Sound Blaster Audigy Value 24-bit..keeps crashing when connecting to the inter

pls help..every time i connect to the internet while playing mp3's or just any applications or programs that produces sound and even when streaming some clips through the internet, my computer restarts..any sound that is produced when i am online it will restart..but if i just surf the net without playing anything..it works fine...
how cn i solve this problem..
pls help..thnx
my spec:
AMD Sempron 2400+
Epox 8rda3i
Seagate 80gb
Palit GeForce 6600gt
Creative Sound Blaster Audigy Value 24-bit

screwguy_28 wrote:
is this the one?
IRQ 0 System timer OK
IRQ Standard 0/02-Key or Microsoft Natural PS/2 Keyboard OK
IRQ 3 Communications Port (COM2) OK
IRQ 4 Communications Port (COM) OK
IRQ 5 Uni'versal Serial Bus (USB) Controller OK
IRQ 6 Standard floppy disk controller OK
IRQ 8 System CMOS/real time clock OK
IRQ 9 Microsoft ACPI-Compliant System OK
IRQ 9 SCSI/RAID Host Controller OK
IRQ 0 MPU-40 Compatible MIDI Device OK
IRQ NVIDIA nForce PCI System Management OK
IRQ 2 PS/2 Compatible Mouse OK
IRQ 3 Numeric data processor OK
IRQ 4 Primary IDE Channel OK
IRQ 6 Sound Blaster Audigy OK
IRQ 8 SoftV92 Data Fax Modem OK
IRQ 9 NVIDIA GeForce 6600 GT OK
IRQ 2 Standard OpenHCD USB Host Controller OK
IRQ 22 Standard OpenHCD USB Host Controller OK
Everything seems to be OK so it's propably the drivers for your modem that is causing the issue. Just try if updating them helps anything.
Also, you can turn the MPU-40 (onboard MIDI/Game port) if you dont need it.
jutapa

Setup could not detect any Sound Blaster Audigy card on your system

Hi from Barcelona!
I've a Soun Blaster Audigy card (Model: SB0090)
I tried to install the Audigy software and drivers from the original product CD but Setup was unable to find Augigy hardware and halted the installation!
"Setup could not detect any Sound Blaster card on your system. Please ensure that your Sound Blaster hardware is properly installed before running this Setup program"
By the way. Manually the sound drivers can be installed working only front speakers of the 5. Creative system
I tried a clean installation of Windows XP and Windows 2000 PRO (reformatted the hard dri've) but Audigy install CD still could not find Audigy hardware.
I've changed the card to a different PCI slot with the same results!!! Damaged?
What is happening? I need a solution!! Many users have this problem to with other Sound Blaster cards and models...

ADSLNEW wrote:
It seems to be an important BUG of Creative Sound Blaster Audigy cards related with EEPROM!!!
Yes, indeed, that is my theory as well. After much ****hing and on-line research, it seems that this problem has been around since 2002. From Creative Labs point of view, it appears they view this as "pilot error" -- the user has installed the card in a system that is not fully compliant with the latest standards -- specifically Microsofts ACPI (configuration and power management). A wide variety of configurations and/or actions seem to cause the PCI subsystem ID in the Audigy EEPROM to be erroneously overwritten -- including certain older motherboards, certain older PCI cards, and perhaps other actions.
Once the subsystem ID in the EEPROM is overwritten and has garbage information, many or all of the Creative applications cease working and various sound problems can arise. Attempts to reinstall the driver or update to the latest driver consistently fail becuase of the dreaded "Setup could not detect any Sound Blaster Audigy card in your system..." error message.
There appear to be four fixes:
) Get a replacement Audigy card from Creative, but <EM>only</EM> after you perform their prescribed troubleshooting steps to prove that the card is indeed the source of the problem. Apparently, the steps include installing the card in another PC. Apparently, Creative in Europe is more willing to replace your card than Creative in the US. It's up to Creative Labs whether or not they issue you an RMA ("Return Material Authorization").
However, this fix will fail if the root causes of the EEPROM error are not corrected. Apparently, Creative Tech Support isn't always a foolproof source of guidance, so the burden is on you. The root cause MUST be corrected before the new card is installed, or the same problem will happen all over again. Eliminating the root cause may involve replacing your motherboard, replacing other PCI cards, or manual configuration (disabling ACPI).
2) Reprogramming the EEPROM. This is for advanced PC owners only, because it involves desoldering the EEPROM, programming it, and resoldering (and even lifting some pins to prevent reprogramming). There are instructions on how to do this posted in the German Creative Labs discussion board, by a Russian (!). I have links for those who are interested.
3) Removing the Creative drivers and software (using Clean Sweep procedures and third party utilities), updating again using Windows XP SP2, then physically moving the card to different PCI slots (multiple times if necessary), until ACPI Bios writes the proper information into the EEPROM. You can then reload the drivers.
Again, the root causes of the problem must be removed or your fix will only be temporary (a day or two). This solution also seems to be very dependent on the specifics of your system (motherboard, PCI cards, etc.).
4) Some people have had success in by-passing the step in the driver installation process where they check for the Audigy card subsystem ID, using a utility called CTZAPxx on the installation CD. Then then manually install each of the applications they need to use.
5) Use the open source driver from the kX Project (http://kxproject.lugosoft.com/index.php). This driver (and associated utilities) does not depend on the detailed configuration of the card (i.e. they don't check subsystem ID) and appear to work fine even with cards with corrupted EEPROM.
This driver is aimed primarily at computer music applications, and opens up the on-card signal processing capabilities. The downside is that the Audigy 2 ZS does not have all of it's capabilities supported <EM>yet </EM>(e.g. Dolby Digital decoding, S/PIF passthrough, possibly some game sound features, THX, 24-bit recording, support for Hyperthreading CPUs, etc.). But scanning over the discussion boards, the user community seems to be MUCH happier with the performance and support associated with these drivers than with Creative's.
This is the direction I'm going. I'm not a big gamer and I don't really care about the latest in home theater audio performance. Basic 5. surround sound is all I care about, and I'm much more interested in computer music capabilities.
I have also lost faith in Creative Labs as a vendor to provide the support I want and need going forward. Just imagine if the Creative Labs were running the Space Shuttle program :smileysurprised:.

Vista and Sound Blaster Audigy

Okay I am getting desperate. I have been searching all over for this odd occurence but I havent found anything. I am running a dual core amd processor with Vista 64-bit, 4 GB RAM, and a Sound Blaster Audigy. I purchased this card off of ebay, so I dont exactly know the model (it is the one with a firewire ( ) port on the actual card, and a tan/white i/o box that goes in my cd dri've bay; the box just plainly says Soundblaster Audigy). Anyway, the card had been working great with the drivers at first, and I then had a kernal file fail on me. Well, after recovering successfully with the Windows disc, I came back to find out my drivers had messed up. I tried many combinations of uninstalls/reinstalls, different packages, etc and nothing seems to work. However, the odd part is that sound works within the windows environment (system sounds/clicks/etc), and also through the line in on the breakout box, AND in FLStudio/Reason/Windows Media Player. However, I am not able to get sound through flash movies, Winamp, PC Games, and media things of the sort. I was wondering if anyone else has had this odd occurence, and knew how to fix it. Thank you.
PS
The error I get on Winamp is Bad Directsound driver. Please install proper drivers or select another device in configuration. (I have also messed around with the Winamp output with no luck).

http://forums.creative.com/showthread.php?=3033
Try here.
the above driver pack from Daniel Kawakami is top notch and works very well. Good bass response and I NEVER had a problem when using these in XP, Vista, Vista sp and later Vista 64 Sp and 2.
cheers,
jmacguire

Sound blaster audigy midi p

I bought a SB Audigy2 value bulk, this card haven't a onboard midi port; is there the possibility to buy and connect a midi port?

Originally Posted by karloch
Hi everyone!
I recently purchased a Sound Blaster Audigy RX and I'm very pleased with the improved audio quality over the Intel HDA included in my motherboard.
However, I have a problem when playing MID files using hardware midi synthesis: I select the correct midi device "SB Audigy 5/Rx Synth A" and play the midi file using Windows Media Player. I can hear the tune, but with LOT of noise. As this problem is only happening with MIDI, I wonder if it is a driver issue or a faulty card. I have tried with official Creative drivers and with the Daniel_K's SB 5.3 support pack with same result.
I'm attaching an MP3 file of the MIDI output you can get a clear picture of what's happening.
ffaboss_short.zip
Should I replace my card or is it a software problem?
Hi karloch,
Pardon me for saying that I did not detect the noise you mentioned in your attached MP3 file. I can't be sure it's the noise or is it part of the music; especially towards the end of the playback. I'm using VLC player btw.
Perhaps, you may like to test it with another media player.
Cheers,
JL-CL

Set up from creative down load does not detect any sound blaster audigy mess

I have a sound blaster audigy with no installation cd. I installed the card to download the drivers. The detection software on the site said there was no creative product installed.
I downloaded the web update file and saved to my desk top. Ran the file after closinging all apps and got a message that there was no audigy detected. Reinstalled the card, same, did it again in another pci slot.
Tried finding a driver in xp, found one for soundblaster. No sound at all with this xp driver. I do not have intergrated sound on the abit k7rsa board. How do you install the driver if the set up program stops you because it does not see the device, and with no install cd? Thanks for any help.
Tony

I have the same problem. About a year ago I threw out all my driver cd's because they were really piling up and i figured i'd never need them because I've been able to download all the driver's i've ever needed from company websites.
NOT SO with Creative.
I have the Sound Blaster Audigy 2 Platinum (the one with the ports for the front of the computer). I recently had to reinstall my OS. I got the soundcard to work, but all the optional components I had before (like the ability to use the remote control to control sound, and the EAX console etc) are gone. I tried to download these components from the website (it's really hard to tell which is which, so i downloaded them all). They will NOT install! I keep getting the error message "Setup did not detect required components, Setup will exit" on all the download software.
This is extremely frustrating because I'm unable to setup the speakers properly (windows speaker settings don't really work).
I did manage to do the automatic update thing, but it only updates the core drivers.
PLEASE HELP!
I paid $200 bucks for this card (granted, that was a couple years ago), so I should be able to at least download the same software that came with the product!
Please have a professional (not an engineer without user interface experience) design the download area too...it is extremely difficult to understand what the individual components really do! At the very least, when you download them...they should work!
Thanks.

Sound blaster audigy 2 zs...NO SOUND! he

i've got a sound blaster audigy 2 zs...had it for two years...this morning, all of the sudden, it doesn't work...no sound...at all...i've tried uninstalling/reinstalling, speakers are fine (i've had to use the built in audio from my motherboard...NOT the greatest!)...anyone have any ideas, hints, ect. please...help me?:angry:

My Mobo=D875PBZ
perryjp20, After about 25 hours of troubleshooting, finally got my system up 'n running again, including the Soundcard. After a lot of wrong guesses for a "quick fix," simulated re-building the PC from the ground up:
Flashed back to an earlier BIOS (P27, mid-2004). Took out the ATI and Audigy soundcard, disconnected all dri'ves. Booted & shutdown. Added ATI card and monitor, then one 300 gig HD and DVD dri've, then formatted HD via installation of XP Pro, installed original Intel chipset drivers, and XP Pro SR and and set-up 2d partion on HD, installed ATI drivers (originals out of the box), then added Audigy card and its drivers (originals out of the box), then plugged in formatted 2d HD (250 gig). In the process now of adding the rest of my software and games. Shutdown and re-booted at each phase and monitored temps and voltage through BIOS at each phase to attempt to detect any problem with power supply or overheating -- saw no problems.
Will update ATI drivers soon, but reluctant to re-install Win XP Pro SR2.
Don't know what caused the failure of first the soundcard then the system "lost" the ATI card, then HD was corrupted. I was using the Firewire port of the Audigy card (connected to Canopus ADVC) when the sound started cracking/cutting-in-and-out and then went out altogether and the entire system went belly-up. Perhaps that Firewire port is bad? Other leading suspects: BIOS (which I had updated a couple of months ago) or perhaps the system had a worm or virus that Trend Micro did not pick up.

Capturing laserdisc AC3 signal with Sound Blaster Audigy 2 ZS Platinum

I'm considering converting my laserdisc collection over to DVD.
As far as PC hadware is concerned, I have the ATI All-In-Wonder 9800 Pro and the Sound Blaster Audigy 2 ZS Platinum Pro.
My system in a 3.2G P4 on a Intel D875PBZ board w/ 2Gig of memory. Connected are 3 dri'ves, (2) 250G SATA dri'ves and () old 250G IDE dri've that I keep archi'ves on.
The laserdisc player has the following:
AC-3 Bit Stream / PCM Optical Output AC-3 Bit Stream / PCM Coaxial Output PCM Coaxial Output
I was planning to use the optical input of the soundcard but was unsure what to use to capture the digital stream to capture the entire surround channel info. Normally audio is captured as an uncompressed WAV and then converted to AC3 which to me is a wasted step since it's only going to wind up as AC3 again
I've used Virtual dub in the past to capture TV broadcasts, but I seem to be at a loss on this current venture. Any assistance will be great

Alright, let me just double check...
As long as the output from my laserdisc is 48K then things should work fine and I should receive the entire unadulterated stream, no data padding or modification. If it's not 48k then it won't. This is as long as I save it as 2. PCM audio stream
The audiobitrate for AC3 should be at 384k, and this will be preserved using the above method?
From what I'm reading, this unprocessed stream should sound like white noise. Once processed by cooledit , Soundforge or besweet I should have the DD 5. soundtrack intact and not a 2 channel AC stream?
Sorry if I am rephrasing things but I just want to be absolutly certain when I start this project .
Message Edited by madmax66 on -6-2004 02:40 AM

Sound Blaster Audigy 2 ZS Platinum with Vista 64

0Sound Blaster Audigy 2 ZS Platinum with Vista 64Y Hi
I'm considering buying a Sound Blaster Audigy 2 ZS Platinum (with front panel) off ebay, but first I'd like to know if certain features will be compatible with my system. I'm running Vista Home Basic 64bit (hardware is an Asus P5Q-E, Q6600, 2GB of RAM, ATI Radeon HD4850, etc). I'll be using this card for my PC's 5. surround sound system (using the stereo outputs), and more importantly, recording some music. I want to achieve this by using the optical S/PDIF port, as my bass guitar effects board has an S/PDIF output and I've got an S/PDIF cable. I'd also like to use the Line In and Mic inputs. The driver before the latest one for this card said that there was no S/PDIF passthrough for Vista. Has the latest driver got everything I need fixed, so I can just plug it in, install the drivers and then be happily recording through these three inputs?
Thanks for the help?
Message Edited by SuperMaximo on 05-22-2009 2:4 [email protected]

I am brand new to this message system but I am so desperate for help I thought I would try it. After reading lots of comments I find that my problem may be more the rule than the exception. I have an Audigy @ Platinum card and all I ever get from it is crackling and popping. I have been around and around with Creative support but nothing they tell me results in a fix. I am so disgusted at this point that I am ready to just trash the whole thing. I have gone through the BIOS and checked so many settings its a shame. Still crackling and popping. I NEED SPECIFIC ANSWERS FROM SOMEBODY...not just the generic flip the wingle wangle to port xyz and move this to that. here has got to be an answer to this maddening problem. The other thing is that now I can't get my MIDI keyboard to play back. I must have turned something off in the set up process but now I have no idea what to do.
If anyone has any solid answers for me PLEASE come forward with them before I kill someone!

Digital in port/sound blaster audigy plat. + Playstation 2. will it wo

Similar Messages

Maybe you are looking for