Digital output for SB Audigy 2 ZS Platinum Prob

I am trying to connect SB Audigy 2 ZS Platinum to my Amplifier (Sony DVP-NS92V) via the SPDIF coaxial digital connection (I have also tried the digital output at the rear panel), unfortunitely the output i got is only on the left and right front speakers. I am currently having a 7. channel surround system. I have clicked both the dital output only under speaker settings and advanced control for play control, and I have also?tried by using both DTS and THX media file, but still does not work. Can anybody help ?

With a digital connection (optical or coaxial SPDIF) that is normal. Check this sticky thread for more info:
http://forums.creative.com/creativel...message.id=270
Cat

Similar Messages

Cannot select Digital output for ZS 2 Noteb

Hi, I just got an Audigy 2 ZS Notebook card today, installed it, seems to work, but I also got these 5. headphones... The headphones can be plugged in either from the 3 Analog outputs from the card's docking station, or a single /8" cord, which I assume would be digital. I tried using the 3 analog outs, but when I tried to calibrate the 'speakers', front and rear sound exactly the same (front left and rear left sound as if they are in the same position, same with right), so I tried using the single /8" cable plugging it into the card's digital out, and it sounds much clearer, but nothing plays when it tries to play from the center channel or rear channels, and "Digital Output" is shaded so it cannot be selected from the THX Setup Console...
If it helps, I have the Kinyo KY-00 headphones, and they have their own small amp, which may be causing the hissing sound.
Any help is greatly appreciated.

guh. I'm retarded. Somebody delete this topic

CFP-2220 using digital output for status to another cFP-2220

I have two cfp-2220 that I want to connect with each other using the DIO's of 5V that they have.
The problem that I have is that I don't know the impedance to connect the CFP2220-1 Digital Output 1 to a relay for switching the CFP2220-2 Digital Input 1.
I am using a relay for interfacing the signal. This relay needs 34mA 5V to operate. I am not sure if the CFP2220 would have the needed power to turn the relay on and to close the contact that will operate the CFP2220-2 Digital Input 1. In the user manual of the CFP2220 does not mention anything about it.
Thank you!
Gilberto Garza
Solved!
Go to Solution.

Hi ggarza:
Here is the current specification for the digital outputs on the 2220: http://digital.ni.com/public.nsf/allkb/0147137D2442E4A9862572C100758895?OpenDocument. As you can see there, it only supports 3mA, so it would not be possible to use this relay. In addition to this, you should be careful using this outputs, as the manual specifies they are not isolated.
Greetings,
Juan Gil
NI México

Using mathscript to generate multiple digital outputs for switch control

Hello
I am new to this NI LV and a have kind of a basic question. I would like to use Mathscript to generate an array of bolean numbers which will be used to control the Digital I/O lines. I am using NI 6251 USB device and the Mathscript code runs well. But I have a problem using this array to control the Digital output. So I created a simple test programme where I set the DAQ assitant to generate 4 digital outputs(P0.0 ~ P0.3) and it gives error that ".. number of channels in the data does not match the number of channels in the task..." (see attachment) . How can I solve this problem thank you.
Attachments:
K-9.jpg ‏36 KB

looks like you did not initialize all 4 of the elements in the bool array....

Cables for digital output for DTT2500 and Audigy 2 ZS

Hi, I lost the DIN cable for my DTT2500 speakers in a move. I've already read the article http://forums.creative.com/creativel...message.id=270
I'm having a hard time finding the correct cables to get the full digital experience out of my setup. DTT2500 5.1 speakers and Audigy 2 ZS. I game, listen to music and watch DVDs on my computer. Can someone link me some product pages where I could buy the necessary cables?

Hello Jason,
Could you tell me if I can still buy the cable below in order to connect DTT2500 with Audigy 2 ZS?
9-pin Mini Din to 9-pin Mini Din (2 meters - Red)
http://us.creative.com/products/prod...4&nav=features
If not could you provide me the wiring diagram of the Din?
What is the difference between the Red one and the Green one in the shop ?
Thank you

Set Digital Output for Modicon 340 through Modbus Ethernet

Hello,
I used modbus Ethernet example vi and am able to read input coil status of quantity 512
If starting address is changed above 511, VI returns 6002 error.
As per below concept, how can I write to output coil
Output Coils are assigned the block 1-9999
Input Coils are assigned the block 10001-19999
Input Coils are assigned the block 10001-19999
Input Register are assigned the block 30001-39999
Output Register are assigned the block 40001-49999
I also tried sending command directly to TCP IP write like 05 00 AC FF 00 to set a coil. Still its not working.
Can anyone inform how to proceed. Any example or command structure is highly helpful
Thank you

I don't see a "jacks" button on my console, therefore I can't reconfigure the jack to digital.
Is this not available on the Go! unit?

Sound Blaster Audigy 2 ZS Platinum Prob

Hi I recently reinstalled the soundcard and it had problems when I click creative volume control i get the error message "The audio device supported by this application is not detected. The application will exit." and went I uninstalled it freeze at 60%, after that I power down the pc and restart. so I did the Uninstalling
Cleansweep/Uninstalling Sound Blaster given by the tech support. after I restart the pc, and try to install the software again and now it freeze at 95% and the error said software updating please wait for a few mins. did anyone have any idea why. how can I fix this problem.

yingying,
Have you tried uninstalling it in SafeMode?

Vista ultimate x64 any chance to get decoding of dts and dolby digital for audigy 2 zs platinum

hello,
i need the support of deconding dts or dolby digital for my audigy 2 zs platinum pro.
is there any chance to get this feature back in vista ultimate x64?
i hope anybody can help me.
thanks for all
steffen

According to Creative, Vista no longer supports the decoding of Dolby and DTS at the driver level, so no, that feature proabably won't added back in the future. It is gone for all the Creative cards.

Audigy 2 ZX Platinum card - internal firewire ca

Does anyone know where I might purchase an internal firewire cable for the Audigy 2 ZX Platinum card? It is a simple 0 pin female to 0 pin female cable. But not so simple to find!?Any help would be greatly appreciated!

Hello.
I am having a similar problem:
When I first installed the card output to speakers worked fine but the Li'veDri've ins and outs did not appear in the mixer, and they of course didn't work either. Also, the remote control application didn't detect the Li'veDri've as the source of the IR.
After fiddling with the drivers (including doing the AutoUpdate), I shutdown the computer and removed the ribbon, power and firewire cables from the Li'veDri've, unseated my sound card as well as removing the IDE ribbon from it, and booted to Windows. I shutdown the computer again, and reinstalled the sound card and dri've.
The inputs were added to the mixer and Line In 2 and the Auxiliary 2 work, but the headphone out still does not work at all, and, while the Li'veDri've is detected by the remote application, the remote control still does not work. Regarding that, does anyone else's battery rattle in the remote control, especially when placed on a table?
I have checked the pins for the ribbon cable on both ends as well as making sure that the cable is firmly seated. I don't know where to go from here but to Creative's warranty services which take a minimum of 2 weeks to complete.
I also have all of the Creative Apps prevented from loading on startup, do they affect the functionality of the dri've?
Thanks for any insight,
JayMessage Edited by jayatcreative on 0-2-2005 06:46 AM

I don't know how to USE my remote control on my AUDIGY 2 ZS Platinum

I followed the instructions on this page: http://support.creative.com/kb/showa....aspx?sid=2965
about activating my remote control for my AUDIGY 2 ZS Platinum but mediasource did not have a remote control option tab as you can see here...
Untitled.jpg
I just changed the battery on my remote and the receiver blinks when I press a button on the remote but nothing happen no volume change or nothing.
Don't know what else I should do.

You can import the contacts from SIM.
It is covered in the manual:
iPhone User Guide (For iOS 4.2 and 4.3 Software)

Pulse ON/OFF - digital outputs

I have this application where I need to turn ON a digital output for like 50ms or 100ms and turn it OFF. I call it Pulse COntrol
Here is an attachment jpg that shows how I am achieving it.
Another question if I may regarding loop timing. I have a while loop which iterates at 100ms. I choose a certain part of the program and make it a Subvi to clean the program to look more readable. Will the program still run at 100ms per iteration? For example, I have an equation that calculates a valuve from a analog input. To make the program clearer, I put the calculation into a subvi and send info and receive info through subvi panes. Will this affect the loop timing? I hope my question is clearer.
My program does a lot more than just calculate a value, hence wondering. THANKS!
vj
I may not be perfect, but I'm all I got!
Attachments:
p.JPG ‏22 KB

hey VeeJay,
did you want suggestions for how to do your Pule Control a different way, or were you satisfied with the way you have it implemented in the code you sent a pdf of? thanks!
~kgarrett
Applications Engineer
National Instruments

SB Audigy 2 ZS Platinum "colors" the sound of music when played back. How to change th

I recently purchased a Line 6 POD X3 for recording guitar tracks, and when connected using USB it can function as my computer's sound device. Now here is what I observed:
In all cases described below, the "reference" case is that of the guitar played through the POD X3 with headphones connected directly to the POD (no computer sound device involved).
) When I record guitar tracks using either the POD X3 or the SB Audigy 2 as the computer's recording device, and then play the recorded tracks back using the POD as the computer's playback device (headphones plugged into the POD), the sound is exactly the same as the reference case.
2) When I record guitar tracks using either the POD X3 or the SB Audigy 2 as the computer's recording device, and then play the recorded tracks back using the SB Audigy 2 as the computer's playback device (headphones plugged into the SB Audigy 2), the sound is MUCH different than the reference case.
To put it simply, the Sound Blaster card is "coloring" the tone of the recorded guitar (regardless of recording device) during playback. I realize that the Sound Blaster drivers are probably designed to "enhance" sound for gaming and such, but the way it shapes the sound of recorded music during playback is extremely undesireable for home recording projects.
Here is another clue that leads me to believe that the Sound Blaster drivers are responsible for this tone shaping: If I am playing my guitar through the SB Audigy 2 and monitoring the sound through computer speakers or headphones (hooked up to the SB Audigy, of course) WHILE Windows is booting up, I can hear a very distinct change in the sound when the SB Audigy 2 drivers are loaded. It seems to me that when Windows is booting up, the Audigy 2 card allows transparent playthrough before the drivers are loaded, but the drivers then take over and shape the sound.
So, if you've understood my observations, my question is how can I avoid any sort of tone shaping during playback by the SB Audigy 2 drivers? I want completely transparent playback such that what I hear during playback is exactly what it sounds like going in, i.e. the reference case described above.
Message Edited by killrbuckeye on 08-8-2008 02:08 PMMessage Edited by killrbuckeye on 08-8-2008 02:0 PM

Just for kicks, I decided to install this card on a Dell that I happen to have around.. the specs are above and beyond the configuration of my regular computer (whose specs are above and beyond the specs listed for the Audigy 2 ZS Platinum).. and I am unhappy to report that the same freezing problems occur. I am still unable to use any web update features for ANY of my software, and I am still unable to record in 24 bit audio.

Sound Blaster Audigy 2 ZS platinum Pro

where i can buy cable connector ADLINK 1 and 2 for my audigy 2 zs platinum pro? i lived in indonesia

Hi Joko,
Please check your private message.

Audigy 2 ZS Platinum Vista 32bit full support

I would like to know if there will ever be full support drivers for the Audigy 2 ZS Platinum card and the I/O box in Vista 32 bit's? I am looking for the ability to use my 6. speakers correctly and being able to record through Line-In on the card. I would hate to think I will have to go to a competitor for a card that works fully in Vista.

He didn't ask this in 2005, he's registered in 2005, he asked this a month ago (just look again back, I made the same mistake too )?About some replies:Yes the audio?stack in Vista must be very difficult to handle, but the companies had MONTHS, there has been A LOT since Vista's Beta versions and RC etc has been around. Everyone had enough time. I just can't play music correctly because of the current Vista drivers. Furthermore, I can't play my favorite game because some sort of application cslled audiodg eats lots of CPU while anything is playing through my sound card: not a good idea for games as they REALLY doN't run smoothly this way. What I want is not an immediate support, but a well planned approximate date for the new, clean, smooth drivers for Vista. Ok, maybe they are not ready and won't be ready until September, so I'll go back to XP. Or they are maybe ready and the developers are making the last adjustments and the driver's coming in a week or two, so I'll stick to Vista. Creative NEEDS to give this information to the customers, no one has to wait with bogus drivers. I'm not blaming Creative for having their drivers not ready, I understand that, it's technically difficult, but they should at least inform us about when will the drivers be ready.

Audigy-2 ZS Platinum Application problems with New driv

Hello Creative Labs,
I recently downloaded and installed your newly released drivers for my Audigy-2 ZS Platinum card, and some of the software features have now stopped responding and fail to load.
<div class="DownloadDate">Release date: 7 Jul 08<div class="DownloadFileName">File Name: SBAX_PCDRV_LB_2_8_000.exe<div class="DownloadFileName">**?
** This is the patch file name and date released **
<div class="DownloadFileName">?<div class="DownloadFileName">?<div class="DownloadFileName">I Have owned SB products for my entire Computing life, and they have all performed with outstanding results on both Win/98se and XP for me.<div class="DownloadFileName">?<div class="DownloadFileName">The problem I am having since the new Driver update is with the Graphicic Equaliser software, it fails to load now with this new driver release, it gives a small box with a prompt saying "CTEQ.exe !Out of memory", then a larger box pops up about the dimensions of the old Graphic EQ GUI with Equalizer on the header, and a message in the box saying "TODO: Place dialog controls here"
<div class="DownloadFileName">?<div class="DownloadFileName">My microphone is also no longer visible to adjust in the Volume control Main window, I can set my microphone to be the recording device elsewhere in the Windows sound settings, but it no longer is visible to adjust in your Software programs made for my Audigy-2 ZS Platinum.<div class="DownloadFileName">?<div class="DownloadFileName">I see that many other users are also having similar problems, can we expect another update with fixes for the Control panel software to resolve these problems.<div class="DownloadFileName">?<div class="DownloadFileName">Thank you for your time, I look forward to hearing a response from the Creative team on this issue.

All the issues you guys are talking about have been reported in beta stage of these new drivers. I would say none of them has been fixed yet. The only solution for now is to use previous drivers which work fine or use some modified drivers which fixes some issues, but not all. Your choice.
[url="http://connect.creativelabs.com/windows/Lists/Audigy%20Issues/AllItems.aspx">Bug List[/url]
Message Edited by ronon0 on 08-07-2008 :47 AM

Digital output for SB Audigy 2 ZS Platinum Prob

Similar Messages

Maybe you are looking for