Digital to Analog Coversion-Write to Video

I am running FCE, and have no problem capturing video from my VCR via a canopus advc-300 device. However, I am trying to write to video and record a sequence onto a VHS tape, and I keep getting an error message that says my tape is write protected. I know this isnt the case....do i need to change any settings on FCE to allow me to record my sequence to a VHS?

Couple of thoughts:
1) Make sure your audio is mixed down (Sequence>Render Only>Mix Down)
2) I've often found that I have better success with these kinds of outputs if I make a Quicktime reference movie of the project, import that, and play it out of the Viewer while recording
3) What kind of connection are using to go from Canopus to deck? VHS ...S-VHS ... I guess, just make sure you have your cables going out of the box and into the deck. The deck should be on before you even fire up your project
4) Under the View sub-menu, you should have it set to NTSC device

Similar Messages

Dual Monitor (digital vs. analog) and LR2

I have both digital and analog on my video card. Where should I place the
main program on the digital or analog monitor?

> Where should I place the main program on the digital or analog monitor?
That would depend entirely on the quality of the monitor. Let us know more ... including how you intend to calibrate either (altho today's calib systems can generally do either, but sometimes not both).

How can I write a video play to support playing both 4:3 and 16:9 video

I am using Adobe Flash Builder 4 and I want to write a video player to put in my web page. It should be able to play 4:3 or 16:9 videos. How can I adapt UI when display 4:3 or 16:9 videos? Do I have to convert all old 4:3 video to 16:9 video? If I want to create or convert old video to 16:9 video, do I have to use specific codec or video file format? One final question, Does flv support 16:9 format?
Sorry for so many question cause I'm kinda new to video field? Thanks in advance!

Seriously, it's fully rendered. I'm not an FC ace but I didn't just start using the program. It just happens that this is the first video I'm editing that has both wide and standard aspects. I'm telling you that when I try to export in 16:9 (as in QT conversion, picking a 16:9 output) the 4:3 part on the timeline says it's unrendered, but only while the file/location box is up. If I back out totally the red line goes away. If I go ahead with the export I get a green screened mp4.
Message was edited by: matthewmoore

32" Toshiba Regza - can i used digital to analog optical audio converter?

32AV700A - 32" Toshiba Regza
Can I use digital to analog optical audio converter?
My objective is not to use LCD TV internal speakers as it's really bad since the the speakers are on the back. If i use the digital optical cable and plug in to the converter, can all my DVD and other devices connected to the LCD TV play to 1 external audio source instead internal speakers?

Thanks for the suggestion.
I got a bit more noise but still no coherent sound.
What next?

Do we have Digital to Analog converter with high current output?

Do we have Digital to Analog converter with high current output? I need 8 channels and each channel has at least 100mA current output.Thanks!

I have never heard of such a device. You will probably need to follow the D/A with an amplifer for each channel.
What is the voltage range and speed required? Any special protection requirements (such as current limiting)?
Lynn

MAC HANGS WHEN I WRITE DVD VIDEO USING TOAST OR IDVD

DEAR SIR,
I HAVE A PROBLEM WITH MY SONY DVD .. EVERY TIME I TRY TO WRITE DVD VIDEO MY MAC HANGS WHEN TOAST ROXIO 10 STARTS TO LEAD OUT AFTER ENCODING THE VIDEO .. AND IT HANGS ALSO WITH IDVD AFTER ENCODING THE VIDEO .. AND I MUST RESTART MY MAC ...PLEASE TELL ME HOW TO FIX IT ??
Model: SONY DVD RW DRU-835A
Revision: SS02
Removable Media: Yes
Detachable Drive: No
BSD Name: disk2
Protocol: ATAPI
Unit Number: 1
Socket Type: Internal
Low Power Polling: No
Mac OS 9 Drivers: No
Partition Map Type: Unknown
S.M.A.R.T. status: Not Supported
THANK YOU FOR YOUR TIME
TAHA TALAAT
[email protected]

This is a user forum.
Caps is considered yelling, inappropriate, a left over from DOS, too. Oh, and it actually is HARDer to read.

Array of different (digital and analog) values into multigraph

Hello everyone,
So I have an array with a timestamp on the first column, either "off" or "on" string on the second column, and a number value string on another. The columns are based of variables that reads data based on an update rate. My question is, what is the easiest way to separate these values into a digital and analog graphs. This is because the number values are so high that the "off" and "on" signal is being pushed down as the y-axis auto-scales. I'm hoping that I can use a multigraph, but the multigraph puts the data in one graph (since it's one array).
Any suggestions or help is appreciated.

Hi jachy25,
Below is a link to a KnowledgeBase article that goes over how to use stacked plots in LabVIEW.
http://digital.ni.com/public.nsf/allkb/21E8163F259DA2058625703B007511AA
The second link contains a lot of general information on configuring graphs and charts in LabVIEW, and is a useful document to have when configuring plots.
http://zone.ni.com/reference/en-XX/help/371361L-01/lvconcepts/customizing_graphs_and_charts/
I hope this information helps!
Regards,
Kelly B.
Applications Engineering
National Instruments

AD5541/5542 Digital-to-Analog converters from Analog DEvices

Dear Friends,
Does anybody have experience programming in Labview the AD5541 or
AD5542 boards (Digital-to-Analog converters) from Analog Devices (http://www.analog.com/en/prod/0%2C2877%2CAD5541%2C00.html)?
LabView code examples or description of the general approach to this task would be much appreciated!
Thanks in advance

ampm <[email protected]> wrote in news:[email protected]:
> Update: My PXI system has NI-6534 board which I can use
> for digital output. But I need to perform Digital-to-Analog conversion
> by the remote AD5541 board.Is there a way to do this?
That's a chip, not a board. Get the data sheet, look at the logic
diagrams, and you should be able to bit-bang the three logic inputs (well,
two plus a chip select) with your 6534.
Alternatively, the chip uses SPI communication. You can probably find some
help by searching for SPI on the NI site. It also looks like a third party
has a $200 solution the will let you do this via a parallel port, complete
with labview drivers, at http://www.calbay.com/product16.html
Scott
Reverse name to reply

Using Air Port for music...do I need a digital to analog converter

I want to play my iTunes library on my old stereo using my iPod Touch as a remote control (that works well with my Bose Wave Radio). My old stereo is an analog system. When I plug the output of my Air Port Express into my stereo though RCA cable, do I need to use a Digital to Analog Converter (DAC) or is there a DAC as part of the Air Port Express???
Many thanks,
Twinz

After doing a little more digging, I find that using a Toslink cable out of the AirPort Express and into a quality external DAC, and then using RCAs to connect to my pre-amp will get much better results out of my stereo. Evidently the DAC in the AirtPort is not great quality. So, what I'm going to do is hook up the stereo through the AirPort and listen. If it sounds bad, I'll spring for a decent external DAC. Many thanks!

Apple TV great on older DVI TV w/ simple digital to analog audio converter

I bought a Digital to Analog Converter (DAC) for $59.95 to convert optical audio (via Toslink) to RCA analog stereo jacks.
Device I purchased was a DAC-2016 S/PDIF to Analog RCA cnvt.
Very compact!
Also, bought a Belkin Toslink cable for $19.95 at the local Apple Store.
Works perfectly with my HDTV that only has DVI and Component inputs (plus coax, component, etc.)
I just bought it last month.
Googled it a minute ago. Price seems to have gone back up to $89.95. (List price is $99.95.) Not available right now. Maybe Apple TV caused it to sell out.
Let me know if any of you can find this item in stock anywhere or have another solution. I have a friend who has an older HDTV with DVI inputs.
Thanks,
Alan

Finally realized that it was the Gefen box not working!?!?!? I went to the store and asked them to try it out and they had trouble too. Another Gefen was tried and it worked. They all said they had never seen a defective one before. Thanks anyway for your help. It was appreciated!

Breakoutbox for Digital and Analog Output

Hallo everybody
i need to design a breakout box with BNC and SMD connectors for Digital and Analog output (the DAQ cards we use are PXI-6723 for analog and PXI 6259 mostly for the digital an fast AO Channels) I am looking for tutorials and info material for that. On what I have to pay attention what would be a good circuit diagramm design and so on.
Maybe you could give me some tips where I can find good Material about that.
Sebastian

Hello Sebastian
first of all I'll need some more information about your intention. What exactly are you going to do? Do you want to connect, or divide signals? (Which signals?)
Maybe if you have a look in the manuals of the cards, you'll get closer to this. Here you can find out the pin assignment of the cards.
Manuals and specification:
PXI-6723:
http://www.ni.com/pdf/manuals/370822c.pdf
http://www.ni.com/pdf/products/us/04-3513-301-101-DLR.pdf
PXI-6259
http://www.ni.com/pdf/products/us/044063301101dlr.pdf
http://www.ni.com/pdf/manuals/371291h.pdf
Regarding
Gregor Allexi

Can digital and analog channels be simultaneously accessed

Hi,
Is it possible to simultaneously access digital and analog channels on
a Multifunction DAQ (such as NI-4351) by issuing commands from parallel
threads using LabWindows/CVI (5.5.1)?
John.

Hi JAH,
I have no experiance with this product, so can not give you a definative answer.
The best I can do is to suggest you try it, if it does not work then you most likely can not do what you want.
Also what version of the driver are you using, I have checked the
download page and version 2.1 only works for CVI 6 or higher and LV 7
or higher.
Regards
JamesC
NIUK AE

Problem Receiving Digital and Analog Channels- 22LV610U

I have a LCD/DVD combo TV model 22LV610U and had satellite tv for over a year and the tv worked great! After shutting off the satellite, I wanted to only receive the local channels via antenna. I bought a new RadioShack Indoor TV antenna ( to receive basic UHF, VHF and FM radio signals to HDTV and FM HD Radio signals)...
After setting it up, I still only saw snow...I tried setting up the channels through the menu, and was not picking up any signals. I was also unable to view the "DTV Settings" options for Digital Signal...
Do I need a different kind of antenna? I called Toshiba customer service and was told the HDTV antenna would not be compatible, however, ALL channels are now digital and must be received through this kind of antenna...
Help, Im in a pickle Thanks!

If you are using a STB, then you should connect it with an HDMI cable or component cable as you did.
However, you do not need to autoprogram your TV if you are using an HDMI or component or composite or any other indirect connection. That is because the STB is acting as the tuner; it will automatically receive channel information as part of its on-screen graphics. All the HDMI connection is doing is delivering that video feed to your TV.
Therefore, what you need to do is press the "input" button on your TV remote and select HDMI, or component, whatever you are using. Then you control the channels using your STB remote, not your TV remote, which changes the channels on your STB, not your TV. Again, your TV is only receiving the video from your STB, it's not directly changing the channel itself. It's like having a VCR and turning your TV to channel 3 in the old days; you just need to pick up the video.
The reason why, when you tried hooking the TV up directly to the wall with coax is because most FiOS programming is encrypted digital. That is why the STB is needed to "unscramble" the channels and output them to your TV along with all of its on-screen graphics and program guide. Therefore, if you connect coax directly to the TV, the only channels you will receive are local channels (i.e. CBS, NBC, PBS), the ones that Verizon cannot by law encrypt. The reason why some of those channels are "16-2" or "17-214" is because digital broadcasting, as opposed to analog (think the digital transition last summer) uses "sub-channels," which are the -XXX. Verizon can assign whatever number they want to their encrypted programming (i.e. ESPN HD can be 214-1445) because the STB will read that channel and display it within it's own system as Ch. 570.

Sony digital8 camcorder via firewire port, is it digital or analog?

hi all,
I was successful to view & record from my Sony digital8 cam via firewire port. I'd like to know, is this connection analog or digital? Has anyone been successful to record, back up and edit their precious home videos on a G4 PowerMac? And how many DVD discs will it take on a full Digital8 cartridge?
Thanks for your help
Web dude

is this connection analog or digital?
A Firewire port is all digital.
Has anyone been successful to record, back up and edit their precious home videos on a G4 PowerMac?
Yes. Before the G5 came out, many people used G4s (and some still do) to edit not only home videos, but commercial television programs as well.
how many DVD discs will it take on a full Digital8 cartridge?
A standard DVD-5 (single layer disc) will hold about two hours of DVD-Video ... video AFTER it's been properly compressed to meet the DVD-Video standard.
However, if you're asking about raw footage (not compressed more than it was recorded), you should be able to get close to 14 minutes of footage per 4.7gb disc. Digital8 uses the DV codec which requires about 13.3gb per hour of footage. If you recorded the tape in SP mode, you should be able to get just over 1 hour of footage per tape.
-DH

Newbie: 6020E (USB) slow performance with mixed digital and analog input

Hi,
I'm using a 6020E to do analog and digital input, and I'm getting very bad performance.
Please note that doing IO in Labview is new to me!
I have read the post about 6020E slow performance, and it says I should do buffered IO.
Can anybody point me to some DOC or SAMPLE that actually shows or explains how one should do this. I need to read several digital IO lines (which I can combine in one port-read), and several analog inputs.
Seeing how slow the reading on the 6020E is, I am amazed there is only one post that deals with this issue.
I would be satisfied to get the 6020E into some sort of continuous read mode so that whenever I need data, I get the latest reading right away.
thanks,
Peter D'Hoye

Hi Peter,
Your cannot do buffered digital I/O with your daqpad. It doesn't have that capability. You can only make direct software calls with digital read/write from/to your port. So your digital IO is completely software clocked and not hardware clocked. The example you are trying is only for specific Simultanuous sampling boards or now also for M-series boards that are able to do correlated DIO.
Use the Cont Acq&Graph Voltage-Int Clk.vi example for your analog measurements. (NI Example Finder) For your digital IO you can only use the examples like Read Dig Chan.vi, Read Dig Port,...
There are indeed some slow performance issues with single point I/O Operations, that is correct.
Check the explaination below:
DAQPads are offered for the Universal Serial Bus (USB) and the IEEE 1394 (also known as FireWire). Both of these standards use a high-speed serial communication protocol between the computer and the device with a bandwidth up to 12 MB/s for USB and 400 MB/s for FireWire.
During a single point operation, the DAQ device requires a complete set of configuration commands. This is done through serial communication (USB or FireWire), making the process slower than in a PCI-based board. The speed obtained for single point operation in a DAQPad is system dependent; this means that your computer processor, memory, bus speed, and other factors alter the speed at which you can do single-point operations with a DAQPad.
For example, on the DAQPad-6020E, timed non-buffered analog input operations are limited to about 50 Hz. At higher rates, the software may become unresponsive. On a FireWire device, you can expect stable operation around 3,000 Hz. But again, these figures are system dependent.
Regards.
JV
NI

Digital to Analog Coversion-Write to Video

Similar Messages

Maybe you are looking for