Digital waveform graph switch between hex and binary possible?

hello,
is there a way to have a digital waveform graph switch back and forth from binary to hex data display?
Thank you

ok, thanks Nathan
Attachments:
Mixed Signal Graph1.vi ‏26 KB

Similar Messages

Bug in Digital Waveform Graph X-Axis

Hello,
I am making separate queried to a database to retrieve analog and digital data over the same time period. The data were logged at 2 second intervals. I have verified that both result sets return the same number of values with the same t0 and dt. I then plot the analog values on an XY Graph and the digital values on a Digital Waveform Graph. I then use property nodes to sync the two graphs (left and right plot bounds, XScale.Range, and Cursor Position.X). After doing this, I can see that the datasets do not line up between the two graphs. The data on the Digital Waveform graph ends several seconds sooner than the analog data. The x scales of the graphs appear to match but the plots don't align in time.
Has anyone else observed this behavior? Is there any work-around?
Thank you,
Peter

There is a much simpler way to synchronize these charts. Just use a stacked chart.
If you use a bundle function you can take two signals (almost data type) and wire them into a Waveform Chart together.
Then on the front panel right click on the chart and select Stack Plots
Since you only have 1 X axis now they are instrincly synched and will always write valules at the same time and update the UI together. You can skip all of the scale synching....
Since the data you are working with has lincked time stamps, the data will need to be matched, (make sure the samples are anyched and each itteration both would have the same number of samples.
The last allternative would be to strip the time stamp off of your data then build a new data structure, with the digital data, analog data and 1 set of matched time stamps. You can then plot this on an XY chart using the time stamp for the X axis for both of your other plots. Let me know if you have other questions.

Digital Waveform graph with a lot of samples

Hi,
I have to display in a Digital Waveform Graph a lot of data read from a file(2.000.000 of samples for 36 signals). If I read the file and I try to display all the data, the Vi became unusable. For example, to zoom a graph region, it may take 30-40 seconds, scroll is impossible ecc, ecc..
Apparently LV doesn't perform a decimation of points. In measurements studio 8, this problem doesn't exist...but I have to use LV 7.1..
any suggestion ?
At the moment I have developed a DLL in VC++ that perform a decimation of samples, but performance are not very good !
Thank you for any idea.
Regards.

Hi Garraty,
Excuse me but I have several questions for you.
1)     Have you tried some kind of incremental approach, starting from 1 waveform and increasing towards 36? Do you experience some kind of on/off degeneration between, les’s say, 34 and 35 waveforms?
2)     How can you decimate a digital pseudorandom sequence of 2M samples without loosing information?
3)     Is this 2M samples an unavoidable constraint for your application?. Actually, it seems very difficult to extract some kind of visual information from a pseudorandom pattern of this length?
Thank you very much.
Kind Regards
FiloP
FiloP
It doesn't matter how beautiful your theory is, it doesn't matter how smart you are. If it doesn't agree with experiment, it's wrong.
Richard P. Feynman

Switch between speakers and headset on X-

I've got X-Fi Fatalty FPS edition and desperately need to find a way to switch between headset and speakers. Especially since I use teamspeak a lot in games and don't want my speakers to echo while I'm talking.
There is an option to mute speakers when the headphone jack is connected, but that requires me to reconnect the headphone plug each time I want to use them.
There must be a switch to turn only the speakers off manually as well?
With Soundblaster Li've! Digital, this problem was easily solved by switching between digital mode on and off, as my speakers were connected digitally and my headset on analog.
But with X-Fi, there's no way to turn off the digital speakers alone.
Please help.

Plug your speakers into the soundcard as usual.
use the front mounted headphone socket on the fromt of the X-Fi I/O unit to connect your headset and set the control panel to automatically mute your speakers when the headset is connected. Your speakers will mute when the headset is plugged in and all you have to do is plug or unplug the headset at the front to switch modes!...Now please do not ask about doing the same with your mike connector!! see other thread by me!! p.s creative do ship a /4" to 3.5mmm adapter with the card.
Hope I have understood your post
AndyMessage Edited by slef2003 on 0-4-2006 03:54 AM

Add plots to digital waveform graph programmatically

Hi Guys,
            This might be an easy one but I can't seem to find the right property. I'm adding "Plot Name" values for a each Plot in a Digital Waveform Graph. I select each plot with "Active Plot" property and name it. However if there are already e.g. 7 plots and I try to set eight plot active (i.e. 7 = Active Plot) I get an error cause this eight plot doesn't exist on the graph, and so can't be named.
    How can I add (or indeed remove) plots using property nodes?
    Thanks

Hello,
One thing to consider is the actual data the graph is receiving. Choosing plot 8 in this case is perhaps attempting to choose a plot which doesn't exist in the data, which could be why you're seeing the error.
Off the cuff, one thought might be to have the following "steps" take place when you want to add plots:
on the appropriate action to create a plot, create a default data set representing that plot
package that with your overall graph data so that the new plot exists in the data
write that data to the graph, perhaps using the Value Signaling property (via a property node linked to the Graph)
trap the graph's Value Change event using an event structure (possibly in a parallel loop) and update the plot name there (much like you are today - using a property node to first set the active plot to <previous value + 1> since you just added a plot, and then set your new plot name)
Not sure what the rest of your application looks like, but hope this helps!
Best,
JLS
Sixclear

Is the digital waveform graph supported in Measurement Studio?

I have an application that could really use the LV-style digital waveform graph in Visual C++. Are there any plans to support the digital graph in Measurement Studio?
Thanks, Bob

Unfortunately, there is currently not an equivalent of LabVIEW's digital waveform graph in Measuremeht Studio for Visual C++. You can fake some of the features with CNiGraph. If you have Measurement Studio for Visual Basic 6.0 installed, you can see some examples of this in the VB DAQ\Digital\Digital Waveform and Digital Waveform Continuous examples. Also, attached is a sample Visual C++ 6.0 project that demonstrates how you can simulate some digital graph features with CNiGraph. There's also a screenshot attached that shows what this looks like. Hope this helps.
- Elton
Attachments:
DigitalGraphExample.png ‏16 KB
GraphDemo.zip ‏19 KB

Sapmmc - jstart.exe keeps restarting, switching between green and yellow

Hi Friends,
I installed the SAP core server ( as part of SAP convergent charging) , but jstart.exe and dispatcher-1 process in sapmmc are noticed keep switching between yellow and green. when the jstart.exe turns green (all process running) , dispatcher-1 turns yellow (waiting to start) and when dispatcher-1 turns green (restart-yes) , jstart.exe turns yellow (some processes running). Only for a small duration , they both remain green (may be during transition).
Trace File is as below: Iam not sure as what is missing here to be installed, as it is complaining about JEE directory in
C:\usr\sap\C06\CCD09\j2ee\cluster\bin, which is not present., which was never installed as part of the installation.
trc file: "dev_jstart.new", trc level: 1, release: "711"
sysno      09
sid        C06
systemid   562 (PC with Windows NT)
relno      7110
patchlevel 0
patchno    92
intno      20020600
make       multithreaded, Unicode, 64 bit, optimized
profile    C:\usr\sap\C06\SYS\profile\C06_CCD09_W2K8-Sap-01
pid        3596
ACTIVE TRACE LEVEL           1
ACTIVE TRACE COMPONENTS      All, egi
Wed Oct 26 04:53:47 2011
trace logging activated, max size = 52428800 bytes, 2 versions
arguments :
arg[ 0] : C:\usr\sap\C06\CCD09\exe\jstart.EXE
arg[ 1] : pf=C:\usr\sap\C06\SYS\profile\C06_CCD09_W2K8-Sap-01
trc file: "C:\usr\sap\C06\CCD09\work\dev_jstart", trc level: 1, release: "711"
ACTIVE TRACE LEVEL           1
ACTIVE TRACE COMPONENTS      All, egi
F
F [Thr 3600] Wed Oct 26 04:53:47 2011
F [Thr 3600] *** ERROR => SfCheckJeeVersion: Cannot find JEE binary directory C:\usr\sap\C06\CCD09\j2ee\cluster\bin. [sfxxmain.cpp 848]
trc file: "C:\usr\sap\C06\CCD09\work\dev_jstart", trc level: 1, release: "711"
ACTIVE TRACE LEVEL           1
ACTIVE TRACE COMPONENTS      All, egi
F [Thr 3600] *** ERROR => SfCheckJeeVersion: Cannot find JEE application directory C:\usr\sap\C06\CCD09\j2ee\cluster\apps. [sfxxmain.cpp 857]
F ********************************************************************************
F Java environment properties (C:\usr\sap\C06\CCD09\work\jstart.jvm)
F    root directory    : C:\usr\sap\C06\CCD09\exe\sapjvm_6
F    vendor            : SAP AG
F    version           : 1.6.0_24
F    cpu               : amd64
F    java vm type      : server
F    java vm version   : 6.1.027 1.6-b07
F    jvm library name : jvm.dll
F    library path      : C:\usr\sap\C06\CCD09\exe\sapjvm_6\jre\bin\server;C:\usr\sap\C06\CCD09\exe\sapjvm_6\jre\bin
F    executable path   : C:\usr\sap\C06\CCD09\exe\sapjvm_6\bin
F ********************************************************************************
F    SAP extensions    : available
F ********************************************************************************
I [Thr 3600] MtxInit: 30002 0 2
dispatcher trace
trc file: "C:\usr\sap\C06\CCD09\work\dev_dispatcher-1", trc level: 1, release: "711"
sysno      09
sid        C06
systemid   562 (PC with Windows NT)
relno      7110
patchlevel 0
patchno    92
intno      20020600
make       multithreaded, Unicode, 64 bit, optimized
profile    C:\usr\sap\C06\SYS\profile\C06_CCD09_W2K8-Sap-01
pid        428
ACTIVE TRACE LEVEL           1
ACTIVE TRACE COMPONENTS      All, egi
Wed Oct 26 06:22:16 2011
trace logging activated, max size = 52428800 bytes, 2 versions
arguments :
arg[ 0] : C:\usr\sap\C06\CCD09\exe\jstart.EXE
arg[ 1] : -appTrc
arg[ 2] : -nodeId=0
arg[ 3] : pf=C:\usr\sap\C06\SYS\profile\C06_CCD09_W2K8-Sap-01
arg[ 4] : -hostvm
arg[ 5] : -nodeName=dispatcher-1
arg[ 6] : -file=C:\usr\sap\C06\CCD09\config\jstart.config
arg[ 7] : -jvmFile=C:\usr\sap\C06\CCD09\work\jstart.jvm
arg[ 8] : -traceFile=C:\usr\sap\C06\CCD09\work\dev_dispatcher-1
arg[ 9] : -javaOutFile=C:\usr\sap\C06\CCD09\work\jvm_dispatcher-1.out
F
F Wed Oct 26 06:22:16 2011
F ********************************************************************************
F Java environment properties
F    root directory    : C:\usr\sap\C06\CCD09\exe\sapjvm_6
F    vendor            : SAP AG
F    version           : 1.6.0_24
F    cpu               : amd64
F    java vm type      : server
F    java vm version   : 6.1.027 1.6-b07
F    jvm library name : jvm.dll
F    library path      : C:\usr\sap\C06\CCD09\exe\sapjvm_6\jre\bin\server;C:\usr\sap\C06\CCD09\exe\sapjvm_6\jre\bin
F    executable path   : C:\usr\sap\C06\CCD09\exe\sapjvm_6\bin
F    SAP extensions    : available
F ********************************************************************************
I [Thr 3828] MtxInit: 10000 0 2
M [Thr 3828] NiInit3: NI already initialized; param 'maxHandles' ignored (init=2;par=202;cur=2048)
M [Thr 3828] CCMS: AlInitGlobals : alert/use_sema_lock = TRUE.
M [Thr 3828] CCMS: Initalized shared memory of size 60000000 for monitoring segment.
M [Thr 3828] CCMS: Checking Downtime Configuration of Monitoring Segment.
M
M [Thr 3828] Wed Oct 26 06:22:17 2011
M [Thr 3828] CCMS: AlMsUpload called by wp 1004.
M [Thr 3828] CCMS: AlMsUpload failed for C:\usr\sap\C06\CCD09\log\ALMTTREE.DAT.
M [Thr 3828] CCMS: CCMS Monitoring Initialization finished, rc=0.
F
Please help.
Thanks.
Edited by: Zain Ahmed on Oct 26, 2011 9:07 PM

HI,
Import the SAP profiles in SAP transaction RZ10: Utilities - Import profiles - of Active Server
OR
Check what messages do you have in jvm_server0.out, dev_server0.out and bootstrap traces,
also have a look at the note 142100.
The first problem is that in the SCS instance there are no running enqueue server as its starting line have no line break at the end in the start profile. Without this NT cannot parse the line. After adding the line break the enqueue server could start.
The second problem is that in the global dispatcher configuration for the LockingManager the en.port was set to 3201 instead of 3200 (which is correct as the SCS instance has the intance number 00).
After correcting these problems the J2EE engine could be started fine.
see similar threads
Dispatcher - Running but Dialog Queue info unavailable
/thread/96588 [original link is broken]
logon710
Message server not starting
Thanks
Swarup

7344 servo motion switching between open and closed loop operation

I have a custom end-of-line test system presently using a 4-axis 7344 servo controller to perform various functional tests on small, brushed DC motors. The system is programmed in C/C++ and uses flex motion functions to control the motor during testing. Motors are coupled to external encoder feedback and third party PWM drives running in closed-loop torque mode from an analog command signal. The system uses all four motion axis channels on the 7344 board to independently and asynchronously test up to four production motors at a time.
In closed-loop mode, the system runs without issue, satisfying the battery of testing protocols executed by this system. I now have a request to add additional test functionality to the system. This testing must be run in open loop mode. Specifically, I need to use my +/- 10v analog output command to my torque drive to send different DAC output levels to the connected motor.drive while monitoring response.
I do not believe the flex motion library or 7344 controller includes functions to easily switch between open and closed loop mode without sending a new drive configuration. I am also under the impression that I cannot reconfigure one (or more) servo controller axis channels without disabling the entire drive. As my system runs each axis channel in an asynchronous manner, any requirement to shutdown all drives each time I change modes is an unworkable solution.
I am open to all ideas that will allow asynchronous operation of my 4 motor testing stations. If the only solution is to add a second 7344 controller and mechanical relays to switch the drive and motor wiring between two separately configured servo channels, so be it. I just want to explore any available avenue before I place a price tag on this new system requirement.
Bob

Jochen,
Thank you for the quick response. The 7344 board does an excellent job running my manufacturing motor assemblies through a custom end-of-line tester in closed loop mode. A portion of the performance history and test result couples the motor through a mechanical load and external shaft. The shaft is in contact with a linear encoder that closes my servo loop.
My new manufacturing requirement is to also sample/document how the small DC motor behaves in open loop operation. Your solution is exactly what I need to perform the additional functional tests on the product I am manufacturing. I see no reason why this cannot work. I was originally concerned that I would need to reinitialize the 7344 board after changing axis configuration. Initialization is a global event and impacts all four channels on the 7344 board.
Using flex_config_axis() to change axis configuration on a single channel without disturbing other potentially running axis channels will solve my concern. It will be several weeks before I can return to the manufacturing facility where the 7344-based testing machine is located. I will update this thread once I verify a successful result.
Bob

When frequently switching between mobile and desktop view

When I frequently switching between mobile and desktop view I have to open the layers every time since they get closed/collapsed. Adobe may need to fix it for the next version.

You can use CTRL+# to switch between Code and Design View.
By the way, this is the Dreamweaver Application Development forum which deals with questions about using server-side scripting languages like PHP or ColdFusion. General Dreamweaver questions should be posted in the regular Dreamweaver General Discussions forum.
And while I´m at it: please use descriptive headlines such as "how to switch between Code and Design View" for your posts -- mentioning your screen name "Goula129" is not helpful to other users.

How to quickly switch between straight and curly quotes?

I've recently moved from a Windows XP machine with MS Office to a Mac Pro with Pages.
For the kinds of documents I typically work on, sometimes I need to have straight quotes, and sometimes curly quotes. With MS Word, I was able to create a couple of macros that would switch these preferences for me. With these macros linked to an icon in the toolbar, switching between straight and curly quotes was as easy as clicking a button.
Now I'm looking for a way to do this -- or something like it -- with Pages.
I know how to switch back and forth using the preferences menu, of course, but I'm looking for something quicker and simpler, since I often have to make this change several times a day.
Can Automator do something like this? Or is there another way?
-- Eric

Turn off the auto correction and you can type Curly quotes with:
left single ‘ option ]
right single ’ option shift ]
left double “ option [
right double ” option shift [
If you want the French quotes « and » they are option and option shift |
Peter

Can't switch between fill and outline.

Here's the problem: I'm on an iMac, new, trying to use illustrator CS5. after using CS3 for a few years. In CS5, if I draw a shape, flat, in the illustration, then try to give it an outline, or change the outline, or do anything with the outline, I can't. If I click on the Shape tools in the toolbox and draw out an oval, for example, I can switch between outline and fill without any problems. Select shape, go to toolbox, select curved arrow for switching from one to the other. That's it. But if I draw a freehand shape, then try it, i can't do it. THIS IS A BIG CHANGE FROM PREVIOUS VERSIONS OF THE APP. GET IT? What is the problem? If it's something I have done, fine, tell me and I'll fix it. I tried calling Adobe support in Bangalore, and it took 30 minutes just to get the problem thoroughly appreciated by the techies. They just couldn't get the idea for half an hour! I had to go over it 4 or 5 times. And they couldn't come up with an answer. they were no help at all. I'm hoping the forum will yield better results. This is pathetic, guys. Your 90-day tech support is a worthless piece of crap, guys. The only tech support we have is this catch-as-catch-can forum. I've been using Illustrator since 1987, (illustrator 88) believe it or not, it's true. And I've always been able to get tech support to cure the ills. Not any more. Is that the way Adobe plans to offer tech support? if there were a way to contact Adobe Tech Support by going around Adobe Bangalore, i would use it. But, alas, I am stuck with this.

Dear Monika and Mylenium: I figured out part of the problem, but not the solution: The shape I had drawn -and coudn't switch between fil and stroke on-is one I had already done a gradient mesh on, too. I had later abandoned the gradient mesh by using the option key to delete mesh lines, but that didn't take the shape all the way back to its original flat state. So it wasn't a plain drawn shape any more. So how do I release the gradient mesh to get back to a flat shape? I'm also having trouble keeping the shapes in RGB or CMYK mode-they keep defaulting back to greyscale. Could that also be a symptom of using gradient mesh? Note: I'm using gradient mesh for the very first time now; I've never used it before. It seems to leave a lot of unexpected baggage behind. I would send a screen shot, but if I start up Grab or Voila, all the AI pallets go away, and that's half the information. So how do I control gradient mesh?

Is it possible to install Lion on the second hard disk on my Mini (2010) Snow Leopard Server, and switch between Lion and Snow Leopard? I like those voices Lion has in speech.

Is it possible to install Lion on the second hard disk on my Mini (2010) Snow Leopard Server, and switch between Lion and Snow Leopard? I like those voices Lion has in speech.

When baltwosaid NO emphatically, that was described as CORRECT ANSWER. Ditto in the caeses of the radically different answers from Camelotand Matt Clifton
Could it be that CORRECT ANSWER needs better defining by Apple?
That apart, yes, switching might involve rebooting. About the voices, well, I was the other day adding voice to a commentary in a video I was working on. There's only American English accent in SL — Lion I believe has British ones as well.
Why not, I wondered, try to install Lion purely for academic interest, maybe with an SD card (Sandisk Ultra II, 16GB) as Tom Nelson says is possible at http://macs.about.com/od/macoperatingsystems/ss/Perform-A-Clean-Install-Of-Os-X- Lion-On-Your-Mac.htm

JSF / Switch between HTTP and HTTPS

Hello!
I want to switch between HTTP and HTTPS using JSF.
Under Apache Struts framework I can use struts extension "sslext.jar" to configure switching between http and https in one web application.
e.g. Login-jsp should be secured, all other jsp's should run unsecured.
Any ideas?
regards
Harald.

Thanks,
I made the necessary enhancement for the second phase, password confirmation required when return to SSL zone after leaving it after a succesful login.
I did the following:
1) create a class in the application scope and/or singleton class with the servlet paths that require SSL
2) create a plugin that reads ActionConfigs from the ModuleConfig
3) create a filter that sets a request scope flag that says that password must re-entered.
Code Extracts:
1) MainshopContainer application level parameter singleton class:
private static HashMap sslZoneMap = new HashMap(50); // key = servlet path of request, example /login.do
public boolean isInSSLZone(String servletPath)
return this.sslZoneMap.containsKey(servletPath);
public void addToSSLZone(String servletPath)
this.sslZoneMap.put(servletPath,null);
public int getNumberOfActionsInSSLZone()
return this.sslZoneMap.size();
2) Struts plugin
add a call to loadSSLZoneMap in plugin init method:
loadSSLZoneMap(config, mainshopContainer);
private void loadSSLZoneMap(ModuleConfig config, MainshopContainer mainshopContainer)
throws ServletException
try {
ActionConfig[] actionConfigs = config.findActionConfigs();
for (int i = 0; i < actionConfigs.length; i++)
if (actionConfigs.getParameter().indexOf("/jsp/account/") < 0) // /account/* = URL path for SSL zone
// not found = not ssl zone
System.out.println("loadSSLZoneMap, following actionConfigs excluded from SSL Zone: "+actionConfigs[i].getPath());
else
// found = ssl zone
String servletPath = actionConfigs[i].getPath()+".do";
mainshopContainer.addToSSLZone(servletPath);
System.out.println("loadSSLZoneMap, following servletPath added to SSL Zone: "+servletPath);
System.out.println("loadSSLZoneMap, number of actions in SSL Zone: "+mainshopContainer.getNumberOfActionsInSSLZone());
catch (Exception ex)
ex.printStackTrace();
throw new ServletException("Exception caught in loadSSLZoneMap: "+ex.toString()+" Initialization aborted.",ex);
3)
public void doFilter(ServletRequest request, ServletResponse response, FilterChain chain)
throws IOException, ServletException {
HttpServletRequest req = (HttpServletRequest) request;
HttpServletResponse res = (HttpServletResponse) response;
String servletPath = req.getServletPath();
boolean secure= this.mainshopContainer.isInSSLZone(servletPath);
The wole picture:
The filter adds a RequestDTO object that includes all request parameters, one of them is the secure flag.
I have a session scope class UserContainer that includes all the session parameters, one of them is the lastRequestDTO.(last made request)
At the end of all my jsp's I set the lastRequestDTO variable.
In that method I set the passwordConfirmationRequired flag if needed:
public void setLastRequestDTO(RequestDTO _lastRequestDTO)
if (this.lastRequestDTO != null && this.lastRequestDTO.isSecure() != _lastRequestDTO.isSecure())
this.setPasswordConfirmationRequired(true);
this.lastRequestDTO = _lastRequestDTO;
I read the passwordConfirmationRequired in all my jsp's in the SSL zone that allow editing or deleting and if that flag is true, a valid password must be re-entered in order to make the updates.
When the password is OK I reset the passwordConfirmationRequired to false.
I need some help for the first phase, that is SSL setup for all actions related to jsp's with url path /account/*
I tought I could define it in the web.xml:
<security-constraint>
<web-resource-collection>
<web-resource-name>All Account Related Pages</web-resource-name>
<url-pattern>/account/*</url-pattern>
</web-resource-collection>
<user-data-constraint>
<transport-guarantee>CONFIDENTIAL</transport-guarantee>
</user-data-constraint>
</security-constraint>
but that doesn't work and finnaly understood why:
Example: /WEB-INF/jsp/account/login.jsp corresponds to /login.do
The url pattern /account/* at the container level is never encountered.
Is it allowed to declare the following action path: /account/login instead of /login?
If yes I could add following prefix /account to all my action paths and forward paths and this could resolve my problem.
What's your opinion?
If no, would your library resolve this?
Will all the Struts/JSP/JSTL url generating tags pick-up the required protocol (http/https) according to your configuration file?
Regards
Fred

Is there an easy way to switch between ehternet and wifi connection without having to disconnect the ethernet cable?

Hi All
Was wondering if there is an easy way to switch between ethernet and wifi connection on Apple TV without having to disconnect the ethernet cable. The reason I ask is that I find it quicker to use my ethernet connection via a Netgear Powerline Home Theatre Set-up to stream Trailers and Movies on the Apple TV, however this is no good when connecting directly to my Mac to stream music or TV shows in iTunes, so revert to the wifi connection that I created on my Time Capsule to do this.
Would be handy if Apple TV had a menu option where you could manually change the connection type depending on what you were doing, as per above scenario.
Cheers
Brett

brettfromseabrook wrote:
Hi All
Was wondering if there is an easy way to switch between ethernet and wifi connection on Apple TV without having to disconnect the ethernet cable.
Unfortunately not.

Switching between Design and JSP tabs add code?

I am new to SJSC and I am taking the time to go through all of the little odds & ends of the IDE.
I was looking at:
http://blogs.sun.com/roller/page/tor?entry=computing_html_on_the_fly
And I decided to try this.
When I add the following in the JSP tab:
<h:outputText binding="#{Page1.tableHtml}" id="outputText1"/>Save.
Then click on the Design tab, then go back to the JSP tab, I now have:
<h:outputText binding="#{Page1.tableHtml}" id="outputText1"/>
<h:outputText binding="#{Page1.outputText1}" id="outputText1"/>It's late here, but this doesn't make any sense, why would switching between Design and JSP tabs add code?
Thanks,
--Todd

Girish: I followed these steps:
1.) Downloaded:
Sun Java Studio Creator 2, Multilanguage creator-2-windows-ml.exe 254.23 MB
2.) When I started the install, I received the message:
Welcome to Sun Java(TM) Studio Creator 2! You are installing: Sun Java Studio Creator 2 development environment Sun Java System Application Server Platform Edition 8.1 2005Q1 Update Release 2 Bundled database
3.) Installed version:
Product Version: Java Studio Creator 2 (Build 060120)
IDE Versioning: IDE/1 spec=5.9.1.1 impl=060120
Also, Under, the Palette window: Standard component list, there is a component labeled Output Text.
When placed on a jsp, the following code is produced:
<h:outputText binding="#{Page1.outputText1}" id="outputText1" style="position: absolute; left: 24px; top: 48px"/>Thanks,
--Todd

Digital waveform graph switch between hex and binary possible?

Similar Messages

Maybe you are looking for