Direct Connection Between OSX and Ubuntu (Jaunty)

Hello:
I Bought my MacBook a few weeks ago and i want to transfer some information from my pc, which runs Ubuntu Jaunty. What should i do?
Thank you

Jarojasag wrote:
Hello:
I Bought my MacBook a few weeks ago and i want to transfer some information from my pc, which runs Ubuntu Jaunty. What should i do?
yo can do it via an external drive formatted FAT so both systems can read and write to it. or yo can use file sharing and connect the computers via smb or afp.
they need to be on the same local network. don't know how file sharing works in Ubuntu but on a Mac you need to go to system preferences->sharing and enable file sharing.
Thank you

Similar Messages

Direct connection between 2 clients without any configuration!

I wan to make a system act like hamachi or logmein (websever & clients).
I have a webserver on the internet and two client from different networks connected to this webserver, now i want to make directly connection between these clients without any configuration on router. I think it is possible because all infomation about clients network could be got from http request which they send to server. But i don't know what exact fields in the header of http request that i need and how to set them to create connection between clients. I need some ideas about this issue.
Edited by: tulous on Nov 20, 2008 7:40 PM
Edited by: tulous on Nov 20, 2008 7:41 PM

tulous wrote:
I know, so if you want to use a remote control tool such as: VNC, remote desktop you must config on router or server. But even if you had a proxy(permit port 80) when you type www.sun.com you will get data from it, this data was sent from Sun to your proxy and in some way the data was return to your browser. So i think if we have enough information(it come from the webserver) we could init a connection between 2 client. An example of this is Hamachi.
At first 2 hamachi clients connect to a server of hamachi, when they have their id, a tunnel between 2 clients was established without any configuration on proxy(certainly that server did not deny port of hamachi). From now 2 clients can exchange data not through the server. The same in logmein, you can remote desktop any where with zero configuration, but the speed is guarantee because they contact to server for query information, but the data was transmited directly. Sorry if i make mistake.It doesn't work the way you think.
There is a proxy or you have to have one side listening with a ServerSocket and have ports opened as needed. You can't create a Socket connection on server A between clients B and C and then pass it off to clients B and C and magically they just talk to each other.
It does not work that way. It is impossible to do it that way.

Novice trying to connect between office and home MACs

Advice for system novice
trying to connect between office and home MACs
Office MAC OSX 10.2.8 (also runs classic mode)
G4 Computer in the office (only mac in office all others are PC)
I need to connect home computer
IMAC OSX 10.4 Tiger. Connecting via cable modem and have router
I do not have good networking skills, i this something that is doable myself or should I call in a pro?

It's doable.
But at home you need to find the "outside" IP that the Internet sees, not the one you see on that machine.
what's my ip...
http://www.whatsmyip.org/
Then you'll need to "Forward Ports" on the home router so incoming stuff knows where to go.
Then you'll need to enable the Services you wish to use on both machines.

Direct Connection between clients using sockets

Hi, I'm a new user and i have a problem with sockets:
The question is how can i directly connect two users that are already connected to a server in other machine???
I mean
user1 is connected to server
user2 is connected to server
user1 tries to communicate with user1 but don't want to use the server, and the server only provides the client1's ip
I first thought to do this:
user2 asks to server for the info of a client1-server waiting for connections, and i think it could work fine, but only if the ports are not closed by firewall, because client-server will be running in a transparent mode for user and user may not know anything about servers, sockets, ports, etc. the user only will work with a gui or something else and that's all
Does anybody know what can i do to make this possible???
PD
Sorry for my bad English

It can be implemented like you said. Make one of the clients open a serversocket and pass the ip and port number through the server to the other client with information on where to connect.
If you're going to use direct connection between clients a lot then I would recommend that every client open a default serversocket at startup and register that information with the server and then every other client can ask the server for the ip and port to whatever client they wish to open a direct connection to.
Be aware that clients often are behind NATs and firewalls, so if need to deal with those issues you got to use hole punching (http://en.wikipedia.org/wiki/hole_punching) - pref on a known port like 80 - and to deal with the less frequently used application firewalls you can use http encapsulation in addition.

Connection between O and BP is missing

Hi,
When i check inconsistency for a user, i am getting " Connection between "O" and "BP" is missing. When i check the Org.unit in PPOSA_BBP, i could see no BP exists for that Org.unit where user is assigned. I have replicated the org.unit from HR system but yet the BP hasnt been generated. Can you please share your idea on this.
Regards,
Prasath J

Hi Prasath,
This might be because you need to assign the user to a Purchasing Organisation or a Purchasing Group. If the user do not have BP created then you can do this by using tcode USERS_GEN.
Go to USERS_GEN and follow below steps :
1. Select Create User From Existing SU01 user
2. Enter the org id of the POrg or Pgroup under which you want to assign the user
3. Select country and execute
4. In next window one popup will occur, select Area Of User
5. In next popup enter the user id
6. Next select the user and click Ok.
7. This will create a BP and CP for the user and assigns the BP to the Org id of the POrg or Pgroup.
8. Now check the consistency of the user it will show all green.
It might give you error like eMail id for BP XXXXX is missing if the SU01 profile of the user does not contain any user id but it is not critical.
You can open the BP in BP tcode and enter the email id of the user.
Let us know if it solves your issue.
Regards,
Mayur

Can someone please tell me a simple but effective method for burning a slideshow to DVD? Now that the connection between iPhoto and iDVD no longer exists, I can't figure out a way to get there with an acceptable quality result.

Can someone please tell me a simple but effective method for burning a slideshow to DVD? Now that the connection between iPhoto and iDVD no longer exists, I can't figure out a way to get there with an acceptable quality result.

Export the slideshow out of iPhoto as a QT movie file via the Export button in the lower toolbar. Select Size = Medium or Large.
Open iDVD, select a theme and drag the exported QT movie file into the open iDVD window being careful to avoid any drop zones.
Follow this workflow to help assure the best qualty video DVD:
Once you have the project as you want it save it as a disk image via the File ➙ Save as Disk Image menu option. This will separate the encoding process from the burn process.
To check the encoding mount the disk image, launch DVD Player and play it. If it plays OK with DVD Player the encoding is good.
Then burn to disk with Disk Utility or Toast at the slowest speed available (2x-4x) to assure the best burn quality. Always use top quality media: Verbatim, Maxell or Taiyo Yuden DVD-R are the most recommended in these forums.
If iDVD was not preinstalled on your Mac you'll have to obtain it by purchasing a copy of the iLife 09 disk from a 3rd party retailier like Amazon.com: ilife 09: Software or eBay.com. Why, because iDVD (and iWeb) was discontinued by Apple over a year ago.
Why iLife 09 instead of 11?
If you have to purchase an iLife disc in order to obtain the iDVD application remember that the iLife 11 disc only provides themes from iDVD 5-7. The Software Update no longer installs the earlier themes when starting from the iLIfe 11 disk nor do any of the iDVD 7 updaters available from the Apple Downloads website contain them.
Currently the only sure fire way to get all themes is to start with the iLife 09 disc:
This shows the iDVD contents in the iLife 09 disc via Pacifist:
You then can upgrade from iDVD 7.0.3 to iDVD 7.1.2 via the updaters at the Apple Downloads webpage.
OT

Frustration! I have all igoods in order to use all, fully as should be. But looks like Softbank does no agree with any connection between iPhone and iMac... What in the world! How Apple let that happen???

I live in Japan,
I have all igoods in order to use all, fully as should be. But looks like Softbank does no agree with any connection between iPhone and iMac... What in the world! How Apple let that happen??

Make sure that you allow pages to choose their colors and that you haven't enabled High Contrast in the Accessibility settings.
*Firefox > Preferences > Content : Fonts & Colors > Colors : [X] "Allow pages to choose their own colors, instead of my selections above"
See also:
*http://kb.mozillazine.org/Images_or_animations_do_not_load
*https://support.mozilla.org/kb/Images+or+animations+do+not+show

Handoff: No connection between iPad and iPhone

Handoff: No connection between iPad and iPhone (IOS 8).

Hi raydela,
I understand your calls aren't being transferred between devices.
Check out the troubleshooting in this article.
Get help using Continuity with iOS 8
If a call doesn't transfer to your other devices, or you don't see the Handoff icons
Make sure that your devices are using iOS 8 or later by going to Settings > General > Software Update.
Check your settings:
Go to Settings > Wi-Fi and turn on Wi-Fi if necessary.
Go to Settings > Bluetooth and turn on Bluetooth if necessary.
Make sure your iOS devices are connected to the same Wi-Fi network by going to Settings > Wi-Fi and comparing the name of the network each is on.
Go to Settings > General > Handoff & Suggested Apps and turn on Handoff.
Go to Settings > Phone and turn off Wi-Fi Calling.
Best Regards,
Nubz

Bluetooth connection between iphone and ipad no longer workers after upgrade to ver 8 - any help?

bluetooth connection between iphone and ipad no longer workers after upgrade to ver 8 - any help?
I'm trying to use the iphone as a remote with keynote, which again worked before the upgrade

Hi russellpaton,
Thanks for visiting Apple Support Communities.
If your iOS devices are not communicating with each other after updating to iOS 8, the troubleshooting steps in this article can help resolve this sitation as well:
If you can’t use a Bluetooth accessory or car kit
Cheers,
Jeremy

No connection between iPhone and computer

I have No connection between iPhone and computer. Please help me. My iPhone (4s) went nuts a little while ago. Nothing happend when I connected the charger. I had to take out and put it back in again and again and again, between 2-10 times before the charger finally was connected. It's been like this for a while now and a did'nt really have that mutch problem with it. Until today when I tried to sync/backup/restore the whole phone. It started to sync but stoped at the sync of the 5:th app. tried to start over but now my computer can't "find" the phone. It says that the USB-device is not reconizeble.
Please help me.
Sorry for the bad english.

See Here...
Device Not Recognised
http://support.apple.com/kb/TS1538
And Here
iPhone, iPad, or iPod touch not appearing in iTunes
iPod appears in Windows but not in iTunes
Also, Here...
Unable to Update or Restore
http://support.apple.com/kb/HT1808

ABAP Proxy connection Between PI and SRM for XMLs

Hello Experts,
We are trying to set up ABAP proxy connection between PI 7.1 and SRM so we can send XML from SRM into PI.
Our SRM developer is getting an SLD error (below) and seems like something is not set up right in the SLD. Could you help me out with any kind of blog/documention on setting up an ABAP proxy connection between PI and an ABAP system. Something that talks about what steps we need to take in PI and SRM.
error ...
*We saw the error during debugging. This error is preventing XML output
to be sent to PI.
BBP_BD 002 An SLD system has not been assigned to logical system
Thanks,
Mayur

Thanks all for a quick reply. I also had to take following step to achieve the task.
adding the XI system to the SRM config - SRM Server -->
Technical basic Settings --> Define System Landscape? (also please
associated documentation in that link for XI)
Thanks,
Mayur

Error while creating connection between Java and ABAP

Experts
I am getting the following error message when I am trying to test the connection between JAVA and ABAP systems.
1. The system ID is valid
2. The system was retrieved.
3. The system object represents an SAP system
4. The following parameters are valid: Web AS Protocol (http) Web AS Host Name (s09f71v06.svr.bankone.net:8100)
5. The host name s09f71v06.svr.bankone.net was resolved successfully.
6. The server s09f71v06.svr.bankone.net *could not be pinged* successfully.
I have JAVA and ABAP on the same system. I am trying to establish a connection. I have checked all the settings and they looks fine. I have also pinged from other system to this server and the Ping works fine.
Please do let m eknow where do I need to check for the errros or logs for the above error message.
Appreciate your quick help.
Mahesh

Check the relevant services are test are active on the Backend system through SICF trransaction.
Also make sure that default icm services are running.See note 517484.
More important the connector test in the portal system should work properly,recheck the WAS path etc are correct.
Regards
Ajay

JCo connection between java and ABAP

Hi,
Any pointers for some good material on establishing JCo connection between ABAP and Java to execute ABAP FMs.
Thanks and Regards
Arpita Saxena

Please find following link for your reference.
[http://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/85a483cb-0d01-0010-2990-c5168f01ce8a?quicklink=index&overridelayout=true]

Heterogeneous connection between Oracle and Postgres.

Hi All,
I'm trying to make an heterogeneous connection between Oracle and Postgres since few days but i still having this error : "lost RPC connection".
First of all : I'm using Windows 7, Oracle 10g and PostgreSQL 8.4.
I have done the following operations :
1) Create a System DNS named "PG". (Test connection is OK)
2) Create the file "initPG.ora" in "$ORACLE_HOME/hs/admin" :
# This is a sample agent init file that contains the HS parameters that are
# needed for an ODBC Agent.
# HS init parameters
HS_FDS_CONNECT_INFO = PG
HS_FDS_TRACE_LEVEL = ON
# Environment variables required for the non-Oracle system
#set <envvar>=<value>
3) Configure the file "listener.ora" (in "$ORACLE_HOME/NETWORK/ADMIN") :
SID_LIST_LISTENER =
(SID_LIST =
     (SID_DESC =
(SID_NAME = PLSExtProc)
(ORACLE_HOME = C:\oraclexe\app\oracle\product\10.2.0\server)
(PROGRAM = extproc)
(SID_DESC =
(SID_NAME = CLRExtProc)
(ORACLE_HOME = C:\oraclexe\app\oracle\product\10.2.0\server)
(PROGRAM = extproc)
     (SID_DESC =
(SID_NAME = PG)
(ORACLE_HOME = C:\oraclexe\app\oracle\product\10.2.0\server)
(PROGRAM = hsodbc)
LISTENER =
(DESCRIPTION_LIST =
(DESCRIPTION =
     (ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC_FOR_XE))
(ADDRESS = (PROTOCOL = TCP)(HOST = Cédric-PC)(PORT = 1521))
DEFAULT_SERVICE_LISTENER = (XE)
4) Configure the file "tnsnames.ora" (in "$ORACLE_HOME/NETWORK/ADMIN") :
XE =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = Cédric-PC)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = XE)
PG =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = tcp)(HOST = Cédric-PC)(PORT = 1521))
(CONNECT_DATA =
(SERVICE_NAME = PG)
(HS = OK)
EXTPROC_CONNECTION_DATA =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC_FOR_XE))
(CONNECT_DATA =
(SID = PLSExtProc)
(PRESENTATION = RO)
ORACLR_CONNECTION_DATA =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC_FOR_XE))
(CONNECT_DATA =
(SID = CLRExtProc)
(PRESENTATION = RO)
5) Finally, i create my DB-Link and test it :
CREATE DATABASE LINK "CENTRALE_POSTGRES" CONNECT TO "user_login" IDENTIFIED BY "user_password" USING 'PG';
SELECT * FROM "dual"@CENTRALE_POSTGRES;
I got this error :
ORA-03135 : lost RPC connection.
As you can see, i have activated the trace level (HS_FDS_TRACE_LEVEL = ON), but the directory "$ORACLE_HOME/NETWORK/trace" still empty.
Any ideas ?
Regards

the tnsnames.ora alias PG is wrong - you need to have 2 closing brackets after the SERVICE_NAME so that HS=OK is outside of the CONNECT_DATA like:
PG =
<space>(DESCRIPTION =
<space><space>(ADDRESS = (PROTOCOL = tcp)(HOST = Cédric-PC)(PORT = 1521))
<space><space>(CONNECT_DATA =
<space><space><space>(SERVICE_NAME = PG))
<space><space>(HS = OK)
<space>)
Please be also aware HSODBC up to release 10.2 has been desupported since March 2008 and it was replaced by its follow up product DG4ODBC V11

How to make connection between ASP and Oracle 8i

Dear Helper,
I have a problem about how to make the connection between ASP and
Oracle 8i. If you have this idea, please help me to solve this
problem. Thank You!!!
null

You must install Oracle Objects for OLE.
After this in asp-script you may use following instructions
1)initialization
<%
Set Session("OraSession") =server.CreateObject
("OracleInProcServer.XOraSession")
set Session("OraData") = Session("OraSession").OpenDatabase
("service", "scott/tiger",0)
%>
2)open Dynaset
<%
Set EmpDynaset = Session("OraData").CreateDynaset("select 1 as
f1, 2 as f2 from dual", 0)
%>
3)navigation
<%EmpDynaset.MoveFirst%>
<%EmpDynaset.MoveNext%>
<%EmpDynaset.EOF%>
4) Field access
<%=EmpDynaset.Fields(1).value%>
5) Sql execute
Session("OraData").ExecuteSQL("delete xxx")
Best regards.
null

Direct Connection Between OSX and Ubuntu (Jaunty)

Similar Messages

Maybe you are looking for