Disable 802.11b/g

Can i disable 802.11b/g in my new Time Capsule that supports 802.11ac? Ultimaltely I want to disable all standards under 802.11ac (when iPhone/iPad finally supports it)
I have read old wifi standards slows downs routers/acess points etc.

Can i disable 802.11b/g in my new Time Capsule that supports 802.11ac?
Sorry, but no.
Whlle you could customize and maximize previous versions of the Time Capsule, Apple has "upgraded" things by removing the settings that would allow this in the "new" Time Capsule.

Similar Messages

  • Disabling 802.11b, what issues to coverage?

    Hi All
    I want to soon disable 802.11b support on our AP 1231 with B/G cards. I want this because I don't like to have 802.11b clients connecting and taking down the speed.
    The question now is, how would our signal coverage change if I put 'power local cck 1' on the device?
    Or I would only allow theese rates:
    6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 which are only supported by 802.11g cards.
    Would that change the signal range a lot? Or do you have better ideas to disable 802.11b support?
    Thanks,
    Patrick

    Hi Patrick,
    Here is some info related to disabling 802.11b;
    Q. How can I set the AP so that only IEEE 802.11g clients can connect? I do not want the IEEE 802.11b clients to connect and slow down the wireless network. There is a second, parallel 802.11b network for unsecured clients.
    A. In order for the AP to receive only 802.11g clients, complete these steps in the GUI:
    Go to the Network Interfaces section and click Radio 0-802.11G.
    Click the Settings tab at the top of the Radio 0-802.11G window.
    Choose Disable for these data rates:
    1.0
    2.0
    5.5
    11.0
    Choose Require for all the other data rates. These other data rates are:
    6.0
    9.0
    12.0
    18.0
    24.0
    36.0
    48.0
    54.0
    Click Apply at the bottom of the window.
    From this good doc;
    http://www.cisco.com/en/US/products/hw/wireless/ps430/products_qanda_item09186a008009483e.shtml
    As for coverage; A fundamental rule is that as data rates increase, range decreases. 802.11b uses DSSS to support data rates of 11, 5.5, 2, and 1 Mbps each, with correspondingly longer ranges as the data rates decrease. 802.11g uses OFDM to support data rates of 54, 48, 36, 24, 18, 12, 9, and 6 Mbps each, with correspondingly longer ranges as the data rates decrease. The higher data rates supported by 802.11g result in shorter range than the range supported by the maximum 802.11b data rate. Still, OFDM is a more efficient means of transmission than is DSSS, meaning that at a given range, higher OFDM-based data rates will be supported than DSSS-based data rates (all other things being held constant). That being said your range difference should not be too drastic
    From this superior Cisco doc (Have a look at Table 4 for some good Range approximations);
    http://www.cisco.com/en/US/products/hw/wireless/ps430/products_white_paper09186a00801d61a3.shtml
    Hope this helps!
    Rob

  • WLC 2106 Disable 802.11b

    Hello,
    I am trying to enable more channels in the DCA channel list for 802.11/b/g/n.  However, when i hit apply i get this message:
    "802.11b network needs to be disabled to apply changes to DCA."
    I do not see a spot to disable B. Would this be something i need to do from the CLI?
    THanks!
    Seth

    Hi,
    You ned to disable Radios before doing the above config.. here is the was we do it..
    WLC GUI >> Wireless >> 802.11 B/G/N >> Network >> Disable 802.11B/G network setup
    Now do the required setup and go back to the same place and enable it.. this will do it for you!!
    Lemme know if this answered ur question and please dont forget to rate the usefull posts!!
    Regards
    Surendra

  • WRT300n: disable 802.11b wireless

    Is it possible to administratively disable 802.11b radio on WRT300N?
    The reason is to do not allow 802.11b clients to connect to my router, while 802.11g and 802.11n clients should get access to network.
    Solved!
    Go to Solution.

    You cannot disable just 802.11b wireless...When you open the set up page of your router and click on Wireless see the Network Mode...You can disable all or when it is set to mixed it will enable all...When you select Wireless N Only it will disable Wireless B and Wireless G both...Same when you select Wireless G only(it will disable Wireless B and Wireless N both)...This means that you can have two of the modes disabled but not just one...

  • How to find out how many 802.11b clients are connecting

    Hello
    We got around 70 Cisco AP1231 here in autonomous function.
    They're all equiped with 802.11b/g modules.
    I'd like to soon disable 802.11b here (school), but I should somehow find out how many people are still using 802.11b.
    Any ideas how I could automatically do this?
    I also have a WLSE working here.
    Thanks,
    Patrick

    Whether it is IOS software or vx works software you could view the number of clients by clicking on home tab:summary status page.It would listed in the top of the page.If you are using CLI use the command show dot11 associations statistics in the Prev EXec mode. Refer URL http://www.cisco.com/en/US/products/hw/routers/ps272/products_technical_reference_chapter09186a008022e0e3.html#wp2645138

  • Client got not connection to wlan over wlc 2504 on 802.11b/g

    Hi everybody,
    We are using a wlc 2504 with 7.6.100.0 and AP 1532e.
    I have the strange observacion that only clients with 802.11n (2.4GHz) can connect to the WLAN. Clients thats works only with 802.11b/g, they can't connect to the WLAN. Affected are all machines which want to connect with 802.11b/g.
    This is a MESH WLAN with 5GHz backhaul and 2.4GHz for the user.
    During the debugging found the following:
    *apfMsConnTask_4: May 09 11:44:40.581: 00:1b:77:b4:34:e0 Sending Assoc Response to station on BSSID 18:9c:5d:71:34:50 (status 0) ApVapId 1 Slot 0
    *apfMsConnTask_4: May 09 11:44:40.581: 00:1b:77:b4:34:e0 apfProcessAssocReq (apf_80211.c:8292) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
    *spamApTask6: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Sent 1x initiate message to multi thread task for mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Creating a PKC PMKID Cache entry for station 00:1b:77:b4:34:e0 (RSN 2)
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 0
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Adding BSSID 18:9c:5d:71:34:50 to PMKID cache at index 0 for station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: New PMKID: (16)
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584:      [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Initiating RSN PSK to mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 EAP-PARAM Debug - eap-params for Wlan-Id :1 is disabled - applying Global eap timers and retries
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 dot1x - moving mobile 00:1b:77:b4:34:e0 into Force Auth state
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 EAPOL Header:
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00000000: 02 03 00 5f                                       ..._
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: Including PMKID in M1  (16)
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584:      [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Starting key exchange to mobile 00:1b:77:b4:34:e0, data packets will be dropped
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Allocating EAP Pkt for retransmission to mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.585: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.585: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.585: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.585: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:44:42.649: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:44:42.649: 00:1b:77:b4:34:e0 Retransmit 1 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:44:42.649: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *dot1xMsgTask: May 09 11:44:42.649: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *dot1xMsgTask: May 09 11:44:42.649: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *dot1xMsgTask: May 09 11:44:42.649: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:44:44.649: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:44:44.649: 00:1b:77:b4:34:e0 Retransmit 2 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:44:44.649: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *dot1xMsgTask: May 09 11:44:44.649: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *dot1xMsgTask: May 09 11:44:44.649: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *dot1xMsgTask: May 09 11:44:44.650: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:44:46.649: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Retransmit failure for EAPOL-Key M1 to mobile 00:1b:77:b4:34:e0, retransmit count 3, mscb deauth count 1
    *dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Removing BSSID 18:9c:5d:71:34:50 from PMKID cache of station 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Setting active key cache index 0 ---> 8
    *dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Sent Deauthenticate to mobile on BSSID 18:9c:5d:71:34:50 slot 0(caller 1x_ptsm.c:598)
    *dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
    *dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Deleting the PMK cache when de-authenticating the client.
    *dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Global PMK Cache deletion failed.
    *dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station:  (callerId: 57) in 10 seconds
    *dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Freeing EAP Retransmit Bufer for mobile 00:1b:77:b4:34:e0
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Reassociation received from mobile on BSSID 18:9c:5d:71:34:50
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Global 200 Clients are allowed to AP radio
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Max Client Trap Threshold: 0  cur: 1
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Rf profile 600 Clients are allowed to AP wlan
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 1
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Re-applying interface policy for client
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2202)
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2223)
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 In processSsidIE:4795 setting Central switched to TRUE
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 In processSsidIE:4798 apVapId = 1 and Split Acl Id = 65535
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Applying site-specific Local Bridging override for station 00:1b:77:b4:34:e0 - vapId 1, site 'default-group', interface 'catodos'
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Applying Local Bridging Interface Policy for station 00:1b:77:b4:34:e0 - vlan 1, interface id 12, interface 'catodos'
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 processSsidIE  statusCode is 0 and status is 0
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 processSsidIE  ssid_done_flag is 0 finish_flag is 0
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 STA - rates (8): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 suppRates  statusCode is 0 and gotSuppRatesElement is 1
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 STA - rates (12): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 extSuppRates  statusCode is 0 and gotExtSuppRatesElement is 1
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Processing RSN IE type 48, length 20 for mobile 00:1b:77:b4:34:e0
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Initializing policy
    *apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
    *apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
    *apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 Central switch is TRUE
    *apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 Not Using WMM Compliance code qosCap 00
    *apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 18:9c:5d:71:34:50 vapId 1 apVapId 1 flex-acl-name:
    *apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
    *apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 apfPemAddUser2:session timeout forstation 00:1b:77:b4:34:e0 - Session Tout 1800, apfMsTimeOut '1800' and sessionTimerRunning flag is  0
    *apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station:  (callerId: 49) in 1800 seconds
    *apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 1800
    *apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 Sending Assoc Response to station on BSSID 18:9c:5d:71:34:50 (status 0) ApVapId 1 Slot 0
    *apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 apfProcessAssocReq (apf_80211.c:8292) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
    *spamApTask6: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Sent 1x initiate message to multi thread task for mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Creating a PKC PMKID Cache entry for station 00:1b:77:b4:34:e0 (RSN 2)
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 0
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Adding BSSID 18:9c:5d:71:34:50 to PMKID cache at index 0 for station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: New PMKID: (16)
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087:      [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Initiating RSN PSK to mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 EAP-PARAM Debug - eap-params for Wlan-Id :1 is disabled - applying Global eap timers and retries
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 dot1x - moving mobile 00:1b:77:b4:34:e0 into Force Auth state
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 EAPOL Header:
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00000000: 02 03 00 5f                                       ..._
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: Including PMKID in M1  (16)
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087:      [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Starting key exchange to mobile 00:1b:77:b4:34:e0, data packets will be dropped
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Allocating EAP Pkt for retransmission to mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:44:54.249: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:44:54.249: 00:1b:77:b4:34:e0 Retransmit 1 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:44:54.249: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *dot1xMsgTask: May 09 11:44:54.249: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *dot1xMsgTask: May 09 11:44:54.249: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *dot1xMsgTask: May 09 11:44:54.249: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:44:56.249: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:44:56.249: 00:1b:77:b4:34:e0 Retransmit 2 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:44:56.249: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *dot1xMsgTask: May 09 11:44:56.249: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *dot1xMsgTask: May 09 11:44:56.249: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *dot1xMsgTask: May 09 11:44:56.249: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:44:58.249: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:44:58.249: 00:1b:77:b4:34:e0 Retransmit failure for EAPOL-Key M1 to mobile 00:1b:77:b4:34:e0, retransmit count 3, mscb deauth count 2
    *dot1xMsgTask: May 09 11:44:58.249: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:44:58.249: 00:1b:77:b4:34:e0 Removing BSSID 18:9c:5d:71:34:50 from PMKID cache of station 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:44:58.249: 00:1b:77:b4:34:e0 Setting active key cache index 0 ---> 8
    *dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Sent Deauthenticate to mobile on BSSID 18:9c:5d:71:34:50 slot 0(caller 1x_ptsm.c:598)
    *dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
    *dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Deleting the PMK cache when de-authenticating the client.
    *dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Global PMK Cache deletion failed.
    *dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station:  (callerId: 57) in 10 seconds
    *dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Freeing EAP Retransmit Bufer for mobile 00:1b:77:b4:34:e0
    *apfMsConnTask_4: May 09 11:45:03.768: 00:1b:77:b4:34:e0 Reassociation received from mobile on BSSID 18:9c:5d:71:34:50
    *apfMsConnTask_4: May 09 11:45:03.768: 00:1b:77:b4:34:e0 Global 200 Clients are allowed to AP radio
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Max Client Trap Threshold: 0  cur: 1
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Rf profile 600 Clients are allowed to AP wlan
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 1
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Re-applying interface policy for client
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2202)
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2223)
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 In processSsidIE:4795 setting Central switched to TRUE
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 In processSsidIE:4798 apVapId = 1 and Split Acl Id = 65535
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Applying site-specific Local Bridging override for station 00:1b:77:b4:34:e0 - vapId 1, site 'default-group', interface 'catodos'
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Applying Local Bridging Interface Policy for station 00:1b:77:b4:34:e0 - vlan 1, interface id 12, interface 'catodos'
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 processSsidIE  statusCode is 0 and status is 0
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 processSsidIE  ssid_done_flag is 0 finish_flag is 0
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 STA - rates (8): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 suppRates  statusCode is 0 and gotSuppRatesElement is 1
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 STA - rates (12): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 extSuppRates  statusCode is 0 and gotExtSuppRatesElement is 1
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Processing RSN IE type 48, length 20 for mobile 00:1b:77:b4:34:e0
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Initializing policy
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Central switch is TRUE
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Not Using WMM Compliance code qosCap 00
    *apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 18:9c:5d:71:34:50 vapId 1 apVapId 1 flex-acl-name:
    *apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
    *apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 apfPemAddUser2:session timeout forstation 00:1b:77:b4:34:e0 - Session Tout 1800, apfMsTimeOut '1800' and sessionTimerRunning flag is  0
    *apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station:  (callerId: 49) in 1800 seconds
    *apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 1800
    *apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 Sending Assoc Response to station on BSSID 18:9c:5d:71:34:50 (status 0) ApVapId 1 Slot 0
    *apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 apfProcessAssocReq (apf_80211.c:8292) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
    *spamApTask6: May 09 11:45:03.772: 00:1b:77:b4:34:e0 Sent 1x initiate message to multi thread task for mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Creating a PKC PMKID Cache entry for station 00:1b:77:b4:34:e0 (RSN 2)
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 0
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Adding BSSID 18:9c:5d:71:34:50 to PMKID cache at index 0 for station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: New PMKID: (16)
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773:      [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Initiating RSN PSK to mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 EAP-PARAM Debug - eap-params for Wlan-Id :1 is disabled - applying Global eap timers and retries
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 dot1x - moving mobile 00:1b:77:b4:34:e0 into Force Auth state
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 EAPOL Header:
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00000000: 02 03 00 5f                                       ..._
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: Including PMKID in M1  (16)
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773:      [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Starting key exchange to mobile 00:1b:77:b4:34:e0, data packets will be dropped
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Allocating EAP Pkt for retransmission to mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:45:05.849: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:45:05.849: 00:1b:77:b4:34:e0 Retransmit 1 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:45:05.849: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *dot1xMsgTask: May 09 11:45:05.849: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *dot1xMsgTask: May 09 11:45:05.849: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *dot1xMsgTask: May 09 11:45:05.849: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:45:07.848: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:45:07.849: 00:1b:77:b4:34:e0 Retransmit 2 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:45:07.849: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *dot1xMsgTask: May 09 11:45:07.849: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *dot1xMsgTask: May 09 11:45:07.849: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *dot1xMsgTask: May 09 11:45:07.849: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:45:09.848: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:45:09.849: 00:1b:77:b4:34:e0 Retransmit failure for EAPOL-Key M1 to mobile 00:1b:77:b4:34:e0, retransmit count 3, mscb deauth count 3
    *dot1xMsgTask: May 09 11:45:09.849: 00:1b:77:b4:34:e0 Blacklisting (if enabled) mobile 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:45:09.849: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Change state to START (0) last state 8021X_REQD (3)
    *dot1xMsgTask: May 09 11:45:09.849: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Reached FAILURE: from line 5274
    *dot1xMsgTask: May 09 11:45:09.849: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station:  (callerId: 9) in 10 seconds
    *apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Reassociation received from mobile on BSSID 18:9c:5d:71:34:50
    *apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Global 200 Clients are allowed to AP radio
    *apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Max Client Trap Threshold: 0  cur: 1
    *apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Rf profile 600 Clients are allowed to AP wlan
    *apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 1
    *apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Re-applying interface policy for client
    *apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2202)
    *apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2223)
    *apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
    *apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 In processSsidIE:4795 setting Central switched to TRUE
    *apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 In processSsidIE:4798 apVapId = 1 and Split Acl Id = 65535
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Applying site-specific Local Bridging override for station 00:1b:77:b4:34:e0 - vapId 1, site 'default-group', interface 'catodos'
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Applying Local Bridging Interface Policy for station 00:1b:77:b4:34:e0 - vlan 1, interface id 12, interface 'catodos'
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 processSsidIE  statusCode is 0 and status is 0
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 processSsidIE  ssid_done_flag is 0 finish_flag is 0
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 STA - rates (8): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 suppRates  statusCode is 0 and gotSuppRatesElement is 1
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 STA - rates (12): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 extSuppRates  statusCode is 0 and gotExtSuppRatesElement is 1
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Processing RSN IE type 48, length 20 for mobile 00:1b:77:b4:34:e0
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Initializing policy
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Central switch is TRUE
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Not Using WMM Compliance code qosCap 00
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 18:9c:5d:71:34:50 vapId 1 apVapId 1 flex-acl-name:
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 apfPemAddUser2:session timeout forstation 00:1b:77:b4:34:e0 - Session Tout 1800, apfMsTimeOut '1800' and sessionTimerRunning flag is  0
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station:  (callerId: 49) in 1800 seconds
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 1800
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Sending Assoc Response to station on BSSID 18:9c:5d:71:34:50 (status 0) ApVapId 1 Slot 0
    *apfMsConnTask_4: May 09 11:45:15.691: 00:1b:77:b4:34:e0 apfProcessAssocReq (apf_80211.c:8292) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
    *spamApTask6: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Sent 1x initiate message to multi thread task for mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Creating a PKC PMKID Cache entry for station 00:1b:77:b4:34:e0 (RSN 2)
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Removing BSSID 18:9c:5d:71:34:50 from PMKID cache of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Setting active key cache index 0 ---> 8
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Adding BSSID 18:9c:5d:71:34:50 to PMKID cache at index 0 for station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693: New PMKID: (16)
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693:      [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Initiating RSN PSK to mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 EAP-PARAM Debug - eap-params for Wlan-Id :1 is disabled - applying Global eap timers and retries
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 dot1x - moving mobile 00:1b:77:b4:34:e0 into Force Auth state
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 EAPOL Header:
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00000000: 02 03 00 5f                                       ..._
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: Including PMKID in M1  (16)
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694:      [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Starting key exchange to mobile 00:1b:77:b4:34:e0, data packets will be dropped
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *apfMsConnTask_4: May 09 11:45:15.875: 00:1b:77:b4:34:e0 Reassociation received from mobile on BSSID 18:9c:5d:71:34:50
    *apfMsConnTask_4: May 09 11:45:15.875: 00:1b:77:b4:34:e0 Global 200 Clients are allowed to AP radio
    *apfMsConnTask_4: May 09 11:45:15.875: 00:1b:77:b4:34:e0 Max Client Trap Threshold: 0  cur: 1
    *apfMsConnTask_4: May 09 11:45:15.875: 00:1b:77:b4:34:e0 Rf profile 600 Clients are allowed to AP wlan
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 1
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Re-applying interface policy for client
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2202)
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2223)
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 In processSsidIE:4795 setting Central switched to TRUE
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 In processSsidIE:4798 apVapId = 1 and Split Acl Id = 65535
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Applying site-specific Local Bridging override for station 00:1b:77:b4:34:e0 - vapId 1, site 'default-group', interface 'catodos'
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Applying Local Bridging Interface Policy for station 00:1b:77:b4:34:e0 - vlan 1, interface id 12, interface 'catodos'
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 processSsidIE  statusCode is 0 and status is 0
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 processSsidIE  ssid_done_flag is 0 finish_flag is 0
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 STA - rates (8): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 suppRates  statusCode is 0 and gotSuppRatesElement is 1
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 STA - rates (12): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 extSuppRates  statusCode is 0 and gotExtSuppRatesElement is 1
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Processing RSN IE type 48, length 20 for mobile 00:1b:77:b4:34:e0
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Initializing policy
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Change state to AUTHCHECK (2) last state 8021X_REQD (3)
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Central switch is TRUE
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Not Using WMM Compliance code qosCap 00
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 18:9c:5d:71:34:50 vapId 1 apVapId 1 flex-acl-name:
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
    *apfMsConnTask_4: May 09 11:45:15.877: 00:1b:77:b4:34:e0 apfPemAddUser2:session timeout forstation 00:1b:77:b4:34:e0 - Session Tout 1800, apfMsTimeOut '1800' and sessionTimerRunning flag is  0
    *apfMsConnTask_4: May 09 11:45:15.877: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station:  (callerId: 49) in 1800 seconds
    *apfMsConnTask_4: May 09 11:45:15.877: 00:1b:77:b4:34:e0 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 1800
    *apfMsConnTask_4: May 09 11:45:15.877: 00:1b:77:b4:34:e0 Sending Assoc Response to station on BSSID 18:9c:5d:71:34:50 (status 0) ApVapId 1 Slot 0
    *apfMsConnTask_4: May 09 11:45:15.877: 00:1b:77:b4:34:e0 apfProcessAssocReq (apf_80211.c:8292) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
    *spamApTask6: May 09 11:45:15.878: 00:1b:77:b4:34:e0 Sent 1x initiate message to multi thread task for mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Creating a PKC PMKID Cache entry for station 00:1b:77:b4:34:e0 (RSN 2)
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Removing BSSID 18:9c:5d:71:34:50 from PMKID cache of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Setting active key cache index 0 ---> 8
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Adding BSSID 18:9c:5d:71:34:50 to PMKID cache at index 0 for station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: New PMKID: (16)
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879:      [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Initiating RSN PSK to mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 EAP-PARAM Debug - eap-params for Wlan-Id :1 is disabled - applying Global eap timers and retries
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 dot1x - moving mobile 00:1b:77:b4:34:e0 into Force Auth state
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 EAPOL Header:
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00000000: 02 03 00 5f                                       ..._
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: Including PMKID in M1  (16)
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879:      [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Starting key exchange to mobile 00:1b:77:b4:34:e0, data packets will be dropped
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:45:18.048: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:45:18.049: 00:1b:77:b4:34:e0 Retransmit 1 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:45:18.049: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *dot1xMsgTask: May 09 11:45:18.049: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *dot1xMsgTask: May 09 11:45:18.049: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *dot1xMsgTask: May 09 11:45:18.049: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:45:20.049: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:45:20.049: 00:1b:77:b4:34:e0 Retransmit 2 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:45:20.049: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *dot1xMsgTask: May 09 11:45:20.049: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *dot1xMsgTask: May 09 11:45:20.049: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *dot1xMsgTask: May 09 11:45:20.049: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:45:22.048: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Retransmit failure for EAPOL-Key M1 to mobile 00:1b:77:b4:34:e0, retransmit count 3, mscb deauth count 0
    *dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Removing BSSID 18:9c:5d:71:34:50 from PMKID cache of station 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Setting active key cache index 0 ---> 8
    *dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Sent Deauthenticate to mobile on BSSID 18:9c:5d:71:34:50 slot 0(caller 1x_ptsm.c:598)
    *dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
    *dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Deleting the PMK cache when de-authenticating the client.
    *dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Global PMK Cache deletion failed.
    *dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station:  (callerId: 57) in 10 seconds
    *dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Freeing EAP Retransmit Bufer for mobile 00:1b:77:b4:34:e0
    *osapiBsnTimer: May 09 11:45:32.048: 00:1b:77:b4:34:e0 apfMsExpireCallback (apf_ms.c:625) Expiring Mobile!
    *apfReceiveTask: May 09 11:45:32.049: 00:1b:77:b4:34:e0 apfMsExpireMobileStation (apf_ms.c:6632) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Disassociated
    *apfReceiveTask: May 09 11:45:32.049: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station:  (callerId: 45) in 10 seconds
    Thanks for any advice

    In some of the big name brands of wireless, there is "no such thing" as 802.11n on a 2.4 Ghz.  No such thing because Cisco won't allow you (any more) to do channel bonding of 2.4 Ghz.  It doesn't make any sense to bond an already restricted 2.4 Ghz non-overlapping channel (three) and squeeze this number down to two.  
    Can you check to ensure that the data rates for 802.11b are enabled?  Maybe someone disabled data rates from 1 Mbps to 11 Mbps.

  • Photosmart C7250 wireless 802.11b fails

    My new C7250 works well with USB and wired ethernet, but fails miserably (prints slowly, if at all) on my wireless 802.11b network.  All other devices work well on my wireless network.  I've spent many hours with HP and exhausted their first line support.  They supposedly have opened a case but I have heard nothing in a week.  Meanwhile, I took a network trace using WireShark and it shows a large number of retransmissions.  (I'm expert with application/network performance profiling.)  All you have to do is browse to http://192.168.1.xxx/ to test transmission -- don't even need to install drivers or printers to see the errors.  This problem appears to be with wireless support on the C7250.
    Has anyone experienced problems or success with 802.11b on this device?  How about 802.11g?  I would be willing to upgrade my wireless if I knew that it would resolve the problem.
    What does it take to escalate a probem with HP for resolution?

    All 2004 and newer wireless HP Inkjet printers are compatible with 802.11g and 802.11b networks (otherwise we couldn't get 802.11g Wi-Fi certification).  Besides testing for interoperability, we test for a minimum wireless throughput at the TCP layer.
    I'd like to see the internal connectivity report that you can generate by pressing the <setup> and <#> buttons simultaneously.  Scan the report to a memory card, copy it to your PC and post the image here.
    It will tell me information about your wireless network and other networks in the area.
    I have a couple of other questions:
    Does the slow printing go away after a power cycling the printer and then does it return later?
    Does the slow printing go away after a power cycling the wireless-router and then does it return later?
    Are you seeing retransmissions of TCP, 802.3 (ethernet) frames or 802.11 frames?  I wasn't sure at what layer you are sniffing the data at?
    What make and model 802.11b wireless-router are you using?
    Do you have encryption enabled?  Does disabling encryption change the speed of printing?
    How many wireless PC's (Macs?) to you have on your network?  Do they all exhibit slow printing?
    Have you changed the default fragmentation settings of your wireless-router?
    At home, I routinely get 1.5 Mbytes/sec transfer rates between my 802.11g wireless-routers and my HP printers and about 700 Kbytes/sec in 802.11b mode.
    One other thing you can try is to go to the printers internal web page, browse over to the Networking, Wireless, Advanced page and enable the configuration "In an infrastructure network use 802.11b behavior".
    Regards / Jim B
    Regards / Jim B / Wireless Enthusiasts
    ( While I'm an embedded wireless systems engineer at work, on this forum I do not represent my former employer, Hewlett-Packard, or my current employer, Microsoft )
    + Click the White Kudos star on the left as a way to say "thank you" for helpful posts.

  • Disabling 802.11 b clients on a 5508 WLC version 7.0.116.0

    Hi,
    We have a rquirment to disable WLAN access to B clients. I believe the best way to do this is to change data rates in -
    Wireless >802.11b/g/n > network > Data Rates
    diable 1,2,5.5 and 11.
    Mandatory 6
    Supported 9,12,18,24,36,48,54
    A suggestion made to me was to untick the box in -
    Wireless >802.11b/g/n > network > 802.11b/g Network Status
    But I believe doing this from my testing disables the 2.4  B/G radio globally all together. Is there any other method for diabling B clients while leaving G clients ont he 2.4 radio  intact?

    You could set 12Mb to Mandatory, I think that would prevent B clients from associating globally.
    But if it is only a specific WLAN that you never want to support B Clients, you could always set that WLAN Radio policy to 802.11G/A only.... (I think that is still an option).   It should allow G/N and A/N clients, but disallow B clients.      I read somewhere that band select wont work if the radio policy is not ALL, so maybe not viable for you if you use band select (or perhaps this has been fixed).
    Either way I think you have several options at your disposal, not just disabling all B rates..... (this this is the easiest approach if you want all B clients gone, and you have coverage to support non 1,2,5.5,11 rates.
    -Wesley Terry

  • Help Enabling 802.11b Support

    Can anyone help? All I want to do is enable 802.11b support on my Cisco 877W. My 802.11g clients can see and attach to it no problems. My 802.11b clients cannot see it at all. I have tried all sorts but nothing has helped. My config looks like this:
    interface Dot11Radio0
    no ip address
    encryption key 1 size 128bit 7 BC48CE99C4E9B683819990D3C1A5 transmit-key
    encryption mode wep mandatory
    ssid *****
    authentication open
    speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0
    48.0 54.0
    station-role root
    no dot11 extension aironet
    bridge-group 1
    bridge-group 1 spanning-disabled
    What do I need to add to make it visible and available to 802.11b clients?
    Many Thanks,
    Matt

    I'd start by defaulting the AP back to factory default, no WEP, no authentication.
    Check to see if the 802.11b clients can connect.
    If all the 802.11b clients are running the same software, check to see that they are up-to-date drivers & client software. If you're using the MS client software (Zero Wireless Config) try a client using the vendor's client software instead.
    If the clients are not eve associating, look at the basic parameters: things like preamble length (legacy default is "long" which is a one meg data rate)
    If you can get the 802.11b client to connect whith all open parameters, then add WEP. Be advised that some clients need the WEP entered as HEX, not ASCII.
    For example ASCII "ABCD" would be "41 42 43 44" in hex ... make sure you're using the same system. IF youre using something like "12345abcde" that can be a valid (but incorrect) hex string when ou really intend for it to be ASCII.
    Also note that leading or training spaces (ASCII 20) are valid characters. Make sure you do not have leading or training spaces in your WEP (unless you really want them there, in whch case, make sure they're there)
    Make sure the Ethernet format is correct: use the Web GUI to set up. Check the parameters on the "Interfaces" page and do not (at least initially) use the "Best throughput" or "Best Range" settings, leave it at "Default Settings"
    If your 802.11b clients are PDAs, bar-code scanners, or other hand-held devices, check that they are at default settings for the standard 802.11b protocols; some use proprietary protocols for better performance or security.
    That's about it for me ... let us know if any of that changes (works / doesn't work, but acting differently / doesn't work, looks the same).
    Good Luck
    Scott

  • Can you disable 802.11g and 802.11a on an Airport Card?

    Does anyone know if there is a way to disable 802.11a and 802.11g functionality on a MacBook Airport card? I have a very old 802.11b access point and the airport card seems to be making it fail. I was hoping that by turning off 802.11g or potentially adjusting some other airport parameters I might be able to keep the AP from crashing. I'm hoping to keep the AP I have because it has an integrated print server which has been great. If there is no way to modify the settings on the airport card, I guess I'll need to upgrade my AP.
    Thanks.
    Macbook   Mac OS X (10.4.8)  

    Well, I should have used the advice I give to everyone else. Even though my wireless router is very old, there was a firmware upgrade for it. Even though the release notes for the firmware said nothing about it fixing a problem with a MacBook, I upgraded to the latest firmware. After a week or so of testing, it seems to have resolved the problem with the AP going dead when the MacBook was using it.

  • AP with 802.11 G Vs clients with 802.11b

    hi
    i've got more access point 1200 series with he 802.11g but the client are 802.11b . Can the client 802.11b connect at the AP with 802.11 G ? Now i don't resolve this problem anche the client 802.11b connect only with the ap 1200 series with 802.11b
    Thanks for all

    > If you disable the "b" data rates, you've pretty much blocked "b" clients.
    A-ha... As i can understand i must disable 1.0, 2.0, 5.5 and 11.0 speed's.
    "To set the 2.4-GHz, 802.11g radio to serve only 802.11g client devices, set any Orthogonal Frequency Division Multiplexing (OFDM) data rate (6, 9, 12, 18, 24, 36, 48, 54) to Basic."(c) Cisco IOS Software Configuration Guide for Cisco Aironet Access Points 12.3(7)JA
    This the same thing as entering `speed throughput ofdm`? Command disables all 802.11B data rates as you recommend.
    > They may be able to respond / attempt association (that all happens at either one or two mbps for either "b" or "g" ... long or short preambles), but since they dont have compatible data rates, they can never connect.
    I know... But, AFAIK, when 802.11G AP "see" 802.11B client in his coverage area AP "downgrades" to 802.11B to allow this client associacion. Your recommedation prevents this, i'm right? Try to understand me, many years i used damn D-Link (my boss love it) but one day i sad "Cisco or on no any kind wireless :E" and now i have dosens AP-1200 with my many questions... All want now i want - is set "G-only" (in dlink's terms) like function...
    Thank you
    P.S. Sorry for my english

  • Config: Airport Basestation(1st gen w/802.11b) + Airport Express + Xbox

    This is the motherload ? for Config./Setup Question:
    Airport Baestation(1st gen w/ 802.11b only) + Airport Express + Xbox
    (Pertaining to: Network Settings, WDS, Airport Admin Utility)
    Network setups (2 possible configurations):
    1).Cable Modem ->(WAN)-> Airport BaseStation <-(LAN) -> Lynx Switch -> MacG4(OS 10.3.3) + XBOX using an Airport Express
    2).Cable Modem ->(WAN)-> Airport BaseStation <-(LAN) -> Lynx Switch -> MacG4(OS 10.3.3) + XBOX using a Logitech Play Link Wireless Network Bridge
    *note with both of these configs. I have only been successful sending my XBox a signal using setup # 2. w/ the Logitech Play Link Wireless Network Bridge.
    To this point: (MacG4)
    I have installed Amaryllis & Kaid for Mac OS X, & followed the Amaryllis Readme Doc.
    I have followed the XLink Quick Start Guide & everthing is a go.
    To this point: (Network/Airport Configs.)
    I factory reset my AE & ran the AE Assistance. I was able to “Set up a new Airport Express”, & see my AE in the Airport Admin Utility, at that point I got a solid green connection.
    Problem:
    However, I was only able to do this when prompted “What would you like to do with your Airport Express” if I chose “Connect to my current network”, but at this point if I were to enable(check) the “Extend the range of my Airport wirless network”, & from my understanding this has to be done. I am not able to finish the setup, I get an error right after I enter in my basestation password.
    Possible contributing factors to problem:
    My password for both my Airport Basestation & Airport Express are the same.
    > BaseStation Config. using Airport Admin Utility
    1).Internet(tab) >connecting using DHCP.
    2).Network(tab) > Distribute IP addresses > I have “Share a single IP address (using DHCP and NAT) enabled, instead of “Share a range of IP addresses (using only DHCP).
    3).WDS(tab) > can’t enable WDS and keep settings active. (i.e. I can enable them, but if I close out & return they are disabled.
    Airport Express Config. using Airport Admin Utility
    1).Airport(tab) > Wireless Mode: “Join an Existing Wireless Network (Wireless Client)
    2).Internet(tab) > Connecting using: “Wireless Network”, and Airport(WDS) is grayed out.
    The only other thing I am curious if it might be causing some issues with my BaseStation is:
    If you navigate to: System Preferences > Sharing > Internet(tab), my internet sharing is turned Off. I noticed a grayed out “Airport Options”, that might become active if I enable Internet Sharing and choose a port to share my connection.
    *I didn’t do this becuase I got the warning “If you turn on this port, your Internet Service provider might terminate service to prevent you disrupting it’s network…yada yada..
    With all that said, I would be extremely appreciative if someone could drop some serious knowledge on me...
    Thx,
    MHP :?:
    Dual 1Ghz G4 2GigsRAM Mac OS X (10.3.3) Airport Baestation(1st gen w/ 802.11b only) + Airport Express

    To extend the range of a wireless network you need WDS and to use WDS you need two Airports:
    AirPort Express and all AirPort Extreme base stations can use WDS. Earlier AirPort base stations can't.
    http://docs.info.apple.com/article.html?artnum=107454

  • Cisco Access Point Configuration to support 802.11b & 802.11g protocol

    How do i Configure access point to support both 802.11b & 802.11g clients on a Cisco 1121G series access point(AIR-AP1121G-A-K9)
    Regards
    Hitesh

    Hi Hitesh,
    Check out this excerpt from the 1121g AP Installation guide section on enabling the 802.11b and 802.11g radios.
    In Cisco IOS Release 12.3(4)JA and later, the access point radios are disabled by default, and there is no default SSID. You must create an SSID and enable the radios before the access point will allow wireless associations from other devices. These changes to the default configuration improve the security of newly installed access points. Refer to the "Configuring Basic Security Settings" section for instructions on configuring the SSID.
    In Cisco IOS Release 12.3(2)JA or earlier, the access point radio is enabled by default, and the default SSID is tsunami.
    To enable the radio interfaces, follow these instructions:
    Step 1 Use your web-browser to access your access point.
    Step 2 When the Summary Status page displays, click Network Interfaces > Radio0-802.11B or Radio0-802.11G and the radio status page displays.
    Step 3 Click Settings and the radio settings page displays
    Step 4 Click Enable in the Enable Radio field.
    Step 5 Click Apply.
    Here is a link to the actual document:
    http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_installation_guide_chapter09186a00804d2b73.html
    Hope this helps!
    Rob
    Please remember to rate helpful posts....

  • Disable 802.11n - Force MacBook to use 802.11g

    Hello Everyone,
    I'm searching for a possibilty to disable 802.11n on my MacBook. I want it to use the G standard instead.
    We are using a NETGEAR wn802Tv2 Accesspoint in our office. I can connect to the Router, if the Router is in bg-mode. But connection fails when I try to connect, when the router is in ng-mode. Snow Leopard sys the password is wrong. But it is correct.
    I'm not allowed to change the Accesspoint permantly to bg-mode. So I need a possibility to force my MacBook to operate in 802.11g mode.
    Im using Snow Leopard 10.6.2 on the new Uniboy MacBook.
    Thanks in Advance
    Zoidberg

    There is no way I am aware of in Mac OS X to force an 802.11n-capable AirPort card to only use 802.11b/g mode.

  • MacBook loses 802.11b reception

    Hello,
    since two days, I have a very odd problem with my macbook: after a system crash (computer fell too deep asleep while I was not watching), 802.11b (Airport non-extreme) is hardly working anymore. To be precise:
    - connecting the macbook to a 802.11b basestation, or a 802.11b Computer-Computer network works only within 20 cm, and even then it drops the connection every minute
    - connection to a 802.11g (Airport Extreme) network is flawless
    - the networks are fine; all other computers work ok, as before
    Since 802.11b also used to work fine (for a month), I narrowed the issue down to two possibilities:
    - the Airport card has two antennas, maybe there's a hardware issue that would only affect the b mode?
    - the Airport driver could be somehow messed up, or the card's non-volatile memory (PRAM) in a strange state
    I tried installing older drivers (with Pacifist); no change. I reset all things I could imagine (PMU, PRAM, prefs etc.); no change.
    Does anyone know how to reset the AIrport card itself? Or have a different idea?
    thanks!
    Niels
    MacBook 1.8   Mac OS X (10.4.8)   SMC 1.1 installed

    Hi, in fact, disabling the WEP was one of the first things I tried, and for my MacBook and Lucent 802.11b (Orinoco Silver based) basestation (which is by the way compatible with Airport Admin Utility), this doesn't help at all. Security or not, inside about 15 inches of the basestation I get perfect reception (85 with 0 noise on iStumbler), further away it is just gone altogether.
    When I use another 802.11b mac as virtual basestation, it's the same thing: the network isn't even seen at a meter away. When I use an Airport Extreme based computer as basestation everything is as smooth as you could want, WEP, WPA or no security at all.
    I stick to my analysis that somehow the 802.11b is in a funny state on the MacBook Athereos Airport card, and I'm optimistic that some kind of software reset of the card would bring back full functionality. If only we would know how to do this, or Apple would release a patch!
    thanks for all replies,
    Niels

Maybe you are looking for

  • Arabic Language aliases issue in Web Analysis reports

    Dears, I'm using Web Analysis to build reports with aliases in Arabic language. Aliases appear as small squares. Is there any configuration or workarounds should I do to solve this issue? Thanks. Regards, Ahmad.

  • Cant log in to youtube

    I'm not able to log into youtube using my ipad.. i can log in on the web - I suspect it has to do with the fact that I'm using 2 factor authentication .. has anyone successfully used this and have any suggestions? thanks. John H.

  • IPad as modem

    HI , How to use iPad  3G Internet with MacBook Air to connect Internet ?

  • MAC CS3 doesn't have the Transitions available in PC CS3

    I switched to a MAC and because my project was in mid-stream, I bought Creative Suite 3 to finish the project. On the PC version of Premiere, I used the Zoom, GPU Sphere, GPU Page Curl, Slide Swirl and other transitions that are missing in the MAC ve

  • Running totals at the footer of the report

    I want to create running totals but print them not in e.g. in a group footer. All totals should be printed at the end of the report. The number of needed running totals is not defined before, it depends on the number of different grouping criterias: