Disable Audio on E350IA-E45

Hello, 
I'm buying a new mainboard the MSI E350IA-E45 and I would like to know if it is possible to disable the internal audio on this mainboard , I would like to use and external audio card. 
I tried to check in the manual that I download from website but I'm not finding nothing about it. 
Please could help me ? 
Thanks 
Marco

ok, thanks! 
Ciao
Marco

Similar Messages

  • MSI E350IA-E45 boot/post problem with some USB devices

    Hi,
    My new mainboard E350IA-E45 with BIOS ver. 1.4 has problems "BIOS problems" booting/posting when I connect a USB IR Receiver from CyberLink and also with a USB wireless adapter model USB-N10 from ASUS, using USB 2.0 or USB 3.0 ports.
    It does the problem with one of the two devices or the two at the same time connected.
    With the Logo disabled, I only see a number (not always the same) at the bottom right of the screen when I boot/reboot, and I cannot enter BIOS. If I wait a while, about half a minute Windows starts and other times not ( I'm not sure at this moment).
    When this happens (not booting/posting) if I remove (while powered) these devices the motherboard posts immediately and normal operation is back !
    When none is connected, it works without problems.
    Does anyone have a solution or explanation for this behavior ?
    Thanks in advance for any help.

    Quote from: Bas on 13-October-11, 15:28:28
    How can you call this explanation "working fine" ??
    Your powersupply is just 75W, anything can happen with so little power.
    As said before, test the board with a 300W powersupply and see if it solves it.
    I bought this Mini-ITX case to have a silent HTPC, its height is 62mm, so where do I put a power supply of 300W using this case if the problem realy "is" the power adapter ! Sorry to say that, but for me it's not the power adapter.
    When I BOOT it, my power meter indicates the maximum value and it's between 25-30 watts, and you say that a 75W external adapter is not enough and what about netbooks or nettops with Zacate inside with similar adapters !
    Can you explain to me why or how it fails to POST in few seconds (or no POST at all) with one of these devices that has a tiny power consumption. And why it POST with a external USB HDD ! It makes no sense to me.
    Anyway if there is no solution to this problem (maybe BIOS update), I don't mind very much to wait about 20 seconds until it POST with the two devices connected, because after that I have no other problems.
    Best regards.

  • Gpu core clock low msi e350ia-e45

    I'm been running into a problem while bitcoin mining.
    I noticed that when I moved my MSI e350ia-e45 setup into my computer room that the Mhash/s starts off at 11.2 then drops to 4.3 after a couple of minutes.
    The previous room was about 66F ambient temps, the new room is about 75F.
    I downloaded msi afterburner and noticed that when my Mhash/s drops, my gpu core clock speed drops to 200mhz from 492mhz.
    This happens when the gpu hits 60c-61c.
    I was running catalyst 11.6 and then tried 11.7 with the same problem still.
    I've upgraded the bios to the latest 1.5 and still no fix.
    I've tried disabling cool n quiet in the bios.
    I upgraded my case cooling.
    I added thermal paste(which is why it changes in minutes rather than seconds now).
    Still no luck.
    This is a little bit of a let down as I also own a C-50 based netbook that does not exhibit this behavior.  It will happily run at the 278mhz gpu core clockspeed past 80c.
    The e350 is rated up to 90c so why would it underclock the gpu at 61c?
    My friend has an asus e350 board and in my room it doesn't underclock the gpu.  His runs at a steady 78c in here.
    I can only think that it is a bios issue.
    Any idea's?

    I moved it back to the other room with the lower temps and the issues vanished.  Too bad it can't stay in that room(the ethernet connection to that room travels through the outside and is prone to killing switches/routers/ethernet cards during lightning storms.
    I guess it's not much of an issue,  but the whole reason for buying an e350 was the higher gpu clock rate compared to the c-50.  It's kind of pointless if the gpu drops down to 200mhz when slightly heated.  It makes my c-50 netbook much faster than the msi e350 motherboard.
    I love the  motherboard, and all it's features,  except for the clock problem.
    I'm still hoping it's a software issue and not a bios issue. 
    I'll try installing an even earlier version of catalyst.
    I will be installing linux to see if the problems persist.

  • How do I disable audio on a pdf page when opening a link that also has audio?

    Hi,
    I have a pdf page that has audio that plays when the page is visible. I set the "disable" audio to happen when the page is no longer visible. That works great. However, I have a link on the pdf page that opens an attached pdf page. I specifically want that linked page to open in a new window. It just so happens that the attached page also has audio. I cannot find a way to disable the first audio. As it is now, both audios play at the same time.
    Thanks for any help you can give on this!

    Please repost in the Acrobat Scripting forum.

  • HP G72B60US HDMI to TV Disables audio to Surround

    My audio connection runs from the headphone jack to my Surround receiver.  This works perfectly.  The HDMI cable runs from TV to PC. When I connect the HDMI cable to the Laptop, I get the video signal , but the audio to the surround is cut off.
    What can I do in the PC menu to enable the headphone connection when the HDMI cable is connected?
    This question was solved.
    View Solution.

    I'm answering my own post.  I found in audio devices a (disable audio to Sony TV) while right clicking.
    It now gets the audio from the headphone connection.  Problem solved!

  • No Way to disable audio from Video in Photoshop CS6

    I have a video clip that has an audio track that I want to remove, however it seems that the track specific "mute or unmute audio track" and "Disable Audio Playback" buttons only affect playback inside of Photoshop and do not affect the exported output. Am I missing something or is this the designed effect of these buttons? Is there a way to remove the audio track in the current build of Photoshop CS6 without going to something like Premiere Pro?
    Thank you,
    Brandon Boswell

    Hi Brandon,
    This might help:
    http://forums.adobe.com/message/4328012#4328012

  • T60 disable audio

    I have C-Media in USB port and have my microphone plugged into that.  I have an external mic that I plug into the microphone port.  I have clicked "disable" under HD Max audio (internal audio).  When I use my C-Media, "recorder options" pops up and I click on C-Media.  My problem is that the internal audio is still working.  What do I do to stop the internal audio but use the C-Media?
    Help, Please!

    charlesfrombeverly wrote:
    can i disable audio message in texting or messages
    Sorry no.

  • MSI E350IA-E45 HDDs supported

    Hi,
    I need to know if the board 'E350IA-E45' supports 2TB or 3TB Hard Disk Drives ?
    Thanks.

    Quote
    no reason any 3gb drive should not work if those do
    Dito.

  • MSI E350IA-E45 vs MSI E350IA-E44

    Hi
    I want to buy a mainboard MSI E350IA-E45, but I can find it nowhere.
    Seller's made me offer for MSI E350IA-E44, but there is no information on the net about the model.
    There is no test, no review.
    It seems very similar to E45 acoording to specs.
    Anyone knows differences for this two mobo's ?
    Is it older model ? For other region ?
    regards
        Roger

    Quote from: Henry on 24-January-12, 07:54:54
    So far I can only find the MSI E350IA-E44 on the MSI Malaysia website, the -45 is on all the rest of them. I don't see any difference in specifications & BIOS so it's my guess the only difference would be regional location where they are sold.
    http://www.msi.com/product/mb/E350IA-E45.html#?div=Detail
    http://my.msi.com/product/mb/E350IA-E44.html#?div=Detail
    Thank you for your reply. Yesterday I saw these specs also.
    You've confirmed my assumptions.
    I'll buy E44 and check it
    regards
       Roger
     

  • E350IA-E45 broken down within a month

    Brrr.... within a month I had to send back my E350IA-E45. It has completly broke down (no post)
    Does someone else has same experience?
    Configuration:
    PSU: Be-Quiet Pure Power L7 300W
    Mem: Kingston ValueRam 4 GB, PC3-8500, 1066 MHz, 7, Non-ECC, Single (compatible according MSI-site)

    Mmm BeQuiet PSU are not that bad nowadays
    They are FSP based, and mine do run very silently. But sure it is a group regulated unit. Pure power units are budget-oriented...but for the price they cost, really not that bad. Worst than CX400, equivalent to CX430 I would say.
    I had a Corsair TX650 (first one, seasonic based) that died after ~1 1/2 year, get a replacement, the second one worked fine for ~3 months and then started exhibiting so much ripple that I was no longer able to use my computer. But this time no warranty possible, because I replaced the fan (what a mistake).
    In the same time I have an Antec Nepower 650 Blue (seasonic based), still working fine, and a Seasonic M12 700W, much electronic noise now after ~3 years.

  • KC to disable Audio when LP 8 launches

    Hi, I'm new to LP and know there are KC to disable Audio and other things like AU Scan on launch but for the life of me I can't find them in the manual anymoe. Can anybody point me to where there might be a comprehensive list for launch KC?
    TIA, cheers

    Simply hold CTRL when (or right after) you click on L8 icon. After a while a popup window with question "Disable Core Audio driver?" should show up...

  • Disable Audio With Group Policy ( winXP SP2 & Win7 )

    Hi,
    I need some information for disable
    audio in my net work with GP 
    I have windows server 2008
    tanks

    Hi Khaled,
    We can try disabling Windows Audio service.
    The policy setting to do this:
    Computer Configuration\Policies\Windows Settings\Security Settings\System Services\Windows Audio
    Regarding this question, the following thread can be referred to as reference.
    Block Sund Cart
    http://social.technet.microsoft.com/Forums/windowsserver/de-DE/4d40d1aa-8ced-4322-8171-6384ae682feb/block-sund-cart?forum=winserverGP
    Best regards,
    Frank Shen

  • Disable audio message in texting or messages

    can i disable audio message in texting or messages

    charlesfrombeverly wrote:
    can i disable audio message in texting or messages
    Sorry no.

  • E350IA-E45 Problems

    So I got a E350IA-E45 a few months ago, ran perfectly for a few weeks and then started to blue screen and refused to post.  I thought it was a power supply issue as the one that came with the case was total garbage.  Replaced the power supply and it ran OK for an hour or two then crashed again.  So now I was thinking ram and left it sit for a while not wanting to deal with the headache.
    Came back to it a few days ago, ran a mem test and everything came back OK.
    Tried resetting the bios via the jumper, formating the HD and OS.  So far no real luck.
    The biggest problem is sometimes the computer will boot and let me run things for a little while then crashes and refuses to post.  If I leave it sit for a while, sometimes it will post, others no.  I thought it may be heat related, but the highest temp I was able to record was only 63c on the CPU.  I have tried playing with the USB settings as I read in other posts, as well as turning town the RAM speed.  Nothing seems to work.  The times it crashes the most seems to be when playing or streaming video.  I've tried about 5 diffrent versions of drivers as well and really don't know what to try next.  Can anyone give me any ideas?

    So I was able to try the new cable last night, even tried hooking directly to TV instead of through the receiver.  Computer booted to windows, but as soon as it was done loading... blue screen followed by a refusal to post.  When I was able to get a post, checked temps and highest it got was 54c in bios.  Booted to windows with a VGA monitor and started temp monitoring, everything stayed around there.  So I started streaming some HD off of Netflix, again so far so good.  Decided to leave it over night with a temp log running to see how warm it got.  Came back this morning, computer would not wake from suspend and a hard reboot resulted in failure to post.
    So apparently the problem is not localized to just HDMI as I had originally thought.  Waiting a few to see if I can get it to boot and find out how warm it got before going to sleep last night.

  • [MSI E350IS-E45] Problem with DVD drive

    Hello my friends.
    I just bought this little board to make a HTPC for my daddy and Im getting a hard time with it.
    I installed everything fine and installed windows 7, via USB flashdrive and when i rebooted I tried to put the CD with drivers to finish installation, but whenever i put any cd inside this drive the computer boots.
    If I start the computer with CD inside the drive, it will just hang with a 98 error code down and just wont start the windows.
    The computer have the following parts:
    - Spire PowerCube 300w (http://www.spirecoolers.com/main/product_detail.asp?ProdID=826)
    - MSI E350IS-E45
    - 2x2gb OCZ SIGNATURE DDR3 1333MHZ, configured as 1066mhz.
    - 1x OCZ AGILITY 60GB SSD
    I tried change the sata cable from one place to another. This psu is very good and have enough power to this setup, this psu was tested with a core i3 system (wich by the way consumes way more power than this HUDSON guy).
    Please, dont lie to me... Im on this busines for almos 2 decades and I know that there is something very odd happening here, I just downloaded a new bios version and will try to do a bios update later when i get home to see if this problem is solved.
    Thanx in advance!

    First of all, I would redo the cooler paste.
    It's my experience that the installed thermal-pads are no good.
    I have the E350IA-E45 myself and I removed the pads and the temperature dropped significantly.
    I informed MSI about this and they are currently retesting the cooling solution, removing the pads for grease can lower temps as much as 10C!! (or more)...
    As for the PSU, my system with 4! 1TB harddisks and full load hardly uses more then 55W tops, that PSU should not be a problem.
    However, do consider the drive can be faileing, OR the drive is bootable and crashes before Windows can start.
    I have noticed that our Forum-flasher crashes too with exactly the same symptom.
    Anyway, what do you mean the computer boots if you put a CD in? Is that after or before Windows is loaded?
    Because before it can mean the CD is bootable, if it's after Windows is loaded it probably means the drive is bad.
    In any case, do check the thermal pad under the cooler, see in the BIOS how hot the CPU is.

Maybe you are looking for

  • Stopping some family members using my internet!!!

    my problem, i have a 20 step son i want to stop their access to my internet network, if i change the password on my wifi all he will do is reset it in some way and get back on ( yes he is a clever little so and so ) what i want to know if i bought th

  • Help setting up an HP Laser printer to work via the USB

    I Would like to use my airport extreme as my wifi connection for my HP CP-1025 laser printer. I've tried to get my MacBook Pro retina 13" to see the printer when it is plugged into the USB at the back of my AirPort Extreme ac but I'm unable to get it

  • 1:N Mapping without BPM - Inbound Structure

    Hello, I know that a 1:N Mapping without BPM should be possible with newer releases. I tried to do so and set the occurences in the signature tab of message mapping to 1:N. However the problem I am facing right now is that a new <Messages> element is

  • Function in report query builder

    Hi, It is possible to call a function in the select statement of a report query builder as followed : select my_func() from my_table The function is defined as : create or replace my_func() return vachar2 is v_temp vachar2(100); begin v_temp := 'colu

  • Passing and Retrieving parameters problem...

    Hello, I am very green to Oracle forms builder. I have a multi-form application that I am trying to create a parameter list for on the first form and pass that parameter to a second form via the OPEN_FORM method. I am able to create the parameter, I