Disabling "Beep till the action is completed" in Power Manager

Hi,
I selected the the "beep till the action is completed" checkbox when the lid is closed, and the continuous beeping is starting to annoy me now. I was looking through the on-system help that comes with Power Manager (v3.01a) and it doesn't say how to undo the change. I would like to revert back to the default single beep when the lid is closed.
Any help would be appreciated, thanks.
ThinkPad T400 2767-RV8 Win7 Ultimate x64, ThinkPad T61 7659-AB5 Win7 Home Premium x64

hey tuna91,
that's a bit strange, could you uninstall the 3.64 version and then install version 3.62 which is located below and see if the option returns ?
http://download.lenovo.com/ibmdl/pub/pc/pccbbs/mobiles/8ru410ww.exe
WW Social Media
Important Note: If you need help, post your question in the forum, and include your system type, model number and OS. Do not post your serial number.
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"!
Follow @LenovoForums on Twitter!
Have you checked out the Community Knowledgebase yet?!
How to send a private message? --> Check out this article.

Similar Messages

Is there a way to disable touch on the Helix and get a power management for battery cycles?

As the title describes.
I've been drawing a fair bit on the Helix using photoshop but what to find a way to disable touch. I used to be able to do it on my x220t through the control panel>isd tablet settings. Windows 8 doesn't have that option. Please don't mention palm rejection as it doesn't always work.
Also I'd live to know if there is a battery gauge to show the battery cycle of the helix. I know the battery is in good condition. What i'd like to know is the cycles of both batteries.

So I have found a temp work-around that does the deed. I have been using a lot of autodesk sketch, and its bomb if you don't have to worry about your hand touching the screen while you sketch. Here is how I have been doing it.
WIN+X >> Device Manager >> Human Interface Devices >>
Under this section you will find three USB Drivers installed. I found that if I desable the second USB Driver, then the touch screen stops working, but the Digitizer still works 100%. Just re-enable when you want to use the touch again. I really wish Lenovo had software to take care of this out of the box. But as I said, It works for the time being.

Please help me the registry value of Lenovo Power Manager

Hi everyone, I want to change the Battery Health Mode on my L430 windows 8 but i cannot find the setting in Lenovo Metro App. I know that we can change it in Power Manager on Windows 7, so I think about changing the registry value, and I must have the registry key value of Optimize for Battery Runtime Mode(not the Battery Span mode).
If you don't might, may I have your battery mode and the registry value in the following
HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\Lenovo\PWRMGRV\Data\DualModeBattery
This is my registry value, and it was in Automatic Mode
[HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\Lenovo\PWRMGRV\Data\DualModeBattery]
"Automatic"=dword:00000003
"PercentForSwitchingLifespan"=dword:0000003c
"PercentForSwitchingRuntime"=dword:0000005a
"PercentForBatteryHealthExit"=dword:0000000a
"CountForSwitchingLifespan"=dword:00000000
"CountForSwitchingRuntime"=dword:00000002
"CountForBatteryHealthExit"=dword:00000001
"SearchRangOfLog"=dword:0000000e
"SearchRangOfLogForNonReplaceable"=dword:00000007
"SearchRangOfLogForBatteryHealthEntry"=dword:0000000e
"SearchRangOfLogForBatteryHealthExit"=dword:0000000e
"MinDischargePercent"=dword:00000003
"BatteryHealth"=dword:00000001
Thank you for your help and I'm aprreciate for that

Jurgen,
Are you just getting this error while attempting to verify? Can you successfully deploy the app? This issue looks familiar to an earlier post in this forum and I believe the archive is OK but is anerroneous verify error? If the cmp-resource is defined in sun-ejb-jar.xml then it should be fine and if the resources are correctly configured. The other thing to check is that you have a persistance manager resource defined in domain.xml; i.e.,
<persistence-manager-factory-resource enabled="true" factory-class="com.sun.jdo.spi.persistence.support.sqlstore.impl.PersistenceManagerFactoryImpl" jdbc-resource-jndi-name="jdbc/ejbTutorialDB" jndi-name="jdo/pmf" object-type="user"/>

Automatically optimize for battery lifespan charges the batt to 100% in Power Manager settings

Whats crazy about my system is I did a complete driver update with the lenovo update and I still dont have the option for Automatically optimize for battery lifespan. It never shows in my options please someone help me to get this option so I wont burn out my battery. Here is the link to my screen shot http://screencast.com/t/aOvXEJfLnmSm thank you

Hi Shaggy2626,
Thank you for the reply!
There are no additional settings for that, only thing we have to check with setting the BIOS to factory default. To proceed with that go to BIOS and press F9 to set factory default setting and F10 to save and exit.
Uninstall the current version which you have installed and download the application from the below link, it might be little older version. But I have checked with my T430 and its working fine for me.
http://download.lenovo.com/ibmdl/pub/pc/pccbbs/mobiles/n14u403w.exe
Hope this helps!!!
Do post us back if the issue still persists.
Best regards,
Hemanth Kumar
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Where is the Virtual Network Manager in my Hyper-V under Action in my Hyper-V Manager

Hi there - I would not say I am a novice at creating environment within Hyper-V. I have built or should I say created, and then deleted several virtual environments. I am familiar with the process of creating virtual hard disks, virtual machines and then
selecting the appropriate switch etc.
To make a long story short I was having issues connecting my servers this time around. Worked fine the last time I built this same environment. I was researching various blogs and TechNet articles and they mention a "Virtual Network Manager."
I do not see it on my first laptop. I have other selections under the "Action" menu in my Hyper-Manager window but not a Virtual Network Manager. Went to my second laptop and that feature was missing on my second laptop too.
Where or how do I see it?
Thanks
Peter

Hi Peter,
"Virtual Network Manager" is used in 2008/R2 hyper-v .
In 2012/R2 it is named "virtual switch manager" .
They are a wizard to create/manager virtual switch .
Best Regards,
Elton Ji
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected] .

"Undock action" option is missing in Power Manager

I have:
- Lenovo ThinkPad X220
- Windows 7
- All updates from Microsoft and Lenovo are installed to this day 3.11.2011
In the Power Manager 3.64 under Global Power Settings I cannot see the "undock action" configuration option. I need to set Undock action to Standby or Hibernate
Note: the same (installation.exe) of Power manager 3.62 on my Lenovo ThinkPad R61 has undock action option by default.
Thanks in advance

hey tuna91,
that's a bit strange, could you uninstall the 3.64 version and then install version 3.62 which is located below and see if the option returns ?
http://download.lenovo.com/ibmdl/pub/pc/pccbbs/mobiles/8ru410ww.exe
WW Social Media
Important Note: If you need help, post your question in the forum, and include your system type, model number and OS. Do not post your serial number.
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"!
Follow @LenovoForums on Twitter!
Have you checked out the Community Knowledgebase yet?!
How to send a private message? --> Check out this article.

Disabling the button till the response comes

hi all
i want the button to be disabled till the response has finished on clicking the button. Can anyone help how to do it.
in java script it can be done, but it is painful for doing each and every form. so i want a centralized way for doing it.
will the submit button help? we had lot of problem due to it when the load increased and several false records came due to clicking the button several times when response took a long time to come.
in our project we will normal button and the action is executed using the action attribute.

There is no other way than disabling the button with Javascript after onclick. Just create a simple function which does that and call that function in the onclick attribute.

How to hold save operation till the workflow approvals are completed ?

Hello,
The requirement is that on change of certain fields in customer master , an approval workflow should trigger and only after the chain of approvals is completed the change in customer master should be saved.
If standard provides the field eg in SWEC then its fine but otherwise is the following approach correct ?
1. Find a suitable user exit on save action
2. Determine whether the required field is changed or not using the std change history tables
3. if yes, trigger a custom event for the business object which wud be already linked to workflow.
that way the workflow will be triggered
4. now trigger another custom event in the workflow after all the approvals are completed
5. induce a wait for event for this approval-completed event in the user exit. so that till the time this event is generated, user exit processing is not completed (find if there is function module for wait event OR keep infinite loop)
Is this approach correct because its complete 'home-made' design and doesnt look very good to keep the user exit waiting for entire workflow which mite extend to even several days.
what should be the solution for this ?
thank you
B

Hi:
1. Find a suitable exit or BAdI on save action (even Enhancement point)
2. Check whether the required fields are changed or not, if yes- then display an information message saying, "Approval WF process started for the customer: XXXXX". Then after displaying the information message, system needs to behave like as an error mesaage was showned.
I mean, you need to come out of the current standard screen and the whole std. program (little bit tricky but it is possible to do), so we are not saving the data to database table.
3. Then after all approvals in WF, use std. FM or BAPI to update database tables for the changed data.
Vinoth

Cannot delete exe files - The action can't be completed because the file is open in Windows Explorer

We have received 3 new computers with Windows 8.1. All of us 3 have the same problem: we cannot delete exe files with message "The action can't be completed because the file is open in Windows Explorer"
For example, I download skypeinstall.exe on desktop, install the program correctly and then try to delete the file: file is in use by Windows Explorer, cannot be delete.
We reboot computer, we are able to delete the file. But, if I restore the file from the recycle bin on the desktop, I cannot delete it again until I reboot the PC. I used ProcessExplorer to see what is locking it and I can see 5 instances of explorer.exe
locking the file.
I can always reproduce the same way:
1-Reboot
2-Delete exe file
3-Restore file
4-Delete stop working and 5 explorer.exe handle are locking it.
I have tried the following so far after reading multiple threads:
- De-activating Windows Search service
- Activating User Experience service
- Deleting from command prompt (no success)
- In folder options: inactivate display icon on thumbnail and activate always display icons, never thumbnail
- Changing folder view (contents, detail, small icons...)
- Using Lock Hunter - not working until reboot
None of these worked.
We all have Windows 8.1 with Crucial SSD drive, could the problem be linked with the SSD drive incompatibility?
Any help would be appreciated.

Hi,
Please try to make a clean boot for your system, then check if this problem resolved.
Clean Boot: http://support.microsoft.com/kb/929135
If problem persists, try to open Resource Monitor to check handle of Explorer.exe, if there any exception, end them for test.
Roger Lu
TechNet Community Support

The action could not be completed because of a conflict with the original item. The conflict may have occurred when an existing item was updated on another computer or device. Open the item again and try making your changes. If the problem continues, cont

I have a user on an iMac 10.6 connected to our domain. She uses Outlook web access for email on our exchange server. Last week she received the following message which is randomly preventing her from sending emails. She claims no attachment was involved in the original email when this all started. I have not been able to look at her account as she is out of the office but maybe someone else dealt with this issue. I realize this may not be Mac related but thought I'd give it a try. She did say it occurred once over two days while working on a PC but it continued over the past weekend.
If an internal user tries to send a message with infected attachment using Outlook Web Access, it may report the following error message: The action could not be completed because of a conflict with the original item. The conflict may have occurred when an existing item was updated on another computer or device. Open the item again and try making your changes. If the problem continues, contact technical support for your organization.
This is because F-Secure Anti-Virus for Microsoft Exchange has detected a virus in the attachment. If the user tries to send the message again, the message will be sent but without the attachment. At the same time a blank message with an attachment named "Attachment_information.txt" will remain in the user's Drafts folder. The "Attachment_information.txt" will contain information about the virus detected in the message.

PS - have found other posts indicating that clips smaller than 2s or sometimes 5s, or "short files" can cause this. Modern style editing often uses short takes ! Good grief I cannot believe Apple. Well I deleted a half a dozen short sections and can export, but now of course the video is a ruined piiece of junk and I need to re-do the whole thing, the sound etc. which is basically taking as much time as the original. And each time I re-do it I risk again this lovely error -50 and again trying to figure out what thing bugs it via trial and error instead of a REASONABLE ERROR MESSAGE POINTING TO THE CLIP IT CAN'T PROCESS. What a mess. I HATE this iMovie application - full of BUGS BUGS BUGS which Apple will not fix obviously, since I had this product for a few years and see just hundreds of hits on Google about this error with disappointed users. Such junk I cannot believe I paid money for it and Apple does not support it with fixes !!!
If anyone knows of a GOOD reasonably priced video editing program NOT from APPLE I am still looking for suggestions. I want to do more video in future, but obviously NOT with iMovie !!!

The action cannot be completed. the connection to microsoft exchange is unavailable

Hi dear.
We have exchange 2013 and we want auto configure outlook 2007,2010 and 2013. In first time when we are setup exchange 2013 we can auto
configure outlook. But I don’t know now we cannot configure outlook. I think when we make some change in exchange certificate ( created by exchange in first time ) and after that we cannot configure outlook. Just we can set up pop3 and imap
for outlook. Now we have outlook with pop3 and outlook web app ( OWA ) and we don’t have problem with them, but we want our client see the all contact list in outlook. When we want configure outlook with Microsoft exchange server we get the error “
the action cannot be completed. the connection to Microsoft exchange is unavailable “.please help me. I don’t know how I solve the problem.

hi.
ok. this is the out put of autodiscover url in address bar :
"" <?xml
version="1.0" encoding="utf-8" ?>
- <Autodiscover
xmlns="http://schemas.microsoft.com/exchange/autodiscover/responseschema/2006">
- <Response>
- <Error Time="10:30:23.5154338"
Id="3405091169">
<ErrorCode>600</ErrorCode>
<Message>Invalid Request</Message>
<DebugData
/>
</Error>
</Response>
</Autodiscover> ""
thanks for your help.
If it returns error code 600, your autodiscover service should be accessible in Exchange server. Please restart Microsoft Exchange Address Book service in Exchange server, then create a new Outlook profile in Outlook to have a try.

The action cannot be completed. The connection to Microsoft Exchange is unavailable. outlook must be online or connected to complete this action

I have outlook 2013 and am trying to add an exchange 2010 multi-tenant account.
I have created a new profile.
I select Manual setup or additional server types
Then select Microsoft Exchange Server or compatible service
I enter the server settings. But the following error is returned when i click check name
"The action cannot be completed. The connection to Microsoft Exchange is unavailable. outlook must be online or connected to complete this action"
I have tried selecting more settings, selecting security, and then selecting the option:- Always propt for logon credentials.
But the same error is still returned
I tried deselecting the option Encrypt data between Microsoft outlook and Microsoft Exchange
But still continue to get the same error.
Reading from other forums I have tried restarting the Microsoft Exchange Address book service under services on the exchange server.
But this did not help either
i am able to access the email accout via outlook web access. I am also able to add the email account to my iphone with the server details and it adds fine onto my iphone but cannot add it to outlook 2013.
any help would be appreciated.
Thanks
Rehan Miah

Hi,
This issue may occur when the HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Explorer\User Shell Folders registry key does not contain all of the required data. Specifically, these problems occur if the
AppData string value is missing from this registry key.
NOTE: The \User Shell Folders key also contains a string value called
Local AppDatawhich is different from the value called AppData. The value that causes this problem (if it is missing) is the
AppData value.
To resolve this issue, import the User Shell Folders registry key from a working Windows User Profile.
For more information, please refer:
http://support.microsoft.com/kb/2264398
Hope this helps.
Best Regards,
Steve Fan
TechNet Community Support
I have looked in the registry and Appdata is not missing it has the following value "%USERPROFILE%\AppData\Roaming" also Local AppData is there with the following value "%USERPROFILE%\AppData\Local" i do not have a working machine to import the user shell
folders registry key so any other advice would be useful.
thanks
Rehan Miah
In order to test what you suggested i created a windows 7 virtual machine installed outlook 2003 however i also get the error on the virtual machine that i have created.
any further suggestions would be a great help.

I dropped my iPhone 5 and the screen is completely black and when i plug it into my computer it constantly beeps. When I call it it doesn't go straight to voicemail but my phone doesn't ring. Rebooting it doesn't work. What is the problem?

My screen has been cracked for a while now and today I dropped it and parts of the screen on top came off and the phone went completely black. I tried calling it and it rings as usual on the line but my iphone doesn't make any sound. I just plugged in my phone to my macbook and i am still able to import pictures and send imessages but while it's plugged in my phone constantly beeps..the same beeping as it does when its on the charger but it's just one beep every couple seconds. People have been telling me it could be the LCD..any thoughts?

Ask Verizon.
If you don't know whether you have AppleCare+, you can find out warranty information by entering the serial number at http://selfsolve.apple.com. The serial number can be found under Settings > General > About > Serial Number, if you are still able to use the phone. If not, eject the SIM card tray from the right side of the phone using a paper clip or SIM unlock tool. It is in very tiny print on the rim of the tray.
You cannot purchase AppleCare+ if it's been after 30 days or the phone has already been damaged like yours.

I am using Photoshop CS5 on a new iMac with a wireless keyboard. I used to be able to hit F11 to perform a custom sharpening action but now the F11 key is the volume control key and I have tried everything to disable or switch the volume key. I have also

I am using Photoshop CS5 on a new iMac with a wireless keyboard. I used to be able to hit F11 to perform a custom sharpening action but now the F11 key is the volume control key and I have tried everything to disable or switch the volume key. I have also tried assigning other function keys to initiate the action. Is there a simple solution to this? What am I missing?

Try unmounting the volume on your iMac using Disk Utility. Then mount it again. You may need to reboot the laptop or relaunch its Finder process (using the Force Quit window) after remounting the drive on your iMac. Remember that no process may be accessing any files on the drive you plan to unmount, or the unmount will fail. Unmounting and remounting an external drive on my iMac made it become visible on my MacBook Pro after it had disappeared.

App Catalog ERROR "The action could not be completed. Try again later" Yellow exclamation mark

Hello, I have problem with access to App Catalog, when i try to access to App Catalog it's give error "The action could not be completed. Try again later" with yellow exclamation mark. I tried to make partial erase, I made full erase, I made Secure erase, but all these steps not helps.
I renew my firmware with latest webOSDoctor, but still nothing. Then I changed my Palm Profile, I create new one, but still NOT WORKING!
I checked all connections 3G and Wi-Fi, everything is ok, but App Catalog still not working.
So, I contacted with Palm Support, I told about this issue and I send them Quick Log and Log
with Description to [email protected]
Reference number for chat: Chat session ID number 89786521
Do you have any solution?
Best regards
Rufat Jalilov
Post relates to: Pre 2 p102una (Unlocked NA)

Honestly saying, the problem I had already a week, I tried to solve it on their own, but all my attempts were unsuccessful, I am sure that this problem is not related to what some of my actions, cause I never made any manipulations with phone.
I really appreciate the attention rendered by the support services, I just need that everything works fine.
I am sure that this is some sort of a strange problems, I have long been searching for an answer in the Internet came on similar way problems have other users.
I received today a update notice for App Catalog, I saw that HP Palm updated App Catalog, I updated my App Catalog, check again, but still nothing changed, same problem "The action could not be completed. Try again later" with yellow exclamation mark.
So, I will wait for a few days, will see what's happening.
Best regards
Rufat Jalilov

Disabling "Beep till the action is completed" in Power Manager

Similar Messages

Maybe you are looking for