Disabling Low Rates on a WLC

I was wondering if disabling low rates could cause issues for clients in higher density areas. For example, if I have 9 meg as the minimum allowed rate, what is actually taken under consideration for that rate? If I have a significant number of clients connected to that AP, is that going to be taken under consideration by the controller when calcultating the minimal supported rate to all clients? Or does it only take under consideration the distance between the nearest AP and the client and the obstructions in between?

Mandatory rate is what the client must be able to negotiate at. Supported rate are rates the WLC will allow the client to negotiate to. Disabling the lower data rates only affect old devices that might require 1 or 2 Mbps data rate. Distance from the AP is a factor as what the client and ap negotiate at. In a high density deployment for example, I have had 24mbps as mandatory and everything below 11 or 12 disabled and the rest supported. I might also add another mandatory rate if I'm using multicast. You need to know your RF to really decide what you can have a a mandatory and it supported.
Sent from Cisco Technical Support iPhone App

Similar Messages

Vendor - Tax deduction at lower rate - MIRO & FB60

Hi all,
Currently we are having one issue of u201CTax deduction at lower rateu201D for a Vendor who is having such certificate with him.
For amount purpose we have set the SPRO setting but the user is asking for the date control also since the Vendor is having the relevant certificate till 31.03.2012 and after that, lower rate Tax deduction will not be allowed.
Simple option is to change the Vendor Master with the original tax type+ Tax code (Normal Rate) combination to calculate tax at the normal rate. But if could not cross the amount limit before 31.03.2012 then that will be difficult to keep an eye on date i.e. 31.03.2012 and then change the master data of u201CNu2026u201D No. of Vendors .
We want to put a condition in a system as; system should check the system date with the tax type date to get a date control. We have restricted the date of u201Cnewly created tax typeu201D till 31.03.2012.
In case of MIRO testing, we have use a user exit which is correctly comparing the system date with the tax type date in runtime. If the tax type date is older than system date then system is throwing an error to change the master date (FK02 / XK02) of subject vendor.
In case of FB60 we are facing a problem since not able to cross confirm the tax type date with the system date. We are trying BTE u2013 1140 for FB60 but in runtime we are not able to get the tax related details / tables.
Is there any workaround or way in BTE u2013 1140 for FB60?
Regards,
Shridhar
Edited by: Shridhar Sawant on Nov 2, 2011 2:23 PM

Hi Ramesh,
In the SAP Std. setting of Formula we are maintaining one more line for same TAX TYPE + TAX CODE + COUNTRY combination but for the ending date of lower rate tax deduction.
Since there is no "To date" option in Formula setting, we are maintaining one more line For e.g. in the 1st line we have a date as 01.04.2011 (i.e. Valid from) and in the other line we have mentioned date as 01.01.2012 (i.e. To date) since Vendor is having the lower rate tax deduction certificate uptill 31.12.2011.
In the first line of formula (Valid from 01.04.2011) we have maintain :
To Base amt              W/tax    Reduction base amt.
175,000.00                 3.00               -
9,999,999,999.00     10.00     175,000.00
In the second line (Valid from 01.01.2012) of formula we have maintain :
To Base amt             W/tax    Reduction base amt.
9,999,999,999.00    10.00               -
Cross confirming the various scenarios since date accumulation of tax setting is on in Tax Type that we are considering.
Will confirm to you the change suggest by you.
If these changes doesn't work then we have to go to the option of User exit or BTE for MIRO and FB60 testing.
Have any idea about the above mention settings ?
Regards,
Shridhar

TDS at lower rates for certian limit

Hi experts,
Income Tax Department gives vendors certifcate for lower deduction of
tax u/s 197, which is a permission to a payer to deduct NIL Tax or tax
at a lower rate. This permission is generally given for a Financical
Year. However, recently it is seen that these certificates are for a
certain Limit. eg: a vendor is given a certificate u/s 197 upto a limit
of Rs.10,00,000/- for NIL deduction. This means that as soon as the
payment to this vendor crosses Rs.10,00,000/- TDS is to be deducted at
the normal rates. THIS NEEDS TO BE CONFIGURED IN THE SYSTEM so that the
correct TDS is deducted and paid.
Regards
venkat reddy

Dear Friend
In current Sap scenario it is not possible to have value cap on the withholding tax.
What we are doing is manually keeping tab on the value cap every month and The user is updated with the available limits. Once the cap is reached, the exemption validity date is changed from 31.03.2008 to the date on which the last invoice was posted. Any subsequent invoice attracts WT at full rate.
Somewhat cumbersome particularly in year end when most of the limits are reached but cannot help it.
We had suggested some customisation wherein the exemption percentage would be checked with the accumulated tax base amount but the same was rejected based on cost benefit ratio.
Would appreciate if you could think of something new and share the same.
Regards
Mukesh

Disable low power wake?

Hi everybody,
is there any way to disable low power wake? Unfortunately, it causes a lot of problems, e.g. TeamViewer, Rowmote, EyeTV refuse to work properly after Wake on LAN because the screen is not turned on again. It's a very annoying feature, especially on my Mac mini which I use as HTPC. If there is no fix or no update coming, I will have to go back to Snow Leopard.
Thanks in advance
Steffen

Here the solution:
http://forums.macrumors.com/showthread.php?t=1195152&page=2
you need superuser rights to perform this change.

Low rates of (modulus) breakpoint re-enabling

Hello!
I am using the motion control NI7334 and I need the breakpoint output to trigger my measurements.
In a quite simple program I re-enable the (modulus) breakpoint each time it occurred. The fastest repetition rate I could generate to enable the breakpoint was about 110 Hz, with higher breakpoint frequencies it becomes irregular, means I don't get all breakpoints. I'm worried if it becomes even worse when my program will be more complex. These low rates for re-enabling the breakpoints are a problem of the labview-code, of windows xp or of the communication between software and PCI-board?
Attachments:
motiontest.vi ‏81 KB

The reason why you can't reach faster breakpoint reenable rates is a
mixture of all the reasons that you have suggested plus some internal
delays on the board. There is not much you can do about that.
There are several options for better breakpoint performance:
You could contact your local NI branch to upgrade your NI 7334 to a NI 7354.
The 735x boards provide buffered breakpoints with 2 kHz trigger rate
and periodic breakpoints with 4 MHz. Reenabling is done automatically
on the board.
You could use the counter inputs of a DAQ-board like the PCI-6220 (two counters) or a dedicated counter board like the PCI-6601
(four counters) to generate the trigger signals by dividing down the
frequency of the encoder signals. As this runs in hardware, you will
also be able to generate triggers with rates up to several MHz.
I hope that helps,
Jochen Klier
National Instruments Germany

Saving Data at lower rate

Hi ,
I am acquiring data through DAQ . The sample rate is 20k and sample to read is 2k. These setting satisfies my requirements. But the data that I save is huge since I intend to aquire it for hours. Hence I would appreciate if somone could tell me how to save data at lower rate i.e. without changing the "sample rate" or "sample to read". Moreover if i could set the saving frequency of data each time I start the aqusition.
Thanks in advance for help.
Solved!
Go to Solution.
Attachments:
Data Aq.vi ‏867 KB

I haven't used it, but most of the questions I see regarding logging large amounts of DAQmx data reccomend using TDMS to record data.
There are LabVIEW functions as well as plugins for Excel, OpenOffice and MATLAB for loading TDMS data.
TDMS Direct Integration in NI-DAQmx Logging
The NI TDMS File Format
Now is the right time to use %^<%Y-%m-%dT%H:%M:%S%3uZ>T
If you don't hate time zones, you're not a real programmer.
"You are what you don't automate"
Inplaceness is synonymous with insidiousness

Lower Rate TDS upto certain limit

I have one vendor who is applicable lower rate of TDS upto certain limit, but after certain limit system have to charge normal rate of TDS, is it possible to track and post such type of transaction in SAP?

HI,
It is possible with help of below config.
Accumultion + Formula's
please create separate tax type and tax code for this particular vendor.
tax type
accumulation , per year start month 4
tax code
check box " form w/tax"
Define the formula's for withholding tax.
upto
50000 5%
9999999999999 10 %
above is very specific to one vendor.
Regards
Madhu M

My new airport extreme transmits at low rates (0-54)and is intermittent? Help!

I need help figuring out why my new 6th generation airport extreme signal is transmitting at a low rate (0-54) and when streaming the signal goes in and out? My equipment is as follows... I have a moterolla extreme DOCsis 3.0 modum, comcast 30 mpbs, and new apple extreme with current airport utility 7.7.1. Any ideas or troubleshooting tips?

When you created your wireless network with the Airport Extreme, did you select having your wireless network backwards compatible with "b/g" devices? If your wireless network was created as "N" compatible for "N" compatible wireless cards only, an iPhone will not be able to connect to your wireless network since the iPhone's wireless card is not "N" compatible.

Disable data rate to a specific AP only?

Hello everyone, Im using Cisco 5508 with 7.0.220.0 code and I just wanted to know if its possible to disable some data rates to a specific group of APs and not affect the rest of the APs
Another question is about almost the same thing but related to WLAN Radio Policy. If I enable a specific WLAN to use radio policy 802.11g-only, all the clients using this WLAN can only associate to 802.11g data rates??? are there any other things to consider on about this policy?.
thanks in advance for your time and help!!!!

Rasika is right on... you need to upgrade if you want to use RF Profiles...
Another question is about almost the same thing but related to WLAN Radio Policy. If I enable a specific WLAN to use radio policy 802.11g-only, all the clients using this WLAN can only associate to 802.11g data rates???
> Clients can only connect on the 2.4ghz either 802.11b g or n
are there any other things to consider on about this policy?
> Setting the policies on the WLAN just defines what you want to be able to associate to that WLAN. For example, wireless ip phones you might set it to 5ghz only, so phones have to be able to connect using only the 5ghz. If there were any 2.4ghz device only trying to access that wlan, they wouldn't be able to associate. Another example is like guest ssid... I always only allow then on the 2.4ghz, not on the 5ghz.
Thanks,
Scott
*****Help out other by using the rating system and marking answered questions as "Answered"*****

Disable low battery warning?

Is there a way to disable the low battery warning that pops up at 20% remaining? I turned off Notifications, but that didn't stop the low battery notifications.
I usually have up to two hours to go when the battery is 20%, and dismissing this warning every 10 minutes gets annoying. Plus, there is a battery level indicator on the screen at all times, and it turns red when 20% is reached. So really, this pop-up warning serves no purpose at all. It reminds me of Windows, tbh.

Hello MikeC2010,
And welcome to Apple Discussions!
At this time no.
B-rock

Buffered edge count FIFO overflow even at very low rates

Dear Forums,
I am trying to use a PXI-6608 to timestamp the sample clock of a PXI-4498 during analog input. Because the sample rate will be on the order of 20KHz, I want to use a pulse generation task on one counter to divide it down by a factor of 1000, then use that pulse as the gate and the 10MHz clock on the 6608 as the source in a buffered edge -- I expect about 20 edges per second, which should be very manageable to retrieve over DMA.
The result is that I get error -200279 ("attempting to read samples no longer available") immediately after the vi starts, before I have retrieved even one count.
This is my first stab at using DAQmx for counter/timer instead of the old DAQ drivers, so I'm sure I've done something wrong, but I can't figure out what.
I've attached the vi if that helps.
Thanks!
Cas
Solved!
Go to Solution.
Attachments:
simplified chassis test.vi ‏314 KB

It appears that you have your gate and source backwards. The sample clock should be ctr0internaloutput and the count edges terminal should be the 10 MHz clock. You are getting the buffer overflow error because the FIFO on the card is only 2 samples and at 10 MHz these are being rewritten was faster than a computer could possible pull them off the card.
Doug Farrell
Product Manager - Condition Monitoring
National Instruments
National Instruments Condition Monitoring

Disable low on battery warning for Mighty Mouse?

How do I do this? This is VERY annoying. I've got more than 20% of battery life left, but OSX keeps telling me I need to change batteries! Also, the menu icon keeps placing itself into the menu! I keep on disabling the bluetooth menu item, but it always comes back!! help!

Depending on where the real issue is, in the system, other options may include
performing an "Archive & Install" then upgrade the system using the latest bits.
Since that gives you an option to move user and account settings over to an
all new System Folder, you would only have to find and reinstall anything not
otherwise up to date. Things to include the latest Flash & Shockwave, or any
parts not automatically put into place through the update to the last OS X step.
There are some details in this Archive and Install, plus update, which may be
tedious; while most should be straightforward. No telling if this would fix the
problem, but it should be able to resolve it.
When did this problem begin? Have you replaced the battery in the mouse
more than once since you bought it? (Is the mouse under warranty? To
hope the problem was only in the mouse itself may be optimistic.)
The non-hack answers may be best; since some hacks may later be a
source of a new problem when later system updates are applied. But
not always. Another thing to try, if the mouse battery issue is recently
developing and no direct cause is known, you could get the last OS X
Combo update and see if reapplying it over the current installation may
help; be sure to start up in SafeBoot, then run Disk Utility's 'repair disk
permissions' then quit Disk Utility, and restart normally to get out of the
SafeBoot mode.
Sometimes just going into a computer in Terminal or Single-user and
revalidate the correct and original settings and then exiting, rebooting
into the OS X GUI, may help correct an issue; while changing nothing
except the symptom. Hard to say if that's an answer in this case.
Hopefully someone with more tweaking experience or an issue similar
to your computer's symptoms will reply here and offer another insight.
Sometimes general system and preventative maintenance may help
resolve some odd issues in the system; to include utilities that can
run scripts for you to perform routines often overlooked. ie: OnyX.
Good luck & happy computing!

How do you disable low phone space warning?

I have a Nokia 520. I currently have 3/4 of a GB left. Plenty of room for what I use the phone for. At least once a day I get this warning about low phone space and it wants me to use the SD card. The SD card actually has almost no available space on it.
All I want is for the phone to stop sending me a warning about the low phone space. I haven't found a way to diable it and it is becoming a huge annoyance for me. Is there a way to turn it off or is the phone designed to be a permanently be an annoyance?

if unchecking the "all other notifications" doesn't do it for you in (Settings/ringtones+sounds) it may be reminders.
but if you uncheck reminders, you may not be able to get any other "reminders" like calendar and alarms, etc.
last option is going to be to open up some memory and delete some of that 32GB of data you are storing.

Is jailbreaking the only way to disable low battery notifications?

this is so annoying and i dont care about this feature, i know i should plug my phone in but i dont like having to sit next to an outlet to let my phone charge while i play street fighter 4, and turning off notifications doenst stop this low battery notification from showing up, does apple really want me to jailbreak my iphone or what lol?

Jailbreaking also increased the likelihood that you'll never be able to update or restore your iPhone again. Search "error 1015" in this forum - there are more and more who are SOL. If you're looking forward to iOS 5, you may never get it.
Don't believe the hackers who tell you jb is "perfectly safe" and all you have to do is restore to get rid of it. They tell you this just before making you accept an "as is" user agreement, holding them harmless for any damages.

IPad gets lower rate than iPhone

Looking at my Airport Extreme, I see that my iPad is connected with a wireless rate of 39Mbps. My iPhone is getting 54Mbps. They are both about 6 feet away from the AE. How can this be?

Your iPhone is connecting using 802.11g while the iPad uses 802.11n. For some reason it gets limited to 39mbps. If you set up your Airport Extreme to only allow G, the iPad will get 54 too. And in my case be more stable as well.

Disabling Low Rates on a WLC

Similar Messages

Maybe you are looking for