Disappointed by Twist S230u display touch did not work

I bought new Lenovo twist s230u from ANTOnline.com on 10th Jun and received it on 15th Jun same day I have identified its touch screen not working reported back to ANTOnline and then suggested to contact Lenovo thinkpad support so i did initially they suggested to refresh and reload OS but that did not workand finally I had to send the laptop to Lenovo service center, now Lenovo took 2 weeks to repair buggi laptop screen and mother board as laptop screen was coming from china so i received back laptop with list of five component they have change and also a paper saying quality and functional testing pass well as soon as I started laptop touch screen started working but it took me 10 mins to figure out that laptop is not functioning properly as screen rotation button was not fitted propely so screen was not rotating and it was getting stuck, lower volumn button was not fitted properly so it was always on mute and I could not increase the volumn and third defect and best is now touch pad stoped working so I callled Lenovo thinkpad service again and sent laptop back to them again now its been two weeks more and laptop is still with them and support notes shows that they have changes few more parts in that laptop
I feel like lenovo dont have any quality in their products its been more than months I bought it and i am still not able to use it infact it is not with me I feel like I m fooled by ANTOnline and Lenovo both as I feel like i bought refurbished than new as it has so many issues. How long will i be sending laptop to Lenovo service i bought new to use not to repair untill it is in warrenty I am not even aware where should i put the complaint about it..

three finger tap three times
or
three finger tap and slide

Similar Messages

How can I connect my MBA 11" 2012 to my Imac 21.5" mid 2010 as a display unit. Connected using a mini display port cable and this did not work. Any guidance welcome. Thanks. John

I bought a belkin mini display unit cable( new) and connected the thunderbolt port in the MBA ( 11" , mid 2012) to the Imac mini display unit port using this cable. Pressed the CMD & F2 keys on the Imac keyboard as required but this did not work. Should I try with another cable ? Should i try with a thunderbolt cable ( recommended by appple support ) -- but they too were not sure about this. Is the Mid 2010 21.5" Imac not able to function as an display unit? Any guidance would help and will be much appreciated.

Welcome to Apple Support Communities
Only the 27-inch iMac and Mid 2011 and newer iMacs can be used as an external screen, so you can't use your Mac as an external screen. See > http://support.apple.com/kb/PH11302
You can still use your iMac as an external display, using an application like ScreenRecycler

When i go in my settings on my ipod touch 3gen it says no wi-fi as in i cant connect to any wi-fi at all i tried to restore but did not work HELP PLEASE

when i go in my settings on my ipod touch 3gen it says no wi-fi as in i cant connect to any wi-fi at all i tried to restore but did not work HELP PLEASE

See:
iOS: Wi-Fi or Bluetooth settings grayed out or dim
If not successful, an appointment at the Genius Bar of an Apple store is usually in order.
Apple Retail Store - Genius Bar

I am having trouble looking at video podcasts on my ipod touch. they are all greyed out. I have tried removing them and resyncing. this did not work. any ides?

I am having trouble looking at video podcasts on my ipod touch. they are all greyed out. I have tried removing them and resyncing. this did not work. any ideas?

Try:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Unsync all media and resync
- Reset all settings
Go to Settings > General > Reset and tap Reset All Settings.
All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.

My ipod touch thinks headsets are plugged in as indicated when pressing volume control. We did a reset but that did not work. What is next?

My ipod touch thinks headsets are plugged in as indicated when pressing volume control. We did a reset but that did not work. What is next?

- Try cleaning out/blowing out the headphone jack. Try inserting/removing the plug a dozen times or so. There is a little switch in the headphone jack that disconnects the speaker when the headphone jack is inserted.
Try the following to rule out a software problem
- Reset the iOS device. Nothing will be lost
Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Reset all settings
Go to Settings > General > Reset and tap Reset All Settings.
All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
- Restore from backup
- Restore to factory settings/new iOS device.
- Make an appointment at the Genius Bar of an Apple store. Seems you have a bad headphone jack.
Apple Retail Store - Genius Bar
If not under warranty Apple will exchange your iPod for a refurbished one for this price. They do not fix yours.
Apple - iPod Repair price
A third-party place like the following will replace the jack for less. Google for more.
iPhone Repair, Service & Parts: iPod Touch, iPad, MacBook Pro Screens
Replace the jack yourself
iPod Touch Repair – iFixit

Downloaded ios6 to my ipod touch and lost all color when i select an artist or song how can i get to be blue again tried resetting did not work any help would be apprciated?

just downloaded ios6 on my ipod touch and lost all color when I select an artist or song how can I get it to be blue again tried resetting did not work any help offered would be liked

You need to restore.
Everything should be on your computer, so you can just sync it back.
iPod touch User Guide (For iOS 4.3 Software)

Why apple password did not work with my Ipod Touch

why my apple password did not work with my Ipod Touch?

Just where are you entering it?
What happens when you try?

My mac book pro 17 inch , 2008 year , display went dark, and the steps in "everthing Mac" book did not work, any ideas?

my mac book pro 17 inch , 2008 year , display went dark after rebooting from origianl disc, and the steps in "everthing Mac" book did not work, any ideas?

The router might be bad or incompatible, but let's be optimistic.
On System Preferences, go to Network/Advanced/PPP. Only two items should be checked: Connect Automatically When Needed and Disconnect when switching user accounts. Uncheck everything else. Now, click Okay on the end of the page. The next time you're online, you shouldn't be disconnected.
If you still get disconnected like before, we might be dealing with a router issue - which can get rather complicated.

HT1212 My ipod touch (iOS 6) got locked & I tried backing it up on itunes and it did not work. Please help!!!

My laptop broke & now I have to use a different computer to try and reset it.

Without knowing exactly"why it did not work (error message?) all I can suggest:
Place the iOS device in Recovery Mode and then connect to your computer and restore via iTunes. The iPod will be erased.
iOS: Wrong passcode results in red disabled screen
If recovery mode does not work try DFU mode.
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
For how to restore:
iTunes: Restoring iOS software
To restore from backup see:
iOS: How to back up
If you restore from iCloud backup the apps will be automatically downloaded. If you restore from iTunes backup the apps and music have to be in the iTunes library since synced media like apps and music are not included in the backup of the iOS device that iTunes makes.
You can redownload iTunes purchases by:
Downloading past purchases from the App Store, iBookstore, and iTunes Store

My iPhone got wet.. The phone is working except the home button but Siri is working.. I had also added the assistant touch but in that also the button did not work.. So what should I do???

My iPhone got wet.. The phone is working except the home button but Siri is working.. I had also added the assistant touch but in that also the button did not work.. So what should I do???

The phone is damaged. Take it in to an Apple Store or authorized service provider. More than likely you will have to pay for an out of warranty replacement.

Recently purchased iPod Touch did not come with current firmware

I have just received my 32GB iPod touch from china but it did not come with the 3.0 update.
Why do I have to pay for an update that was released over a month before I bought the iPod from Apple?
Also, iTunes will not stop bothering me about updating to 3.0. Every time I open iTunes, a popup dialog come up asking me if I want to update the iPod Touch to 3.0.
I would love to update but I refuse to pay for an update that's over a month old.

Well, 3.0 really isn't an update as much as it is a new accessory for your Touch. It may seem like it should be an update, but it introduces many new features. If all it did was fix some errors it would be an update, but this is an entirely new release, hence the $10 charge. Trust me, you're not alone in expecting a new Touch to come with 3.0, but the reality is that this is how Apple's done this in the past (when 2.0 came out, the 1st generation Touches did not come with it -- only the 2nd generation ones did). iPhone users get 3.0 for free, but in reality that is a perk that Apple gives them for paying a monthly access fee. My guess is that 3.x won't come with a brand new Touch until the next generation is introduced.
As far as the incessant "do you wanna buy 3.0" message, that may eventually go away if you decline it enough times.

I have a 4th gen iPod touch that won't power up! I tried all the traditional stuff. I want to know how to tell if the battery is good. itunes see's the ipod in recovery mode. Tried dfu mode and did not work. Any ideas?

I have a 4th gen iPod touch that won't power up! I tried all the traditional stuff. I want to know how to tell if the battery is good. itunes see's the ipod in recovery mode. Tried dfu mode and did not work. Any ideas? I can hear the PC beep when plugging it in! I suspect a bad battery and trying to charge it ina wall charger made it hot!

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order. The appointment is free.
Apple Retail Store - Genius Bar

Ipod touch did not prompt to enter apple id password when installing an application.

I tried to do a restore and tried using creating another apple id. But still the ipod touch did not prompt me to enter apple id password and immediately proceed to install the application. How to solve this? Please help .....

Hi,
Yes. I tried to install another application within 10-15mins. Thanks for enlightening me as I'm new to Apply products. Feeling kind of silly that I did not really read up the user guide. Thanks for your advise.

The thunderbolt firmware 1.2 update keeps reappearing. I have a MacBook Pro and 2011 Thunderbolt display. Did not discionnect when upgrading to Yosemite (only read the instructions later). Thanks.

Hi There,
I have a MacBook Pro (late 2011) and a Thundertbolt Display. I have recently upgraded to Yosemite. Since then Thunderbolt Firmware update 1.2 keeps reappearing and I cannot complete the update (with and without display connected etc.). Any advice? Thanks.

Hello HTG65,
If the Thunderbolt Firmware Update 1.2: Keeps reappearing try reinstalling it following the steps in this article.
Thunderbolt Firmware Update 1.2: Keeps reappearing and Thunderbolt ports and Target Display Mode may not work - Apple Support
To resolve this issue:
Shutdown your computer.
Disconnect all Thunderbolt devices.
Wait 10 seconds.
If you are using a Mac mini with a Thunderbolt display, reconnect the Thunderbolt display directly to your computer via the Thunderbolt port. Do not connect other Thunderbolt devices at this time.
Restart your computer.
If the Thunderbolt Firmware Update 1.2 is offered, download and install it and restart your computer when asked. If the Thunderbolt Update is not offered, the update has installed correctly.
Reconnect all Thunderbolt devices.
Take care,
Nubz

Quick launch buttons and touch functions not working post win7 upgrade

I have several problems that I think are related.
1) When I rotate the screen and then bring it close (as in flat) to the keyboard, the screen goes blank. There is no key combination I can find that restores the screen. Putting it back in notebook orientation doesn't do anything either. Only thing to do is a hard reboot.
2) the quick launch buttons on the screen edge are not functioning as follows:
a) the hp mediasmart button (the one with the wave) doesn't work
b) the screen rotation button produces the same problem as 1) above
c) the third button which looks like either gears or a sun (I don't know what it should do) brings up the windows mobility center, where I have found problem number:
3) On tablet PC settings, the display tab, there is one display: 1. mobile PC display
on the same tab, there is a setup button. The next screen says:
pen input
touch input
Regardless which one I select, on the following screen (where it says Press this screen with ....) when I press with either my finger or the pen, nothing happens. Which seems like either:
it thinks another screen is active or
the touch components are completely non functional.
4) Not surprising, the touch functions are completely non-functional
I have installed all of the drivers for this TX2-1025dx for Win7(64bit) per the HP support/drivers page.
Not all of them resulted in a clean install.
Here are other drivers that I had problems with (meaning that I got an error message, it failed, it had to be done more than once, something else broke, etc.)
AMD AHCI - started catalyst installer then failed
Authentic fingerprint driver - "dpinst64 not marked for installation"
Ntrig Duosense - had to do this one multiple times to get the fingerprint reader to work
HP Mediasmart MVP - hung in CMD
I have checked that all of the startup services are actually enabled in msconfig including quick launch buttons, hpwuschd, and media smart. Nothing is disabled in services.
I have reinstalled the quick launch buttons driver for this product from December 2009. (There is an earlier version from November.)
I installed the bios upgrade (before win7, actually) it is currently F.25
I have also eliminated EMF possibilities.
I have searched the forums, and while I have found some interesting clues, I don't see anything like this - at least with a solution.
Any assistance would be greatly appreciated as this thing is quite useless to me as it currently functions. It is not a tablet anymore.
TIA

[knock knock] Helloooooo??!!??
Installed 6.50.9.1, which is in between the last two quick launch button (QLB) drivers (that did not work). Also fixed the lightscribe and mediasmart DVD installs. Same problems, no touch or pen, and a new bug I discovered with qlb
First, if you search for tablet in the start menu, there is a selection to set the tablet buttons to perform certain tasks. When you run that, it says that teblet buttons are not installed on this pc. Doesn't matter if QLB is installed or not - same error. Hmmmmm. Check with your pc manufacturer..... I think I am doing that. I am starting to feel like I am working for HP.
Next finding: Using mobility center, I found that if you orient the screen to landscape for the slate config, and then rotate the screen, it does not go blank. However, if you rotate the screen back to notebook, it goes blank. And of course it keeps that upsidedown config when you reboot, too. So, the way to recover from that (because you really need a keyboard if you don't have a working pen and touch takes 30 sec to respond) is to keep trying to get touch to orient the screen back to landscape for notebook. Then rotate the screen to landscape for notebook. And uninstall the QLB driver that doesn't work and reboot. But after that, touch and pen did not function.
Since touch and pen had previously been restored when I uninstalled QLB, I reinstalled MVP and smartmenu coz they were the actions that I took the last time before touch and pen returned. Didn't work this time, tho.
I decided to do a system restore back at the point that I had used HP Advisor, since that was the last time I made note that pen and touch were working. Restore failed because a sfi.dat file was not found (and search didn't find it anywhere either). I tried 5 different restore points, before and after that one, and they all failed. But the first time around, I had touch on the logon screen, just not after windows started. The next time, I had touch but not pen. The next time, I had touch and pen, but only for a period of time (I think HP Advisor may have been the intervening event) before they stopped working.
Oh, and HP advisor does not appear to be actually installing the things on the action list. That could be an issue with Comodo, but it really looks more like an issue with that "mother may I" message from Windows asking for permission to run the program. Often as not, windows reports that the program is not responding. Closing the program with that dialog box actually gives it the kick in the knickers it needs to complete.
A not so great workaround is to use the mobility center to orient the screen when you want to put the thing in slate mode. You can pin it to the task bar (with a little fiddling). Touch is extremely slow to respond in slate mode. For example, it took about 3 minutes to get the screen oriented back around to notebook config, which is 4 "clicks" if things are working right. Pen works sort of OK (although I haven't tried any writing) . Gestures for scrolling do not work.
I am done with the troubleshooting until someone comes up with other targeted ideas.I have been keeping detailed chrono notes.
Again, I hope the information here leads to a solution. This unit is not a functional tablet and I don't want to stay with Vista, neither should I have to since this is supposed to be compatible.

Disappointed by Twist S230u display touch did not work

Similar Messages

Maybe you are looking for