Discussion Jabber on Notebooks and Cisco 2901 gateway

At work we now have Cisco Jabber clients on notebooks. Internal connections are now possible, allthought with great latency because the central "master" resides a thousand kilometers thru europe away behind a VPN-connection. As a country subsidiary a local cisco 2901 should connect to the telephony as a gateway...
- How is the general architecture of cisco collaboration?
- Is it correct to look at our cisco 2901 like a local domain-controller in windows-network?

Hi
Thx for the answer. To figure it out more clear on a top-level:
We are sitting in the south of europe and our master resides up in North. Using Jabber clients on notebooks a telephony-call to customers in our country will go throught vpn-tunnel up north to u-turn and come down to our cisco2901 which is connected to legacy telephony-(ISDN-)wires and finally to customers...
Is this a recommended architecture?

Similar Messages

Cisco Call Manager 5.1 and Cisco VoIP Gateways

Hi,
I have Cisco Call Manager 5.1 with Cisco 2800 series routers as a ISDN gateways and Cisco VG224/ATA 186 as POTS gateways. While Cisco Call Manager collects call statistics from 7900 series SCCP handsets managed by the Call Manager (number of VoIP packets, dropped frames etc.), it shows only one side of the call as it does not collect statistics from the Cisco routers (configured as H.323 gateways), the Cisco VG224 (with ports configured as H.323 gateways and as a SCCP devices) and Cisco ATA 186 (configured for SCCP).
Is the collection of these statistics possible? What needs to be done?
Thanks,
Paul

Update: Logging of QoS/Call Management Records (CMR) to Call Manager CDR database is not possible with H.323 gateways; only MGCP gateways:
http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_qanda_item09186a008020650a.shtml#qa4
Anyone know how to get the Cisco router gateway to log these statistics anyway using standard router logging mechanisms (e.g. syslog)?
Anyone know about calls to SCCP ports on Cisco VG224 or ATA 186?
Thanks,
Paul

Cisco Presence/Jabber both internally and externally

We have installed the Cisco Presence server and intergrated it with our Microsoft Exchnage for ldap, Cisco Unified Communications Manager, and Cisco Unity Connection for phone and voicemail support. It is all installed inside our corporate network and with my testing, I have found it to be available outside our Corporate network as long as I have a VPN configured and active from outside.
However, management wants the enitre thing accessible from both within and from the outside without having to have a VPN connection. Does anyone know of a method for doing this or could point me to some good documentation as to what would be required?
Thanks in advance.
Gene

If you are using Jabber onPrem with CUPS, the only way this will work (for now) is using VPN. This will give the external using IM/Presence/CUCM. You cant really open CUCM or CUPS via 5060 Ports and expect it to work. The problem is the internal/external IPs are not proxied correctly and presence will not work.
If your management really wants to have this seamless inside and out, the best solution right now is to use Jabber Cloud and use VPN back for CUCM call control on the client. (mobile or PC/Mac).
Hopefully sooner than later we will see a "Presence gateway" that will sit in the DMZ and connect external IM clients to the internal CUPS server,

Call/video not working between Cisco jabber for Windows and VCS control C40s

Hello,
I've been struggling with no luck how to make a call using Cisco Jabber for Windows 9.6.0 registered to CM 8.6.2 with intercluster ICT to another CM 8.6.2 where we have a VCS Control 7.0.2 via GK H225, and all C40s are registered as H.323.
The VCS has interworking between H323 and SIP, however not sure if there is any problem with that. Assuming it is ok, not sure either if I'm facing any interoperability issue because in my remote site I have C40 (H323 registered at VCS and SIP listening mode) and cisco jabber for windows which is SIP based.
If is not possible, would I be able to change my C40 from H323 to SIP at VCS, or have both H323/SIP registered at VCS? If so, will I need to change as well instead of GK I'll have to establish a SIP Trunk between the CM and VCS?
Another thing I do not believe either I would be able to have one VCS connected with two clusters, right?
I'm just trying to find a solution in case my current topology is not compatible, but feel free if you have any better idea to make it work.
Anyway here is what is happening:
When I make a call from my cisco jabber windows to C40 using alias number. The call is being redirected just fine to the C40 and it rings, however when someoene or the auto answer picks it up, the call dropped right away.
However, if I enabled the MTP in my CSF device, the call gets longer before dropping. I was even able to see my jabber " start video" turns green, before was grayed out all the time and the call dropped faster. I hear a fast busy tone.
I'm able to provide SDI traces, logs, diagnostic sip/h323 calls from VCS in order to know for sure if this is an incompatible issue or something I can workaround.
Let me know if someone of you are interested in read these logs or could point me on the right direction.
Thanks!

Ok,
I have looked at both logs. I have to mentinon though that you didnt
provide the log that shows the h323 setup between cucm and the VCS. This
is most likely because the call originated from a different cucm than
the ones you provided the logs from.
The call would have orginated from the first cucm in the cucm group of
this trunk: Name=RL_TRUNK_VIDEO
The cucm ip will be : 10.252.53.10.
This is the VCS log that confirms where the h323 request originated
from:
pr 10 22:50:29 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:29,187"
Module="network.h323" Level="DEBUG": Src-ip="10.252.53.10" Src-
port="54000"
Received RAS PDU:
Having said that here is my analysis of the logs that you sent..
Jabber sent an INVITE to CUCM and advertised all the codecs (audio and
video it can support)..
Observer that Jabber says it doesnt support G729 anexB
21:55:16.576 |//SIP/SIPTcp/wait_SdlReadRsp: Incoming SIP TCP message
from 10.223.20.73 on port 54677 index 90661 with 2220 bytes:
[862370,NET]
INVITE sip:[email protected];user=phone SIP/2.0
Via: SIP/2.0/TCP 10.223.20.73:54677;branch=z9hG4bK000029d3
From: "4122107" <sip:[email protected]>;tag=00059a3c78000011000070b0
-00000e65
To: <sip:[email protected]>
Call-ID: [email protected]
Max-Forwards: 70
Date: Fri, 11 Apr 2014 01:55:16 GMT
CSeq: 101 INVITE
User-Agent: Cisco-CSF/9.4.1
m=audio 19252 RTP/AVP 0 8 18 105 104 101
c=IN IP4 10.223.20.73
a=rtpmap:0 PCMU/8000
a=rtpmap:8 PCMA/8000
a=rtpmap:18 G729/8000
a=fmtp:18 annexb=no
a=rtpmap:105 G7221/16000
a=fmtp:105 bitrate=24000
a=rtpmap:104 G7221/16000
a=fmtp:104 bitrate=32000
a=rtpmap:101 telephone-event/8000
a=fmtp:101 0-15
a=sendrecv
m=video 28878 RTP/AVP 97
c=IN IP4 10.223.20.73
++++Now lets observer the capabilites exchange during h245 negotiation
between cucm and VCS++++
Here CUCM advertises its caps to VCS (afterreceiving caps from VCS)
Note that G729A, G729AB, G729 is all advertised..
Apr 10 22:50:31 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:31,017"
Module="network.h323" Level="DEBUG": Src-ip="10.252.53.10" Src-
port="45660"
Received H.245 PDU:
value MultimediaSystemControlMessage
::= request : terminalCapabilitySet
capabilityTableEntryNumber 2,
       capability receiveAudioCapability :
g729wAnnexB : 6
       capabilityTableEntryNumber 3,
   capability receiveAudioCapability : g729AnnexAwAnnexB : 6
       capabilityTableEntryNumber 4,
       capability
receiveAudioCapability : g729 : 6
capabilityTableEntryNumber 5,
       capability receiveAudioCapability :
g729AnnexA : 6
++++++
After doing MSD (master slave determination, we move to the OLC phas e..
Here we see that the far end..c40 wants to use G729AB for media++++
Apr 10 22:50:31 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:31,783"
Module="network.h323" Level="DEBUG": Src-ip="10.224.114.11" Src-
port="11163"
Received H.245 PDU:
value MultimediaSystemControlMessage
::= request : openLogicalChannel :
   forwardLogicalChannelNumber 1,
forwardLogicalChannelParameters
     dataType audioData :
g729AnnexAwAnnexB : 20,
     multiplexParameters
h2250LogicalChannelParameters :
+++Next VCS sends G729AB as the codec to use to CUCM+++
Apr 10 22:50:31 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:31,784"
Module="network.h323" Level="DEBUG": Dst-ip="10.252.53.10" Dst-
port="45660"
Sending H.245 PDU:
value MultimediaSystemControlMessage
::= request : openLogicalChannel :
   forwardLogicalChannelNumber 1,
forwardLogicalChannelParameters
     dataType audioData :
g729AnnexAwAnnexB : 20,
     multiplexParameters
h2250LogicalChannelParameters :
++++The next thing we get is an OLC reject from CUCM and this is where
th call drops++
Apr 10 22:50:31 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:31,790"
Module="network.h323" Level="DEBUG": Src-ip="10.252.53.10" Src-
port="45660"
Received H.245 PDU:
value MultimediaSystemControlMessage
::= response : openLogicalChannelReject :
forwardLogicalChannelNumber 1,
   cause dataTypeNotSupported : NULL
Apr 10 22:50:31 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:31,790"
Module="network.h323" Level="INFO": Dst-ip="10.224.114.11" Dst-
port="11163"
Detail="Sending H.245 OpenLogicalChannelRejResponse
+++We then receive a call release from cucm with cause code of 47:
resource unavailable++++
Apr 10 22:50:32 TWELDVCS01 tvcs: UTCTime="2014-04-11 01:50:32,365"
Module="network.h323" Level="DEBUG": Src-ip="10.252.53.10" Src-
port="50913"
Received H.225 PDU:
Q931
   Message Type: Release
Complete
   Call reference flag: Message sent from originating side
Call reference value: 0x7b
   Info Element : Cause
     Location: Usr
   Cause Value: Resource unavailable
   Info Element : User User
   Length = 22
Suggestions:
Change the region setting between the ICT trunk to VCS and Jabber to use
G711 and test again.

Transfer VOIP Calls Between Cisco Desk Phone and Cisco Jabber For IPhone 9.5

Does anyone know how to transfer an active voip call from a Cisco IP Desk Phone to Cisco Jabber for IPhone? I can transfer a call from Cisco Jabber for IPhone to my Cisco IP Desk Phone no problem. I put the call on hold and then click "Resume" on my Cisco IP Desk Phone. However I cannot do the same but the other way around. If I put the call on hold on my Cisco IP Desk Phone, I see "no active call" on my Jabber client. The only information I could find slighlty relevant was using the Mobility Key/Remote Destination Profile feature however this defeats the object as this will forward to an external number, e.g. mobile and I just want to transfer the call within the VOIP environment between the two devices that are using the same directory number.
I am using Cisco Call Manager 9.1(2), Cisco Presence 9.1 and Cisco Jabber for IPhone 9.5.
Any help would be greatly appreciated.
Kind Regards,
Paul Parker.

Did you ever find an answer to this ?
I am seeing the same behavior and trying so see if I can put calls on hold and pick them up both ways also.
The only answer I seem to have found is to use park instead
That would/should work but I would just prefer to hold/unhold
Just not sure why we would not be able to hold/unhold on what is essentially a "shared" line
Does anyone have this working for them ?

What's wrong? Verify and compare Cisco 2901 config after loading old config from Cisco 2801

Hi Cisco Community / Friends,
I am new to this site though I have cisco account for many years. I am a CCNA ,I passed my certification on January 2013 I seldom use and utilized my skills on networking becuase of my type of work. I am Project Eng'r working in a System integrator company . Anyway, I would like to ask assistance on the configurations of my Cisco router for this gov't projects.. Here's the situation.
We have a new project for the VSAT Comm'n of Coast Watch Station , The VSAT was installed 7 years ago. The VSAT was only used for a year by this Gov't agency because of subscription issue. Now, they wants to revive and use their VSAT facilities for the Coast watch monitoring. Now, some of this routers are working up to now and for some site are already defective so I need to replace the old 2801 router with a new equivalent model which is Cisco 2901. My plan was just to load the old config into the new Cisco 2901 router. However, after loading it to the new router, I am a little worried because I've got some errors received. I load the old config by copying the old files, edit it in notepad, and load the config using Secure CRT (terminal emulator). When I copy the old config of cisco 2801 to new router cisco 2901 , below are the command not recognized on Cisco 2901. What's wrong ? What are these commands for?
Appreciate your comments and help on this matter.. Thank You very much
Note: I Attached the original config from Cisco 2801 and the other file is the config after I load the config file to Cisco 2901.
(Errors see below)
CWS_4_Pandami(config-erm)#mmi polling-interval 60
                         ^
% Invalid input detected at '^' marker.
CWS_4_Pandami(config-erm)#no mmi auto-configure
                               ^
% Invalid input detected at '^' marker.
CWS_4_Pandami(config-erm)#no mmi pvc
                               ^
% Invalid input detected at '^' marker.
CWS_4_Pandami(config-erm)#mmi snmp-timeout 180
                                                        ^
% Invalid input detected at '^' marker.
CWS_4_Pandami(config-if)#interface GigabitEthernet0/1
CWS_4_Pandami(config-if)# description ===CWS4 SAT Modem===
CWS_4_Pandami(config-if)# bandwidth 256
CWS_4_Pandami(config-if)# ip address 192.168.42.1 255.255.255.0
CWS_4_Pandami(config-if)# duplex auto
CWS_4_Pandami(config-if)# speed auto
CWS_4_Pandami(config-if)# priority-group 1
                                                    ^
% Invalid input detected at '^' marker.
CWS_4_Pandami(config)#access-list 100 permit ip any any dscp cs5
CWS_4_Pandami(config)#priority-list 1 protocol ip high list 100
                          ^
% Invalid input detected at '^' marker.

Hi
From Cisco's website:
The Modem Management Interface (MMI) is software that enables auto-provisioning for the Cisco 827 routers. The MMI uses a fixed PVC to communicate with the Proxy Element (PE) residing on the digital subscriber line access multiplexer (DSLAM). Using MMI, the Cisco 827 router updates the running image and downloads the prescribed configuration using a configuration file or configuration values in a provisioning information database.
The customer premise equipment (CPE) can be automatically configured using the Cisco DSL CPE download, but it can be configured only with the image provisioning feature.
So because this is your device, you don't want to use MMI anyways.
And "priority-list" is QoS. Probably that QoS-command is old and removed, because now QoS is configured using class-maps and policy-maps.

Connectivity issues between Cisco 2901 and Cisco SG300-52

Hello,
I am having some serious connectivity issues between the hosts in my LAN.
My LAN is based on a Cisco 2901 router and a Cisco SG300-52 port switch.
The issue that has been happening is that connections between hosts on the LAN (remote desktop, extended ping, etc) is very unstable, at some point I can see a 35% lost packets on an extended ping. This happens at any time of the day and from any host.
All hosts are on the same Vlan(default Vlan) and on the same subnet. Some hosts have fixed IP addresses (servers and network equipment) and others obtain their IP address trough a DHCP reservation established on the router (reserved with the MAC address of every host).
I can provide further details if needed, because this issue is very serious and I would really appreciate any insight or support.
Many thanks in advanced.
Sair Amer
EDIT: After doing every test we could think of, we finally found the reason behind this problem.
It turns out that the switch has problems handling communications between clients at different speeds, because most of the hosts connected were working at 100 Mbps but the servers were working at 1000 Mbps (and the communication between host and servers wasn't stable).
After manually setting the speed on all ports to 100 Mbps the problems have stopped.
Many thanks for you help on this issue.

Building configuration...
Current configuration : 4123 bytes
! Last configuration change at 12:06:16 PCTime Sat Jul 19 2014 by ccp
version 15.2
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Foninsa
boot-start-marker
boot-end-marker
no logging buffered
enable secret 5 $1$BDbJ$HN3VP8nmywrGB55RCxPd30
aaa new-model
aaa authentication login default local
aaa authorization exec default local
aaa session-id common
clock timezone PCTime -4 0
clock summer-time PCTime date Apr 6 2003 2:00 Oct 12 2003 12:00
no ip cef
ip dhcp excluded-address 192.168.1.1 192.168.1.10
ip dhcp excluded-address 192.168.1.151 192.168.1.255
ip dhcp pool FONINSA
network 192.168.1.0 255.255.255.0
default-router 192.168.1.1
dns-server 8.8.8.8 8.8.4.4
ip dhcp pool Laptop-Sporta-Wifi
host 192.168.1.10 255.255.255.0
ip name-server 8.8.8.8
ip name-server 8.8.4.4
no ipv6 cef
multilink bundle-name authenticated
crypto pki trustpoint TP-self-signed-213585710
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-213585710
revocation-check none
rsakeypair TP-self-signed-213585710
crypto pki certificate chain TP-self-signed-213585710
certificate self-signed 01
30820229 30820192
quit
license udi pid CISCO2901/K9 sn
license boot module c2900 technology-package securityk9
username ccp privilege 15 password
redundancy
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
ip address 190.196.21.98 255.255.255.248
ip nat outside
ip virtual-reassembly in
duplex auto
speed auto
interface GigabitEthernet0/1
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
no ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
ip nat inside source list 1 interface GigabitEthernet0/0 overload
ip nat inside source static tcp 192.168.1.3 21 190.196.21.98 21 extendable
ip nat inside source static tcp 192.168.1.3 80 190.196.21.98 80 extendable
ip nat inside source static udp 192.168.1.8 1194 190.196.21.98 1194 extendable
ip nat inside source static tcp 192.168.1.4 3389 190.196.21.98 3389 extendable
ip nat inside source static tcp 192.168.1.9 3389 190.196.21.98 10000 extendable
ip nat inside source static tcp 192.168.1.3 3389 190.196.21.98 20000 extendable
ip route 0.0.0.0 0.0.0.0 190.196.21.97
access-list 1 permit 192.168.1.0 0.0.0.255
control-plane
line con 0
password $
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 5
access-class 23 in
privilege level 15
password #
transport input telnet ssh
no scheduler allocate
end

Document on Cisco 3845 gateway with both Voice and VXML role

Dear all,
we are using single cisco 3845 gateway as Ingress as well as vxml gateway . Can you provide any documentation regarding the call volume capacity this gateway can handle. We have deployed this gateway in a UCCE parent- child model.

Anoop,
It can be found in Table 7-2 on page 148 of CVP SRND Guide
HTH
GP.
Pls rate helpful posts by clicking on the stars under the post !!

Setup of 2 B-channel transfer (TBCT) on Cisco Voice Gateway

Hi all,
In my scenario, I have several remote locations, each with their own T1-PRI connection to the PSTN via Cisco voice gateways.
The call flow has the caller calling a PSTN number at the remote location. This call hits a CUCM translation pattern and is immediately hairpinned/tromboned out to a PSTN number located at the UCCE central location.
The customer would like to perform a 2 b-channel transfer back up to the CO switch, to free up B-channels to the remote location.
My question is this: Assuming my switch type is supported and the PSTN provider supports 2 b-channel transfers, do I simply need to add "isdn supp-service tbct" to my serial interface configuration?
I have seen discussions that it is as simple as this, to needing some tcl/xml code, to also requiring aaa to be setup.
As there are over 100 locations being considered for this enhancement, the customer would like to know if it is 15 minutes or 2 hours per location to implement.
Thanks,
Joe

Thanks Paolo,
That was my expectation.
They have this going on the VG's utilized by CVP, so I will ask them to review the XML in use there for tweaking for the remote locations.
Thanks again!
Joe

Uc500 and cyberdata paging gateway

I am setting up a Cyberdata sip endpoint for paging. I have successfully installed the cyberdata sip intercom on other systems (uc540) and they work well. I am not having much success with the amp. I have tried many configurations in both the uc540 cli and the cyberdata sip paging gateway.. I am including the latest config and the latest debugs.
Cyberdata was a help in the beginning but they are lost as well. When I dial the extension I get a fast busy. No matter how I configure it I get a fast busy when I dial the extension. The unit does show that it is registered with the sip server. It could be an acl issue, but I don’t want to change the acl’s until I know for sure.

this is a paging gateway for loudspeakers. The intercoms that I have configured are working fine. if you like to see the settings I used let me know. When someone presses the call button I have it ringing to a call blast group, when they answer they get a two way conversation and the when they press a button (5) the door opens. I used a vlan1 address on the intercom, but in the settings I used in cli I used the vlan100 address of the sip server.It does show "registered with sip server" thanks
Barry Hunsinger
SBI, LLC
Small Business Integration, LLC
908-265-2006 cell
908-753-0420 fax
[email protected]
[email protected]
Cisco Select Certified
Cisco Small Business Communication Specialist
www.sbi-nj.com
>>> pennautomotive <[email protected]> 5/25/2012 12:42 PM >>>
Home ( https://supportforums.cisco.com/index.jspa )
Re: uc500 and cyberdata paging gateway created by pennautomotive ( https://supportforums.cisco.com/people/pennautomotive ) in SBCS - UC500 - View the full discussion ( https://supportforums.cisco.com/message/3644878#3644878 )
Also is worth mentioning that for me the intercom itself would not show up as registered through its web interface.
Reply to this message by going to Home ( https://supportforums.cisco.com/message/3644878#3644878 )
Start a new discussion in SBCS - UC500 at Home ( https://supportforums.cisco.com/choose-container!input.jspa?contentType=1&containerType=14&container=2195 )
Message was edited by: Barry Hunsinger
The calls to the cyberdata amp are trying to go out to our sip provider, and of course the call fails with a fast busy. how do I keep the call inside and get it to the amp.Is it a dial peer issue ?

I can not share file from Jabber for Iphone and Android

Hi guys.
I have:
CUCM9.1/Publisher y Subscriber
System version: 9.1.1.41900-1
Presence/Publisher
System version: 9.1.1.41900-1
Expressway x8.1.1
Cisco Cisco Expressway-E
Expressway x8.1.1
Cisco Expressway-C
Jabber for Android and Iphone 10.6
I do not have "file transfer" and my Iphone an Android.
I don not have "share desktop" from internet on my windows jabber.
The calls and chat is working fine, but when I wante send a file, the option on my iphone is disable.
Why?

Hi dennisalpizar07,
check this:
Jabber for Android officially supports receive BFCP video sharing on TAB devices (normally used for Android Tablets without native calling capability).
The Jabber for Android 10.6 release enters a beta trial on receiving BFCP video sharing on BOT devices (normally used for Android smartphones and phablets)
page 2 of the Cisco Jabber for Android 10.6.x Release Notes.
Hope this helps.

Where is the documentation for Jabber for iPhone and iPad 9.6.1 ???

Jabber for iPhone and iPad 9.6.1 was released on Tuesday Jan 14th 2014.
I see the 4 .cop files on cisco.com in a zip file copfiles_iOS96.zip. What is the difference between the 4 files? Application in the AppStore on my iPad, but there are no release notes, or documentation on cisco.com. All I can assume is that these .sgn files need to go on my Publisher/TFTP server?
Nothing here about a 9.6.1
http://www.cisco.com/en/US/products/ps11596/prod_release_notes_list.html
iTunes
https://itunes.apple.com/us/app/cisco-jabber/id467192391?mt=8
cop sgn files
http://software.cisco.com/download/release.html?mdfid=284288351&flowid=45930&softwareid=284006014&release=9.6%281%29&relind=AVAILABLE&rellifecycle=&reltype=latest

I only see two COP files, one for iPhone (TCT) and one for iPad (TAB). These are required on older (can't believe I'm calling 8.6 older already!) builds of CUCM.
Which other files do you see?
Please remember to rate helpful responses and identify helpful or correct answers.

Problem: IPv6 w/ PPPoE on Cisco 2901

Folks: I have this Cisco 2901 configured with PPPoE and IPv6 and connect it through a CO (DSLAM) to an Actiontec xDSL router. PPPoE connections are on FE0/0/0, through virtual template.
The Actiontec router gets NA and PD addresses succesfully and LAN PC connected to Actiontec router can surf the IPv6 Internet w/ no problem. However, Cisco 2901 can't reach the Actiontec router by its NA or TA public IPv6 address. A 'stupid' workaround is to manually add a route w/ the virtual access. It is stupid cuz each new connection will bring up a different virtual acess.
I guess this is a bug on 2901, but want to confirm with you guys first. Now the whole config:
version 15.2
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname AEI_SV_Cisco_2091
boot-start-marker
boot-end-marker
logging buffered 51200 warnings
no aaa new-model
ipv6 unicast-routing
ipv6 dhcp pool HE
prefix-delegation pool HE-48
address prefix 2001:470:1F05:7A::/64
ipv6 cef
ip dhcp pool default
network 10.10.10.0 255.255.255.0
default-router 10.10.10.1
dns-server 10.10.10.1
ip dhcp pool dslam1
network 10.11.11.0 255.255.255.0
default-router 10.11.11.1
dns-server 10.11.11.1
ip domain name yourdomain.com
ip name-server 8.8.8.8
ip name-server 8.8.4.4
ip cef
multilink bundle-name authenticated
vpdn enable
crypto pki token default removal timeout 0
crypto pki trustpoint TP-self-signed-3962993046
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-3962993046
revocation-check none
rsakeypair TP-self-signed-3962993046
crypto pki certificate chain TP-self-signed-3962993046
certificate self-signed 01
3082022B 30820194 A0030201 02020101 300D0609 2A864886 F70D0101 05050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 33393632 39393330 3436301E 170D3131 31313232 31363132
31335A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D33 39363239
39333034 3630819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100E6AF 1640A998 F13E9F8B EB9E404C F0D6E105 8DE05E45 9C9C525A 5AAEAF59
456A4578 1C0E283C 39B3751D 3F362D64 13FACD69 A92C31BA 6D2EEFBE 52BCC70C
73359968 2F76B830 A978BD5F 9A86903F C12BB00B C35C47D1 BADBE727 773E205D
A839969D FE3854B3 26E93F21 63DC4E57 D4C44821 FBE88BAA 4A1D5565 DA416138
3A7D0203 010001A3 53305130 0F060355 1D130101 FF040530 030101FF 301F0603
551D2304 18301680 14BA6DEA 79E4742D 4878C88E D014C7A3 8022546A FE301D06
03551D0E 04160414 BA6DEA79 E4742D48 78C88ED0 14C7A380 22546AFE 300D0609
2A864886 F70D0101 05050003 818100CE C6732F7E 6AB385C5 5BF4E241 BE179F5D
E7C5CC78 2BFB33EC 3181D4D2 90981D2B 1106205F A3C5FEE8 E78A013B ABF3F5E0
52772A22 F3A0A24C C4F62DDB E2E6A21D AC75772B 6FEC9323 3DFC4165 CC645E62
5C8F5842 18B8DF5B C3E3C39C EBB60D3E E7ADA89B A72FB468 92F77F0A A33B5591
F5048271 F074C64E 38291F93 848F09
            quit
license udi pid CISCO2901/K9 sn FCZ15489123
username admin privilege 15 secret 5 $1$.CdN$d0DXERD9PqUtu6XPilTv/.
username chap password 0 chap
bba-group pppoe global
virtual-template 1
sessions max limit 256
interface Tunnel0
description Hurricane Electric IPv6 Tunnel Broker
no ip address
ipv6 address 2001:470:1F04:7A::2/64
ipv6 enable
tunnel source 173.13.177.215
tunnel mode ipv6ip
tunnel destination 72.52.104.74
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-GE 0/0$
ip address 10.10.10.1 255.255.255.0
ip nat inside
ip nat allow-static-host
ip nat enable
ip virtual-reassembly in
shutdown
duplex auto
speed auto
ipv6 enable
ipv6 dhcp server HE1
interface GigabitEthernet0/1
ip address 173.13.177.215 255.255.255.240
ip nat outside
ip nat enable
ip virtual-reassembly in
duplex auto
speed auto
interface FastEthernet0/0/0
ip address 10.11.11.1 255.255.255.0
ip nat inside
ip nat enable
ip virtual-reassembly in
duplex auto
speed auto
ipv6 address 2001:470:1F05:7A::1/64
ipv6 enable
ipv6 nd managed-config-flag
ipv6 nd other-config-flag
ipv6 dhcp server HE
pppoe enable group global
interface FastEthernet0/0/1
no ip address
shutdown
duplex auto
speed auto
interface Virtual-Template1
mtu 1492
ip unnumbered FastEthernet0/0/0
ip nat inside
ip nat enable
ip virtual-reassembly in
ipv6 enable
ipv6 nd managed-config-flag
ipv6 nd other-config-flag
no ipv6 nd ra suppress
ipv6 dhcp server HE
peer default ip address dhcp-pool dslam1
peer default ipv6 pool HE
ppp authentication chap
no routing dynamic
ip forward-protocol nd
no ip http server
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip dns server
ip nat source list 1 interface GigabitEthernet0/1 overload
ip route 0.0.0.0 0.0.0.0 173.13.177.222
access-list 1 permit any
ipv6 route ::/0 Tunnel0
ipv6 local pool test 2001:470:7007::/48 64
ipv6 local pool HE-48 2001:470:8008::/48 64
control-plane
line con 0
login local
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 4
privilege level 15
login local
transport preferred none
transport input all
transport output all
line vty 5 15
privilege level 15
login local
transport preferred none
transport input all
transport output all
scheduler allocate 20000 1000
end
See both IPv4 and IPv6 are using virtual template to get PPPoE work. Everything's working fairly well on IPv4. I can ping from cisco to the 10.11.11.x address on Actiontec router. But with IPv6, I can't ping 2001:470:1f05:7a:: address on Actiontec router. The correct route through virtual-access is not installed, or the F0/0/0 interface doesn't pass the IPv6 traffic to the corresponding virtual access interface:
AEI_SV_Cisco_2091#sh ipv6 route
IPv6 Routing Table - default - 7 entries
Codes: C - Connected, L - Local, S - Static, U - Per-user Static route
       B - BGP, R - RIP, I1 - ISIS L1, I2 - ISIS L2
       IA - ISIS interarea, IS - ISIS summary, D - EIGRP, EX - EIGRP external
       ND - Neighbor Discovery, l - LISP
       O - OSPF Intra, OI - OSPF Inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2
       ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2
S   ::/0 [1/0]
     via Tunnel0, directly connected
C   2001:470:1F04:7A::/64 [0/0]
     via Tunnel0, directly connected
L   2001:470:1F04:7A::2/128 [0/0]
     via Tunnel0, receive
C   2001:470:1F05:7A::/64 [0/0]
     via FastEthernet0/0/0, directly connected (this sounds correct, but I'm not able to reach client from this interface)
L   2001:470:1F05:7A::1/128 [0/0]
     via FastEthernet0/0/0, receive
S   2001:470:8008::/64 [1/0]
     via FE80::21F6:88C4:497E:6F9C, Virtual-Access2.2
L   FF00::/8 [0/0]
     via Null0, receive
Can some help? Thanks!
Henry

Hi,
The 'bug' i described above seems to apply only to packets the router generates itself. I tested it by creating a temporary subnet. Even though i had no end-to-end connectivity i could see packets matching the outbound acl which were created from a host on that subnet.
Carsten

Need Urgent Help on Meeting Place Integration with CUCM 7.1 and AS5400 PSTN Gateway

Hi,
This is first time I am on this forum.
I have already tried going through a lot of docs on docwiki.cisco.com but couldn't find complete configuration help.
I have to integrate Meeting Place 8.X with an existing CUCM and an E1 gateway (PSTN Gateway) AS5400.
The CUCM is already part of a Telepresence Environment. I need to create a SIP trunk between AS5400 and CUCM 7.1 and then create a Trunk between AS5400 and Cisco Unified MP 8.X and then between CUMP and CUCM.
I need help on AS5400 SIP Configs as well as parameters I need to cover on CUCM (Though I have done some basic dial-peer configs but they haven't been of much help).
Then I also need help on AS5400 SIP configs with CUMP 8.0
Any docs on Integration between CUMP and TP3000 will be of great help too.
Rgds,
Asim

I can get the Ricoh to register as sip endpoint, it answeres then imediatly disconnects. Doing a monitor with Wireshark looks like it attempts to negotiate t38 but fails. Any idea why this fails?
|160.260684000|         INVITE SDP (g711U)            |                   |SIP From:
|         |(5060)   ------------------> (5060)   |                   |
|160.338806000|         INVITE SDP (t38)              |                   |SIP Request
|         |(5060)   <------------------ (63435) |                   |
|160.339545000|         491 Request Pending           |                   |SIP Status
|         |(5060)   ------------------> (5060)   |                   |
|160.547894000|         406 Not Acceptable            |                   |SIP Status
|         |(5060)   <------------------ (63435) |                   |

Im changing my notebook and i dont want to lose my applications in the iphone

Im changing my notebook and i dont want to lose my applications in the iphone 5, so is there any way that i can back up and then restore in another computer, because in the past i have to delete all the content
thanks!

See the instructions wjosten has posted in the user tips section here: https://discussions.apple.com/docs/DOC-3141

Discussion Jabber on Notebooks and Cisco 2901 gateway

Similar Messages

Maybe you are looking for