Disk 250 gb 5400rpm went out of service, compac presario cq71-310sb which disk is compatible?

1. Product Name and Number : vl001EA#UUG
compac presario cq71-310sb notebook
2. Operating System installed : windows 7
3. Error message : "hard disk 1 quick (303)
4. Any changes made to your system before the issue occurred: no
5. In the subject title, include a brief, specific description of the problem,
Windows does not come up. I get a blue screen, with an arrow on it.
I assume that the disk is corrupt?
Which disk is compatible with mine?

Hi,
Please do a HDD test first:
1. Restart the computer.
2. Keep tapping the F10 key when the HP logo appears. This will take you to Bios Setup Utility.
3. Select the Diagnostic tab.
4. Select the "hard drive self test" option and press enter to perform the test.
Note: This test may take up to 40 minutes or more.
Pass - The hard drive is not damaged.
Fail - the hard drive is damaged and may need to be replaced.
Normal SATA 2.5" HDD from Samsung, Western Digital, Seagate, Hitachi .... can do the job. You can use bigger (capacity) too.
Good luck.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Similar Messages

The agent extension is out of service. error

The agent extension is out of service.
ready state change and call control operations cannot be performed.
The agent extension is back in service.
all operations are back in service.
I get this when the agent is just sitting there in a ready state.
CUCM 7.0 UCCX 7.0
I would appreciate any help you can offer.
Dave 404 569-1752
[email protected]

The most common cause of this was the agent's phone restarted or a CTI interruption occured. This is typically something to start troubleshooting on UCM side. The CAD Troubleshooting Guide says essentially the same thing:
Problem The agent’s state changed to Not Ready for no apparent reason.
Symptom. In some situations, an agent’s state may change to Not
Ready for no apparent reason.
Cause. To determine the reason, check the reason code:
..other causes removed...
■ If the reason code is 32759, the agent’s state became Not Ready
because the phone went out of service. Check to make sure the
phone is still functional and that you can call the phone directly. If
everything seems fine, it is most likely a temporary problem and the
phone has since recovered. If the phone is still down, it is most
likely a Unified CM problem. Please consult Unified CM support.
Solution In many cases, an agent’s state becoming Not Ready is not a serious
issue. Simply click Ready to change the agent’s state to Ready.
To determine the reason code, do one of the following:
...other solutions removed...
If the reason code is 32759, the agent’s state became Not Ready
because the phone went out of service. Check to make sure the
phone is still functional and that you can call the phone directly. If
everything seems fine, it is most likely a temporary problem and the
phone has since recovered. If the phone is still down, it is most
likely a Unified CM problem. Please consult Unified CM support.

I have a Moto G for Verizon Prepaid and my service ended so I bought a $35 card instead of the $50 one and my service went out in 2 days. Help?

I have a Moto G for Verizon Prepaid and my service ended so I bought a $35 card instead of the $50 one and my service went out in 2 days. Help?

You can't use a $35 card on that type of phone.

I lost my iPhone and when I'm trying to find it with the location, they say that it is "out of service". What should I do?

Hello people!
As I mentionned in my question, I have lost my iPhone I'm feeling very dumb, it is the second time that this happens to me and I really need your help! I don't even know what happened, but when I arrived home after school, I didn't find my phone. The fact is that I was sure to have take it with me, but I haven't, as I see. I went on the apple site: "location of my iPhone" and they told me that my cellphone was out of service. Now, I really don't know what to do and what to think. I serched everywhere, in my car, everywhere in my house, I even went outside to check, but i live in Quebec and it is snowing a lot this winter, so maybe I just didn't see it... Anyways, I'm really scared cause I have 3G on my phone and now they say that I'm not connected to 3G anymore, neither any other internet service. I'm freaking right now. Does that mean that my cellphone is broke, stuck in the snow, or just somewhere that I'm never gonna find out? I'm imagining all the worst possibilities so if you don't want me to die soon, please, help me (try to reassure me if it is possible but if is not, tell me the truth anyways).
Thank you guys the one who is gonna help is going to have my recognition forever!
Sabrina999
P.S.-I'm a french Quebecor so if you don't understand my writing, I'm sorry

You're welcome.
Voicemail is left at your carrier's server. That will continue to work unless you report your iPhone as lost or stolen with your carrier.
You may never find it again and you can't if the iPhone remains offline or out of service which means the iPhone is powered off or doesn't have cellular reception.

Last Wednesday my iPhone 4 shut down automatically and it wouldn't let me reboot for about a half an hour. It finally rebooted and then it started with the batterty drainage and no service, going in and out of service. What's wrong?

Hi everyone... Last Wednesday my iPhone 4 shut down automatically... I had battery. It took about a half an hour to reboot it. After that I started having trouble with going in and out of service and battery drainage. I do have that update 5 ios... or whatever its called... but I did that about 2-3 months ago and had no problems. I called Apple and they wouldn't do a **** thing for me. I called AT&T and they reset the network... didn't work. I did a hard shut down and didn't work. Now today, every call I had was dropped. So of course this morning when I woke up at like 8:30 am by 10:30 am my battery went from 100% to 35%. ***. Can someone help me???

Hi everyone... Last Wednesday my iPhone 4 shut down automatically... I had battery. It took about a half an hour to reboot it. After that I started having trouble with going in and out of service and battery drainage. I do have that update 5 ios... or whatever its called... but I did that about 2-3 months ago and had no problems. I called Apple and they wouldn't do a **** thing for me. I called AT&T and they reset the network... didn't work. I did a hard shut down and didn't work. Now today, every call I had was dropped. So of course this morning when I woke up at like 8:30 am by 10:30 am my battery went from 100% to 35%. ***. Can someone help me???

I have a lap top - pc - 10 yrs old - screen went out - how can I transfer pictures word directly to my Macbook pro retinal display 2013

screen went out on my 10 yr old dell xps m1710 - it appears to still boot - I can't see anything on the screen - I am looking ofr a way to directly access the hard drive pc to pc connection and do direct file transfers - tornado does not work c osx systems yet any otehr device out there? I have a lot of famiily pictures and some word files I want to transfer - nothing heavy. it is a screen/hardware issue not someting I can boot c in safe mode - still can''t see the screen and can't see to use a zip drive - I will need to use my new macbook pro 15 retinal display 2013 screen to "see" the files on the pc.
ideas?
Thanks
mhdmd53 -
usb to usb does not work nor does the tornado device - that is - so far - just pc to pc.

FireWire between the two (get appropriate 800-800 or 400-800), Target Disk Mode on the old one, appears as an external disk on the new one. Drag everything over, or use Setup Assistant if first start of new one, or plain old Migration Assistant. You really don't need a display to see a prancing FireWire icon, do you?
http://support.apple.com/kb/HT1661
http://support.apple.com/kb/HT4889
(with the added advantage that since you ain't booting anything off the drive, can turn the Mac on or off at will without risking data corruption on the drive)

CSCts69270 - CCX CTI ports may stuck in out-of-service state when UCM Upgrade/Restart

Symptom:
CCX CTI ports (RP & IVR) may stuck in out-of-service state during CUCM upgrade or Restart.
Conditions:
During CUCM upgrade the The UCCX CTI ports (RoutePoint Triggers and few IVR ports) went into out-of-service state .
This condition may happen during CUCM upgrade process or CUCM nodes restart. When this happens;
The CUCM sate of down ports is "Registered".
The UCCX state of down ports is "Out of Service"
This was tested on following Release branch;
CUCM Version: 8.6.2.10000-30
UCCX Version: 8.5.1.11001-35
JTAPI Version: 8.6(2.10000)-2
CUCM is a 15 Nodes cluster over the LAN with 10 subscriber nodes.
UCCX is a 2 Nodes-HA Cluster, with one Route point, and 300 ICT IVR ports.
Workaround:
After Upgrade completes, restart of CTIManager service from the CUCM nodes serving the CCX.
Last Modified:
Aug 26,2013
Symptom:
CCX CTI ports (RP & IVR) may stuck in out-of-service state during CUCM upgrade or Restart.
Conditions:
During CUCM upgrade the The UCCX CTI ports (RoutePoint Triggers and few IVR ports) went into out-of-service state .
This condition may happen during CUCM upgrade process or CUCM nodes restart. When this happens;
The CUCM sate of down ports is "Registered".
The UCCX state of down ports is "Out of Service"
This was tested on following Release branch;
CUCM Version: 8.6.2.10000-30
UCCX Version: 8.5.1.11001-35
JTAPI Version: 8.6(2.10000)-2
CUCM is a 15 Nodes cluster over the LAN with 10 subscriber nodes.
UCCX is a 2 Nodes-HA Cluster, with one Route point, and 300 ICT IVR ports.
Workaround:
After Upgrade completes, restart of CTIManager service from the CUCM nodes serving the CCX.
Last Modified:
Aug 26,2013
Known Affected Releases:
(0)
Known Fixed Releases:
(0)

Hello r.mata, do you have a question about this bug? Regards, Wes

A line of pixelation went out

It's a brand new iMac and a line of pixelation went out. It looks like it is bleeding from inside of the screen.

This sounds like a possible hardware failure, perhaps the graphics card or the display. If your machine is less than 90 days old or if you have already purchased AppleCare (highly recommended) give AppleCare a call. You can find the number in the owners manual. If you don't have AppleCare or the machine is older than 90 days old then make an appointment at your local Apple Store or AASP and take it in for service.

I tried to sync my iphone4 to my pc (not mac) and the following message went out: I tunescould not back up the iphone because an error occurred I restore my phone but nothing happened. What shall I do? (my ipad is working perfectly)

I tried to sync my iphone4 to my pc (not mac) and the following message went out: I tunescould not back up the iphone because an error occurred I restore my phone but nothing happened. What shall I do? (my ipad is working perfectly when i sync it)
I dont know why this happens.

Unfortunately, "because and error occured" doesn't give you much to go on. Some general things I would try if you haven't already:
Use Disk Utility on your mac to repair disk permissions, then reboot and try backing up again.
Use Finder to go to ~/Library/Application Support/MobileSync/, then control-click on the Backup folder and select Get Info, then check Sharing & Permissions at the bottom and make sure your username has read & write priviledges
Try closing all apps, then reset your phone: double-tap the home button, tap and hold the apps at the bottom until they wiggle, tap the minus sign on all apps to close them. Then reset your phone: hold the on/off and home buttons until you see the Apple logo (ignore the off slider that appears first), and release
Try a different usb to dock connector cable; ensure that your case isn't interfering with a good connection to the dock connector at the bottom of your phone; clean the dock connector at the bottom of your phone (e.g., with a dry toothbrush); troubleshoot your usb connection (http://support.apple.com/kb/TS1286)
I know this looks like a laundry list, but unfortunately it's hard to isolate the problem without a clear error message. If the problem persists, you might try posting in the iMac or iTunes forums for other ideas.

I think that I no have luck. My mac has many problems: the source burnt, the keyboard went out of order , the screen is full of spots and the last one was the battery which is no charging anymore. I am already spent a lot of money to get the mac in order

I am really disapointed with my MacBook Air. I bought it around two years ago and every three months I need to do something to fix it. First was my source, it did not work and need to buy a new one after searched in 5 shops in Brasília/ Brazil. After this was the screen, full of waves and dark spots. Next was the keyboard which went out of order and I need to change by a new one (20 days waiting for the service in Goiânia/Brazil). Now was the battery, which is not charging! And the support told me to change and more 20 days waiting for the repair. When I bought my first Mac I really think that I never have so many problems. Anyone has the same issues?
Best
Janine

Your dsplay is getting extended onto the external monitor. Chcnage the setting to duplicate it or only display on the external monitor and you should be fine,
Let me know if this worked for you.

Power went out and now spinning ball of death

This morning the power went out while I had been working in InDesign and Illustrator. I came in and saved the project before the back up power went out but did not get the Mac powered off completely before the back up stopped. When the power came back on, I restarted the mac and Indesign, and my project is now constantly getting the spinning ball of death; I can't even recover it anymore in Indesign (I can open the file, but the recovery was lost). ALL other programs are fine. Just indesign.
I went to look for help online and found a recommendation to turn everything off, unplug mac, let it rest then hold the power button down and replug the power then power the mac back on, and now my fan is running at super high speed and I still am having huge problems with InDesign. 1) can you tell me how to get the fan back to the way it was and 2) what do I do about spinny rainbow ball in Indesign.
HELP!!!!!

Welcome to the Apple Support Communities
For the fans issue, first reset the SMC > http://support.apple.com/kb/HT3964 If it doesn't work, it's possible that the computer has a hardware problem.
Apart from that, it's possible that your hard disk got damaged because of the power outage. To check if it's OK, open Disk Utility (it's in /Applications/Utilities), choose "Macintosh HD" in the sidebar and verify the disk. If it shows a problem, start in OS X Recovery (hold Command and R keys while your computer is starting), open Disk Utility and repair the Macintosh HD partition. If it couldn't be repaired, the hard disk has to be replaced

IMac went out and won't come back on

I ask this question on behalf of my father who doens't live in the same town as me. He was at his computer (iMac, 21.5 inch screen, OSX Mountain Lion 10.8.4) during a thunderstorm and it suddenly went out. He said there was a flash of light and then it went out. I told him to unplug it, re-start the power strip then try to turn it on which he did and it wont' come on. HIs land-line telephone is also out but, their carrier is AT&T and the internet is serviced by Time Warner. Does anyone have any idea what might be happening? Hopefully is computer didn't suddenly die. Thanks in advance :-)

Ouch, it sure sounds like the Mac died, is there an Apple Store or AASP where he'sat to look at it?

Electric went out, now there's a question mark blinking on my screen...

Electric went out, now there's a question mark blinking on my screen...

Try restarting your Mac while holding down the Option key.
Hopefully you'll see the Startup Manager window where you can select the statup disk and click Restart.

My iphone 5c screen went out and its just a black screen ive tryed a hard reset and nothing still when i plug the charger in it dings and ive hooked it to itunes and restored it still nun do i need to buy a new screen or is something else wrong?

My iphone 5c screen went out and its just a black screen ive tryed a hard reset and nothing still when i plug the charger in it dings every few secs and ive hooked it to itunes and restored it still nun do i need to buy a new screen or is something else wrong?

If your iPod Touch, iPhone, or iPad is Broken
Apple does not fix iDevices. Instead, they exchange yours for a refurbished or new replacement depending upon the age of your device and refurbished inventories. On rare occasions when there are no longer refurbished units for your older model, they may replace it with the next newer model.
ATTN: Beginning July 2013 Apple Stores are now equipped to do screen repairs/replacements in-house on iPhone 5 and 5C. In some cases while you wait. According to Apple this is the beginning of equipping Apple Stores with the resources needed to do most repairs for iPhones, iPads, and iPod Touches that would not require major replacements. Later in the year the services may be extended as Apple Stores become equipped and staffed with the proper repair expertise. So, if you need a screen repaired or a broken screen replaced or have your stuck Home button fixed, call your local Apple Store to see if they are now doing these in-house.
You may take your device to an Apple retailer for help or you may call Customer Service and arrange to send your device to Apple:
Apple Store Customer Service at 1-800-676-2775 or visit online Help for more information.
To contact product and tech support: Contacting Apple for support and service - this includes international calling numbers.
You will find respective repair costs in the appropriate link:
iPod Service Support and Costs
iPhone Service Support and Costs
iPad Service Support and Costs
There are third-party firms that do repairs on iDevices, and there are places where you can order parts to DIY if you feel up to the task:
1. iResq or Google for others.
2. Buy and replace screen yourself: iFixit

Macbook monitor went out. Driver issue?

About 8 months ago my macbook monitor went out. Since then I have been using an external monitor. This week I booted to a Linux live CD (Kubuntu) and the monitor worked just fine.
I would appreciate any suggestions or direction with this.
Seems to be a simple driver problem. I have checked the Intel and Apple websites to see if there was a driver and couldn't find anything.

Hi xenogy, and a warm welcome to the forums!
First try a Safe Boot, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, reboot when it completes.
(Safe boot may stay on the gray radian for a long time, let it go, it's trying to repair the Hard Drive.)
It also tries to load a "safe Video Driver".
Get Pacifist...
http://www.charlessoft.com/
then extract what you need from your Install Disk.
Or, a relatively painless Archive & Install, which gives you a new/old OS, but can preserve all your files, pics, music, settings, etc., as long as you have plenty of free disk space and no Disk corruption, and is relatively quick & painless...
http://docs.info.apple.com/article.html?artnum=107120
Just be sure to select Preserve Users & Settings.

Disk 250 gb 5400rpm went out of service, compac presario cq71-310sb which disk is compatible?

Similar Messages

Maybe you are looking for