Disk error message on Sun StorEdge 3310.

Hi guys,
Does anyone see the following error message in the /var/adm/messages? Should I have to replace this faulty disk?
Mar 6 11:06:21 balrog scsi: [ID 107833 kern.warning] WARNING: /pci@1d,700000/sc
si@1/sd@5,0 (sd36):Mar 6 11:06:21 balrog Error for Command: write(10) Error Level:Retryable
Mar 6 11:06:21 balrog scsi: [ID 107833 kern.notice] Requested Block: 5491072 Error Block: 5491079
Mar 6 11:06:21 balrog scsi: [ID 107833 kern.notice] Vendor: SEAGATE
Serial Number: 0447B9LRDV
Mar 6 11:06:21 balrog scsi: [ID 107833 kern.notice] Sense Key: Hardware Error
Mar 6 11:06:21 balrog scsi: [ID 107833 kern.notice] ASC: 0x32 (no defect spare location available), ASCQ: 0x0, FRU: 0x4
Looking forward to your comments.
Jeff.

A good output that would give you a hint of a problem is iostat -En
This output reports anykind of errors to a particular disk since the last reboot. If you are seeing high error numbers, then you can move onto running a file system check - fsck - on the drive.
If you have anykind of RAID setup, check to see if any issues are being reported. Depending on what you are using to manage the RAID - Veritas Volume Manager or Solaris Disk Suite - they will most certainly tell you if there is an issue. A vxprint for Veritas and a metastat for DiskSuite will show you what you have setup and if there are any recognized disk issues.

Similar Messages

  • Veritas Volume manager 4.0 with Sun StorEdge 3310 D

    I am running into a problem. The vxconfigd deamon always dump core when rebooting.
    Our environment is listed below.
    OS environemt.
         SunOS server1 5.8 Generic_117350-43 sun4u sparc SUNW,Sun-Fire-V240
    Software installed.
         Sun Cluster 3.0
         Veritas Volume Manager 4.0 MP2.
    Disk Array associated.
         Sun StorEdge 3310 D.
    I looked up veritas.com and find Array Support Library (ASL) for Sun StorEdge 3xxx Series is recommended. But I didn't find this library is running on this server.
    Please refer to this following link
    http://support.veritas.com/docs/277923
    As our system is one of critical systems and I'd like to confirm that I can follow up this procedure without doing harm things to our system.
    Jeff

    No problem Jeff :)
    I took a look at the Veritas doc and you're right it does seem to cover everthing.
    Has the vxconfigd core dumped since the start? ie from the moment it was installed?
    I have installed VXVM 4.0 with Solaris 8 but without the ASL and this worked ok, I know that's not much help to you but I am not sure the ASL will help. Mind you I have not installed it with Sun Cluster 3.0.

  • No Disk error Messages in PSE8

    On and off I keep getting the following error message when I switch between Edit and Orgainzier in PSE8
    and sometime other times.  Photoshop ElementsOrgainzer.exe-No Disk    There is no disk in the
    drive.   Please insert a disk into drive \Device\Harddisk4\DR4.
    I have to hit Cancel 3-4 times to get rid of it.
    What is this and how do I stop it?  Tks. ALan

    I have recently experienced this message repeatedly in PSE6 running on Vista. I believe after either saving a file from PSE6 to a floppy in drive A or opening a file in PSE6 from an SD memory card in drive J. Resolved by recreating both situations then ensuring that i used photoshop to open files from and save files to the resident C drive before removing the floppy disk from drive A and using the 'safely remove hardware' function in Vista to confirm that it was safe to remove the SD card.
    Following this procedure I have experienced no more 'no disk error messages'

  • Disk error message in Organizer

    When I open Organizer in Acrobat Pro 9, I get a No Disk error message:
    "There is no disk in the drive. Please insert a disk into drive \Devise\Harddisk\DR1" with buttons to Cancel, Try Again, Continue.
    If I cancel [and I have to cancel twice for each error message, the message changes to ...Harddisk2\DR2 through to Harddisk4\DR4.
    I always get there in the end, but how can I stop the error messages appearing in the first place? It's incredibly irritating!
    There are no preferences for Organizer, and nothing I can see in the Acrobat preferences that would help.

    I'm surprised PS even runs on that computer although of course 5.0 LE is pretty old.
    A 165 MB file may just be too much for it.
    How can you "set your c drive to 4096MB"? Do you mean Paging file?
    We need someone with a long memory to chime in, but you do need to clarify what you are doing.

  • "Missing Disks" Error Message - Unable to open FCP

    Every time I tried to open FCP, a "missing disks" error message shows up and prevents me from opening the application. It says, "To preserve the integrity of the date used by Final Cut Pro, it is necessary to ensure the existence of the following path(s):" and it says "Macintosh HD is offline." There are two options for the error message, "Check Again" or "Reset Scratch Disks." When I click "Check Again," nothing happens. When I click, "Reset Scratch Disks", it takes me to a "Scratch Disks" window, which shows, "9.8GB on Macintosh HD is offline." I click "OK", but it only takes me back the same "missing disks" error message. What should I do to solve this error and open FCP?
    Thanks in advance.

    Hi -
    If you are mid-project, then first I would find your project file and make a duplicate by Control-clicking on it, and selecting Duplicate. You can rename that new file so it is easy to remember. Once that is done, you have a protection back up of your project file so that whatever happens, you can recover back to this point in your project by opening the duplicated file.
    Selecting (or Re-Selecting) a Scratch Disk does not affect what has been done in a project's past, it will only affect what FCP will do once it is launched and where it will place media and renders as you go forward.
    A bigger concern/interest to me is why the disk Macintosh HD is offline, since Macintosh HD is usually the name of the internal system disk on your computer.
    Have you renamed your internal hard disk (either intentionally or unintentionally)?
    Do you have external disks connected to your computer?
    Have you installed any new software - like Snow Leopard, or Fusion?
    If you have had the disk Macintosh HD selected as your scratch disk all throughout your project up to this point, it is likely that the disk Macintosh HD has your captured footage and renders. So . . . if it is off-line as a scratch disk, once you reset your scratch disk to an available drive and open your project, it is likely that the project will show that all your media, which it previously associated with the missing disk is offline as well.
    If that is the case, you will need to reconnect your media and re-render your renders. This can be done by selecting your offline clips and Control clicking on one of them and selecting Reconnect Media . . .
    *If you are not feeling confident about proceeding, I would recommend a trip to an Apple store to get someone to walk you through the process.*
    Hope this helps.

  • Sun Storedge 3310

    I would like to know if it is possible to connect a sun storedge 3310 array to windows server 2012 r2? If ther is could you tell me how. I know how to do it on server 2003 but 2012 r2 is much different.

    Hi,
    I would like to know if it is possible to connect a sun storedge 3310 array to windows server 2012 r2?
    Since we are not familiar with the product you have mentioned, I would suggest you contact corresponding vendor support to get more specific and accurate response.
    Thank you for your understanding and support.
    Best Regards,
    Amy
    Please remember to mark the replies as answers if they help and un-mark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected]

  • Connecting to a Sun StorEdge 3310

    Hello all,
    in our warehouse I've found a Sun StorEdge 3310. I want to try to use it but I do not have any kind of usefull serial cable. Also StorEdge has a LAN port but I'm not able to find a mac address to force ARP table and telnet it.
    Any hint to get my storage accessible?
    Thanks
    Stefano
    http://www.stefanocislaghi.it

    Please have a look at the installation document http://docs.sun.com/app/docs/doc/816-7290-19 and feel free to get back here if you still have questions.

  • Sun storedge 3310 fw 4.1.5f MIB ?

    Hi does anybody know where can I find the MIB snmp file for Sun storedge 3310 fw version 4.1.5.f ?
    Thanks

    Nevermind the last posts, I forgot to install the 32 bit drivers of ultra 3 card.
    Anyway thanks to anyone who might have thought about this.
    Orlando

  • Multi-initated LUNS on Sun StorEdge 3310

    I recently received two Sun V20Zs and a StorEdge 3310, and I am asked to cluster these two machines with the 3310 as shared storage. 3310 came with two raid controllers.
    My question is, could I create multi-initiaged LUNs and have these LUNs mapped by the V20Z. Reason behind having the multi-imitated LUNs is it will facilitate fail-over in case a one of the V20Z are unavailable.
    V20Zs are running Fedora Core 3.
    Thanks for your help.

    A good output that would give you a hint of a problem is iostat -En
    This output reports anykind of errors to a particular disk since the last reboot. If you are seeing high error numbers, then you can move onto running a file system check - fsck - on the drive.
    If you have anykind of RAID setup, check to see if any issues are being reported. Depending on what you are using to manage the RAID - Veritas Volume Manager or Solaris Disk Suite - they will most certainly tell you if there is an issue. A vxprint for Veritas and a metastat for DiskSuite will show you what you have setup and if there are any recognized disk issues.

  • Windows - No Disk error message when connecting Ipod to computer

    I recently connected my Ipod to the Computer as I have done for the last year and I am now getting an error message reading: "Windows - No Disk". It then asks me to insert a disk. I cannot cancel out, continue or retry which are the three choices. I eventually have to Ctrl + Alt + Del to close out Itunes. Can anyone help? Thank You.
    Dell XPS   Windows 2000  

    I have been ejecting it. This problem only began recently. I read through about 30 pages of this forum and found someone postoing about the same problem. They said it may be McAfee Viruscan in the background.I'll check that out.

  • "Windows - No Disk" error message on file transfer

    Hello!
    I updated our ZDM7 server from plain old ZDM7 with no updates to ZDM7 SP1
    IR1. Now, when initiating File Transfer operation with any workstation, up
    comes this error message:
    "Windows - No Disk"
    "Exception Processing Message c0000013 Parameters 75b6bf9c 4 75b6bf9c 75b6bf9c"
    [Cancel] [Try Again] [Continue]
    If I click "Continue" 4 times, file transfer starts up successfully.
    Any ideas about how to get rid of this annoying message?
    Toomas Aas

    Toomas,
    It appears that in the past few days you have not received a response to your
    posting. That concerns us, and has triggered this automated reply.
    Has your problem been resolved? If not, you might try one of the following options:
    - Visit http://support.novell.com and search the knowledgebase and/or check all
    the other self support options and support programs available.
    - You could also try posting your message again. Make sure it is posted in the
    correct newsgroup. (http://support.novell.com/forums)
    Be sure to read the forum FAQ about what to expect in the way of responses:
    http://support.novell.com/forums/faq_general.html
    If this is a reply to a duplicate posting, please ignore and accept our apologies
    and rest assured we will issue a stern reprimand to our posting bot.
    Good luck!
    Your Novell Product Support Forums Team
    http://support.novell.com/forums/

  • 'No Disk' error message on Photoshop startup

    Recently I have been receieving the following error message when Photoshop CS6 x64 srtarts up on my Windows 7 machine. Ps resides on my SSD.
    I don't always get the message but when I press X, Cancel, Try Again, or Continue the message repeats until finally Ps starts. I'm not sure what drive \Device\Harddisk3\Dr3 is supposed to mean. Does anyone have a clue what Ps is complaining about?

    I realize this is a mighty old thread, but I've recently had the same issue with Illustrator CSS 2014, and this is the only thread I could google that dealt with it.
    I scratched my head for a while on this, but I think I figured out the issue. At least I think I figured it out on my end. The error comes from the "recently opened" menu as far as I can tell. I had an old external hard-drive that I was browsing some old work on. I unplugged it when done and continued to go along with my newer work the next day. When I attempted to save my newer work in Illustrator, I got the "no disk" message several times, but powered through it with "try  again" till it saved.
    I'm thinking the error is just the system bumping the file that I had recently opened and now cannot locate slowly down and eventually off the "recently opened" menu. Not sure why Windows is smart enough to bypass this error sometimes and not others with most portable drives, but perhaps its an issue with how old this drive was, or perhaps because I did not properly eject the drive. Networked drives being connected and not connected may cause a similar issue. Not sure.

  • "Can't read or write to disk" error message

    hi...
    got my husband a 16g nano and i'm trying to sync his songs. i have the newest version of itunes installed. it put almost half of the songs on the nano and all of a sudden itunes has an error that says something about "can't write to nano. disk is not readable or writeable." i can view the nano contents, but i can't add to it and it will not let me sync it anymore.
    does anyone have any suggestions? thanks!

    thanks jason,
    i looked at the tips page you suggested and i tried it again on my new laptop and it still won't work. i'm going to try to restore it and then put it on the laptop again, hopefully that will work.
    the odd thing is it will start to sync and it comes up with the error message about half way through syncing (half the songs do make it to the ipod.) why can't it sync the whole way?? i'm perplexed.

  • Importing CD - No Disk Error Message When Ejecting CD

    Every since I upgraded my itunes to the latest version, I am getting an error message telling me there is no cd every time I eject my cd after importing. It gives me an option to retry, continue and cancel. No matter what I pick it does not recognize the next cd and my windows cursor is stuck in a rotating hourglass position even after I end the itunes program! Can anyone please shed some light? Thank you!

    Thanks Bob! My problem was that I was following advice from elsewhere on the internet that said I should burn a DVD in UDF format when in fact just burning it using disk utility in ISO made it work. Thank you so much!

  • "Disk error" message on install

    I have a CD for Windows XP Pro. I ran the BootCamp partition and the first part went smoothly. After I restarted to finish the install, I got this message in a DOS formatted screen...
    Disk error
    Press any key to restart
    When I press a key, nothing happens. I have to restart and select OSX to get my computer back up.
    Any suggestions?

    Shaun:
    Read *[_THIS ARTICLE_|http://docs.info.apple.com/article.html?artnum=306504]* written by Apple to address this issue. There are several threads on these forums discussing this issue and one of them is [HERE|http://discussions.apple.com/thread.jspa?messageID=6210710&#6210710].
    *[_THIS THREAD_|http://discussions.apple.com/thread.jspa?messageID=6560499&#6560499]* discusses the entire issue in details and provides a solution.
    Let me know how it goes and good luck.
    Axel F.

Maybe you are looking for