Disk utility doesn't see internal HD

A friend gave me a 17" Late 2006 Core 2 Duo, iMac 5.1, model MA590LL, it was working fine.
Donor asked me to zero out data before I used it so I did with Disk Utility. about 3/4 of the way through it hung up. I restarted it and now, starting up from the original install discs (10.4.7) hard drive will not show up anywhere in disk utility or as a destination volume for the OS reinstall.
Did the HD die during zeroing data?
if so what type replacement do I need? The original was 160gb which was plenty for the use this will see. Is all I need a 3.5 SATA HD?
thanks,
Rob

Thanks Niel,
I see the I can get a 160GB 3.5" SATA pretty cheap from Amazon, I really don't need anything more than that. Do I need to match rpm (7200 or 10,000), cache size (8mb or 16mb) and transfer (1.5Gb/s or 3gb/s) rate also?
If so where can I find what the originals were?
Are the connectors standard?
thanks,
Rob

Similar Messages

Macbook Pro: Disk Utility doesn't see my HD

Hi guys,
My Macbook Pro has been running slower lately, but I honestly didn't think too much about it...until today. It's just over a year old, running Mac OS X, and I mostly use Safari as my browser, but I have to use Firefox for my online classes. Today, Firefox froze up and quit responding, so I Force Quit it. A few minutes after this, Safari did the same thing, and then it was my entire desktop. Nothing was responding; I had to shut down by pushing the power button.
And then, it wouldn't turn back on. The chime sounded, the apple appeared, and the spinning circle underneath it. And it spun, and spun...until a generic "stop" symbol replaced the apple logo. I immediately shut it back down and did an online search. I followed every fix recommended for this issue. I tried reseting the PRAM, and then the SMC, and still the same thing happened. I tried to boot in Safe Mode, and if seemed to be working...right up until an hour passed and nothing new was happening. I shut it down again, and tried booting from the install disc of Snow Leopard. That worked, and I tried to do Disk Utility with the intention of following the online apple directive of running first aid on my HD. Except Disk Utility doesn't see my HD, only the boot disc and DVD drive. I'm guessing this is a bad sign. I tried calling Apple Care, but they are closed right now. I will call them in the morning, but in the meantime, I thought I'd see if anyone here had any advice I haven't already tried. Sadly, I haven't run Time Machine in...months. I'll end up losing a lot of stuff because I just didn't do that if my HD is toast.
Any suggestions?

Sure seems to be a failed(ing) hard drive. If you happen to get it into safe mode again, the ONLY thing you should immediately do is copy off your Home folder to an external USB disk, SD card, something. Then just get it to an Apple store for check.
Try to copy your files off first and don't try anything else to get at that disk until you copy your home folder. If the disk is failing and you're trying to do things to it you'll loose the chance to get that data.

Airport Disk Utility Doesn't See External Drive, But Airport Utility Does?

Hey! I am a recent Apple convert and just got a brand new MacBook and Airport Extreme. I am trying to get my Maxtor OneTouch 320GB HDD to work with the Extreme, but to no avail. The Airport Utility sees my HDD, but the Airport Disk Utility doesn't? Any hints/tips on how to fix this problem? Any help is appreciated! Thanks!

All I can think of is that the drive is formatted in NTFS which I have heard cannot be read by the AEBS(Airport Extreme Base Station), but I am confirming this right now in a different message. If you can copy the files, format your drive in HFS+(the Mac's standard file system), then reload the files. See if it works and reply back.

Disk Utility doesn't see Time capsuleDisk

I'm trying to migrate a backup did with Time Machine to a brand new Airport Time Capsule Disk.
This is for don't loess the previous backups having ones new.
I got some information and it looks I should connect both disks (old HD and new Time capsule) to my Mac , then restore the new one using as source the old backups.
The matter is that DISK UTILITY APP doesn't see the Time Capsule disk .
Who may help me in doing this operation?
Many thanks
ivano

Niel, many thanks for your reply. I've gone trough the instructions you've indicated but I've not found my case.
Let me try to explain my situation
Till now I did the backups in an external Western Digital HD (MyBookLive) using Time Machine.
The disk was gonna be full so I bought a Time Capsule bigger than the WD I had.
My intention was to continue to do backups using TimeMachine on the new TimeCapsule KEEPING ONLINE the old backups.
I read that I should use DISK UTILITY APP and restore the old spares bundle file into a new one locate into the Time Capsule.
My problem is that using DISK UTILITY I cannot see both the WD Disk neither the Time Capsule .
Many thanks in advance for your support
ivano

Recovery system disk utility doesn't see errors reported on startup volume

When I check for disk errors on my macbook pro, disk utility runs ~5 minutes, then quits, reporting errors:
2013-11-21 07:46:27 -0600: The volume Macintosh HD was found corrupt and needs to be repaired.
2013-11-21 07:46:27 -0600: Error: This disk needs to be repaired using the Recovery HD. Restart your computer, holding down the Command key and the R key until you see the Apple logo. When the OS X Utilities window appears, choose Disk Utility.2013-11-21 07:46:27 -0600:
2013-11-21 07:46:27 -0600: Disk Utility stopped verifying “Macintosh HD”: This disk needs to be repaired using the Recovery HD. Restart your computer, holding down the Command key and the R key until you see the Apple logo. When the OS X Utilities window appears, choose Disk Utility.
2013-11-21 07:46:27 -0600:
When I start up with the Recovery HD and run disk utility, it runs ~30 seconds and reports no errors.
Any suggestions for what to do next?

Seems to me something must be wrong, given the different reports. Not so? Mail in outlook has gotten slow, but who knows what that means. Can I startup wth an older OSX disk and try the disk utility from that?

Disk Utility not finding new internal hard drive

Hi All
My internal hard drive died recently and I replaced with a western digital drive from newegg..
All the cables are hooked up correctly, including the orange cable attached to the hard drive. Problem is that when I go to install OS X, Disk Utility doesn't even list the drive. Is there something I need to do beforehand? Anyone have any ideas as to why Disk Utility isn't even seeing the drive? Jumpers maybe?
Thanks in advance.
-Aaron

I doubt that any jumpers are needed, since this is the only (master) drive in the system. WD's site has pretty good info on this. Verify for yourself however.
Also, from their site:
How to partition and format an internal slave drive or an external drive in a Mac OS X (all versions).
Answer
In Mac OS X, you can use the built in Disk Utility to partition and initialize the drive so it will appear on the desktop.
1. Open the main drive (the drive that contains the operating system).
2. Open the Applications folder.
3. Open the Utilities folder.
4. Select Disk Utility.
5. The drives are displayed on the left side of the window. Click on the drive that you wish to partition (the top drive listing for the hard drive that you want to work with).
6. Once the drive is selected click on Partition.
7. Click on the Options button to select the partitioning scheme.
8. Click on Apple Partitioning Scheme or Apple Partitioning Map and then click on the OK button.
9. You will see several options for setting up the drive. Once you have selected the number of partitions, the format type you want, and a volume label, click the Partition button.
10. Following the completion of this process, the drive will appear on the desktop.
Joe

Disk Utility doesn't recognize HD. Installed new one, same problem.

Hello,
I have a MBP. It suddenly wouldn't boot up, and had the flashing question mark folder upon starting up, so I figured that the HD needed to be replaced. I ordered a brand new drive, and when I try to install Leopard, it doesn't see the new hard drive. I open Disk Utility to partition the drive to GUID, but Disk Utility doesn't even see the new drive. Just my optical drive is listed.
I hooked up the old hard drive externally to another mac, and it appears to be working just fine. So it isn't a bad drive as I had originally thought.
What else could be wrong? The laptop fails to see any internal hard drives. Is there anything else that I can do to fix this problem? Thanks.

Purely conjecture, your serial ATA controller may be bad (or the cable). I assume nothing shows in System Profiler/Hardware/Serial-ATA either. Maybe try the SMC reset?
-If the computer is on, turn it off.
-Disconnect the AC Adapter and remove the computer's battery.
-Press and hold down the power button for 5 seconds and then release the button.
-Reconnect the battery and AC Adapter.
-Press the Power button to restart the computer.

Lion Disk Utility doesn't finish erase

Since installing Lion (clean install) disk utility doesn’t finish erasing or partitioning external disks. I used the disk utility from the install drive to erase the internal drive before installing Lion, this worked fine, but ever since it failed to erase any of my external drives. It starts of as normal but the progress bar stops half way and just never finish. Disk Utility does respond.
I tried different format options, repair and verify but none of the processes finish.
I went back to the install drive that I used to erase the internal drive before Lion install and it also didn’t want to finish.
I copied the old disk utility from Snow Leopard to my desktop, it opens with a warning, but gives the same outcome.
Any advice?

I'm having the same problem on my late 2010 Air with Lion installed over Snow Leopard.
I've tried several usb memory drives and several external harddrives...all the same problem with the progress bar getting stuck halfway. wether I select 'partition' or 'erase'.
the 'genius' at the mac store told me that he advises a clean install of Lion. I did...or I thought I did but all my files were still in place and the problem was still there. Guess I will have to wipe the drive first.
Also, unable to repair permissions on the MAC drive.
But it is remarkable how few people seem to experience this problem thus far. A google search hardly returns any results.

Disk Utility doesn't refresh when inserting new DVDs

I'm in the process of copying a few DVDs by making an image of them first and then burning the image onto a blank DVD through Disk Utility.
After I'm done with one and insert a new DVD to copy, Disk Utility doesn't refresh to show me the new disk is in the drive. Is it normal?
If it is, is there something I can press so that Disk Utility manually refresh its listing of drives?
I find that quitting and restarting Disk Utility just to make a new image is so inefficient.

I am suddenly having the same problem. When I insert a blank disc either cd or dvd it does not show up in the left column in disc utility. I have tried closing and then relaunching disc utility but nothing. The disc shows up on my desk top but not in disc utility. I fear this is a Snow Leopard problem. Toast has no problem recognizing the disc and burning to it.

IPod Shuffle not recognized, device not recognized, disk utility doesn't...

...disk utility doesn't show up.
It's all on my wife's computer as it's her iPod. Up until yesterday - and she didn't change ANYTHING - iTunes 7.01 had no problem wiht the iPod. Today, however, iTunes nor her Mac recognizes the iPod. Can't do a thing with it. It displays a nice green light, but that's it. All connections checked and re-checked. Looked at the disk utility and there's no image for her iPod.
I plugged it into my own Mac and iTunes 7.02 tries to upload/access her library from her iPod and 1) after an interminable wait, say four to five minutes, it recognizes that there's a shared library available, and 2) then it says there's some firewall that won't let iTunes access the liberary.
I don't have an iPod of my own, so my experience is really limited. She uses her iPod all the time and, again, hasn't done anything different than she did last night.
What is to be done? Thanks in advance for GOOD tips.

Turns out she's running iTunes 7.1...
Still nothing.
Anyone out there, please?

Disk Utility doesn't recognise inserted DVD-R DL

I upgraded to Leopard from Tiger a few week ago and Disk Utility has been working fine for a while. I bought a few blank DVD-R DL disks with 8.5Gig storage capacities, but, when inserted, Disk Utility doesn't show them in the top of the pane on the left side.
It shows the Super Drive, but doesn't show an inserted DVD below it like it usually should.
Any suggestions?
Message was edited by: jemorris55

Alright, so instead of burning to the disk specifically, I burned to the superdrive which automatically burned to the disk. It worked alright and now that the DVD has something on it, its icon pops up in Disk Utility. I don't know why it chenged...

I am connected to time capsule via wi-fi but air port says not connected and disk utility does not see it

I am connected to time capsule via wi-fi but air port says not connected and disk utility does not see it. I had it connected via ethernet and it still did not see it. Then i disconncectd it from ethernet and did the Wi-fi connection and am able to post this message but air port still does not see it.

Disk Utility will not "see" the Time Capsule, so no need to waste any more time on that issue.
but air port still does not see it.
Not sure what you mean by "air port" here.

G4 disk utility does not see hard drive

I am helping someone with a G4 Quicksilver. She is running 10.4 but only has disks for 10.1 and 10.2. When I boot with the 10.2 CD, disk utility does not see the hard drive. I was thinking of connecting her computer to my MacBookPro (Intel, 10.5) via target disk mode and then running Disk Utility. Is that crazy? She is suffering from slow startup and grey screen. I've disconnected the periferals, safe booted, reset PRAM. She really needs Disk Utility.

with the 10.2 CD, disk utility does not see the hard drive.
Disk Utility from 10.2 should see the hard drive (the drive name should appear in the left box). If it does not, the drive is malfunctioning or has a loose cable.
If you attempt to Verify, it will complain that there are illegal values in reserved fields in several different record types. Using this older Disk Utility to repair a 10.4 disk may cause more problems than it solves.
As Tom \[Texas Mac Man] says, you should only repair 10.4 and later disks with 10.4 and later Disk Utility:
HT2648- Only use Mac OS X 10.4-compatible disk utilities with Mac OS X 10.4 volumes
• If you boot the regular Hard Drive (no CD/DVD required) while holding down the Shift key, it will do a quick check of the Hard Drive, then boot up in "Safe Mode". This will fix any simple Disk problems.
• 10.4.3 and later can do a Disk Utility Verify of the Boot drive, "live" (but cannot Repair "live").

Disk utility does not see network drive

I am trying to partition two NAS; however, they do not show up on disk utility but only the internal HD and a second external drive connected with USB.
I would appreciate ideas how to resolve this problem
Thanks

The Disk Utility isn't supposed to list network drives in its sidebar. Network drives can only be partitioned through disk images or software provided by the drive's manufacturer for that task(if any).
(61436)

Airport Utility doesn't see functioning Airport Extreme Base Station

I have an Extreme (n) Base Station which serves as a WDS main with one relay Express and one remote Express. All three are functioning properly. Now I want to add a second remote Express paired with the main Extreme. However, Airport Utility doesn't see the Extreme, even when hardwired. So I have no way to add in the Apple ID of the new remote.
Any suggestions on how to resolve this? Is it necessary to restore default settings on the Extreme and reconfigure EVERYTHING?
Thanks.

Not yet. Hoping there is some other approach, since if I reset it and then it loses the connection before configuration is complete, I lose the functions that are working now.

Disk utility doesn't see internal HD

Similar Messages

Maybe you are looking for