Display and hold

I just got an Ipod Nano 7th Gen. and I can't figure out how to put the device in "hold" position like previous models. In addition to that, is there a way to keep the display on full time? I use it in the car and after a minute or so the screen dims and then goes black. I have to push the home button to see what being played or to go to or back to the next tract. I was using my Iphone as my music device and you have the option never to turn the display off. I used that when i was playing music. Please let me know. It's very inconvenient to have to keep pressing those buttons.

Steve,
I do not know of any Hold feature on the meters. To my knowledge, only the red (overload) will "hold." Maybe I am about to learn something.
One could Normalize to -6db, but then I am NOT a fan of Normalizing in either PrPro, or Audition.
In Audition, the Waveform Display is more accurate than the representation I see in PrPro. There, it's pretty easy to graph the peaks and see where they fall (or "rise"). Do not know how SoundBooth displays, and if it's any more accurate, than PrPro. Now, PrPro is not bad, I just find it a bit more of an emulation, than what one has in Audition - maybe it's just my eyes... ?
Good luck and hope that someone knows of a display Hold.
Hunt

Similar Messages

Is there a way to get the highest audio peak to display (and hold) in PPro CS4?

I have to deliver my projects to a client with the audio mixdown at a specific level, namely, no greater than -6db. It would be great if, while playng back the sequence, the Master level would show, and hold to peak audio level reached. As we know, the peaks do indeed display, but disappear almost as fast as they appear, so it doesn't do me any good. There are two problems for this: 1. I must be blind, or something. 2. My mind doesn't work fast enough to notice where the little yellow bar appears, and then remember it at the end of the clip. HELP. Thanks, Steve.

Steve,
I do not know of any Hold feature on the meters. To my knowledge, only the red (overload) will "hold." Maybe I am about to learn something.
One could Normalize to -6db, but then I am NOT a fan of Normalizing in either PrPro, or Audition.
In Audition, the Waveform Display is more accurate than the representation I see in PrPro. There, it's pretty easy to graph the peaks and see where they fall (or "rise"). Do not know how SoundBooth displays, and if it's any more accurate, than PrPro. Now, PrPro is not bad, I just find it a bit more of an emulation, than what one has in Audition - maybe it's just my eyes... ?
Good luck and hope that someone knows of a display Hold.
Hunt

Hi, I'm trying to shut down the phone in the normal way (the Sleep / Wake button and hold down on the Close tab) turns off the display after a while yet, but the phone turns off completely opens up the phone to come out after the apple logo .. What is the

Hi, I'm trying to shut down the phone in the normal way (the Sleep / Wake button and hold down on the Close tab) turns off the display after a while yet, but the phone turns off completely opens up the phone to come out after the apple logo .. What is the reason I'd appreciate if you help how to fix it ...pleasa help me

Doing those doesn't turn off your phone?
As stated hold down the top button only until you see the red slider to power off your phone.
If that doesn't work then take it to Apple and see what they say.

My iphone has locked up displaying a received text message and also a radio station app. I can't get it to restart by pushing and holding the on/off button. Any suggestions to try?

My iphone has locked up displaying a received text message and an app playing a radio station. I can't restart the phone by holding down the on/off button. Any suggestions to try?

Hold the home button and the Sleep/Wake button ignoring the slide to power off message until the phone turns off then you can repower it by pressing and holding the sleep/wake button for a few seconds until the apple logo appears.

Is there a way to view video via the display AND TV out at the same time?

Is there a way to display the video output for supported apps on the display as well as through the TV out at the same time? To explain my setup briefly, I'd like to have the front seat passenger in my vehicle be able to hold the iPad and watch video while the A/V cable runs through the car system and displays on the ceiling mounted TV for the back passengers.
As of right now, it seems as though it will only allow for one display at a time, and in this case, only showing video through the TV out. I don't know if the iPad has the processing power to mirror outputs to the display and the TV out at the same time, though I imagine that it should.
So, does anyone have any ideas on how to make this possible, if it's possible at all?
Thanks in advance.

If you'd emailed Steve Jobs with this question, here is what his response would have been had he blessed you with a reply:
No.

Macbook pro 13 late 2011 turns on but no display and light

Hi i have got macbook pro 13" late 2011 which turns on and i can hear the chime but there is no display and ligh in the screen its completely blank. Anyone had this problem and how did u solve this ?

Have you tried booting into the Recovery HD and running Disk Utility and checking to see if the HD needs repairs?
Restart holding Command + r and at the recovery screen select Disk Utility. Then select Macintosh HD and click on 'repair disk'. If anything gets altered click on repair disk again until you get a clean pass. Restart as normal from the Apple menu. More info here about the Recovery HD:
http://support.apple.com/kb/HT4718

Is it possible the current Mac Mini 2.7 Ghz i7 with two full-resolution displays and Thunderbolt operate?

Hello,
Is it possible the current Mac Mini 2.7 Ghz i7 with two full-resolution displays and Thunderbolt operate?
Thanxs for your answers.
Gerald

On Second thoughts...
I don't really know how well Logic Express 7 performs on the Mac Mini because I have not yet had the chance to experience the two together. Don't let that put you off the idea though! From my understanding of the system requirements printed on the Logic Express homepage, it states that a G4 or faster system is required, however Apple personally recommend a Dual G4 or G5 is recommended alongside a minimum of 512MB of Ram. This Does mean that Logic Express will run on the Mac Mini but you will most probably find it lags when moving samples in real time and rendering them onto your hard drive. If you really want to enjoy making "serious" music on the Mac then you really need to be looking at the iMac G5 or the iMac Core Duo (Intel) purely for your tempers sake. As for an Intel Mac Mini, there is no indication as to when we will be seeing one on the market and therefore you may find yourself on the fence between keeping your fixed budget and holding on a little or jumping in and getting on the right road to a digital musical life - mac style.
Maybe this will inspire your decision:
http://www.engadget.com/2005/02/08/how-to-turn-your-mac-mini-into-a-low-cost-rec ording-studio/
Hope this helps
-Pos

Out of Frequency Problem with Apple Multiple Scan 720 Display and Mac mini

If a resolution with a horizontal and/or vertical frequency not compatible with your display, in this case an Apple Multiple Scan 720 Display, is selected in the Display preference pane of the Mac OS X 10.4.10 system running on a Mac mini (Early '06), you will recieve a message on your screen about being "out of frequency" and the power management feature will shut down and restart your display repeatedly. The following solution should restore your display to proper function. It may apply to other displays and Macintoshes running Mac OS X, but it has only been tested specially on this setup.
1. Shut down the Mac mini with the power button (press and hold for 5 seconds)
2. Start the computer up with the Mac mini Mac OS X Install Disc 1 (press the power button, insert the disc, hold the C key down until the progress bar starts up)
3. Click on the language, then select Utilities > Terminal...
4. Type "cd /" and return
5. Type "cd Volumes" and return
6. Type "cd your hard drive name" and return (you need to enclose the hard drive name in double quotes if more than one word)
7. Type "cd Library" and return
8. Type "cd Preferences" and return
9. Type "rm com.apple.windowserver.plist" and return
10. Type "exit" and return
11. Quit Terminal
12. Select Utilities > Startup Disc...
13. Select the OS on the hard drive and click on Restart button, holding down the Shift key until the progress bar starts.
14. Log in to the account that had the display problem in Safe Boot mode
15. In System Preferences select Display, select a resolution with the appropriate frequency, 60 Hz should be fine, then close System Preferences
16. Restart the computer, log in to the account normally, and the display should be functioning properly.
DO NOT SELECT AN INAPPROPRIATE RESOLUTION/FREQUENCY FOR YOUR DISPLAY IN THE DISPLAY PREFERENCE PANE! BE AFRAID, BE VERY AFRAID!
Mac mini (Early '06) Mac OS X (10.4.10) Apple Multiple Scan 720 Display
Mac mini (Early '06) Mac OS X (10.4.10) Apple Multiple Scan 720 Display

Just a correction and an elaboration:
It should be Startup Disk... with a k, not a c.
Both the resolution and the frequency must be appropriate for your display to work properly. Check your documentation or the manual information available on your display for the appropriate resolutions/frequencies. Evidently the Apple Multiple Scan 720 Display is considered so old that no allowance was made for it in the Display preference pane of Mac OS X 10.4.10.
Mac mini (Early '06) Mac OS X (10.4.10)

27" display and late '09 MBP 13" - Display software update **doesn't work**

Hello All,
My shiny new 27" LED cinema display arrived today. The display is stunning, but when I downloaded and installed the "LED Cinema Display Software Update 1.0" (http://support.apple.com/kb/DL1107) on my mid-'09 MBP 13" it doesn't work!!
The installation completes successfully, but after rebooting and checking system preferences, I don't get the brightness slider etc nor the option to use the built-in speakers in the display.
Please advise if you have any advice or thoughts on the matter.
Many thanks,
Rob

Apple got hold of me and we went through some trouble-shooting steps. Turns out that the USB connector, although fully plugged in, was somehow not seated correctly and was thus not recognizing the display and speaker etc.
Happily resolved!

Siri window does not display and app was destroyed with latest 6.1 update

This happened right after the last update to 6.1. Press the button and hold it. You get a beep but no SIRI window. Otherwise it will do as you tell it to.
There are numerous other bugs. Go into Purchased apps. Cannot select an app on the second row left, second one down from the top. eith the one above it displays or the one below it.
The update also destroyed an expense tracking app, Pocket expense which had a substantial amount of data in it. Press on the app icon and it flasehes and does not run.

Have you tried restarting or resetting your iPad?
Restart: Press On/Off button until the Slide to Power Off slider appears, select Slide to Power Off and, after the iPad shuts down, then press the On/Off button until the Apple logo appears.
Reset: Press the Home and On/Off buttons at the same time and hold them until the Apple logo appears (about 10 seconds). Ignore the "Slide to power off"
If neither of these work you may have to restore your ipad via iTunes on your computer.

Our mac pro went to a very faint display and we can't fix it.

Our week old mac book pro suddenly has a very faint display, almost all black and we can't fix it. We've re-started etc.

I assume you have tried the "obvious" stuff, like using the brightness buttons (F1 = dimmer, F2 = brighter) or turning up brightness in system preferences>displays. I'm sure you tried all that, but I just had to say it just in case. Anyway, you may want to try reseting your PMU...
PMU stands for Power Management Unit and it is a chip that controls the backlighting of your display (among other things). To reset your PMU do the following:
1. If the computer is on, turn it off.
2. Disconnect the AC Adapter and remove the computer's battery.
3. Press and hold down the power button for 5 seconds and then release the button.
4. Reconnect the battery and AC Adapter.
5. Press the Power button to restart the computer.
Those are the official apple instructions, but I suggest in step 3 you hold the power button down for 10 seconds.
Here is a link that refers to reseting the PMU on a MacBook.
http://docs.info.apple.com/article.html?artnum=303319
good luck!

When I disconnect my MBP from my Thunderbolt display and reconnect, arrangement resets.

I have a MBP Retina and a 27" Thunderbolt display. When I disconnect from the Thunderbolt display and then reconnect, my arrangement is reset and I have to set it again. This has been happening for the last day.
I am on OS X 10.10.1 Yosemite and I just updated the Thunderbolt firmware yesterday.

Try:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Unsync/delete all music and resync
To delete all music go to Settings>General>Usage>Storage>Manage Storage>Music>Tap edit in upper right and then tap the minus sign by All Music
- Reset all settings
Go to Settings > General > Reset and tap Reset All Settings.
All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
- Restore from backup. See:
iOS: Back up and restore your iOS device with iCloud or iTunes
- Restore to factory settings/new iOS device.
However, there seems to be a bug in iOS 8 or iTunes 12.1.1 that cause this problem and I have not seen a solution

Not responding before press and hold any key

I have to press and hold any key on my blackberry 8520 before it response. This started after downloading some app from the appworld. If I leave the phone for one minute idle and gets a call, I have to press and hold the send key for about 30 seconds before I can pick the call. I hv perfomed the security wipe for more than 3 times and still the problem exist. Need some help pls

Hi and Welcome to the Community!
It sounds like those apps may have corrupted the OS, and therefore an OS reload may be required. The simplest way is to, on a PC (you cannot do this on MAC):
1) Make sure you have a current and complete backup of your BB...you can find complete instructions via the link in my auto-sig below.
2) Uninstall, from your PC, any BB OS packages
3) Make sure you have the BB Desktop Software already installed
http://us.blackberry.com/software/desktop.html
4) Download and install, to your PC, the BB OS package you desire:
http://us.blackberry.com/support/downloads/download_sites.jsp
It is sorted first by carrier -- so if all you want are the OS levels your carrier supports, your search will be quick. However, some carriers are much slower than others to release updates. To truly seek out the most up-to-date OS package for your BB, you must dig through and find all carriers that support your specific model BB, and then compare the OS levels that they support.
5) Delete, on your PC, all copies of VENDOR.XML...there will be at least one, and perhaps 2, and they will be located in or similarly to (it changes based on your Windows version) these folders:
C:\Program Files (x86)\Common Files\Research In Motion\AppLoader
C:\Users\(your Windows UserName)\AppData\Roaming\Research In Motion\BlackBerry\Loader XML
6a) For changing your installed BB OS level (upgrade or downgrade), you can launch the Desktop Software and connect your BB...the software should offer you the OS package you installed to your PC.
6b) Or, for reloading your currently installed BB OS level as well as for changing it, bypass the Desktop Software and use LOADER.EXE directly, by proceeding to step 2 in this process:
http://supportforums.blackberry.com/t5/BlackBerry-Device-Software/How-To-Reload-Your-Operating-Syste...
Note that while written for "reload" and the Storm, it can be used to upgrade, downgrade, or reload any BB device model -- it all depends on the OS package you download and install to your PC.
If, during the processes of 6a or 6b, your BB presents a "507" error, simply unplug the USB cord from the BB and re-insert it...don't do anything else...this should allow the install to continue.
You may also want to investigate the use of BBSAK (bbsak.org) to perform the wipe it is capable of.
You may also want to try the "Bare Bones OS Reload Procedure" to attempt to narrow down the precise causal item:
Load your OS "bare bones"...if anything is optional, do not install it.
If the behavior presents immediately, then try a different OS with step 1
If the behavior does not immediately present, then run for as long as it takes for you to be sure that the behavior will not present.
Add one thing -- no matter how tempting, just one.
If the behavior does not present immediately, then again run for long enough to be sure it will not have the same problem
Repeat steps 4 and 5 until all things are loaded or the behavior presents
When the behavior presents, you know the culprit...the last thing you loaded.
If the behavior does not re-present, then you know that either step 1 or 2 cured it.
If the behavior presents no matter what, then you likely have a hardware level issue for which no amount of OS or software can cure.
You may also need the use of these tricks:
KB10144 How to force the detection of the BlackBerry smartphone using Application Loader
KB27956 How to recover a BlackBerry smartphone from any state
http://crackberry.com/blackberry-101-lecture-12-how-reload-operating-system-nuked-blackberry
If you are on MAC, you are limited to only your carriers sanctioned OS packages...but can still use any levels that they currently sanction. See this procedure:
KB19915How to perform a clean reload of BlackBerry smartphone application software using BlackBerry Desktop Software
Good luck and let us know!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

MuVo TX FM display and power prob

hello to all! good evening...i've been the owner of a creative MuVo TX FM for a little over a year now and im extremely satisfied with it. it was extremely reliable and handy and was a worthy competitor against the shuffle...it never gave me any problems at all and i was quite happy with it...
recently, it started acting up and anytime i press and hold the power button, the LCD display just flashes and nothing happens...the light goes on and keeps flashing at sec intervals!!! thats all that happens...i have to keep trying and hold it and after repeated attempts and if the player thinks im worth it, it goes on!! its really irritating and ANY help at all will be really appreciated!! thanks for your time! hope for a reply soon!

hello!!
thanks a lot! its working just fine now!!!
cheers!

Cannot get my LG g2 to display and need assistance

charged my phone over night as usual. no display. when power on I have black (blank screen. phone does a 2 buzz sequence. when call cell from home phone msg says not in service.

@okjoy,
VZW to the rescue! Let's get your phone acting right.
Has there been any physical or liquid damage? Press and hold the Power button (located on the back) until the device powers off (approximately 5 seconds) then release.
Keep me posted!
JohnB_VZW
Follow us on Twitter @VZWSupport

Display and hold

Similar Messages

Maybe you are looking for