Display release button???

Hi there,
I bought an Ibook G4 3 months ago and I noticed that sometimes the display release button (button to press to open the ibook open) blocks inside... I then need to press at the extreme left or right for it to open. Is this a real problem with the display release button or is it normal(wear n tear)? Can I send it to the service center for warranty repair? It only happens sometimes.
Thanks

The problem with something that "only happens sometimes" is that if you send it in, Apple may not be able to replicate the problem. If they can't, it's a wasted trip.
If you haven't already bought AppleCare, I would recommend that you do so in case the problem becomes worse. AppleCare lets you call in on a problem like this for a full three years and if it needs fixed in those three years (not just for this, but for any problem — barring accidental damage or abuse), they will fix it.
http://discussions.apple.com/thread.jspa?messageID=610758

Similar Messages

Opening Display with the "Display Release Button"

Hallo
I have some real problems with my display of the MBP 17. First the not homogen backlight of the LCD, already discussed in different threads in this forum.
Another frustrating problem is opening the display. When you push the Button, it opens for about 1-2 mm. and then it is different to open it normal. My old PowerBook G4 17 and also an MBP 15" at my dealers place open normal for about 1-1.5cm.
Are their more users of the MBP 17" with the same problem. I found antoher machine around here in switzerland with the same problem (but not many MBP17 are arrived here)
I think this first release serie has really some serious bugs in the hardware design and need to be replaced in a secound or third revision!

Probably a setting. Look at the manual.
iPhone User Guide (For iOS 4.2 and 4.3 Software)

Display release button problems?

Im buying a used Powerbook G4 1.5ghz 17" from a friend and the button on the front of the powerbook that you press to release the display and make it come up is having problems, i.e.-I must hold the back of the laptop while I firmly press it with my fingernail to release/unlock the screen. Can anyone tell me if this is a bad problem or is it smoething easyily fixed? I dont want to spend money on a paperweight?! Thanks ahead of time for the help, its greatly appreciated!

When the display is being closed, hooks in the top of the display housing should be
magnetically pulled down to the latch. When the latch button is pushed, the hook should
release and retract into the display housing.
1. Verify hook operation by using a small low-power magnet to exercise the latch
mechanism. Make sure hooks are not bent.
2. If the hook does not operate properly, replace the display panel assembly.
3. If the latch or latch button does not operate properly, replace the top case assembly.

Display Release Button stuck on open

Cannot latch the display closed. First time this ever happened. Anyone got an easy fix?

hey man i know it's been a while since you had this problem, but as you can see from my post i had the same problem. what i did was take the blade of an exacto knife and clean out the area. you have to clean VERY THOROUGHLI!! this means running it along the bottom, gettin in as far as you can, and even trying to pull the mechanism back with the blade. good luck man if you haven't fixed it already.

SRM 7.0 - Release button

Hi Gurus,
I need to check out the Action that stands behind the Release button on the contract header, but can't figure it out.
the problem is that behind the button i find a generic webdynpro (FPM_OIF_COMPONENT) without highlighting any real button / action.
can anybody help?
thanks
Edited by: Michele Camuri on Jul 19, 2009 10:49 PM

Hi Ganesh,
In Employee Self Service tab we have POWL table view where list of Shopping Cart number are available,right?
In this screen we have "Shop"/"Display"/"Edit"/"Print Preview" buttons.
My issue is when i click on "Display" or "Edit" button it's opening the Portal Home Page, i.e. the First page we are getting after login to Portal.
In the Manager tab we are also getting the same issue..when we are clicking on any of Work items it is redirecting to Home Page..also "Resubmit" and "Forward Button" is a doing the same thing...
hope you'll be now able to understand the issue....
Experts please help...badly stuck in this issue..
Regards,
Sambaran Chakraborty

How can I disable display/Change Button on transaction code VL03N

Dear Guru,
I found problem about transaction code vl03n because I define authorize for a user that can only display delivery document by transaction code VL03N. But this transaction have display/change button that when user click this button they can change delivery document. Please help me how can I solve this problem?
Best regard,
wipaporn

Wipaporn,
This should be done authorizations only. Although the button is displayed, is the user able to change and save the Delivery document?
Regards,
Ravi

How to display action buttons on iPad app?

Hi all,
I'm trying to display "action buttons" in my custom BO's TI in advanced list panes. For each of these table I created LayoutStackPanel where inside I have icon with defined event handler. In web UI version everything works fine. "Action button" appears and event handler is triggered on click.
When I open same TI on iPad, first of all Table is displayed as grid, not table, but I assume that is how iPad player generates that. But my created icon is not visible in specific row (I haven't allowed hover option as I thought iPad can't handle hover event), and even switching TI into edit mode it's not appearing and event handler isn't triggered.
I wonder if there is around some detailed guide, best practice doc which covers how we can design our screens for iPads.
Thanks,
Uldis

Hello Uldis,
Please try to follow these steps to create it from scratch. It guides you on how to create a Delete button, so you can use is as a reference for futher action buttons:
1. Drag and Drop ‘LayoutStackPanel’ from ToolBox to List Column.
2. Right Click on the column and Select Model ‘LayoutStackPanel’. Add an icon over there.
3. Set the property ‘Visible on Hover’ of Layout Control to True.
4. Create an action on your BO node called Delete<NodeName>. Generate the script file and add this snippet:
this.Delete();
5. Set the property ‘On Click’ in UI Designer.
Create EventHandler calling the BO action. The EventHandler and "Misc" name must contain "Remove" or "Delete" as prefix to identify as a deletion column. As sample you can check the "Account Team" facet of account Thing Inspector:
/BYD_COD/SalesOnDemand/Account/UI/COD_Account_TI.TI.uicomponent
Click on the "Items" collection as following figure shows:
Then set the Icon ‘OnClick' event to your delete event previously defined.
Let me know if that worked for you.
Best Regards,
Fernando Giroleti
Cloud Service Center AMEA

The new ribbon user interface in Win 8.1 should display appropriate buttons depending on the currently displayed folder within the explorer.exe window.

To begin with, in file-explorer (.\system32\explorer.exe) normally, the new ribbon user interface in Win 8.1 does indeed display appropriate buttons depending on the currently displayed folder within the explorer.exe window.
But when one re-parents the explorer window handle to any window handle other than 0000 (desktop's window handle), then the UIRibbon fails to do so.
You might ask 'Who does that ?' and I would say no-one usually, however I use BrightExplorer which
is a great little app that gives me a tabbed file-explorer experience.
Now, this app works fine since Windows 7, but with Windows 8 the file explorer introduced the new UIRibbon in its UI. It's that new UIRibbon that gets confused by what I think may be be caused by the re-parenting that BrightExplorer does
to pull a file explorer session into its tabbed control.
This phenomenon relates to Windows 8 + and is observed only by doing the following steps:
Download BrightExplorer from BrightNewWorlds.com by going here: BrightExplorer,
In the address bar go to This PC,
then go to any other folder and note that the UIRibbon is not keeping track of the changing folder selections.
Does anyone out there feel that they can do something about this, or have advise?
Kind regards,
Robert van der Meijden

To begin with, in file-explorer (.\system32\explorer.exe) normally, the new ribbon user interface in Win 8.1 does indeed display appropriate buttons depending on the currently displayed folder within the explorer.exe window.
But when one re-parents the explorer window handle to any window handle other than 0000 (desktop's window handle), then the UIRibbon fails to do so.
You might ask 'Who does that ?' and I would say no-one usually, however I use BrightExplorer which
is a great little app that gives me a tabbed file-explorer experience.
Now, this app works fine since Windows 7, but with Windows 8 the file explorer introduced the new UIRibbon in its UI. It's that new UIRibbon that gets confused by what I think may be be caused by the re-parenting that BrightExplorer does
to pull a file explorer session into its tabbed control.
This phenomenon relates to Windows 8 + and is observed only by doing the following steps:
Download BrightExplorer from BrightNewWorlds.com by going here: BrightExplorer,
In the address bar go to This PC,
then go to any other folder and note that the UIRibbon is not keeping track of the changing folder selections.
Does anyone out there feel that they can do something about this, or have advise?
Kind regards,
Robert van der Meijden

"Display Form" button not visible in UWL preview

Hi Friends,
We are implementing Travel module. The standard Workflow WS20000050 has a single level of approval. However, we wanted 2 level approval and so accordingly this was implemened.
Now we want a 3rd level of decision step to be approved by the traveldesk on recept of tickets.
Even the pdf form, which contains the travel details, needs to be visible. In the standard task TS20000118, the "Display Form" button is automatically visible in the UWL preview apart from the usual
"Approve" and "Reject" buttons.
However the content that needs to be shown to the traveldesk is different. To achieve this, i copied the standard task TS20000118 and changed only the task description. Rest everything including the parameters and binding remains same.
But for this task, the "Display Form" button is not visible.
1. Please advice on the possible reasons why this is happening ?
2. Is there any setting or any SPRO configuration wherin we need to
specify the tasks for whom the button needs to be displayed ?? or
Is it some portal side configuration ?
Thanks,
Shashank

Hi Vijay,
Goto:
Universal Worklist Content Configuration -> Click to Administrate Item Types and View Definitions
In the table under the "Current Configurations" tab, select the standard travel configuration provided by SAP -> "com.sap.pct.erp.mss.tra".
Here, search for the code of the task for which everything is working fine; in our case it was TS20000118. Copy this piece of code.
Now download the currently active XML configuration. In the saved XML file, search for the task code which is not working as expected. Replace this piece of code with the code copied in the above step. Save with a different name.
Upload this new configuration with HIgh priority.
Reregister the connector and clear the cache.
These steps solved my problem. Probably it should work for you too.
Regards,
Shashank

Credit Management: Use of release button in VKM2

3)what is the use of release button in VKM2. where does it releases?
Notes: If Credit Management is activated at Sales Order level and the credit block is removed through VKM1,VKM3 or VKM4, we can see the in VKM2 transaction code. But in VKM2 transaction code, we have release option .
What is the purpose of this options. Please assist me regarding the VKM2 transaction code.

The release button in VKM2 will have no affect on the document if it has already been released. I guess that if you release the document again the release date would be updated but nothing more.
I hope this helps.
Gerard

1D M4 how do I remove lens after broken lens release button

During a weding shoot the leans release button brok. How do i remove the leans?

You may need to call Canon.
The mounting ring on the lens has a tiny hole in it. The lens flange on the body has a tiny spring-loaded pin. When you mount a lens (red dot on lens lining up with red dot on body) that pin is pressed into the mounting flange until you rotate the lens far enough that the hole aligns with the pin and the pin locks into the hole. The sole purpose of the lens release button is to retract the locking pin.
When you press the button, it pushes against a metal tab which pulls the locking pin back. You may actually be able to see a tiny bit of that tab on the lens-facing side of the release button (through the tiny gap where the button fits into the body.) If you can press that metal tab back, it will release the pin.
The release mechanism is fairly simple... it seems as if it'd be hard to break. If the lens is trying to twist (somehow jammed) then it can make it so that the pin does NOT want to retract. If I attempt to rotate a lens which is locked on my camera body I can feel just a very tiny amount of play (which is normal.) If you're lens is jammed in and putting sideways pressure on the pin then it probably wont have any play at all - and that might make it hard to press the lens release.
Tim Campbell
5D II, 5D III, 60Da

MD04 - no release button available when clicking on purchase requisition

Hi experts,
A purchase requisition has been created that needs to be released.
This can be done via ME54 which works fine. Another possibility is via MD04 - click on the purchase req. number. A pop-up occurs and there should be a release-button (green flag).
My question:
What might be the problem, if the same user can release a PR by using ME54 but not by using MD04? He doesn't see the release button when he clicks on the PR-number within MD04.
I checked the user's roles and profiles which are the same as for another user where both ways work fine.
Release procedure without classification is used.
Thanks in advance and regards,
Ina

the user uses a different navigation profile.
assign the purchasing navigation profile in MD04 via menu Environment > navigation profile

CTS+ - Release button missing in CTS browser

Hello,
I am trying to set up CTS+ for our Portal environment. I can create a transport in the Portal, add objects and export.
But when I go to the CTS browser Web UI interface through the link beside the transport in the Portal, I don't have the release button there. I can see the transport, I see the object though.
When I use the CTS browser for the ABAP system (which is used as the central CTS system), I see the ABAP transports for this system and the button 'Release' is there. So it shouldn't be an authorization issue.
I have no idea what is missing.
Thanks,
Ingrid

Hi Ingrid,
which Link to the transport request are you using? Is it in the step where you can also choose the Export Method (Link 'Transport Requests') or after the export is done (Link <RequestNumber>)?
If the first is the case, then he behavior that you describe is the expected one. The assumtion is that in this step, you might want to check the objects that have already been attached to a request or create a new one.
If the second is the case, thean the behavior should be different.
As a first workaround, you could remove the parameter SELECT_REQUEST_MODE=X from the URL. This should bring back the Release-Button
If you used the link <RequestNumber>, after the export was finalized: was there another Browser Window showing the transport organizer web UI opened up before you clicked on the link? If yes, could you please close that window before clicking on the link? I am not saying that this is what you are expected to do, but I am just trying to find out, what happened.
If there was no other browser window opened up before, could you please let me know about the SP level of your portal and CTS system?
Kind regards
Karin

GOA Release button activation

Hello,
We don't want to keep the location(plant) information mandatory on Global Outline Agreement documents in order to release and distribute to the backend.
We are experiencing a situation where if we dont enter the location information on Item Detail -> Distribution tab, the release button stays inactive. However, if we hold the document and then release then there is no problem to approve and replicate the document on R/3.
Do you have a suggestion how to prevent this situation and be able to release without location information.
Thank you,

Unfortunately i didn't get an aswer yet and couldn't resolve the problem.
Did anyone of you experience such a problem?
Message was edited by:
Gaia K.

Release button flag not appearing in ML81N

Dear All
In my development system when I try to release service entry sheet through transaction ML81N in edit mode the release button flag is not appearing but in my quality system this release button flag is appearing.What could be the reason??
Pls help.
Regards
Satish Kumar

Hi,
its authorisation issue,Consult Basis Consultant & Check and compare roles assigned to user ID in both client.
Regards,
Biju K

Display release button???

Similar Messages

Maybe you are looking for