Display Sparkles and Ghosting

I have a 20" iMac G5 with ALS and the screen has just started playing up: I get sparkles (flashing white pixels) across the screen and windows leave noticeable ghosting once closed or moved. These seemed to be issues with the Rev. A iMac, and I purposefully waited for the Rev B hoping these problems would be solved. Now, the Rev A units are covered under the warranty extension program but, from looking at the webpage, my Mac's serial number falls outside the range.
Has anyone else experienced these issues with a later revision iMac?
The Mac is still under warranty. Will Apple fix the display even though it doesn't fit in the serial number range of recognized defective models?
Is there anything I can do about this or does the display need to be swapped out?

Thanks Eric for your answer and your optimism.
Apple Germany is notoriously incompetent for service (though admittedly that's a German problem not one specific to Apple): their CSR refused to even speak to me about this hardware issue unless I pay 49 Euro, because I'm out of my first 90 days of telephone support, and apparently they don't offer hardware repairs (even within the warranty period). I will have to search out an independent Authorized Service Provider on Monday.
Good to know that the problem is fixable though. Thanks for the feedback.

Similar Messages

  • IMac ghost display problems (and apple technicians weren't able to solve)

    Hi,
    So my problem here is quite weird. I tried researching the forum for something like this, but nothing really came close to whats happening to my iMac.
    I have an Intel-Based iMac, 24 inch screen.
    I bought it on 2008. Since late 2008/early 2009, i had these weird "letters" underneath all my pictures. I work with photography/video editing, so this was very annoying, yet i kept ignoring, since the rest was working fine.
    Then slowly the iMac ran slower, more sluggish-y. Like if all life was sucked out of it, sort of description.
    Then, 2 months ago, there was a total failure of the HD. I was lucky to be able to back up all, before it didnt let me even enter the computer. It would just think for hours.
    I brought it to the technical support near to my home, and i also told them about those weird "letters" on the left side of my screen. They said it was due to my hard disk, and i was, ok...since the hard disk had a failure.
    They did a check up, and yep, the hard disk was k.o, evidently. They replaced the hard disk, and told me all was fine.
    It did "seem" fine for the first couple days. No more running slow, no weird letters that would distort my pictures (for example, i could see my iTunes music list underneath a picture i was working on photoshop, or a video i was displaying!).
    After a couple of days...same story started again. The left side of the screen was flooded by all underneath (open windows, the desktop icons, the texts i had open on safari, basically anything would appear translucently underneath any image or video i would open). Then, flash player would crash every 3 videos, blank cd's would get automatically ejected so i couldnt burn any cd, computer would run slow etc... etc...
    So i cleaned up my computer, did a back up, erased all, and ready to bring it up to technical support again. And misteriously, all symptoms disappeared. So i explained to them what happened, and they said probably it was the graphic card.
    I thought finally my problem was solved.
    24 hrs later, i got an email that my computer was fixed. That it was only a hard disk "permits" issue, and they solved it.
    I have had the computer for 3 days, and the screen problem is starting again, and now the permits are perfectly fine in my computer, and nothing comes out as wrong in the diagnostics tool!!!!
    I didnt even work with the computer, but now i can see my itunes list through the safari window, as grey letters....kinda 3D, popping out. Its very weird. And i cant capture it because when i take a screen capture, it all appears fine.
    Left side of screen is the affected. And no, its not a condensation issue.
    Also, i can see some lines when i start up the computer. On the grey screen portion of the start up.
    I dont know what it can be anymore. I know this is a long post, but i had to explain all what happened to it.
    Any help would be great.
    Thanks

    You might want to clean up your profile. An iMac G5 will not run Mac OS X 10.6.4!
    My experience with things appearing on screen but not in a screen capture is that it is on the display itself and not involving the GPU.
    I think that you have image persistence, similar to CRT burn in. It is caused by having the same image appear in the same location over long periods of time, like a Safari window always in the same location, or an iTunes window, etc. The pixels get stuck showing that image.
    There are different little apps that folks have developed to get the pixels unstuck. Google LCD image persistence and you can find a number of them.
    Here is one suggestion;
    http://www.jscreenfix.com/
    Dah•veed

  • MBP & 23" Display "sparkles"

    Hi - when my MacBook Pro is connected to my 23" Cinema Display it creates "sparkles" throughout the display (green/blue) - I have read about this happening on the 30" but I haven't come across a solution yet - the 23" display works great with my Dual 1GHZ G4 Mirror Door (no sparkles) - I noticed it the first time I connected the MBP to the 23" monitor (I moved some cables around, anything magnetic etc - thinking this was the cause - the sparkles did not change) - Eventually the sparkles seemed to go away (or were not as annoying) - I have been traveling and just reconnected my MBP to the 23" and it was worse then ever (after about 5min it consumed my monitor) - I unplugged it - checked the cables again (plugged it into my old computer - no sparkles) and also "air dusted" the connectors - it is not as bad - but still very noticable - I would imagine its the MBP video card - (Radeon X1600)
    Does anyone have any thoughts?
    Thank you
    MacBook Pro 2GHz Core Duo   Mac OS X (10.4.8)  

    I would firstly try resetting PRAM and NVRAM…
    http://docs.info.apple.com/article.html?artnum=2238
    … and failing that, contact AppleCare. It's possible you have an issue with your GPU/VRAM.

  • Adobe reader xi i am running 2 display screens and when i have a file open and go to print the print page opens on my second screen.  How can I get adobe reader to just display on one screen?

    adobe reader xi i am running 2 display screens and when i have a file open and go to print the print page opens on my second screen.  How can I get adobe reader to just display on one screen?
    I want the capability of adobe reader to just run on one screen.

    I had the same problem.
    Try this.
    https://igppwiki.ucsd.edu/groups/publichelpwiki/wiki/a1538/Howto_Disable_Acrobat _as_the_Safari_PDF_Viewer.html

  • SharePoint 2010 Web Analytics showing user Display Name and Account Name from the same user

    Hi!
    Since July, 16th 2012 the Web Analytics Daily Unique Visitors reports started to show almost the double of visitors we used to have on our Web Application. Here are some of the data (I intentionally deleted the weekend data):
    10/7/2012 2.497
    11/7/2012 2.723
    12/7/2012 2.722
    13/7/2012 2.699
    16/7/2012 5.055
    17/7/2012 4.963
    18/7/2012 4.954
    19/7/2012 4.998
    20/7/2012 4.965
    23/7/2012 5.117
    24/7/2012 5.012
    25/7/2012 5.071
    As you may notice the data jumped from around 2.700 unique visitors to around 5.000 unique visitors. As the number of permissioned users remains constant it is pretty odd. I also checked the Number of Page Views report and see no change on its behavior.
    The number of page views remained constant.
    So I went to look the Top Visitors report and understand why the visitors number almost doubled. The analytics started to count the users Display Name and Account name as two different visitors with a different number of page views. Let me show you an example
    from yesterday (July, 25th) Top Visitors report:
    #     Visitor                  Page Views    %
    1    Cinthia XXXXXXXXXX    359        0,55%
    5    Giselle XXXXXXXXXX     143        0,22%
    7    Aline XXXXXXXXXX       138        0,21%
    15  nt\cmazevedo              111        0,17%
    60  nt\gbsantana                 69        0,11%
    73  nt\aglsiqueira                 65        0,10%
    "Cinthia" and the account "nt\cmazevedo" are the same person. The same is applied to "Giselle" / "nt\gbsantana" and "Aline" / "nt\aglsiqueira".
    As I stated this is an example from July, 25th. If I checked the same report from a period before July, 16th I can only see the users Display Name as "Visitors". No account name is displayed or counted as a different visitor.
    About the environment:
    We have two SharePoint 2010 farms: a "corporate" and a "enterprise". The corporate farm contains four web servers and a central administration servers with publishing services. The enterprise farm contains two servers running User Profile Services, Search
    Services and some others. Our main version is the SP1 with June/2011 Cumulative Update with a few more hotfixes applied.
    This behavior on analytics is affecting all web applications (we have more than 20) installed on this farm and my company Support team said that no change were made on SharePoint on the weekend the problem started.
    Does anyone have any tip about what is going on?
    Thanks in advance!

    Hi, Manas!
    First of all thanks for your interest on this issue but I don't think it is related to the User Profile or the Active Directory.
    I checked both records and there was no change on the Display Names. All the users have "full names" as display names (first + middle + last name) and not logins as SharePoint is displaying on this report.
    But I did a test yesterday and checked the results today confirming that just the access been made using a specific server are causing this. Explaining it better:
    I have four web servers on my farm named from P01 to P04. Then I created this test script:
    Step 1: Change local HOSTS file to point the web application on the server P01.
    Step 2: Access site "A"
    Step 3: Access site "B"
    Step 4: Close the browser.
    Step 1: Change local HOSTS file to point the web application on the server P02.
    Step 2: Access site "C"
    Step 3: Access site "D"
    Step 4: Close the browser.
    Step 1: Change local HOSTS file to point the web application on the server P03.
    Step 2: Access site "E"
    Step 3: Access site "F"
    Step 4: Close the browser.
    Step 1: Change local HOSTS file to point the web application on the server P04.
    Step 2: Access site "G"
    Step 3: Access site "H"
    Step 4: Close the browser.
    I asked three users to execute that script. The results: All access to the sites "C" and "D" were registered on Web Analytics with the user account name such as "nt\cmazevedo". All the other sites registered the user Display Name correctly such as "Cinthia
    XXXXXXXXXX".
    With this test we could isolate the problem just on the server P02. It doesn't occur on the others. Now my support team is trying to find any configuration difference between this server and the other three that could point for the root cause.
    I am also looking for some information regarding the service responsible for this task ("transform the account name into a display name") to understand why it doesn't work on one server and works on the others.
    Thanks!

  • I was recently sent a very large emoji message amd now when i try to acces messages it will not display mesagges and then will bring me back to the home page

    was recently sent a very large emoji message amd now when i try to acces messages it will not display mesagges and then will bring me back to the home page

    Quit the messages app and reset your phone.
    Go to the Home screen and double click the Home button. That will reveal the row of recently used apps at the bottom of the screen. Tap and hold on the app in question until it jiggles and displays a minus sign. Tap the minus sign to actually quit the app. Then tap anywhere on the screen above that bottom row to return the screen to normal. Then restart the app and see if it works normally. Then reset your device. Press and hold the Home and Sleep buttons simultaneously ignoring the red slider should one appear until the Apple logo appears. Let go of the buttons and let the device restart.
    After the phone restarts go into Messages and delete the thread containing the problem message.

  • HDMI, Mini Display Port and Mountain Lion

    Hello,
    After reading about numerous issues concerning the Mini Display Port and Mountain Lion, I'm trying to discuss it here with you all to see if there is any solution.
    I have a MacBook Pro (2009), and used it with my TV (HDMI cable + Mini display port adaptor) with Plex media center back when it was on OS X Lion. It was very convenient because as a portable computer, it could easily be set near the TV and allow the use of a remote to sit in the couch and stream media from the Time Capsule… without the help of any expansive box. Perfect setup I've had for over a year.
    The thing is, since I've upgraded to Mountain Lion, when I try to connect the MacBook Pro to the TV, the screen turns blue as if it was calculating the resolution of the monitor so… ok. Until it comes back, and nothing changed either on the MacBook Pro screen or on the TV.
    Harware side, I've tried with the computer open, closed, I've checked every port and connection on both computer, TV and adaptor.
    Software side, what I find really annoying in Mountain Lion is that they completely ditched every monitor setting as long as nothing is connected — and even if the Mini DP is connected… the Mac thinks it's not. I even tried to reset the PRAM. This is a nightmare.
    I've tried to do the same with my iMac (mid 2011), and it all worked properly. What I can't explain is why it works on my iMac and not on the MBP… as they have the same configuration !
    I don't know if Apple is outcasting old devices so people buy new Apple stuff or if they ditched the HDMI out on certain (old) devices on purpose so users replace it by the new airplay mirroring feature and buy the Apple TV. I won't, because let's say it's a total crap compared to other media center solutions. And I'm bored of Apple.
    Please, HELP NEEDED ! Has anyone had the same issue ? I bet you have ! Now how can we solve that ?
    Thank you for your time.

    EDIT : stopped working on iMac too… then update 10.8.2 fixed the issue. Now it works. Thanks Apple for temporarily removing some features ! It's just so ANNOYING.
    Hope you gonna stay with the few we have left on Mac and stop removing things randomly. Not event talking about the pro environment (designers, developpers, etc.) that is almost gone. 2 years and our macs will be tablets. Careful with the old clients… it's been almost 10 years I'm on a Mac and I've never been so unhappy.

  • Need a mini display port and audio to HDMI adapter for mid 2009 13" macbookpro

    Can some body recomend an adapter cable that plugs into the audio (mid 2009 MacBookPro 13") and mini display port and outputs to HDMI with audio and video all together for a TV?  I would rather not run a separate audio cable in addition to the HDMI cable.

    http://www.kanexlive.com/iadapt51 - 5.1-channel surround sound from sources that provide such a signal
    http://www.kanexlive.com/iadapt20 - 2-channel stereo sound

  • I have a PowerBook G4 with a non-functioning monitor.  It used to work with an external monitor, but I reinstalled the OS, which cleared the display preferences and now when I restart it won't detect the external monitor. How do I fix?

    I have a PowerBook G4 with a non-functioning monitor.  It used to work with an external monitor, but I reinstalled the OS, which cleared the display preferences and now when I restart it won't detect the external monitor. This means I can't use the computer anymore. How do I fix? I tried using the Command+F2 keyboard shortcut, but it doesnt' work.  It's possible that since I reinstalled the OS, it still needs to be set up, so there's only a welcome screen (but since I can't see it I'm not sure).

    There is no limit to the number of times you can re-install Office on the same computer.
    You can activate by telephone:
    The last paragraph is the relevant bit

  • I have 12 core with Quatro 4000 and 5770, I want to use dual monitor setup, monitors are NEC with Spectraview-II.  How do I connect?  4000 only has 1 Display Port and 1 DVI.  5770 has 2 of each, if I use both 5770 Display Ports, does the 4000 contribute?

    I just bought a 12 core with Quatro 4000 and 5770, I want to use dual monitor setup, monitors are NEC with Spectraview-II.  How do I connect?  4000 only has 1 Display Port and 1 DVI.  5770 has 2 of each, if I use both 5770 Display Ports, does the 4000 contribute any work at all?  I read where on a PC they would work together, but on a MAC they do not.
    I read that Display Port has higher band width than DVI, NEC monitors for best performance they recommend using DIsplay Port.
    When I was setting this up I looked at a Nvidia Quadro 4000, unfortunately it was for PC, it had 2 Display Ports, in the Mac version they reduce it to one.  I did not think there could be a difference.
    Mainly want to use it for CS6 and LR4.
    How to proceed??? 
    I do not want to use the Quadro 4000 for both, that would not optimize both monitors, one DP and 1 DVI.  Using just the 5770 would work but I do not think the 4000 would be doing anything, and the 5770 has been replaced by the 5870.more bandwidth.
    Any ideas, I am a Mac newbie, have not ever tried a Mac Pro, just bought off ebay and now I have these problems.
    As a last resort I could sell both and get a 5870.  That would work, I'm sure of that, it's just that I wanted the better graphics card.
    Thanks,
    Bill

    The Hatter,
    I am a novice at Mac so I read all I can.  From what I understand the NEC monitors I bought require Display Port for their maximum performance.  The GTX 680 only has DVI outputs.  Difference from what I understand is larger bandwidth with the DP.
    You said I have the 4000 for CUDA.  I am not all that familiar with CUDA and when I do read about it I do not understand it. 
    A concern I have is, that if I connect the 2 high end NEC monitors via the 5770, using it's 2 Display Ports I would have nothing connected to the 4000.  Is the 4000 doing anything with nothing connected?  I read where in a PC system the 2 cards would interact but in a Mac system they do not.
    Bottom line, as I see it, the 4000 will not be useful at all to me, since I want a dual monitor set-up.
    So far the 5870 seems the best choice, higher band width than the 5770, and it has 2 Display Ports to optimize the NEC monitors.
    I'm not sure how fine I am splitting hairs, nor do I know how important those hairs are.  I am just trying to set up a really fast reliable system that will mainly be used for CS6 and LR4.  Those NEC monitors are supposed to be top notch.

  • HI, I am trying to connect my macbook pro,  18 months old, to a projector using the mini display port and a cable/connector to a VGA port on the back of the projector.  It all fits but the there is nothing happening? no mirroring option. Any ideas?

    HI, I am trying to connect my macbook pro,  18 months old, to a projector using the mini display port and a cable/connector to a VGA port on the back of the projector.  It all fits but the there is nothing happening? no mirroring option. Any ideas appreciated.  Many thanks

    to get to the Detect Displays button you have to hold down the Option key and the button appears.
    SeanfromFulham wrote:
    Many thanks, however I don't seem to have any relevant options under displays.

  • Display value and description of one field in alv grid

    Hi Folks,
       I want to display value and description of one field as one column in alv grid.
    for example iam having Xfield = 01,02,03.
    and 01 iam having text value as xxx,
    01 xxx
    02 yyy
    03 zzz
    Im report display the values are displaying as 01,02,03..
    but i want to display it as 01 xxx,02 yyy, 03 zzz.
    Please do needful.
    Thx.

    Hi, swetha
    You can do this with "concatenate".
    example:
    In you code check where you final internal table is getting filled up before that do this concatenate and then append it.
    data t_text type string.
    t_text = textfield
    CONCATENATE 'Xfield'
                     t_text
                      INTO wa_workarea SEPARATED BY space.
    cheers,
    Bhavana

  • ALV report display online and generate in spool

    Dear expert,
    I have created an ALV report. I want to run this report online. After executed, the report is displayed. After display this report, I also want to generate the output report in the spool. Is there any way to do this? Thank you.
    I have tried to use submit...to SAP Spool. in this way, it will generate the spool, but it will not display the report online. I want it both display online and generate a spool.

    well forget yout the new-page print on thingie, since you use ALV.
    if you had a write list this trick would be cool since you just could do following:
    Do 2 times.
      if sy-index GT 1.
        new page print on.
      endif.
      loop at itab into wa.
        write stuff....
      endloop.
      if sy-index GT 1.
        new page print off.
      endif.
    enddo.
    /edit arrrgh forgot to write further...
    with your ALV you could process a write list as well after displaying but you will have layout differences between your display and your spool then and i dont think that this is what you want/need.
    you could however after display process your programm a second time, in background task and give it a printer where to print to. Since ALV wont get executed in background task you will get a spool instead.
    Edited by: Florian Kemmer on Sep 15, 2010 2:40 PM

  • Itunes artwork display issue and a fix for  'unknown error occured (-50)'

    Too bad they dont have stickies. This would be a great one.
    This is a thorough fix for art work and the -50 error.
    If you see artwork in itunes, first verify that the artwork is in the mp3 tag using a program like "tag and rename" http://www.softdepia.com/tagrename_download1291.html
    If the artwork shows up in tag and rename, then you added it correctly.
    If the artwork isn't displaying on ipod, delete the song and retransfer to the ipod. Next make sure the "view artwork" check box is checked. To do this connect your iPod to iTunes and there will be a checkbox that should be checked to see if you want artwork to show up on your iPod.
    If you get this message -
    The ipod cannot be updated. An unknown error occured (-50).
    And have no artwork at all in you IPOD , dont fret. I am getting there..
    NO you DO NOT NEED to FORMAT YOUR IPOD YET as commonly posted. I have tested and retested the following fix-
    Eject IPOD. Kill ITUNES.
    Backup the following files
    iTunes Library.itl
    iTunes Music Library.xml
    & anything in the Previous Itunes library folder
    and delete them. More info on these at http://docs.info.apple.com/article.html?artnum=93732
    Dont worry, its much easier to recreate the database than to wipe your IPOD.
    Next Start up ITUNES. Plug in IPOD. You now should have a empty database.
    At this time, uncheck copy ARTWORK to IPOD, and when it's done deleting artwork, CHECK Copy ARTWORK to IPOD.
    It now should sucessfully display ARTWORK and not get the -50 error!!
    Now, goto you ITUNES Music folder and drag to the library and it will add you music back in, including your PODCASTS.
    All you need to do is click the RESUBSCRIBE button and you are back in business!
    IF this fails, which i cant DUPLICATE anymore, try this
    http://docs.info.apple.com/article.html?artnum=300248
    Its the DREADED IPOD FORMAT article.
    But you probably wont need it if you follow all these steps.
    Post back if this doesnt work and if it does, give me some credit;)

    Just as an fyi, to shorten this procedure instead of deleting the files i found out you and open the .itl files and delete all the lines in it so its an empty file.
    Then open itunes, and it will rebuild the database with the files from the .xml file.
    This saves you from having to rescan the songs..

  • My MacBook Pro can't find the display brand and resolution

    Hello everybody,
    I have a MacBook Pro "Core i7" 2.7 13" Early 2011.
    I use and external display Philips 220C1SW
    Recently my mac won't recognize the Philips brand anymore and use instead a generic display resolution, which is wrong.
    Does anybody had the same issue?
    Looking forward your answers
    Mat

    Hello le-mat
    Check out the article below for resolving issues when connecting to an external display. I would start with resetting the NVRAM and SMC as they will resolve most display resolution and power issues.
    Apple computers: Troubleshooting issues with video on internal or external displays
    http://support.apple.com/kb/HT1573
    Regards,
    -Norm G.

Maybe you are looking for