Display very faint after resetting

Nano display very dim, can only see when at a certain angle...

Beth,
Have you check the brightness settings for your iPod? If not, head to Settings and double check it is not set to a lower value.
If that isn't the case, it could very well be a hardware issue, meaning your iPod will need to be serviced.
B-rock

Similar Messages

My itunes continues to play very faintly after I quit the program, what could cause this?

My itunes continues to play very faintly after I quit the program. I actually though I was going crazy but it does continue to play after the program has been shut down. Very, very low volume though. I can't pause it or turn it up or down. I do us imatch. Please Help!!!!

Do you have backups of all the data on the startup drive? If not, do nothing else until you've backed up that data, if you still can.

External Display resolution problem after resetting PRAM

Gello, I've got Fujitsu-Siemens P19-2 monitor hooked up to my MbookPro and after resetting PRAM the correct display resolution disappeared from the "Displays" menu in System PReferences.
So did the refresh rate option...
What do I do?
I really need to change the refresh rate and the resolution, but the refresh rate button is grey and unclickable, and the resolution simply isn't there (I need 1280x1024).
REsetting PRAM and SMC didn't help.

After a couple of resets everything went back to normal

Satellite C50-A-19T - display very faint

Hi I have a Toshiba Satellite C50-A-19T running windows 8 and lately the display is almost non-existent.
When I start the machine up, I can just about see the Toshiba Logo and that's about it - even it's hard to see.
What I have tried:
1) External Monitor - External display works fine (connected via VGA).
2) I've tried the Fn/F4 button to chang which display, tried a few settings and still nothing on Laptop Screen
3) I've obviously checked the brightness, it's almost max.
4) I've removed battery and power, left laptop off for a while, then tried powering back up with battery still out - nothing different.
5) I've googled like mad and tried removing battery & power, holding power button down for 60+ seconds, done this 5-10 times in all, still nothing when I power it back on
6) I've replaced the screen with one from another similar toshiba that I know is working - it acts exactly the same.
Is there anything else I'm missing here?
The laptop is working like a dream when plugged into an external monitor.....and I've removed and reloaded all display drivers, reset CMOS, etc.
I'm baffled now and this is for one of the kids for homeworks, so my ears are getting sore !!
HELP PLS !!

> 1) External Monitor - External display works fine (connected via VGA)
This is most important info which you have provided in your message.
In case the external monitor is OK, the GPU/motherboard should be also OK.
From my point of few the display panel (backlight) is faulty.
The display backlight does not seem to work properly.
You said that you have replaced the display well, is it compatible display panel?

L192W display very blurry after a few hours of operations

I have a J115 with a L192W , GeForc6100 on board card.
I noticed recently that after a few hours of usage, the L192 screen becomes blurry where every icons, windows or text has a shadow.
If I turn off the power for a few minutes, the problem goes away for a while and then came back.
Anyone has similar experience?
THanks
Solved!
Go to Solution.

after a couple of months tinkering with different solutions, i happened to see my neighbor on his way to the PC-recycle place to recycle his 12 yo CRT monitor from Viewsonic . The monitor came with a old (but thick) VGA cord.
I asked if I can try that before he recycles it. That was the solution.
My guess is that the stock VGA cable that came with the monitor was not shielded properly and it picked up some interferences from some other electrical sources or something.
Anyway hope that helps someone else in the future
PS: I ended up recycling the new stock L192 VGA cable and use the 12 year old Viewsonic VGA cable instead.

Help - iTunes display very weird after upgrade

Just upgraded my iMac to iTunes 7.0.2 and MacOS 10.4.8 using Software Update (foolishly accepting the "do you want to upgrade" prompt).
Once I restarted, the iTunes display is completely wacked - displaying weird combinations of letters & symbols instead of the playlist / track titles. For example, under "STORE" instead of displaying "iTunes Store" it displays "<symbol><symbol>F7<symbol><symbol><symbol>F5...". This affects every piece of text on the iTunes window except the headings. If I select an option on the left then it displays correctly - e.g. "iTunes Store". If I select any genres, tracks, etc then they do not change.
The music all plays fine and if I look at the library from another Mac (also using 7.0.2 and MacOS 10.4.8) then it all looks normal.
In addition, the List view in Finder is also weird, with the List view showing all numbers (& the occasional letter) in the file / folder names or details in bold.
This only seems to affect the main account - i.e. the one that owns the library. iTunes & Finder both look fine in other accounts on the same iMac.
I've tried deleting any preference (.plist) files that were recently changed. This does not cure the problem.
I'm stumped - can anyone help with any suggestions? Thanks in advance.
R.

Screenshots of the affected iTunes & Finder windows at these URLs:
http://www.pondlife.fastmail.co.uk/public/iTunes%20screenshot
http://www.pondlife.fastmail.co.uk/public/Finder%20screenshot

Our mac pro went to a very faint display and we can't fix it.

Our week old mac book pro suddenly has a very faint display, almost all black and we can't fix it. We've re-started etc.

I assume you have tried the "obvious" stuff, like using the brightness buttons (F1 = dimmer, F2 = brighter) or turning up brightness in system preferences>displays. I'm sure you tried all that, but I just had to say it just in case. Anyway, you may want to try reseting your PMU...
PMU stands for Power Management Unit and it is a chip that controls the backlighting of your display (among other things). To reset your PMU do the following:
1. If the computer is on, turn it off.
2. Disconnect the AC Adapter and remove the computer's battery.
3. Press and hold down the power button for 5 seconds and then release the button.
4. Reconnect the battery and AC Adapter.
5. Press the Power button to restart the computer.
Those are the official apple instructions, but I suggest in step 3 you hold the power button down for 10 seconds.
Here is a link that refers to reseting the PMU on a MacBook.
http://docs.info.apple.com/article.html?artnum=303319
good luck!

Hello . I hope to get a solution to my problem: ( I bought a laptop Mac Pro, a user But the seller was not the Secretary Laptop after arriving I've worked for almost an hour When connected to electricity Nour appears very faint, I do not see it quickly ht

Hello
. I hope to get a solution to my problem: (
I bought a laptop Mac Pro, a user
But the seller was not the Secretary :" ( !!
Laptop after arriving I've worked for almost an hour
* When connected to electricity
Nour appears very faint, I do not see it quickly
http://www.3rabart.com/up/download.php?img=38472
When separated from the energy, light shows intermittently and then disappears fast
http://www.3rabart.com/up/download.php?img=38473
I need urgent help please.
Thank you

Please ، How Email for a company ? I want to communicate with them about my problem "(

Hey, i have very strange prob with my iphone 5(latest version/updated), after resetting it, so it doesn't connect to my laptop, even it doesn't charge too. it does charge from wall charger i try all the possible methods but still i am facing the prob

Hey, i have very strange prob with my iphone 5(latest version/updated), after resetting it, so it doesn't connect to my laptop, even it doesn't charge too. it does charge from wall charger i try all the possible methods but still i am facing the prob any fix/solution for it.. Helppppp!!!!!!!!!!!!!!!!!!!!!!!! As soon as possible, it will be gratefulness,
Thnksssssss....

So you are saying that you followed all of the steps in the support document for problems with connection, including removing and reinstalling iTunes? You do not say what you have tried, so it is hard to make recommendations. If this is the case, then you have tried resolving driver issues? What if you go to Device Manager and look for the iPhone. You should be able to click on it and see about drivers. You can update/reinstall the device driver.

My iPod Nano 5th Generation no longer shows the display properly, only very faintly in the background. It is playing but as i can't see anything I cannot chose or control what is on !!!!. Can anyone help please ??

My iPod Nano has lost it's display although it shows very faintly in the background. Any suggestions please.

If the iPod is defective and not abused Apple will exchange it at no cost under your warranty.
Make an appointment at the Genius Bar of an Apple store.
Apple Retail Store - Genius Bar

After resetting ipad, unable to get to home screen. Only displays request to attach to Itunes, which I did. What next?

after resetting ipad and removing all programs, cannot get to home screen. Only get request to plug in to itumes,which I did, and it still goes back to that, and the apple logo.

The message means that you need to restore the iPad using iTunes. When you connect the iPad to your computer and launch iTunes, if you cannot see the iPad under the devices heading in the sidebar of iTunes, you wll have to restore using recovery mode. If you see the iPad under the devices heading, click on it and then click on the summary tab on the right and click on restore.
If that doesn't work, this is how to restore with recovery mode.
Disconnect the USB cable from the iPad, but leave the other end of the cable connected to your computer's USB port.
Turn off iPad: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for iPad to turn off.
If you cannot turn off iPad using the slider, press and hold the Sleep/Wake and Home buttons at the same time. When the iPad turns off, release the Sleep/Wake and Home buttons.
While pressing and holding the Home button, reconnect the USB cable to iPad. When you reconnect the USB cable, iPad should power on.
Continue holding the Home button until you see the "Connect to iTunes" screen. When this screen appears you can release the Home button.
If necessary, open iTunes. You should see the recovery mode alert that iTunes has detected an iPad in recovery mode.
Use iTunes to restore iPad.
If you are running iTunes 11 - and you can't see the sidebar - to to View>Show Sidebar from the iTunes menu at the top of the screen.

Display stays black after waking due to USB plug-in/out

hi,
i forget to unplug the external mouse at times after shutting thsi pup down. when i unplug it AFTER sleep it wakes up again...but the screen stays dark (eventhough at night i see a phantom image very very faintly)
inow i have the mouse coming in through a hub (kesington 4 port, no external power)..soemtimes i can unplug the mouse no prob from that...sometime it still makes the comp awake...with the darkened screen...
a solution often is closing, waiting for sleep, opening...
is there an easier way? (increase brightness? stay alert and unplug BEFORE closing?)
at times i have also had to reboot...
any info would be grrrrreat...thanks!
pedro

i have this exact same problem. it happens with anything usb i plug in, or at least it does it with my old usb mouse, printer, and external hard drive. its done it ever since i had the machine about 2 and a bit years ago. ive also noticed it does it with my bluetooth apple mouse. when the pb is asleep with the mains power connected, if i press the mouse button by accident with the display closed it wakes the computer and then if i open the display it sometimes has issues bringing the display back on.
I don't know what causes this whether its a fault or just a design flaw in hardware or software, but i've just learned to live with it and try and remember not to unplug anything usb whilst its asleep.
Your phantom image in the background is caused because the actual display is on and the lcd is making the image, but the backlight isn't turning on so unless ur in the right light you wont see the image, you'll get the same if you just turn the brightness down to the bottom on ur display. the image is still there just without the backlight.
hope that helps a little.

Every Since I Downloaded iOS5 O My IPhone My Volume Has Been Effected It's @ Max But Incoming Calls Come In @ A Minimum. When Taking A Call Thru Speaker Caller Sound Very Faint. Music Sounds Very Low Can Somebody Help Me ?

Every Since I Downloaded iOS5 O My IPhone My Volume Has Been Effected It's @ Max But Incoming Calls Come In @ A Minimum. When Taking A Call Thru Speaker Caller Sound Very Faint. Music Sounds Very Low Can Somebody Help Me ?

Hello ElleMalloy,
Sorry Im Just Responding Phone Has Been Downloading And Charging.
Well I Will Start Here,
I Tried Everything I Even Restarted My Settings Just So I Can See if That Would Work Because Someone Sujested It But What They Neglected To Say That Their Probrolem Was With A Ipad ? Anywho To Keep It Short I Went Online Logged A Complaint With Apple Made A Appointment With A Apple Store In My Area To Take The Phone There After Trying Everything (Resetting, changing setting etc..........) Nothin Worked Upon Taking The Phone To The Store They Swapped Out My Phone For A New One Volume On New Phone Is Perfect And I Only Had To Wait 40 Minutes

My screen is gray even after resetting. Then changes to white, is there any hope?

Just had my screen replaced, charged my i phone 4 and after unplugging the screen turned a faint gray. After resetting the i phone 4 several times the screen turns all white as if resetting and then back to gray. What should i do?

Hello JosepiSantos,
Thanks for using Apple Support Communities.l
I'm sorry to hear about the issues your iPhone is experiencing after getting the screen replaced. I'd like you to follow the troubleshooting below to try and help resolve the issue:
Display shows a white screen
Try turning iPhone off and then on again.
If the iPhone will not turn off, try to reset it.
If that doesn't work, try restoring the device.
Issue not resolved
My issue is still not resolved. What do I do next?
Contact Apple Support.
iPhone: Hardware troubleshooting
http://support.apple.com/kb/ts2802
Take care,
Alex H.

Temps rising again after resetting PRAM; SMC Version: 1.4f10

After running the firmware update, I was happy to see my MB running very coolly this morning (35 C.). After resetting my PRAM per AC's instructions for a display issue, I noticed my machine running in the high 50s/low 60s once again--same as before the firmware update.
Is this still in the normal range, or is there something else going on here?
Thanks in advance.

Thanks Eric. Actually, I'm not plugged into a display just yet. Just seemed strange the temps went up 20-30 degree C. Perhaps it was the time of day and duration of operation that accounts for the change.

Display very faint after resetting

Similar Messages

Maybe you are looking for