Distorted recording with QuickTime 7 using USB Audio CODEC

I am running Mac OS X Tiger 10.4.8 with all the latest update from Software Update which includes QuickTime 7.1.3.
I am using QuickTime Broadcaster to stream back to itself (loopback) and record to disk at the same time. The input audio device is set to USB Audio CODEC (the default driver that comes with Mac OS X Tiger, and I am using an Alesis MultiMix 16USB mixer on a PowerMac Dual Core G5). I am using MPEG-4 Audio compression (no Video) of 16-bit, 44.1kHz and 128kbps (stereo).
The problem is that sometimes I get recordings (ranging from 1.5 hours to 2.75hours long) with distortion. Here is a short 20-second audio clip with distortion-free audio for about 6 seconds and then distortion sets in:
http://www.netmedia.com.sg/files/SampleDistortion20s.mov
Whether it overlays on top of the original audio or replaces it, I cannot tell, but the transition is instant and smooth with no audible clicks or pops. The distortion can come in and go randomly. For example, I had one recording with distortion coming in at about 2 minutes plus and it remained until about 2hr10min when the distortion went away. Sometimes it didn't go away; other times it came in about an hour later. I also had once where the distortion last only for about 6 minutes somewhere in the middle of a 2.25 hours recording...all in all, it occurs at random. And I do get distortion-free recordings.
This problem also occurs on an iMac G5 with a Alesis MultiMix 12USB mixer, and in another Vara Software's Videocue PRO software which uses QuickTime for recording and playback. QuickTime 7.0.x and all versions of 7.1 also had this problem.
Because of this problem, I may need to use a convoluted method to stream and record to disk via QuickTime. By the way, I also tried streaming to another local subnet IP address just as a troubleshooting without success.

I too am having distortion problem (Sorry no solution here).
Using OS 10.4.8, QT7.1.3, & Adobe Premiere 6.5 on a G4.
After I down loaded QT 7.1.3, my problems started. Is this when your problems started too?
Audio is in "slow motion" sound when editing. On rare occations, it sounds correct for 10 sec or so but sync is out and eventually reverts to "slow motion" sound. Even more bazar, when viewing a clip in a thumbnail preview, it works fine. So I know the orginal is good.
My contention is QT is causing this. All I want is my previous version of QT back. I think this might fix your problem too. Unfortunately, there is no reinstall that I can find that takes QT 7.1.3 off and puts QT 7.1.1or2. The reinstall QT 7.0.3 which is on the Apple website will not restall.
Looking for a reintall that will take QT 7.1.3 off, help anyone?

Similar Messages

  • Distorted recording with QuickTime using USB Audio CODEC

    I am running Mac OS X Tiger 10.4.6 with all the latest update from Software Update which includes QuickTime 7.1.1.
    I am using QuickTime Broadcaster to stream back to itself (loopback) and record to disk at the same time. The input audio device is set to USB Audio CODEC (the default driver that comes with Mac OS X Tiger, and I am using an Alesis MultiMix 16USB mixer on a PowerMac Dual Core G5). I am using MPEG-4 Audio compression (no Video) of 16-bit, 44.1kHz and 128kbps (stereo).
    The problem is that I usually get recordings (ranging from 1.5 hours to 2.75hours long) with distortion. The distortion sounds like audio going through Logic Pro's BitCrusher plug-in, that is, audio recorded with less than 8-bit resolution but kept at 44.1kHz sample rate. Whether it overlays on top of the original audio or replaces it, I cannot tell, but the transition is instant and smooth with no audible clicks or pops. The distortion can come in and go randomly. For example, I had one recording with distortion coming in at about 2 minutes plus and it remained until about 2hr10min when the distortion went away. Sometimes it didn't go away; other times it came in about an hour later. I also had once where the distortion last only for about 6 minutes somewhere in the middle of a 2.25 hours recording...all in all, it occurs at random. And I do on rare occasions had distortion-free recordings.
    This problem also occurs on an iMac G5 with a Alesis MultiMix 12USB mixer, and in another Vara Software's Videocue PRO software which uses QuickTime for recording and playback. QuickTime 7.0.x and 7.1 also had this problem.
    Because of this problem, I may need to use a convoluted method to stream and record to disk via QuickTime. By the way, I also tried streaming to another local subnet IP address just as a troubleshooting without success.

    I too am having distortion problem (Sorry no solution here).
    Using OS 10.4.8, QT7.1.3, & Adobe Premiere 6.5 on a G4.
    After I down loaded QT 7.1.3, my problems started. Is this when your problems started too?
    Audio is in "slow motion" sound when editing. On rare occations, it sounds correct for 10 sec or so but sync is out and eventually reverts to "slow motion" sound. Even more bazar, when viewing a clip in a thumbnail preview, it works fine. So I know the orginal is good.
    My contention is QT is causing this. All I want is my previous version of QT back. I think this might fix your problem too. Unfortunately, there is no reinstall that I can find that takes QT 7.1.3 off and puts QT 7.1.1or2. The reinstall QT 7.0.3 which is on the Apple website will not restall.
    Looking for a reintall that will take QT 7.1.3 off, help anyone?

  • USB Audio CODEC replacement sw

    hello all,
    As it is demonstrated in the thread http://discussions.apple.com/thread.jspa?threadID=1129950&start=0&tstart=0 in the GarageBand discussion section, many users experience an intolerable static when using USB Audio CODEC for sound input. This was not the case in earlier versions and the consensus in that thread seems to be that something happened in OSX 10.4.11 that broke the codec. Since who knows when this will be fixed, I am wondering if anyone knows a source for an alternative, e.g. from some Linux source etc. I have been using an old Cube and I have no other way to get sound in but thru the USB port (methinks, or is there? FW?)
    Thanks

    But this mic is for Mac too. It's says that you "plug and play". I bought this microphone to record my music work at home.
    This is the website, It says that works fine with Garage Band but ...
    http://www.samsontech.com/products/productpage.cfm?prodID=1917
    *My english is not very good, I'm Spanish.
    Thank you!

  • I am using iMac OS 10.7.2 with Garageband'11 6.0.4. I can't record sound from  mixer Behringer X1622USB using USB out. when I connect the mixer to iMac via USB  appears USB Audio CODEC on Sound and preferences but no sound from mixer to iMac. Need help.

    I am using iMac OS 10.7.2 with Garageband'11 6.0.4. I can't record sound from  mixer Behringer X1622USB using USB out. when I connect the mixer to iMac via USB  appears USB Audio CODEC on Sound and Preferences but I can't get no sound from mixer to iMac only sound from iMac to mixer. I only can record sound using microphone line in. Please help.

    Eric,
    Thanks for your reply. Realtek audio works only in playback. There is a stereo mix in the mixer but the recording controls are not operable with no sliders in the mixer for any recording option. Slider controls appear to be grayed out. Can't figure out how to enable them. Downloaded newest drivers to no avail.
    The M Audio control panel has no apparent option for recording stereo mix. Adobe ignores the sound from the DVD or CD and shows flatline.
    I'm trying to record the sound from the DVD not rip the track.
    When I go to Audio Driver Setup and select Audition 3.0 windows sound, there is no input device installed.
    I'm thinking of going back to a decent internal Soundblaster card like I have on my 8 year old machine I am replacing.

  • USB Audio Codec DEMO driver

    Good afternoon. Today I bought a mixer Allen & Heath Xone 42. I am having problems connecting the mixer to my laptop. I use Mac Os Lion 10.7.4. When you connect the system uses the USB Audio Codec DEMO driver. Sound enters the mixer, but is accompanied by a constant beep. Every 30 seconds. This is the way and makes the mixer unfit for entry. Please help me resolve this issue.
    on the Internet found several similar complaints. Advised to remove the codec. But how to do it, I do not understand.
    In support of Allen & Heath wrote the following:
    Mac Pro, Mac OS X (10.7.4)

    But this mic is for Mac too. It's says that you "plug and play". I bought this microphone to record my music work at home.
    This is the website, It says that works fine with Garage Band but ...
    http://www.samsontech.com/products/productpage.cfm?prodID=1917
    *My english is not very good, I'm Spanish.
    Thank you!

  • USB Audio CODEC not being recognised.

    Hello,
    I have my my Wharfedale 802 mixer plugged into my MAC Mini (late 2012),  Processor - 2.5 GHz Intel Core i5, Memory - 4 GB 1600 MHz DDR3, via USB however it is not being recognised as USB audio CODEC what so ever. I have also tried searching for this to set the outputs in Logic and it is not recognised there either.
    I have just updated my iOS to Yosemite 10.10.2 and also my Logic X does anybody know why my mac is not recognising my USB audio CODEC for an input or output?
    Please help.
    Thanks

    I just posted this problem I had also. The USB audio Codec is for PPC macs only. I couldnt get a PYLE USB cassette deck to work in AUDACITY because it needed that codec.Windows users use this codec for many devices including the one you are trying to connect.
    My post in Snow leopard forum:
    I have come to the conclusion that this codec only worked on Macs that used PPC chips,not Intel Macs.Apple must have dropped it when switching to Intel.No where on the net can I find anything about this codec on newer mac OS's and newer Macs.
    Judging from this user's comment and others,they are working with OSX10.4 or newer OS that has PPC support like the first Mac Pro and other PPC's.I think the comments below answer my own original question.Hope this helps anyone with the same kind of problem with USB devices that need USB audio CODEC.
    In Audacity prefs, I selected:
    "USB Audio CODEC" for both Input and playback.
    I even tried lower sample rates and such. Record button stays grey and readouts don't show any input whatsoever even though I am sending a signal.
    Mac is a 533Ghz g4 (Digitial audio) running 10.4.11
    It is plug into a USB port on back of machine.

  • Usb audio codec mono only

    I am trying to connect usb record player. Apparently the usb audio codec that loads is mono only and shows up as being used with a usb mike. I am using an HP Touchscreen  model IQ526 with Vista 64 bit OS. Is there another driver that can be downloaded or another solution to the problem?? rayful27

    But this mic is for Mac too. It's says that you "plug and play". I bought this microphone to record my music work at home.
    This is the website, It says that works fine with Garage Band but ...
    http://www.samsontech.com/products/productpage.cfm?prodID=1917
    *My english is not very good, I'm Spanish.
    Thank you!

  • USB Audio Codec

    Compaq Pressario 5220, Windows Vista, 32 bits (approx. 3-4 years old)
    I bought a USB gramophone record player with a USB connection. This does only operate with a USB Audio Codec which I am supposed to find under Control Panel, Sound, Record.
    Alas!
    Any ideas on where to find/acquire such a codec?
    JoeyBr

    I have a Pyle USB cassette tape deck that needs this codec also to work with Audacity.I'm out of luck with the USB connection and have to connect it via RCA plugs to miniplug into Line In.
    I have come to the conclusion that this codec only worked on Macs that used PPC chips,not Intel Macs.Apple must have dropped it when switching to Intel.No where on the net can I find anything about this codec on newer mac OS's and newer intel Macs.
    Judging from this user's comment below and others,they are working with OSX10.4 and PPC's like G3,G4 and G5.Also later versions of Mac OSX that had support for PPC's like the first Mac Pro.
    In Audacity prefs, I selected:
    "USB Audio CODEC" for both Input and playback.
    Mac is a 533Ghz g4 (Digitial audio) running 10.4.11
    It is plug into a USB port on back of machine.
    Attached is a screenshot from Audacity and it shows the USB Audio Codec. I was pulling my hair out,wondering why I couldn't see it in my audio sound setup in OSX 10.6.8 on my black Macbook.I couldn't find it in my system anywhere.This attachment showing the codec installed MUST have been done on a PPC G3,4 or 5. Nowhere does it exist on Intel Macs.
    Disregard the red circle.

  • Where do I find USB Audio codec in OSX 10.6.8?

    I need this for a Pyle USB tape deck (PT-659DU). Audacity is the only program that can be used with this deck and they show clearly how to use Audacity with     USB PnP devices,as this deck is one.This screenshot shows what I need to do.(find the USB Audio codec,and get it to show in the Audio setup in Sound
    Prefs.

    My last post to myself is wrong.I received a response from Audacity with USB audio Codecs support for Mac OSX on intel Macs.
    Apple Developer Technotes link below.
    On 22 February 2015 at 15:34, Ross Wright wrote:
    My only question is,was he using a Powermac G3,G4 or G5 PowerPC based computer to show the USB audio codec installed? Mac Intel with OSX does not have USB audio codec in it's sound codecs anymore,nor does it support this codec anymore for usb record recorders & Tape recorders.
    From Audacity:
    Sorry, but that is just not true:
    https://developer.apple.com/library/mac/technotes/tn2274/_index.html .
    It must be PPC only to work with Audacity.Ask any user with problems finding this codec to install and you will find they have an intel based Mac.
    Please correct me if I am wrong.
    Add to your list of unsupported Cassette players. Pyle PT-659DU. There will be other models similar to this one with the same issue.I had to go analog RCA to work properly with Audacity.
    See:  http://wiki.audacityteam.org/wiki/User:BillWharrie/OSX_and_USB_input_devices
    Pyle devices most likely just use the Mac's USB audio class driver as above.
    However if your device's manual says you need to install a special driver for
    Mac, you should do that.
    In many cases, it's as simple as replacing the USB cable.

  • USB Audio Codec can't be found...

    I have a USB Dual Pre and I can’t record any audio into my software because my ‘USB Audio Codec’ is gone or not showing up. Any way to get it back? Or is there any other way to record using my usb input now?

    Check it out again to ensure that your Bounce are in the right path...Bounce or export it into your/user Dekstop!!
    Normally,for that case,you doesn't choose your path..so it'll auto save in the Bounce folder~User-yourname-Music-Logic-Bounces
    check out man.
    cheers

  • I upgraded to yosemite and iOS 8 in order to record with quicktime. But when I select Record a new movies I immediately get an Operation Could not be completed error.

    I upgraded to yosemite and iOS 8 in order to record with quicktime. But when I select Record a new movies I immediately get an Operation Could not be completed error. When I choose record audio or screenshots, I get a little further, but as soon as I select my ipad as the source I get the same error message.

    You don't need to be a developer for this to work. I get the same error. Just one more thing on the list that make me upset more and more with Apple. Things just don't work out of the box like they used to.
    This new feature was to be included with iOS 8 and Yosemite.

  • USB audio Codec bug in Leopard

    Does anybody know when Apple are going to fix the "USB audio codec" bug in Leopard? I has a USB mic that get a annoying scratchy noise after 5-10 minutes when I record in Garage Band and Logic.

    But this mic is for Mac too. It's says that you "plug and play". I bought this microphone to record my music work at home.
    This is the website, It says that works fine with Garage Band but ...
    http://www.samsontech.com/products/productpage.cfm?prodID=1917
    *My english is not very good, I'm Spanish.
    Thank you!

  • USB AUDIO CODEC PROBLEMS

    A few days ago I bought an USB Microphone (Samson G-Track). I don't know why It doesn't work. When I select in Sound/Preferences/Input the "Usb Audio Codec" but It says that there aren't input controls in the device. I tested it at Garage Band but It didn't work. I thought that the mic was defective but when I tested it in my mother's pc (Vista) It worked.
    It's says that you "plug and play" in Garage Band. I bought this microphone to record my music work at home.
    This is the website, It says that works fine with Garage Band but ...
    http://www.samsontech.com/products/productpage.cfm?prodID=1917
    *My english is not very good, I'm Spanish.
    Thank you!
    What can I do?
    Thank you.

    Hi Rhea91-
    Your English is indeed very good
    Are you plugging the Mic directly into a USB port on your Mac? Are you certain there are no Mac-specific drivers? "Mac compatible" can mean many things. Is the device OSX 10.5.2 compatible?
    Luck-
    -DaddyPaycheck

  • Usb Audio Codec doesn't work

    A few days ago I bought an USB Microphone (Samson G-Track). I don't know why It doesn't work. When I select in Sound/Preferences/Input the "Usb Audio Codec" but It says that there aren't input controls in the device. I tested it at Garage Band but It didn't work. I thought that the mic was defective but when I tested it in my mother's pc (Vista) It worked.
    What can I do?
    Thank you.

    But this mic is for Mac too. It's says that you "plug and play". I bought this microphone to record my music work at home.
    This is the website, It says that works fine with Garage Band but ...
    http://www.samsontech.com/products/productpage.cfm?prodID=1917
    *My english is not very good, I'm Spanish.
    Thank you!

  • Is it possible to rename USB AUDIO CODEC to something more memorable?

    Hi there
    My system is getting very confusing with so many selectable USB AUDIO CODECs all named
    "USB Audio Codec"
    (USB Alesis M1Active 520USB Speakers, Yamaha Audiogram3 USB Audio Interface)
    Is it possible to rename them so I know which one is which as I'm spending so much time going through each one to find the right Input/Output.
    Thanks!

    My guess is that OS X gets that name from the driver of that Device itself. If that is the case, then you can't rename it. This is the same problem with various MIDI devices that are displayed in Logic with the weirdest names.
    However,
    you can use a trick if you really want to rename a device so when you open GarageBand it says "My beloved Device". Create an Aggregate Device in the Audio MIDI utility with only that one device. The advantage is that you can rename an Aggregate Device - Voila.
    Hope that helps
    Edgar Rothermich 
    http://DingDingMusic.com/Manuals/
    'I may receive some form of compensation, financial or otherwise, from my recommendation or link.'

Maybe you are looking for