Distribution Builder looking for product installers

I'm having a problem building a distribution.
The builder is asking for product installers that were part of a different distribution and no longer
on the machine. Its looking for the NI-DAQmx Core Runtime 9.6.2 and the Ni-VISA Runtime 5.3 installers.
How do I remove the dependency of the previous distribution. In the Drivers & Components tab of the Installer
the change Source button is disabled how do enable it.
I'm running CVI 2012 on an XP machine. I appreciate any help .

Hello chetp
This might help:
http://digital.ni.com/public.nsf/allkb/E2D8B36AE74458C8862573A8005C4708?OpenDocument
Regards
Mart G

Similar Messages

New Build - Looking for Tips

So I have purchased the components listed in my Sig and getting ready to set everything up, just wanting to get some tips/advice on the best way to go about it.
My biggest question is concerning RAID, as this is the first time I have set one up. Any tips, guides, etc. on how best to accomplish this on my MB is appreciated. I am wanting to end up with a 1TB RAID 1+0 (4 500GB drives paired up, both pairs RAID 1, then one pair RAID 0 of the other pair). Am I correct in assuming it is best to plug only 2 in (SATA 1&2) setup the RAID 1 on those, then plug the other 2 in (SATA 3&4) and set those up as RAID 1, then tie everything together as with RAID 0? Or can I plug them all in and do it all at once? The instructions look fairly straight forward, just looking for some clarity and actual user input.
Do I need to update my BIOS? I haven't tried booting at all, so not sure what I am starting with, but I notice in the CPU compatibility the same CPU I have lists Version 10.4. Should I stick with what I have and only upgrade if I am having issues, or should I upgrade from the start.
I have a SATA Blu-Ray burner, and have seen a few things mentioning a SATA ODD coming up under RAID configurations. Is this an issue, is there a certain SATA port I should use to avoid this, certain settings I need to pay attention to, or does it matter?
Regarding memory, I read (in a sticky) that fewer memory sticks result in faster performance due to Dual Channels. I was under the impression that if all 4 slots were filled you would have 2 groups, each using Dual Channel. Am I incorrect in that? If faster performance (MHz-wise) is achieved by only using 2 sticks, will I get better overall results by removing 2 sticks (leaving only 4GB) or will the additional memory compensate for the speed loss? (The RAM is rated as being Dual Channel, if that makes a difference).
Does anyone have any general computer building tips? I have built a number of them before, but would like some input on the best/most efficient/fewest problems way is. All previous builds have been done with default configurations, if anyone has suggestions for some settings that they recommend those are welcome. I will be over-clocking at some point, depending on how things go and if there is any advantage to doing so from the start or waiting until the system is setup. I did notice this MB has a OC center as well as the Easy OC Switch. Any input or thoughts on those?
To sum it up, I am looking for as much input on getting everything set up as easily as possible, with the best settings without requiring a lot of adjustments. Any and all input is appreciated!

Quote from: Bas on 22-September-10, 15:45:56
Windows rating is rather silly, it's not the sum of the system but rather the slowest part that gives you this rating.
Yeah, I agree with the silliness of Windows final rating, however I do like to use the individual ratings as a sort of benchmark. The issue isn't the final rating, it the rating I am receiving for my processor, which is 4.1, and is the lowest rating on there.
From memory -
Processor - 4.1
RAM - 4.9
Graphics - 7.4
Gaming - 7.1
HD - 5.9
As a comparison, another computer with a 2.2GHz quad core processor, 4GB RAM, and single drive rates as follows:
Processor - 6.9
RAM - 7.2
Graphics - 4.8
Gaming - 6.1
HD - 5.9
With the components I have vs the comparison computer, I would expect CPU, RAM, and HD to all be higher, but they are lower or the same! So something somewhere is not right in my opinion.
Thanks for any feedback!

Looking for product recommendation

Hello,
I'm looking for a product recommendation and configuration suggestions. I'd like to provide wireless access to the Internet (as well as our internal network) to people who bring their laptops and other wifi devices into the office.
Our network currently looks like this:
Internet --- DSL modem --- Firewall --- Switch --- Users (wired)
Which product should I use, and where should I place it in our topology? Between the firewall and switch?
Thanks,
Steve
Message Edited by generaltab on 09-10-2008 04:30 PM

You use WRT300N router and replace the firewall or place after the firewall on the queue you have specified and then connect the switch to router. Linksys routers have inbuilt firewalls.

Looking for productivity ap for iPhone

Looking for an iPhone ap that I can use with my calendar and spreadsheet. I meet with clients on a weekly basis and want to track my hours that I meet with them from my calendar to a spreadsheet. To be specific, I want to put the client in my calendar for 1:00 pm to 2:00 pm every Tuesday and Thursday and have it sync to a spreadsheet that will account for each client by hours. I've been told that there are aps for this for iPhone. Thanks!

You could do a search on AppShopper.com to see if there is anything that meets your needs.

Distribution and software for production webserver

I am just wondering what (linux) distribution do you use on the production webserver(s). Could be your own or at work.
Also what you use: apache, nginx, or something else?
/LATER Would be nice to see what database do you prefer: MySQL, PostgreSQL or other?
Last edited by Cosmin (2010-11-13 00:15:44)

Thanks everyone
So until now
OS:
Arch [2]
Debian [2]
CentOS [2]
FreeBSD [1]
OpenBSD [1]
web server software:
Apache [3]
nginx [1]
database:
Last edited by Cosmin (2010-11-11 10:11:12)

Would you use Flash Builder Beta2 for production project?

i am currently developing a project in Flash Builder beta2 with flex 4 sdk with the new spark components.
But as i can see not all mx components have a spark equivalent and in my bin-debug folder there are
spark_4.0.0.10485.swf 431,927 bytes
rpc_4.0.0.10485.swf 206,435 bytes
framework_4.0.0.10485.swf 1,018,863 bytes
without taking in mind my main application file sizes.
An i am wondering will my project that use a mix of mx and spark components will have to load the hole frameworks?

i've got the same pb... any ideas ?

Looking for product to page thru phones

We have an office that requires paging thru phones and does't want to hang speakers.
We have CUCM7.1
Are there any good paging systems anyone can recommend?
Thanks
Matt

This isn't actually a function of the Wireless adapter and more related to the PC Operating System.
If you are running a Window PC this is easy. Since Windows XP Internet Connection Sharing has existed. This is simply a matter of enabling Internet Sharing on the LAN adapter and setting the Home Network Connection to the wireless adapter. Then you will need to add a Ad-Hoc wireless network for your client devices to connect too. I suppose the wireless adaptor needs to support Ad-Hoc wireless networks but I think they all do.
Linux\Mac have similar Internet Sharing support.
There is also software available that you can install to create a wireless hotspot with your PC.
Please remember to Kudo those that help you.
Linksys
Communities Technical Support

Looking for Third Party SAP Data Migration Tools

Hi all,
I don't know if this is the right place but I was wondering if anyone can provide me a list or a link of the different third party SAP Data Migration Tools. I am specifically looking for productions that migrate data from one SAP system to another.
Thanks and I hope to hear from you.
Regards

Hi,
Just to weight out my options and compare the diffrent products as a research of sort.
For SAP tools they use LSMW I believe but I want to check the alternatives.
Regards

Xcode misplaces embedded.mobileprovision file on distribution build

Hi,
I have two apps (free and paid versions), Snatch and SnatchTest which are two targets of one Xcode project (the project name is Snatch.xcode). I'm about to submit an update to the App Store so I did a Distribution build. For Snatch it worked fine, the bundle contains the embedded.mobileprovision file, but for SnatchTest when I did the build (after cleaning all the targets, quitting and restarting Xcode, even restarting my computer) the SnatchTest bundle shows up without an embedded.mobileprovision file. However in the build directory another app bundle appears with the name of Snatch, containing the embedded.mobileprovision file (and nothing else).
By the way the same thing happened to me a couple of times when I submitted the original 1.0 versions, but when I quit Xcode and restarted the problem went away. Now it just won't go away. So I'm thinking what to do. It seems that the embedded.mobileprovision file was simply misplaced by Xcode, so I figure if I can't get it to work I'll simply move it to the SnatchTest bundle, submit that and explain in the submission notes (under the "Demo account" field which I presume the Apple people read) what happened and hope for the best.
However, in the meantime I wanted to know if by any chance anyone has had this same problem, what they did to fix it and what happened in the end.
Thanks!

Took me forever to figure out what was going on. Boo. I reported it. Apple confirmed as a bug. So just use your work around for now.
When I do a release, I delete all the targets I don't want. Close the project. Re-open the project. Build my distribution build of that target. Then revert back to an older version of the project file. But dragging it to the top of the list may be an easier fix if that works every time.

The Distribution Kit Builder is Looking for the NI Variable Engine in an old distribution, cant find it and fails to build

I am unable to build a distribution kit because the builder appears to have saved a path to the NI Variable Engine which is not valid. I appear to have the NI Variable Engine installed. There are NI Variable Engine 2.5.0 .xml files loaded in on my computer (See attached for listing of drivers loaded). I do not seem to be able to break CVI's Link to my past installers for getting drivers. I've tried creating a new installer but had the same trouble.
I am running a 64 bit Laptop with Windows 7, building a 32 bit application, running CVI 2010.
Solved!
Go to Solution.
Attachments:
ATAHM Outline.ppt ‏61 KB

The default path is the path to whatever distribution installed NI Variable Engine on your machine. For example, if it was installed from a Driver Disk, the path would probably be D:\. However, from the images you originally posted, I can see that you were being prompted to provide the path to one of your earlier ATAHM distributions. It was looking for it at this path:
c:\Users\chill\Documents\Development\AATAS\ATAHM\distributions_ATAHM\ATAHM Oct 24 2011\
Do you still have that distribution? If you can point it to that distribuiton, you should be good.
Now back to the error you were seeing... Your version of that .NET manifest file matches (except for the version number) Revision A from the Knowledge Base, so you should try replacing it with Revision B (and rename it to NI .NET Framework 2.0 Language Pack x86 Installer {F8ECD2D6-659C-49EB-8454-5F8F7B526FCF}.xml). Make sure you restart CVI after swapping the file. I would expect that to solve your problem. If it doesn't, you'll have to let me know what the new issue is, or if you're somehow still seeing the same error message.
Mert A.
National Instruments

LabVIEW cannot locate some components necessary to build the installer - looking for "Setup" installer

Hi,
I have an application that has been upgraded to LabVIEW 8. I have previously been able to build the exe and installer but recently the installer part of the build has been failing with the following error message:
Unable to locate the installer source for "Setup" distribution.
Locate the distribution and try again
The dialog includes a file path prompt that is pointing at the Installer\Volume directory where Installer is the target directory for the build. The installer build is configured to span CD-sized volumes (650MB)
There are no sources or support files named anything like Setup that I can see.
The installer includes DaqMX and the LabVIEW 8 runtime engine as additional installers
The build works ok If I turn off the DaqMX driver installer
Cheers,
Brett Percy
Senior Software Development Engineer
Certified LabVIEW Architect and LabVIEW Champion

Hi Andy,
I've upgraded DAQmx to 8.0.1 and the installer build now works....sometimes.
And sometimes it gives me a different error:
CDK_Build_Invoke.vi.ProxyCaller >> CDK_Build_Invoke.vi >> CDK_Engine_Main.vi >> CDK_Engine_Build.vi >> NI_MDF.lvlib:MDFBuildDist_Build.vi
Loading product deployment information
Loading product deployment information
Loading product deployment information
Loading product deployment information
Loading product deployment information
Adding files to installer
Done adding files
Preparing to build deployment
Copying products from distributions
Copying distribution 'NI-DAQ 8.0.1' from: C:\Documents and Settings\brettper\Desktop\NIDAQ801\8.0.1\ to: C:\Documents and Settings\brettper\My Documents\Work\Deakin University\433 VuPlate Software Upgrade\builds\VUPlate\VuPlate Installer\
Copying distribution 'Setup' from: C:\Documents and Settings\brettper\My Documents\Work\Deakin University\433 VuPlate Software Upgrade\builds\VUPlate\VuPlate Installer\Volume\ to: C:\Documents and Settings\brettper\My Documents\Work\Deakin University\433 VuPlate Software Upgrade\builds\VUPlate\VuPlate Installer\
Building deployment
Copying setup files
Setting merged database information
Setting product information
Setting developer part information
Starting final build
Validating...
*** Error: An internal tool or library returned an error. (Error code -21)
Error Messages
Input directory 'C:\Documents and Settings\brettper\My Documents\Work\Deakin University\433 VuPlate Software Upgrade\builds\VUPlate\VuPlate Installer\Volume\bin\p2' not found for part 'palSetupLVRT.msi' in product 'C:\Program Files\National Instruments\Shared\MDF\Manifests\NI-PAL for Phar Lap ETS {3263845B-95F2-43C0-817E-B7BF25BCB742}.xml'.
Input directory 'C:\Documents and Settings\brettper\My Documents\Work\Deakin University\433 VuPlate Software Upgrade\builds\VUPlate\VuPlate Installer\Volume\bin\p3' not found for part 'infInstaller.msi' in product 'C:\Program Files\National Instruments\Shared\MDF\Manifests\NI-DAQ INF Files {2146CF1A-5ACD-4A50-8B36-6A7DD095B08C}.xml'.
-- SNIP --
Input directory 'C:\Documents and Settings\brettper\My Documents\Work\Deakin University\433 VuPlate Software Upgrade\builds\VUPlate\VuPlate Installer\Volume\bin\p43\nilm' not found for part 'nilm.msi' in product 'C:\Program Files\National Instruments\Shared\MDF\Manifests\NI License Manager {FB6DF036-C3A7-4A89-92DA-B4364A8E9373}.xml'.
Input directory 'C:\Documents and Settings\brettper\My Documents\Work\Deakin University\433 VuPlate Software Upgrade\builds\VUPlate\VuPlate Installer\Volume\bin\p44\LVRealTimeErrorDialog' not found for part 'LVRealTimeErrorDialog.msi' in product 'C:\Program Files\National Instruments\Shared\MDF\Manifests\NI LabVIEW RT Error Dialog {3DFF45F7-C12C-4A3A-BA9E-1946A4E92424}.xml'.
Input directory 'C:\Documents and Settings\brettper\My Documents\Work\Deakin University\433 VuPlate Software Upgrade\builds\VUPlate\VuPlate Installer\Volume\bin\p45\LVBrokerAux800' not found for part 'LVBrokerAux80.msi' in product 'C:\Program Files\National Instruments\Shared\MDF\Manifests\Broker Aux 8.0 {88BBB9A9-C034-466E-BB83-8197AFD1669C}.xml'.
*** End Error Report
Done building deployment
And underneath all this (in the Details of the Build Errors dialog) I get
"Visit the Request Support page at ni.com/ask to learn more about resolving this problem. Use the following information as a reference:"
followed by nothing...
So it's sort of working but not entirely reliable. I think I've seen the path to the DAQmx installer in the Additional Installers tab replaced with the path into the installer build directory I was being prompted with earlier but I haven't been able to replicate this.
Senior Software Development Engineer
Certified LabVIEW Architect and LabVIEW Champion
Attachments:
Full error listing.txt ‏16 KB

Looking for a simple tutorial to building my first responsive web site in Dreamweaver CC.

I am looking for a simple tutorial to building my first responsive web site in Dreamweaver CC.
I have watched the tv.adobe video 3 times and I cam not able to do the actions the author shows.
help.
Ken Edwards

Responsive and simple don't go hand-in-hand. First do some prep-work to understand the concepts.
Responsive Web Design
http://coding.smashingmagazine.com/2011/01/12/guidelines-for-responsive-web-design/
Introduction to CSS Media Queries
http://www.adobe.com/devnet/dreamweaver/articles/introducing-media-queries.html
Jump start your RWD projects with any of the Responsive Frameworks below:
Foundation Zurb
http://foundation.zurb.com/templates.php
Skeleton Boilerplate
http://www.getskeleton.com/
Initializr (HTML5 Boilerplate, Responsive or Bootstrap)
http://www.initializr.com/
DMX Zone's Bootstrap FREE extension for DW
http://www.dmxzone.com/go/21759/dmxzone-bootstrap/
Project Seven's Page Packs (Commercial CSS Templates)
http://www.projectseven.com/products/templates/index.htm
Have fun!!
Nancy O.

Looking for Script Exchange-2007: Import-Mailbox Calendar Folder on multiple mailboxes {Distribution Group}

Hi,
I'm looking for a PowerShell script which will import a Calendar events into student's mailbox (Calendar). Those students are located in a distribution group and I would like to target the distribution group; I'm trying to simulate what I want to achieve
in the below code example, I would appreciate if anyone jump in and advise.
$Users = Import-Csv C:\users.csv | ForEach-Object{Get-DistributionGroup -Identity SC-1213} | Import-Mailbox -Identity $Users -PSTFolderPath c:\Calendar.pst -IncludeFolders '\Calendar' -StartDate -EndDate
Much appreciated..
Hussain

The logic doesn't work unless you are using StartDate and EndDate for the period when you change the item. As I said above, StartDate and EndDate are not the times when the meeting starts and ends - they are the times that the item was either added
or modified in the mailbox. Your filter was trying to pull items that were in the future.
And as I also said above, if you import a modified item, the original is
not going to be updated. You will have a duplicate meeting
on the calendar. You would have to remove the original
and import the updated item if this was how you wished to manage the updates. This is not nearly as effective as
sending meeting requests and updating those meetings.
For example, if we do things the way you are doing them, and we add a "Student Appreciation Bonfire" meeting to the calendar for April 12 at "The Quad", we would do the following:
On February 1, you get information for the meeting that needs to be imported
You create this new meeting in the PST calendar - "Student Appreciation Bonfire"; Date April 12, start 8:00 AM, end 12:00 noon; Location The Quad
You import the PST into everyone's calendar
You receive a note on March 12 saying the venue has changed to The River Beach, so you update this meeting in your PST
Since there are other calendar items in the PST, you import the update using StartDate of March 12 and EndDate of March 13 - the date that you changed the item, not the date the item occurs
At this point, all users have two meetings on their calendar - the original and the update
If, instead of doing it this way, you create a Student Actvities Calendar mailbox, you would handle it this way:
On February 1, you get information for the meeting that needs to be imported
You create this new meeting in the Corporate calendar - "Student Appreciation Bonfire"; Date April 12, start 8:00 AM, end 12:00 noon; Location The Quad
You invite everyone to the meeting
You receive a note on March 12 saying the venue has changed to The River Beach, so you update this meeting in that calendar and send out the update
At this point, all users have only the one meeting on their calendar - the update
Using the PST as the source for the meetings would work only for items that
will not be changed - holidays are a good example.

Looking for App builder

HI...I am new to community. I am looking for someone to build an app for my sales team. I have about 300 people who are in and out of retail stores and I would like to develop a standard retail audit form that they could fill out on the go. Please let me know cost, timing, and other considerations. I work for a large firm so someone who is familar with typical IT organization. thanks Ted

Hi and welcome to the forums!
A couple of places for you to visit: Blackberry 101 Tips & Tricks
Have you tried: BB Applications or BB Development
Happy to have you here!
IrwinII
Please remember to "Accept as Solution" the post which solved your thread. If I or someone else have helped you, please tell us you "Like" what we had to say at the bottom right of the post.

Maintaining Remote key in look up tables for Production data

Hi,
me
SEE in DEV and QA to maintain the Remote key for Look up tables.First i have exported those look up table values and again imported with mapping Remote keys (clone the field and map it to Remote key.). By this i have maintained the Remote keys to all look up tables. Now for Production what should i do. Is it the same process extract all records from production into our desktop and then again import it using IM, clone the field and map it to Remote key.
1. Is this the right process?
2. What happens if there are huge data present in production how to proceed furthr then?
Required your suggestion please.
Thanks,
Pradeep

HI Pradeep,
I dont see any problem with this method if I am getting it right
You are updating remote keys by reimporting lookup data, and this way you have multiple remote keys for data in lookup table,right?
This will help you to automap entries in Import process for different Remote systems.
I did not get your 2nd point?
Thanks,
Ravi

Distribution Builder looking for product installers

Similar Messages

Maybe you are looking for