Dj mix recording

i was told it was possible to hook up my mixer to garage band and record...is it true, because i cant seem to figure it out and i would really like to.
thanks:)

plug the console into the Line-in on the mac and:
http://www.bulletsandbones.com/GB/GBFAQ.html#recordlinein
(Let the page FULLY load. The link to your answer is at the top of your screen)

Similar Messages

How do I get my old Surround Mixer recording sources back?

I recently had my computer repaired where I basically had a complete overhaul. In the process they installed a second soundcard (the one that went with the new motherboard) alongside my original Creative Sound Blaster Audigy card (Sound Blaster Audigy Platinum eX). Before, when I would record audio into my computer, I opened the Surround Mixer software and in the record pulldown menu it showed all of the inputs as they relate to my Audigy interface (SPDIF, Aux In 2, Line In 2, etc.). Now when I open the Surround Mixer software, I only get generic options such as Analog Mix, CD Digital, Microphone, etc. and therefore I can't get any outside audio into my computer.
I figured the computer?was defaulting to the?new sound card so I disabled the onboard audio in my BIOS and then installed the Creative Sound Blaster Series 2 Driver. I clicked on the driver and it said that it needed to uninstall another driver that was already there. The install went a little funny and it got hung up a couple of times. Then, I couldn't get Surround Mixer to work at all so I went to the Creative website and installed Software Auto Update. I downloaded and installed all the critical components?but that also went a little funny. It took about three tries and it didn't seem like it actually finished installing, but when I checked on Auto Update again, it said that I was up to date and that everything had installed. I noticed at the beginning that it installed a new version of Surround Mixer but when I opened it later, it still had those same generic options, not the the ones that match my external interface.
What do I need to do to get my original settings back?
Message Edited by audiodrome on 04-30-2009 06:46 PMMessage Edited by audiodrome on 04-30-2009 07:32 [email protected]

>Re: How do I get my old Surround Mixer recording sources back?p audiodrome,
Is the external Audigy Dri've properly connected? Does the Plat Ex have the rear jacks? If so, can you record from the rear LineIn or mic jack and play sound files through headphones or speakers? What happens when you run the Creative Diagnostic? What does Device Manager show? Otherwise, yes, uninstall and reinstall the Creative software. If your install CD has a repair option, try that first. However, you may find you need to remove the Audigy from your PC, reboot without it, and then reinstall everything. Some Soundblaster cards don't play well with some integrated soundcards, so you may also want to disable the integrated soundcard in BIOS.
Message Edited by Katman on 05-04-2009 :00 AM

Is there support to stereo mix record channel for windows vista or at least XP ?

i have lenovo N500 and conexant HD smartaudio 221 on board with windows vista.
i read somewhere that smartaudio don't support stereo mix record channel in their driver for vista.
do they support the stereo mix record channel for windows XP ?
(i tried to ask them in their site, but couldn't manage to do that)

Audigy 4 Analog-Mix - Recording independ

hi folks!
I hope you can understand my english, 'cause I'm german!
my problem:
I need the "analog mix" (line-in) from my audigy 4 to record sounds from a radio station. I'm using the Creative "Smart Recorder" from the "Creative Media Source Go"-software-package. When ever I'm choosing "analog mix" as recording-source, my card records everything going out & coming in by this card. When I'm starting a game or watching a movie while recording from "ANALOG MIX" (=LINE IN), my card records both, the line in - signal and the sound that is played by the movie or by a game f.e.
Also: when I open the volume control (play-back, not recordinig) and turn the slider for "analog mix"-loudness to zero, the card doesn't record any signal any more. That means, the playback and recording aren't independent. But I need this function because I want to use my PC "normaly" when recording from the line in.
What I am doing wrong? Message Edited by snoop on 02-23-200604:2 AM
Message Edited by snoop on 02-23-200604:22 AM

Hhm I can't understand that!
There is also a "what you heare" available as the record-source. That thing records everything (incoming and outgoing).
With every (simple) onboard-Soundcard I used I could record from the line-in while playing something other to the line-out and all was idenpently. Also I could turn the playback-volume (from the line-in) to zero while the record-volume is still at the position it's needed for recording and it worked.
I've bought the Audigy 4 some weeks ago to get a better Input-Signal (and it's even very better), but I didn't know that I wont be able to record and playback at the same time. That's a pity
Only the Mic-In can be recorded this way but I can't use the Mic-In for my Radio-Signals because it's too strong.Message Edited by snoop on 02-23-200604:23 AM
Message Edited by snoop on 02-23-200604:24 AM

Digital mixer recording

I bought me a Yamaha 01V96 digimixer, and would like to use its full functionality for recording.
After searching a bit online, i found out that you can via ADAT out of the mixer send up to 8 channels into a single unit.
But how do I get the ADAT in to my computer so software like Logic / GarageBand can understand it?
I know there are firewire/usb interfaces.. But i'm not sure wich will work?

studsgard wrote:
Would this for example work?
http://www.thomann.de/gb/behringer_fca610.htm
No, that only has a stereo digital input output. The next model up does have ADAT. Behringer FCA 1616
http://www.sweetwater.com/store/detail/FCA1616?device=c&network=g&matchtype=&gcl id=CO_I_uDT-78CFQimaQodxnMA-g
ADAT I/O is 8 channels

Very Strange - Mixer Record Source Setting Will Not Save - defaults to Microphone volum

This issue has me stumped.. I've even tried a clean boot of XP.
Firstly, I am using X-Fi Platinum, on XP, ASUS board
The problem is that both in Control Panel and in Creative Mixer, any changes made to the recording source will not save. In other words, when I close down the Mixer and re-open, the default source is Microphone with volume 0. Even if all I do is increase the microphone volume, when I close that window down, it becomes volume 0 again. When I try the approach through Control Panel it is the same result. The microphone is not "mute" but the volume slider is all the way down to minimum, so its the same result. Also, if I change the recording source to "What You Hear" or "Mic 2" , as soon as I close down the mixer window, it is back to Microphone volume 0
The strange thing is, I formatted my hard dri've and re-installed XP, and still I'm having the same problem.
Thanks in advance for your help..

I finally discovered the problem. It is the BlueBeat player that was responsible.
Here is an exerpt from a press release:
"Bluebeat.com uses MRT?s X SeCure technology which makes it next to impossible for an average user to save, record, convert or otherwise ?transcode? the audio streams on the Bluebeat.com"
But the problem is that it effects the OS at such a low level that doing a "clean boot" still does not fix the issue.
Keep in mind, that the BlueBeat player wasn't even running when it caused these issues. Fortunately, when I uninstalled BlueBeat, everything works fine again.
Moral of the story? If you have X-Fi, avoid BlueBeat.com, because you will lose all ability to record, even when not running their player. I hope this helps some people out there.

No externel mic no audio mix record. HP dv6

I have problem recordind on my dv6 i5. No external mic or stereomix record my audio. Only mic on my laptop works fine
I have latest driver installd - syst - wind 7 64

whats your product number
whats your sound card?
main problem would be " recording is not recording playback of main device"

Mixing Recording VoCals

Anyone know of any neat tricks or any good tutorials?
Just looking for a couple suggestions...
-Brandon

www.macprovideo.com has some excellent tutorials

Multiple input device recording/mixing help in Audition 5.5

I'm presently evaluating Audition 5.5 and haven't been able to find any information pertaining to what others MUST do everyday.
I'd like to use Audition to record simultaneous tracks from different sources (microphones). I'm using several USB sound card dongles (each with a single 3.5mm stereo microphone input and headphone/speaker output) as quick and convenient method of creating an array of microphone inputs. Each dongle appears as a discrete audio device with a corresponding input and output.
Fine so far.
Where I'm struggling is in trying to map each microphone to discrete mixer channel. I choose Edit->Preferences->Audio Channel Mapping, but it seems that only channels from any one particular sound device may be mapped to mixer channels at any time. If I assign the microphone from sound card A to Track 1, I can't assing the microphone from sound card B to Track 2. When I try, it alters the hardware device selection and negates any prior channels I've mapped that aren't part of the same device. I hope I've explained the situation clearly.
I'd like to map the microphone from sound device (dongle) A to Track 1, the microphone from device B to Track 2, C to 3 and so forth. But I cant' seem to figure out how to make Audition simultaneously recognize more than any one sound device at any particular time.
Is there a way to do what I'm trying to achieve? Does Audition not support simultaneous mixing/recording from multiple hardware devices? If not, do other products exist that DO support the configuration I'm trying to create which I can use as a front-end - to later mix-down in Audition?
I'd greatly appreciate any helpful insight, guidance, suggestions or recommendations.
Thanks!

remford wrote:
I'm not having any SYNC problems that I'm aware of...
Of course you're not - that's because the system prevents you having them by limiting the physical sources you can use!
Here is a brief explanation of the sync problem - I hope it makes sense:
When an input device digitises a signal, it has to provide a clock source for its A-D device. Normally this clock is locally derived, and the device outputs a digital stream at that rate. But if you have two devices (let's say that they were two external USB ones) both trying to be the input device, then their clocks won't be synchronised - inevitably. Audition, and all other software come to that, can only record at one rate, and if another device provides an input that isn't exactly at the same rate and phase as the one providing the master clock, then fairly soon, you get to a point where the data being inputted won't coincide with the main clock any more, and a bloody great click occurs. On older systems where you could use multiple devices, some allowed for the clock sources to be externally synchronised, and a lot of pro gear still does - it helps a lot when you are using digital mixers and external digital preamps if you can feed everything from a master clock, rather than daisy-chaining it.
When it comes to ASIO, Steinberg made the relatively easy decision not even to try to implement it for multiple devices. Instead, they suggest that you use a single device which is capable of supporting as many inputs as your PC can manage. As an example of how this works, my MOTU device that I mentioned above has eight analogue inputs, and also an 8-channel ADAT input. So, without too much trouble I can connect an external 8-channel digital preamp to it and have 16 inputs in total. It uses an optical connection for the ADAT, but to use it I either have to provide sync from the MOTU to the preamp, or use the preamp as the sync source for both itself and the MOTU, replacing the internal clock. With the only digital preamp I have it's this latter option that makes sense, as there isn't an easy way to get sync from the MOTU back to the preamp. (I should perhaps explain that the preamp has got a sync input, but the only sync output from the MOTU comes from its ADAT output, and that isn't easy to feed back in).
Yes, until you get used to it the concept of syncing devices takes a bit of getting used to - Steinberg's idea was to keep it as simple as possible, even though on the face of it, it's rather frustrating.

Audigy 4 Pro Low Recording Levels/Master Knob/OSD probl

I purchased a second-hand Audigy 4 Pro. I was not given the software disk but managed to install the latest drivers and get it to play MP3s. I use Adobe Audition to record my old tapes to MP3 and record my attempts at guitar. With my SBLi've I had no problem. I bought the Pro because of the ease of using the breakout box. However I have some quesions about some problems I am having. ) Since I have no Creative software, just Win XP Mixer I don't seem to be able to control the input levels from either the mixer or the box. I have a tape deck using RCA to Line In 3 and an electric and acoustic guitar to Line In 2. The mixer record levels seem to have no effect. I can record but nothing seems to be much more than -20db or so at most. Could this be because Adobe Audition only shows Line In 3 L (ie one channel only)? Could this be because of the much greater dynamic range of the Audigy 4 compared to the SBLi've Value? Do I need additional Creative software and if so what and how to get it please?2) The Master knob on the breakout box just spins round and round without sto
ps.
In other words you can rotate it in either direction ad infinitum. Is this correct? Pushing it in and out does cause the mute to work fine. 3) The help file talks about an On Screen Display associated with the remote. I don't have one when I use the remote, even when I press the Display button. Again, do I need Creative software for the remote? I have a yellow question mark against Multimedia Audio Control in my device list. ThanksMessage Edited by Dunkelmann on 2-23-200607:22 PM
Message Edited by Dunkelmann on 2-23-200607:43 PM
Message Edited by Dunkelmann on 2-23-200608: PM
Message Edited by Dunkelmann on 2-23-200608:5 PM

Wow these forums still suck. You have easy questions and no one bothered to help you out. I registered jsut to answer them for you although you probably already figured it all out. . It seems that loudness is optomized by creatives own drivers. What you described was also true back when you could use the e-mu driver hacks before creative bought e-mu. 2. The master knob indeed spins for infinity, obviously with no effect once you get to either end. This sucks becasue i have OCD and constanly spin this thing all kinds of ways. THey should have used the same system as the line-/mic knob. Only God and the engineer will ever know why they did this. 3 Yes. The on screen display is pat of the creative media player app.
So to solve all your problems, you can get the full software package from creative.com under the support menu. Just follow the menu options for your device. The software requires that you have the hardware which you do so the software is free. One more problem you WILL have. The software doesnt install under XP. You have to enter windows safe mode and install it from there otherwise the whole thing freezes up during the start of the install process. Fun times!

Issue with fetching a record from IHPA table with PARNR value as condition

Hi All,
I am trying to fetch a particular record from IHPA table where i am giving the OBJNR number, PARVW and PARNR as customer no. , But I am not getting any record but if i will give OBJNR and PARVW it will generate a record with having same PARNR value.
Example :
case 1st :-
when i am passing following values in IHPA table,
OBJNR = IE000000000010070910
PRAVW = BP
PARNR = 620000562
it is not generating any record
case 2nd:-
But if i will pass
OBJNR = IE000000000010070910
PRAVW = BP
it will generate a record?(one row) which will include PARNR as same 620000562 along with other value.
Q1 - Why it's not generating in case 1st,
Q2 - How I will resolve this issue ? as i have to link some table as EQUI -
IHPA -
VCKUN
VCNUM ?
      I have written a code for this to join :
     SELECT A~EQUNR
       B~PARVW
       C~CCNUM
       D~CCNUM
       FROM EQUI AS A JOIN IHPA AS B ON AOBJNR = BOBJNR
       INNER JOIN VCKUN AS C ON BPARNR = CKUNNR
       INNER JOIN VCNUM AS D ON CCCNUM = DCCNUM
       APPENDING CORRESPONDING FIELDS OF TABLE IT_OBSO
       WHERE A~EQUNR IN S_EQN.
             AND PARVW = 'BP'.
      But it is not generating any record but when i am commenting the PARVW i am getting the mixed record of PARVW as (BP,SP,SH)
Let me know if any more clarification required.
Highly appreciate your help
Thanks & Regards
Shaw

Hi Santosh,
Thanks for your quick response.
But I am Sorry, I already checked with putting Zero before PARNR.
The issue is still as it is.
Thanks
Shaw

Recording audio from my pc speake

I just recently put a different sound card in my computer (Sound Blaster Li've 6) and now I can't seem to record streams or sounds off the internet like i was doing with my previous sound card. I was previously recording through the mix-record source on my old sound card but the sound card I have now doesn't have that so how do i record through the sound card I have now? The sources on my new sound card are Wave, TAD-In, Auxiliary, Microphone, Line-In, CD Audio, MIDI, CD Digital, and SPDIF-In. I tried all of them but none worked. Is it not possible with this sound card? Any help would be appreciated.

anybody?

HP Mini 110-1160SA problem recording sound from sound card

I am trying to record sound from the sound card itself rather than an external or internal microphone, using a free software called Sonarca Sound Recorder. For example, I play radio from the internet using the BBC Iplayer. I have Windows 7 Starter. When I use the Windows Control Panel > Hardware and Sound > Manage Audio Devices, I get a window called Sound. I press the Recording tab, and get a choice of Internal Microphone, External Microphone, and Stereo Mix. According to my sound recorder software's documentation, I need to select that Stereo Mix, because it means "record whatever the sound card is playing". However, the Stereo Mix recording device, despite having a red tick mark next to it is "Currently Unavailable". How do I make it available?

to be honest, i am not sure about your problems, normally, you need to set stereo mix as default device, then using recording devices to record sound on windows 7. Since you cannot make it, why not insall a virtual sound device, it works like a real one, install this streaming music recorder on your system, start recording. Just test it out by yourself.

Is " stereo mix" missing in your windows 7 on late 2009 imac 24 or 27 ?

I have a imac 27 running Windows 7 64bit and no stereo mix option.
I am a professor and when I do screen capture of scientific clips I need I can't get audio to record except by the imac mic from the speakers rather than directly.
That destroys the sound quality.
I have tried to download other sound card drivers and still no stereo mix recording or stereo mix playing options in sound!
I have the fairly useless digital audio s/pdif but not the stereo mix which is really needed in all kinds of recording applications.
I also downloaded the cirrus logic drivers shown in another thread for macbook users, but still no stereo mix.
Any idea for a fix?
This is an important basic function for any computer, and I can't understand why this is not supported yet?
Apple has used bootcamp to attract Windows users who want to use Windows natively. This is one of the most basic function, full audio capability.
This problem as well the cpu going 20 percent higher just plugging in a headphone, and the fact that the trrs headphone jack does not work on a trrs headset in windows 7 (including mic) is a real negative. The trrs headset like the iphone headset works fine with its mic in the mac side but not in windows side.
Drivers to make the basic hardware in an imac or macbook work in windows 7 shouldn't be rocket science. We need apple support or an innovative person out there to solve these problems.
If anyone reading this has the stereo mix on the w7 side, please let me know on this thread and maybe I can duplicate it on mine.
If not, we know this problem exists for every windows 7 bootcamp user.
Thanks!
Best to all
Dr. Duke

Generic, yes, but didn't take into account EFI64 (UEFI 2.x) req'd to native boot a 64-bit DVD of Vista SP1 or later. Apple has a list of those that are supported (actually, a list of UN-supported).
http://jowie.com/blog/post/2008/02/24/Select-CD-ROM-Boot-Type-prompt-while-tryin g-to-boot-from-Vista-x64-DVD-burnt-from-iso-file.aspx
A tutorial from MacBook Pro owner and 64-bit install:
http://deseloper.org/read/2009/05/windows-7rc-x64-with-boot-camp/
FAQ, Updates, etc http://www.apple.com/support/bootcamp
System Requirements: http://support.apple.com/kb/HT1899
Windows 7 FAQ: http://support.apple.com/kb/HT3986
List 64-bit Compatible: http://support.apple.com/kb/HT1846
Boot Camp 64-bit 3.1 http://support.apple.com/kb/DL979
Boot Camp Vista Upgrade Utility http://support.apple.com/kb/DL977
iMac (27-inch, Late 2009) displays a black screen during installation of Windows 7 using Boot Camp
http://support.apple.com/kb/TS3173
Windows7news: Fix for Vista Upgrade to 7 :
+Vista users who tried to perform an upgrade to Windows 7 were experiencing an error at exactly 62% of the update.+
Windows performed an automatic rollback to Windows Vista at this point leaving the user puzzled and confused. Some users even experienced an endless reboot problem which would initiate the upgrade process again only to fail again at 62%.
Vista user needs to click on the Fix-It button on the Microsoft support website after the upgrade failed at 62% to fix the issue and initiate the upgrade again.
http://support.microsoft.com/kb/975253

Recording on a track, while listening to another track...

Hi
Basically I currently have a blank track armed for recording with effects, and I have track 2 with an instrumental track. On the third track I have a song that I would like to listen to while recording, BUT not turn up in the recoding. Currently all 3 tracks turn up in the recording. I would only like track 1 and 2 to be in the final product. I need to listen to track 3 for reference.
Any help would be greatly appreciated.
I have Adition 3.0 with antares autotune installed on a PC, if this helps.
Thanks!

Hi Steve
Thanks so much for your reply. I am still a bit confused as to what exactly I have to do as this is really my first day using Adobe for my project.
Basically I have gone to the Windows mixer recording and I can verify that only the Mic that I am using is selected. That is good.
I have the audition mix to "always input" so I can hear what my recording is 'live'.
When you mention re routing things to inputs, would this be in the Adobe auditon program, or windows.
I would think that what I'm trying to do is very basic, which is setting the first track 'armed for record', which works fine (although I realize you said it will be dry until I 'save as an mp3' (i think))
the second track will be the 'instrumental track' which I would like to be in the final output without track 3
track 3 is the full song (with lyrics and instrument) which I just need for when I'm recording so I know when to say certain words and such..
the problem is, is when I go to record (with the mic), I am recording all 3 tracks, which is logical, but i only want my recording to end up having track 2 (instrumental) and track 1 (my mic) ....
is there no way I can simply select which tracks to end up in the recording on track 1?
also, track one I believe, once I've recorded, has all 3 tracks combined, which I only want to have track 1 and 2.
also, when i got to edit--> rewire setup, and click 'enable' ...it says I have no re wire programs on my computer....
maybe i have to select my track 3 for "read, write, touch, latch" settings (which are all currently set to 'read')?
sorry if I'm making things more complicated then they have to be...just need to get cracking on this asap....
thanks!

Dj mix recording

Similar Messages

Maybe you are looking for