Dladm does not show mac address for aggr
All,
When I run dladm show-aggr for my two aggr interfaces, I have one not displaying its MAC. Anyone a clue how I can get this sorted?
key: 2 (0x0002) policy: L2 address: 0:14:4f:da:13:e8 (auto)
device address speed duplex link state
nxge2 0:14:4f:da:13:e8 1000 Mbps full up attached
nxge3 <unknown> 1000 Mbps full up attachedCheers,
Davy
Edited by: Davy_S on Apr 18, 2009 1:52 AM
I had the same problem. SUN support recommends latest kernel patches. That solved my problem.
Similar Messages
-
Sh arp does not show mac address of IP --- ASA
Hi Everyone,
I can ping the IP from the ASA but when i do sh arp it does not show me mac address od that IP.
Need to know the reason behind this.
Regards
MAheshSo your ASA should have a route on the inside interface to internal networks. The address of that next hop in the routing table is the one you should have in your arp table allowing you to reach non-directly-connected (subnet-wise) hosts within the scope of that route statement.
Think through the logic - ASA pings a host. It needs to determine proper egress interface. It checks and asks "Is it reachable via a directly connected interface (most preferred route)?" Answer no. "Do I have a route statement telling me how to get to it?" Answer yes (otherwise use default). OK - so ASA sends packet out egress interface defined in that route statement to the next hop as defined in route statement and waits for reply. -
LDOM dladm does not show other interface.
Create another vnet1 on LDOM (ldg0). But dladm does not show it. There are entries in path-to-inst for it and I was able plumb interface.
bash-3.00# ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
vnet0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet 10.2.100.77 netmask ffffff00 broadcast 10.2.100.255
ether 0:14:4f:fb:32:a
vnet1: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 3
inet 192.168.30.30 netmask ffffff00 broadcast 192.168.30.255
ether 0:14:4f:fb:6c:99
bash-3.00# dladm show-dev
vnet0 link: unknown speed: 0 Mbps duplex: unknown
bash-3.00#
Yet dladm does not show device. What have I done wrong?
Here the ldm binding info for just networking
# ldm list-bindings primary (network only)
VSW
NAME MAC NET-DEV ID DEVICE LINKPROP DEFAULT-VLAN-ID PVID VID MTU MODE
primary-vsw0 00:14:4f:fb:1d:38 e1000g0 0 switch@0 1 1 1500
PEER MAC PVID VID MTU LINKPROP
vnet0@ldg0 00:14:4f:fb:32:0a 1 1500
vnet1@lqwest 00:14:4f:fb:b0:34 1 1500
vnet2@ldg0 00:14:4f:fb:6c:99 1 1500
# ldm list-bindings ldg0 (network only)
NETWORK
NAME SERVICE ID DEVICE MAC MODE PVID VID MTU LINKPROP
vnet0 primary-vsw0@primary 0 network@0 00:14:4f:fb:32:0a 1 1500
PEER MAC MODE PVID VID MTU LINKPROP
primary-vsw0@primary 00:14:4f:fb:1d:38 1 1500
vnet1@lqwest 00:14:4f:fb:b0:34 1 1500
vnet2@ldg0 00:14:4f:fb:6c:99 1 1500
NAME SERVICE ID DEVICE MAC MODE PVID VID MTU LINKPROP
vnet2 primary-vsw0@primary 1 network@1 00:14:4f:fb:6c:99 1 1500
PEER MAC MODE PVID VID MTU LINKPROP
primary-vsw0@primary 00:14:4f:fb:1d:38 1 1500
vnet0@ldg0 00:14:4f:fb:32:0a 1 1500
vnet1@lqwest 00:14:4f:fb:b0:34 1 1500
It appears to be working, but is this correct since dladm does not show the vnet1 interface?I had the same problem. SUN support recommends latest kernel patches. That solved my problem.
-
Express does not show IP address of wireless camera
I have a functioning Axis M1011 wireless camera, with a live stream into Safari on my local iMac. All is well.
My brand new Airport Express is definitely providing the wireless camera feed, as my internal airport card on my iMac is OFF.
What is odd is that Express does not show IP address of the wireless camera when you click on it in Airport Utility.
The iMac is static at 10.0.1.2. Express LAN IP is static at 10.0.1.1. The camera's wireless IP is static at 10.0.1.3.
I have a working, hidden network created by express.
I am baffled why express does not "report" the IP address of the camera that it definitely sees.
It does not report any wireless clients at all.
Any ideas?
Thanks.
macSo your ASA should have a route on the inside interface to internal networks. The address of that next hop in the routing table is the one you should have in your arp table allowing you to reach non-directly-connected (subnet-wise) hosts within the scope of that route statement.
Think through the logic - ASA pings a host. It needs to determine proper egress interface. It checks and asks "Is it reachable via a directly connected interface (most preferred route)?" Answer no. "Do I have a route statement telling me how to get to it?" Answer yes (otherwise use default). OK - so ASA sends packet out egress interface defined in that route statement to the next hop as defined in route statement and waits for reply. -
After upgrading to iOS 8 on my iPhone 5, the weather app does not show up results for any of the Indian States/cities. Can Apple look into this or does anyone have a solution to this.
Swipe from bottom of days listed ("Wednesday, Thursday, Friday, etc") upwards. I thought it was gone too but it's still there~just takes different way to access it.
-
safari does not show url address line anynore. google is taking up most of the space on the safari page
Hover the cursor over that line until it becomes a big plus sign with arrows on the left and right. Click and drag the cursor so that the rest of the address line is the way you want it.
(66963) -
Onlive TV listing does not show HD listing for series when I try to create a recording
It happened now already several times the the "Online TV Listing" does not show HD listing for series when I try to create a recording. Instead, it will show two series options in SD. Is this to make people use less bandwidth?
Here is what I am doing:
I go to this link https://www.verizon.com/fiostv/myservices/members/fiostv.aspx
Then to ...........DVR Manger
select ...........Record A Show
I type search e.g. Nathan for You
I click on ........Search
and I select ......Click here to Show Details
Then I get to chose from 2 (the same) SD channels.
Nathan for You
190 Comedy Central
Tue, Jul 29 10:30 PM
Record Show Record Series
Nathan for You
190 Comedy Central
Tue, Aug 05 10:30 PM
Record Show Record Series
But there is the same on channel 690 HD!
This happens not only to this particular channel!
I remember it used to show also the HD channels.
The only way to schedule in HD is to find the listing in the TV schedule, at the right time and there you will get the
correct choices for both SD & HD.
Can this be fixed?
Thanks!On the right click on HD under video quality to filter it.
-
RE1000 - Does not filter MAC ADDRESS
I bought this to extend the range of my new Linksys 3200, thinking that they would be compatible. Silly me! After spending 3 plus hours screwing around with this, I got online and happened to stumble on a post from another user, that stated that this device DOES NOT FILTER MAC ADDRESSES! So, if you want to use mac filtering you can't use this! Ridiculous! Some basic instructions to inform users of this fact would be helpful. But it comes with no manual or instructions whatsoever. Save your money.
I have a E2500 router, I was adding the Extender because of the size of the office. I set my router up to "Permit only" Mac IDs', right there I should have questioned why nothing worked. The Package & the base of the unit both had a matching MAC ID - to bad that the unit had a different one. I don't remember how much time I spent but finally disable the MAC ID Filter on the router and got the real one. From that point on, everything worked, I even was able to setup with the router internal security switch. Just think how a little thing like an ID would make an IT Guy just a little more mis-trustful, not count the grey hair.
-
ARP table not populating mac address for previously reachable IP address
Router has been online and working fine with one BGP neighbor for almost 2 years and no downtime. 2 weeks ago, added a 2nd BGP peer. Everything worked fine for 2 weeks, then all of a sudden yesterday the 2nd BGP peer is disconnected and does not come back. ISP checks and sees everything looks fine on their end. We cannot even ping each other now.
Upon investigation, the ARP table is not even populating the MAC address for the BGP peer IP anymore (same local subnet). Stays "incomplete" in the table no matter what we do, including clearing arp table, changing IP address, etc.
Plug a laptop directly into the 2nd BGP peer FE port and replicate the IP addressing. Laptop cannot ping Router, but Router CAN ping laptop. Check ARP table, but STILL no mac address assigned and now not even the ARP table showing "incomplete".
Thinking it could be the FE interface, switch to the 2nd FE interface and perform same laptop test, this time with arbitrary IP addressing. Now cannot ping each other, no MAC in ARP table.
End up rebooting the router and lo-and-behold, everything is working normally again. 2nd BGP peer peers up instantly.
I should also mention that the 1st BGP peer worked flawlessly throughout, taking all the Internet load and having no issues throughout.
Also, the FE ports for the 2nd BGP peer are on an HWIC FE card plugged into the router. The 1st BGP peer is plugged into the built-in GE interface. 2901 running: c2900-universalk9-mz.SPA.151-4.M4.bin
Lastly, no router resource issues, no error messages, no logs. Just the BGP peer disconnecting.
I have never, in 20 years working with Cisco routers seen something like this before. This is the most fundamental aspect of IP and Ethernet that was not working.
Has anyone ever seen this behavior before??
Here is the router config (IP's changed):
version 15.1
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
service internal
service sequence-numbers
boot-start-marker
boot-end-marker
logging buffered 150000
aaa new-model
aaa authentication login LAUTHEN local
aaa authentication login TAUTHEN local group tacacs+ enable
aaa authorization console
aaa authorization exec LAUTHOR local if-authenticated
aaa authorization exec TAUTHOR local group tacacs+ if-authenticated
aaa session-id common
clock timezone PST -8 0
clock summer-time PDT recurring
no ipv6 cef
no ip source-route
ip cef
no ip domain lookup
multilink bundle-name authenticated
username ubiadmin privilege 15 secret 4 .JbeuWXuZvchrG0OL.5BftFtqrrEyxcnVHn5rIuCnTk
username umitsnoc01 privilege 15 secret 4 cUmoRUjey9O1x.wk9S.kleX.iAAhCwihupr6Z98p6OA
redundancy
ip ssh version 2
track 1 interface GigabitEthernet0/0 line-protocol
class-map match-any AutoQoS-VoIP-RTP-Trust
match access-group name SIP-Media-INBOUND
class-map match-any AutoQoS-VoIP-Control-Trust
match ip dscp cs3
match ip dscp af31
class-map match-any Customer-Voice
match access-group name Customer-VPNs
class-map match-any media
match access-group name SIP-Media
class-map match-any signaling
match access-group name SIP-Signaling
policy-map AutoQoS-Policy-Trust
class AutoQoS-VoIP-RTP-Trust
priority percent 70
class AutoQoS-VoIP-Control-Trust
bandwidth percent 5
class class-default
fair-queue
policy-map queue
class signaling
bandwidth percent 5
class media
priority percent 50
class Customer-Voice
priority percent 40
class class-default
fair-queue
policy-map shape
class class-default
shape average 10000000
service-policy queue
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
description BGP Peer 1
ip address 2.2.2.2 255.255.255.252
no ip redirects
ip flow ingress
ip flow egress
duplex auto
speed auto
service-policy output shape
interface GigabitEthernet0/1
description LAN
ip address 1.2.3.4 255.255.255.0
no ip redirects
ip flow ingress
ip flow egress
standby 255 ip 1.2.3.1
standby 255 priority 105
standby 255 preempt
standby 255 mac-address 1a2b.3c4d.5e6f
standby 255 track 1 decrement 10
duplex auto
speed auto
service-policy output AutoQoS-Policy-Trust
interface FastEthernet0/0/0
description BGP Peer 2
ip address 1.1.1.1 255.255.255.252
ip flow ingress
ip flow egress
duplex full
speed 100
service-policy output shape
interface FastEthernet0/0/1
no ip address
shutdown
duplex auto
speed auto
router bgp 7777
bgp router-id 2.2.2.2
bgp log-neighbor-changes
network 1.2.3.0 mask 255.255.255.0
neighbor 1.1.1.2 remote-as 5555
neighbor 1.1.1.2 update-source FastEthernet0/0/0
neighbor 1.1.1.2 prefix-list L3-DEFGW in
neighbor 1.1.1.2 route-map L3-LPREF-IN in
neighbor 2.2.2.1 remote-as 6666
neighbor 2.2.2.1 ebgp-multihop 2
neighbor 2.2.2.1 update-source GigabitEthernet0/0
neighbor 2.2.2.1 send-community
neighbor 2.2.2.1 prefix-list COLO-DEFGW in
neighbor 2.2.2.1 route-map COLO-LPREF-IN in
neighbor 2.2.2.1 route-map COLO-OUT out
ip forward-protocol nd
ip bgp-community new-format
ip as-path access-list 5 permit _5555_
ip as-path access-list 5 deny .*
ip as-path access-list 10 permit ^6666$
no ip http server
no ip http secure-server
ip flow-top-talkers
top 50
sort-by bytes
ip route 0.0.0.0 0.0.0.0 1.1.1.2 254 name L3
ip route 0.0.0.0 0.0.0.0 2.2.2.1 255 name COLO1
ip route 10.0.0.0 255.0.0.0 10.10.10.10 name FW_OUTSIDE
ip tacacs source-interface GigabitEthernet0/1
ip access-list standard SNMP_SOURCES
permit 12.12.12.0 0.0.0.255
deny any log
ip prefix-list L3-DEFGW seq 5 permit 0.0.0.0/0
ip prefix-list COLO-DEFGW seq 5 permit 0.0.0.0/0
ip prefix-list COLO-LPREF-OUT seq 5 permit 1.2.3.0/24
route-map COLO-LPREF-IN permit 5
match as-path 5
set local-preference 250
route-map COLO-LPREF-IN permit 10
set local-preference 150
route-map COLO-LPREF-IN permit 20
route-map COLO-OUT permit 10
match ip address prefix-list COLO-LPREF-OUT
set as-path prepend 7777 7777 7777
set community 29795:1004
route-map COLO-OUT permit 20
route-map L3-LPREF-IN permit 10
match as-path 10
set local-preference 200
route-map L3-LPREF-IN permit 20
set local-preference 150
snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
snmp-server enable traps vrrp
snmp-server enable traps flowmon
snmp-server enable traps transceiver all
snmp-server enable traps ds1
snmp-server enable traps call-home message-send-fail server-fail
snmp-server enable traps tty
snmp-server enable traps license
snmp-server enable traps envmon
snmp-server enable traps ethernet cfm cc mep-up mep-down cross-connect loop config
snmp-server enable traps ethernet cfm crosscheck mep-missing mep-unknown service-up
snmp-server enable traps flash insertion removal
snmp-server enable traps mac-notification
snmp-server enable traps aaa_server
snmp-server enable traps cef resource-failure peer-state-change peer-fib-state-change inconsistency
snmp-server enable traps memory bufferpeak
snmp-server enable traps config-copy
snmp-server enable traps config
snmp-server enable traps config-ctid
snmp-server enable traps event-manager
snmp-server enable traps hsrp
snmp-server enable traps cpu threshold
snmp-server enable traps rsvp
snmp-server enable traps syslog
snmp-server enable traps vtp
snmp-server enable traps ipslaWhen you were checking the ARP table was there an entry for Fast0/0/0?
HTH
Rick -
Aperture does not show tick box for shared photo stream as promised on the help screen
I try to configure Aperture for iCloud shared Photo Stream. According to the help screen, I should select Preferences and see a panel with 4 tickboxes. The first three relate to My Photostream and work fine on all my devices. The crucial fourth tick box for sharing with others however does not show however. What else should I set-up to see the 4th tick box ?
You need:
'A Mac with OS X v10.8.2 or later and iPhoto 9.4 or later or Aperture 3.4 or later'
http://help.apple.com/icloud/#mmbc402b84 -
:: NWA does not show table view for monitoring reports ::
Hi,
We are facing an issue in one of our portal system.
I click on Portal index page, then I go to Net weaver Administrator --> Monitoring --> Java system reports.
Here I get the resource utilization graphs.
The graphs show proper values however when I click on table view it does not show any value or table at all.
Then I click on Settings button, and click on Persistent radio button.
It asks to enter the number of days for which the the data should be stored.
I gave it as 2 days and click on Apply button.
It shows a message saying "changes would be effective after restarting monitoring service".
However when I go there i.e. NWA --> Administration --> Applications
I get below services
cafruntimemonitoring~ear
com.sap.ip.bi.sdk.monitoring
tclmwebadminmonitoravail~wd
tclmwebadminmonitorcomplib~wd
tclmwebadminmonitorprovider_ear
tclmwebadminmonitorstate~wd
tclmwebadminoverviewmonitoring~wd
tcmonitoringsysteminfo
Would you kindly suggest which service from above list should be restarted ?
Thank you, Regards,
Girish Garje.I think what is being asked is "How do I expose a database view as a schema table in Configuration Manager?"
This is accomplished by creating a database view within the WCC database schema (and with the WCC schema user as the view owner). The view then will appear as a table in the "table" tab in Configuration Manager.
One caveat in 11g is that the user created by RCU does not have any privileges to read/create views in its own schema. You may need to grant privileges to views for the WCC schema user before this will work. -
Search Item drop-down does not show any data for Advanced Search.
Hi,
I have a requirement to add a new criteria to the existing Advanced Search region of 'My Employee Information' in Manager Self Service responsibility. I substituted the AdvancedSearchVO to include the new column. Using personalization i did the below steps to show the new column in the page,
1) Created a 'Message Styled Text' item under Table Layout region to display the result. I associated the View Instance (AdvancedSearchVO1) and View Attribute (AttrColumn).
2) In Advanced Search Panel created a new CriteriaRow and set the 'Search Allowed' property to True.
3) In Advanced Search Mappings i tried to create the new mapping but the Search Item drop-down does not show any of the CriteriaRow item. But Results Item shows the 'Message Styled Text' item created in step 1 above.
Any idea what i would be missing becasue of which 'Search Item' property does not show any data?
I am using OAF version 12.1.1.
Thanks, SureshHi,
I faced the same situation but i still waiting for the solution.. this is my problem's thread..
Addition of LOV Search Filter using Personalization
But when i tried to create a new custom page with advanced table and created a new LOV column via personalization. i was able to create new search mapping.. but this is not happening in the seeded page case :(.
I m also looking for solution...if any one can provide some inputs on it , will be highly appreciated.
Thanks
Renu -
Help- Elements 9 "Does not show Advanced dialog" for downloading
Hi, I'm fairly new to elements and have gone through my "Dummies Book" and yesterday received my Elements 9 book by Scott Kelby and Matt Kloskowski. My problem is when I'm attempting to download 5 new pictures from a card that still has 700 on it - The download organizer does NOT show the "Advanced Dialog button" on the bottom-left corner of the dialog box which as Kelby and Kloskowski indicate, would allow me to select only the 5 new pictures that I am attempting to download.
Can anyone assist? Do you have any recommendations? It is clearly described (even with pictures) in the Scott Kelby book; however, my screen does not list the advanced dialog button.
Thank you-Thank you-Thank you!Bob, It just seems that using windows to import into a file and then
importing from Files and Folders is a workaround to not being able to bring
up the Advanced Dialog Button. I do appreciate and thank you for this
suggestion!
Overall, I'm disappointed in the Photoshop Elements 9 program. It appears
from reading this forum, that there are many similar difficulties with the
Advanced Dialog Button and other similar programming elements that have
perpetuated from Elements 8.
Again, thank you for your time and interest and support in this forum.
Without contributors like yourself, many "newbies" would be forever lost.
One last question, Since I've downloaded by original batch of 700 photos
three times now, what would be the easiest way of cleaning up my mess??????
Thank you. Hoping to be able to use this program by Christmas!!!!! -
How do I determine the size of an event (cmd I does not show any size for events).
How do I determine the size of an Event in iPhoto? (Cmd + I does not show size information at the event level).
If you're running iPhoto 8 (09) select the event and look at the Info pane at the lower left hand corner of the window. It will give you the number of photos and size:
for iPhoto 9 (11) open the Event, select all of the photos in it and open the Info drawer at the right by typing Command+i. The number of photos and size will be at the top of the Info drawer.
OT -
Crystal Report does not show the webelement for SAP System
Hi all,
I have added web element in Crystal report for SAP system (BI or R/3) . But it does not show the control. It shows only scipt.It does not render the HTML.
But if I add the webelement for Excel sheet ,It shows the control.
How can I add web element for SAP System? Can't we use web controls in SAP system ?
Help me in this regard.
Regards
Hemalatha JHi,
We have the same problem, did you find the final solution?
Thanks in advance
Regards.
Maybe you are looking for
-
On Illustrator CC, somehow the wheel of the mouse doesn't do the scrolling right.
When I scroll down it works, when I scroll up, it scrolls down. This happens only on Illustrator, not on Photoshop.
-
Exporting an album with stills and video as a Quicktime movie in iPhoto 8.1.2
Hello, Running iPhoto 8.1.2 here. We have created an album that contains still images (~300) and several videos. All of the videos were taken on a iPhone then we imported them to iPhoto. Videos are interspersed between the photos. We need to export t
-
Sorry to ask what is probably a pretty amateurish question, but how do you configure two usb mics to function as 2 different inputs? Both mics are recognized and work individually, but when I plug them in only one functions properly. Thanks in advanc
-
ABAP Program Name CHanging the PSA Load status
Hi, Our Scenario is Non-SAP -> PI -> BI. Every Day PI reads the file from source and it will directly upload to PSA in BI.But in PSA the status will show as yellow only it is not turning to green.But I am able to see the data in PSA but status is yel
-
Macbook Air 13inch for Graphic / Web Design ?
Hi guys, I decided to come here to ask for some expert help if i should buy the macbook air or pro. But before that, let me tell you what I usually do. I use Adobe Fireworks as my primary design tool for web graphics / screen graphics, maybe use Phot