Dll soes not work after restart teststand

Hi NI Team,
I have an issue whereby i am using a 3rd part dll to program a device. At 1st it is able to program correctly using the designated dll. But after i've restart the teststand, it still able to point to the dll, but seems like the dll is not working as it should be. In order to make it work again, I need to change the dll path to another location in order to make it work.
I've attached the following
Sequence.jpg
- Shows the module configuration
return_result.jpg
- Shows the return result of a weird return as the suppose return result suppose to be "1" or "0"
Please do advice. Thanks
Attachments:
Sequence.JPG ‏190 KB
return_result.JPG ‏21 KB

Hi There - Thanks for the reply,
The problem i am facing is the dll that i am using does not work as it should after restart teststand, unless i change the path or point the dll to another new path. The error that i am getting is, the return result shows that it can't open the file path that that has been defined in the dll call path name parameter. The weird thing is, the dll able to work (able to point to the right image again ) after i point the dll to another path, meaning if i create a new folder then dump in the same dll inside the folder and point the dll to new folder it able to work. But i will see the same problem again after i restart teststand. In terms of unloading the dll, i have tried the run options to unload module either after step end or sequence end. But the problem still exists.....

Similar Messages

PCI wireless card does not work after restart - FM2-A55M-E33

Installed TP-LINK WN751ND wireless PCI card onto FM2-A55M-E33 motherboard. The card works fine after cold start, but does not work after restart. Windows recognises the card, but it gets code 10, cannot start.
BIOS is updated (v.11.1), as well as drivers and Windows 7 64.
I suspect that this might be the issue: Incorrect ASPM Transitions on the GPP Interface as found in ChipsetMotherboard_TechDocs/48671.pdf on AMD's official support site.
Does anyone know more about this issue?

Great! I've done that and now my card shows up. Thing is, when I try to get an IP address, it won't work. Here is the command output:
ieee80211 phy0: wl_ops_config: change monitor mode: false (implement)
ieee80211 phy0: wl_ops_config: change power-save mode: false (implement)
ieee80211 phy0: wl_ops_bss_info_changed: qos enabled: false (implement)
And then it times out and no IP is assigned. The thing is, wpa_supplicant stays alive after this time out, and I am unable to kill it (killall -9 wpa_supplicant won't kill it). At this point if I try to reboot the machine, it will stop at 'Rebooting' and won't go anywhere. If I turn off the wireless card in its switch Linux crashes. If I try to get an ip again (by running dhcpcd) the command will hang and not return to the shell anymore.
I am unable to find any useful information in the logs.
Got any more suggestions?
Thanks! (And sorry to disturb so much)

Changed Password Not working after restart[What to do]

Recently I've changed my password, but it's not working after restart.
I've noticed that, input option is not taking one of the password characters which is '!'.
I've the recovery disks, system accepts my fingerprint too.
Any help will be highly appreciated.
Thanks.

Hello,
Let me explain you what happened.
One evening I was trying to open my ThinkPad. Usually it asks for
fingerprint or password(I'm not sure which password, power-on/hard
drive). But this time I failed using my finger. and I tried with
password, but could not recall.
Then I restart and again tried with finger, this time it worked. Now
after login in Windows XP I removed all old fingerprints and create
few new. When I create new, it was asking for password, or new
password to replace. As I could not recall the pass, I've given new
password to replace.
Now to check I gave a restart. Fingerprint accepted for Power-on but
also asking for password again(Now I can see it's for Hard Drive). I
tried with new password. But it's not working. And even not taking one
character ('!') of the password.
Now can you tell me, if I did change password for Hard Drive in the
last description. Or is that possible to change it from Windows XP
environment. Else it's possible that the Hard Drive password remain as
it was which has been set from ThinkVantage before OS boot. Let me
know if you've any query which I've missed.
Thanks.

Microphone does not work after restarting computer

I just received the Creative Xmod soundcard yesterday after using an Icemat siberia usb headset sound card for a couple months. The sound is a lot better with the creative soundcard however, if I restart my computer and go back into ventrilo, my microphone does not work. It doesnt make any sound when I talk into it (almost as if it muted itself) but it hasnt. I check my sound settings and everything is the way it should be.....but the mic isnt producing any sound. It is not my headphones that is causing the problem because I have never had this problem with my old icemat soundcard. I am currently using :
Sennheiser PC350 headset
Windows XP Home Edition
The newest version of Ventrilo

http://picsend.net/images/240403ventsetup.JPG
That is how I have ventrilo setup. A friend of mine said I should Mux set to Record Control, but it only gives me the option for Wave In =/

Printer does not working after restart

I have installed HP LaserJet m1120 using hplip and hplip-plugin from AUR.
Everything was fine (printer worked) but after rebooting, printer doesn't working at all - cups doesn't "see" it and hp-testpage shows this:
# hp-testpage -i
warning: hp-testpage should not be run as root/superuser.
HP Linux Imaging and Printing System (ver. 3.12.10a)
Testpage Print Utility ver. 6.0
Copyright (c) 2001-14 Hewlett-Packard Development Company, LP
This software comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to distribute it
under certain conditions. See COPYING file for more details.
| SELECT PRINTER |
Num CUPS Printer
0 HP_LaserJet_M1120_MFP
1 PhotoPrint
Enter number 0...1 for printer (q=quit) ?0
error: Unable to communicate with device (code=12): hp:/usb/HP_LaserJet_M1120_MFP?serial=MF12D9K
error: Unable to print to printer. Please check device and try again.
note: If an error occured, or the test page failed to print, refer to the HPLIP website
note: at: http://hplip.sourceforge.net for troubleshooting and support.
PhotoPrint is my second printer and it works fine.
What should i do? I have been trying to configure it for long time...
Last edited by Extravert (2012-11-17 14:46:06)

Maybe, I haven't understood something but it still does not working.
I found that journalctl outputs some errors
Nov 17 22:57:06 trash-serv hp[405]: io/hpmud/pp.c 627: unable to read device-id ret=-1
Nov 17 22:57:06 trash-serv python2[406]: io/hpmud/pp.c 627: unable to read device-id ret=-1
And lsusb does not shows this printer
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Last edited by Extravert (2012-11-17 15:17:13)

Firefox is not working after restart. Need to reinstall every time I am starting PC.

Hello everyone,
I was happily using Firefox untill few days ago. Since then Firefox takes about five minutes to start (you cant see in taskbar or Application in task manager, just in Processes in task manager). When it finaly opens the first window it is not responding and there just blank window). It does the same in safe mode.
I tried to reinstall it several time, with deleting every Firefox related files on computer (following every relevant instruction from Support). I tried to backup my profile and start with new one after reinstall. Every time with same result: Firefox works perfectly after reinstall (even when I transfer files from old profile, every bookmark is right), but when I restart computer the problem is back.
I checked PC for malware and viruses by Avast, there should be now collision with other software since I did not install anything recently. I have cleaned registres, cache and cookies with CCleaner.
I am running 64-bit Windows 7 Lenovo E430, everything worked perfectly for half a year. Only problem I can relate to is a warning message about low free space on system drive, which occured at the same time problems with Firefox started (but it is now even true, I have 5 GB of free space on system drive).
I found other unresolved topics, one of them with same system configuration as mine.
https://support.mozilla.org/en-US/questions/956861?esab=a&as=aaq
https://support.mozilla.org/cs/questions/958824
Any suggestions before I desperately change to Firefox Portable?

Why not install and try Firefox portable, it may well be a good troubleshooting step. Try running it from an external memory stick.
The threads you referred to
* [/questions/956861] was closed but never solved
*[/questions/958824] similar
Some system information would help
*How much RAM is installed ?
*What is the total size of the Hard Disk Drive ?
*What is the current amount of free-space in GB ? and as a percentage ?
I try not to use Windows but certainly at one stage a rule of thumb was 20-25% free space should be available. Under about 12% defragging of a disk would likely fail. A page file would need to be larger than the amount of RAM maybe 1.5X , and a hibernate file would be the size of the RAM.
* Do not Hibernate if you are low on HDD space.
I suggest you proceed as follows
#Answer the above questions. I worry you have a lack of diskspace.
#Do a full scan with multiple and up-to-date anti-malware tools. Do not rely on Avast alone. No tool picks up everything. Report back what you scanned with and what was found.
#Backup and keep whatever profiles may be good or may contain recent information such as passwords and bookmarks, but do not use them yet.
#Download a new installer then Do a clean reinstall of Firefox, ensuring that the program folders are deleted before you re-install.
#Now restart, you expect the first restart to work. Close down and try again does it now work OK ?
The detailed instructions in the thread you read [/questions/958824#answer-436552] should help you.
If you have continuing problems is this after a restart of Firefox, or a restart of the Windows Operating System ?

EM not working after restart

I have an inherited installation of OEM that I cannot get to work. By which I mean I get a "503 Service Unavailable Service is not initialized correctly. Verify that the repository connection information provided is correct" error in my browser. This might have been caused when I tried to change the sysman password. I think OEM was still running after the pw change, but after a database restart (application of Oracle patch) it has stayed broken.
I have only been working with Oracle for a few months, I do not depend on OEM for a lot but I need to get OEM working again. I have googled for answers and read documentation, but I am missing something and I am hoping one of you all will know what it is.
OEM version: 11.2.0.1.0 (agent) Oracle Enterprise Manager 10g Release 5 Grid Control (oms)
database version: 11.2.0.1.0
I have seem to have three oracle homes:
db & listener: /u01/db/oracle/product/11.2.0/dbhome_1
agent: /u01/app/oracle/agent10g
oms: /u01/app/oracle/oms10g
OS: linux
I have attempted several times to drop and create the repository but end up with the same errors. I don't think the drops and creates have been successful though, because of errors during the process and becuase the sysman user keeps getting locked.
The repository errors look like these:
May 24, 2011 4:23:14 PM oracle.sysman.emcp.EMConfig perform
INFO: This operation is being logged at /u01/db/oracle/cfgtoollogs/emca/sid01/emca_2011_05_24_16_22_01.log.
May 24, 2011 4:23:15 PM oracle.sysman.emcp.util.DBControlUtil stopOMS
INFO: Stopping Database Control (this may take a while) ...
May 24, 2011 4:23:36 PM oracle.sysman.emcp.EMReposConfig createRepository
INFO: Creating the EM repository (this may take a while) ...
May 24, 2011 4:23:36 PM oracle.sysman.emcp.EMReposConfig invoke
SEVERE: Error creating the repository
May 24, 2011 4:23:36 PM oracle.sysman.emcp.EMReposConfig invoke
INFO: Refer to the log file at /u01/db/oracle/cfgtoollogs/emca/sid01/emca_repos_create_<date>.log for more details.
May 24, 2011 4:23:36 PM oracle.sysman.emcp.EMConfig perform
SEVERE: Error creating the repository
Refer to the log file at /u01/db/oracle/cfgtoollogs/emca/sid01/emca_2011_05_24_16_22_01.log for more details.
Could not complete the configuration. Refer to the log file at /u01/db/oracle/cfgtoollogs/emca/sid01/emca_2011_05_24_16_22_01.log for more details.Edited by: user13716631 on May 25, 2011 2:14 PM

Hi Vishal,
Here are the most recent logs with errors:
emoms.log - these errors repeat over and over
2011-05-26 08:46:10,126 [ApplicationServerThread-16] ERROR app.SessionObjectManager sessionDestroyed.128 - java.sql.SQLException: ORA-28000: the account is locked
java.sql.SQLException: ORA-28000: the account is locked
        at oracle.jdbc.driver.DatabaseError.throwSqlException(DatabaseError.java:137)
        at oracle.jdbc.driver.T4CTTIoer.processError(T4CTTIoer.java:315)
        at oracle.jdbc.driver.T4CTTIoer.processError(T4CTTIoer.java:276)
        at oracle.jdbc.driver.T4CTTIoer.processError(T4CTTIoer.java:271)
        at oracle.jdbc.driver.T4CTTIoauthenticate.receiveOauth(T4CTTIoauthenticate.java:646)
        at oracle.jdbc.driver.T4CConnection.logon(T4CConnection.java:307)
        at oracle.jdbc.driver.PhysicalConnection.<init>(PhysicalConnection.java:429)
        at oracle.jdbc.driver.T4CConnection.<init>(T4CConnection.java:150)
        at oracle.jdbc.driver.T4CDriverExtension.getConnection(T4CDriverExtension.java:31)
        at oracle.jdbc.driver.OracleDriver.connect(OracleDriver.java:608)
        at oracle.jdbc.pool.OracleDataSource.getConnection(OracleDataSource.java:217)
        at oracle.jdbc.pool.OracleConnectionPoolDataSource.getPhysicalConnection(OracleConnectionPoolDataSource.java:113)
        at oracle.jdbc.pool.OracleConnectionPoolDataSource.getPooledConnection(OracleConnectionPoolDataSource.java:76)
        at oracle.jdbc.pool.OracleImplicitConnectionCache.makeCacheConnection(OracleImplicitConnectionCache.java:1361)
        at oracle.jdbc.pool.OracleImplicitConnectionCache.getCacheConnection(OracleImplicitConnectionCache.java:440)
        at oracle.jdbc.pool.OracleImplicitConnectionCache.getConnection(OracleImplicitConnectionCache.java:335)
        at oracle.jdbc.pool.OracleDataSource.getConnection(OracleDataSource.java:285)
        at oracle.jdbc.pool.OracleDataSource.getConnection(OracleDataSource.java:253)
        at oracle.sysman.util.jdbc.ConnectionCache._getConnection(ConnectionCache.java:336)
        at oracle.sysman.util.jdbc.ConnectionCache._getConnection(ConnectionCache.java:322)
        at oracle.sysman.util.jdbc.ConnectionCache.getUnwrappedConnection(ConnectionCache.java:575)
        at oracle.sysman.emSDK.svc.conn.FGAConnectionCache.getFGAConnection(FGAConnectionCache.java:218)
        at oracle.sysman.emSDK.svc.conn.ConnectionService.getPrivateConnection(ConnectionService.java:1158)
        at oracle.sysman.emSDK.svc.conn.ConnectionService.getPrivateConnection(ConnectionService.java:1192)
        at oracle.sysman.eml.app.SessionObjectManager.sessionDestroyed(SessionObjectManager.java:116)
        at oracle.sysman.eml.app.SessionListener.sessionDestroyed(SessionListener.java:114)
        at com.evermind.server.http.HttpApplication.invalidateSession(HttpApplication.java:683)
        at com.evermind.server.http.EvermindHttpSession.invalidate(EvermindHttpSession.java:272)
        at com.evermind.server.http.SessionAsyncInvalidateHandler.invalidateSession(SessionAsyncInvalidateHandler.java:173)
        at com.evermind.server.http.SessionAsyncInvalidateHandler.run(SessionAsyncInvalidateHandler.java:133)
        at com.evermind.util.ReleasableResourcePooledExecutor$MyWorker.run(ReleasableResourcePooledExecutor.java:192)
        at java.lang.Thread.run(Thread.java:534)
2011-05-26 08:46:13,759 [AJPRequestHandler-ApplicationServerThread-11] ERROR conn.ConnectionService verifyRepositoryEx.911 - Invalid Connection Pool. ERROR = ORA-28000: the account is locked
2011-05-26 08:46:23,837 [AJPRequestHandler-ApplicationServerThread-5] ERROR conn.ConnectionService verifyRepositoryEx.911 - Invalid Connection Pool. ERROR = ORA-28000: the account is locked
2011-05-26 08:46:25,068 [AJPRequestHandler-ApplicationServerThread-10] ERROR conn.ConnectionService verifyRepositoryEx.911 - Invalid Connection Pool. ERROR = ORA-28000: the account is locked
2011-05-26 08:46:27,676 [AJPRequestHandler-ApplicationServerThread-15] ERROR conn.ConnectionService verifyRepositoryEx.911 - Invalid Connection Pool. ERROR = ORA-28000: the account is locked
2011-05-26 08:46:33,368 [AJPRequestHandler-ApplicationServerThread-10] ERROR conn.ConnectionService verifyRepositoryEx.911 - Invalid Connection Pool. ERROR = ORA-28000: the account is locked
2011-05-26 08:46:35,561 [AJPRequestHandler-ApplicationServerThread-7] ERROR conn.ConnectionService verifyRepositoryEx.911 - Invalid Connection Pool. ERROR = ORA-28000: the account is locked
2011-05-26 08:46:36,588 [AJPRequestHandler-ApplicationServerThread-6] ERROR conn.ConnectionService verifyRepositoryEx.911 - Invalid Connection Pool. ERROR = ORA-28000: the account is locked
2011-05-26 08:46:37,933 [AJPRequestHandler-ApplicationServerThread-12] ERROR conn.ConnectionService verifyRepositoryEx.911 - Invalid Connection Pool. ERROR = ORA-28000: the account is locked
2011-05-26 08:46:41,041 [ApplicationServerThread-16] ERROR app.SessionObjectManager sessionDestroyed.128 - java.sql.SQLException: ORA-28000: the account is lockedemdctl.trc
2011-05-02 11:03:31 Thread-4138851088 ERROR http: 6: snmehl_read: error on read: Connection reset by peer (error = 104)
2011-05-02 11:03:32 Thread-4138253072 WARN http: snmehl_connect: connect failed to (server01.something.com:1157): Connection refused (error = 111)
2011-05-02 11:03:32 Thread-4138457872 WARN http: snmehl_connect: connect failed to (server01.something.com:1156): Connection refused (error = 111)
2011-05-09 13:14:44 Thread-4138048272 WARN http: snmehl_connect: connect failed to (server01.something.com:1156): Connection refused (error = 111)
2011-05-09 13:15:03 Thread-4138470160 WARN http: snmehl_connect: connect failed to (server01.something.com:1157): Connection refused (error = 111)
2011-05-09 13:20:24 Thread-4138756880 WARN http: snmehl_connect: connect failed to (server01.something.com:1157): Connection refused (error = 111)
2011-05-09 13:23:46 Thread-4138195728 WARN http: snmehl_connect: connect failed to (server01.something.com:1156): Connection refused (error = 111)
2011-05-10 16:39:19 Thread-4138027792 WARN http: snmehl_connect: connect failed to (server01.something.com:1157): Connection refused (error = 111)
2011-05-10 16:43:15 Thread-4138162960 WARN http: snmehl_connect: connect failed to (server01.something.com:1157): Connection refused (error = 111)
2011-05-10 16:54:23 Thread-4138691344 WARN http: snmehl_connect: connect failed to (server01.something.com:1157): Connection refused (error = 111)
2011-05-25 13:19:12 Thread-4138584848 WARN http: snmehl_connect: connect failed to (server01.something.com:1157): Connection refused (error = 111)
2011-05-25 15:06:51 Thread-4138253072 WARN http: snmehl_connect: connect failed to (server01.something.com:1157): Connection refused (error = 111)
2011-05-25 15:10:25 Thread-4138466064 WARN http: snmehl_connect: connect failed to (server01.something.com:1157): Connection refused (error = 111)
2011-05-25 15:11:15 Thread-4138810128 WARN http: snmehl_connect: connect failed to (server01.something.com:1157): Connection refused (error = 111)
2011-05-25 15:13:37 Thread-4138064656 WARN http: snmehl_connect: connect failed to (server01.something.com:1157): Connection refused (error = 111)Thanks for your response

Passwords not working after restart

After the server is restarted users can't login until the password is reset. I have a few generic accounts that are not affected. All passwords are Open Directory. Was going to try Crypt password to see if the issue persists. I have turned off the ability to change passwords on all accounts. The solution I had been given was to change the admin passwords. I did that. It still doesn't matter. I could change an account password. Login. Restart the server and not be able to login till the password has been reset in Workgroup manager. The server is 10.4.6 and this seems to have been happening since 10.4.2.
iMacG4 Mac OS X (10.4.5)

It is possible for the Password Server's SASL realm to change across restarts if the hostname has never been set explicitly. The default realm, if none is set, is hostname. However, depending on the order things get launched at boot, hostname may return the Bonjour name instead of the DNS name. For SASL purposes, it does not matter what the realm name is, but it must be the same all the time. It's the uncertainty that causes the problem. You can set the value for the SASL realm with the "mkpassdb -setrealm" command. After setting the realm, type, "killall PasswordService" to restart the daemon. The two SASL realm values to try are 1. whatever is returned by 'hostname' and 2. "localhost" realm.
If niether of those realms work, then:
1. set hostname correctly (mycomputer.example.com).
2. set the SASL realm to the same thing
3. restart PasswordService
4. reset the user passwords
After the realm is set, you should not have this problem again.

Wireless LAN does not work after restart

Hey
My brand new laptop suddenly went blank earlier today and when I restarted it I noticed my wireless internet won't work. It is also asking me to install some new driver, the Network Controller? I am confused as everything was working fine and suddenly it's not. Anyone any ideas? :-/

Hi,
maybe you should try to install the driver for your wireless lan card. I mean, if some application damaged the driver or installed something which interferes with the wireless lan card then you should try to fix it with an reinstallation of the driver.
Heres a [LINK|http://eu.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp] to the drivers download page from Toshiba. Pick your model and your operating system and download the driver which fits for your wireless lan card.
Greets

Keybord not working after restart/shut down

Most of the time, when I shut down or restart my iMac, my keyboard stops working. The computer doesn't see a keyboard at all. I have to restart a number of times and suddenly the keybord's working again.
What can cause this?

Which keyboard? Details, please.

Mail not working after restart

Last night I decided to shut down my iMac overnight. I usually don't but just decided too. Well, when I restarted this morning and tried to open Mail app I got a error reading
"You can’t use this version of Mail with this version of Mac OS X"
what does this mean?
I also see that the OLD iTunes icon pops up in my dock when I reboot, along with the NEWER icon (which works fine). Why would that happen? Why would BOTH be there?
I ALSO notice some other programs are missing EVERY time I restart/shut down then restart my Mac, like Skype. Why does this happen???
Help.
Thanks.

it is a 2.7GHz intel core iS and the version is OS X 10.9.

Oracle not work after restart compute

Hello
Whenever i restart my compute i got the error
ORA-12528: TNS:listener: all appropriate instances are blocking new connections
untill i restart the service from the services.
is there any solution for this
thanks

Sir,
This is my init.ora file
i am new in dba track
# Copyright (c) 1991, 2001, 2002 by Oracle Corporation
# Cache and I/O
db_block_size=8192
db_cache_size=25165824
db_file_multiblock_read_count=16
# Cursors and Library Cache
open_cursors=300
# Database Identification
db_domain=""
db_name=orcl
# Diagnostics and Statistics
background_dump_dest=E:\oracle\product\10.1.0\admin\orcl\bdump
core_dump_dest=E:\oracle\product\10.1.0\admin\orcl\cdump
user_dump_dest=E:\oracle\product\10.1.0\admin\orcl\udump
# File Configuration
control_files=("E:\oracle\product\10.1.0\oradata\orcl\control01.ctl", "E:\oracle\product\10.1.0\oradata\orcl\control02.ctl", "E:\oracle\product\10.1.0\oradata\orcl\control03.ctl")
db_recovery_file_dest=E:\oracle\product\10.1.0\flash_recovery_area
db_recovery_file_dest_size=2147483648
# Job Queues
job_queue_processes=10
# Miscellaneous
compatible=10.1.0.2.0
# Pools
java_pool_size=50331648
large_pool_size=8388608
shared_pool_size=93886080
# Processes and Sessions
processes=150
# Security and Auditing
remote_login_passwordfile=EXCLUSIVE
# Shared Server
dispatchers="(PROTOCOL=TCP) (SERVICE=orclXDB)"
# Sort, Hash Joins, Bitmap Indexes
pga_aggregate_target=25165824
sort_area_size=65536
# System Managed Undo and Rollback Segments
undo_management=AUTO
undo_tablespace=UNDOTBS1
thanks
Message was edited by:
Umesh Sharma
Message was edited by:
Umesh Sharma

Ipod classic not working after restart

What do i do if my ipod takes forever to sync and when it is ejected it doesn't have anything on it?? Anyone???, What do i do if my ipod takes forever to sync and when it is ejected it doesn't have anything on it?? Anyone???

If you are using a Macbook Pro, switch to the other USB port, as only one USB port is compatibly fast enough for iPod Syncing, the other is shared with other builtin devices like iSight, Bluetooth, hence slowing down the transfer rate and causing a timeout.
It would also help, if you disconnect all other USB devices while you are syncing an iPod classic.
Do the iPod Disk Diagnostic, it will help you troubleshoot, the cause of the iTunes Freezing,
refer to this excellent post by tt2
Look out for the high numbers, in Pending, Realloc and Temperatures.
Have a nice day!

My 3G connection is not working after updating to iOS 6.1. I have tried all possible solutions like resetting the network, restarting the iPad

My 3G connection is not working after updating to iOS 6.1. I have tried all possible solutions like resetting the network , restarting iPad , ...

The same story. No 3G after updating to 6.1. Told my daughter temporarily not to do an update on her iPad with 6.01. We've exchanged SIMs. I inserted her SIM in my iPad - 3G appeared immediately. And my SIM in her iPad with ios 6.01 also WORKS FINE. We use the same provider - Megafon Moscow. After attempting to revert SIMs to original configuration, 3G disappeared on my iPad again. Don't know what's going on with SIM during the update to 6.1

Card slot does not work after update (14/10/2011)

Card slot does not work after yesterday update (14/10/2011)! It works with my SD card month ago, but now it dosn't!!!
MacBook Pro 13 OS ver. 10.6.8

Thanks for your suggestion. I downloaded OnyX and ran the cleaning function. After restarting, I opened Help and once again the first screen appeared fine. But again most of the links did not work, though those under the "What's New" heading did work. I might add that I had previously tried a variety of suggestions posted in another thread, which included deleting from the caches folder in Home>Library several files such as com.apple.helpui and help.plist in the Preferences folder. (As noted in my previous post this evening, I also created another user but that also did not have any effect.) Any other ideas? Thanks

Dll soes not work after restart teststand

Similar Messages

Maybe you are looking for